ADDN / ALTERATION AND UPGRADATION OF OFFRS MD ACCN (45 QTRS) AT BABINA CANTT UNDER GE BABINA

Amount

Note: (i) Please refer schedule 'A' notes before quoting the tender. (ii) Amount of Schedule of credit shall be deducted off line by the department.

Demolition of existing roof treatment of any description and in any position with APP/PCC and 10mm thick backing coat below APP, etc complete all as specified and as directed .

M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in padding over roof, finished and laid to required slope complete all as specified and as directed.

Cutting grooves in brick wall 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed.

M&L for 10 mm thick rendering in cement mortar 1:4 on concrete surfaces when concrete is stil green, finishing top surface even and fair including mixing of water proofing compound as per manufacturer instruction complete all as specified and as directed. Note :- Supply only Water proofing compound shall be measured & paid separately.

Supply only integral water proofing compound complete all as specified and as directed.

M&L, Water proofing treatment with the following:- (a) First coat of bitumen primer conforming to IS-3384 @ 0.3Kg / sqm to be applied on prepared surface till the surface is properly impregnated. (b) After the application of approved bituminous primer, water proofing memberne minimum weight 3kg/sqm and minimum 3mm thick reinforced with polyesterd non woven fabric (weight not less then 160gms/sqm) shall be laid on the primed surface by torch application method as per manufactured instruction. (c) All joints and change in direction should be curved with cement mortar (1:3) mixed with SBR latex @ 200ml per bag on cement and cured well before laying of membrane.

Taking up or down, 15mm bore, existing steel tubing and connections complete all as specified and as directed.

Taking up or down, 20mm bore, existing steel tubing and connections complete all as specified and as directed.

Supplying, fixing, jointing and testing, 15mm bore, galvanised iron tubing, medium grade with all fitting such as bends, elbow, socket, reducer etc and fixed to wall or laid in floor complete all as specified and as directed

Supplying, fixing, jointing and testing, 20mm bore, galvanised iron tubing, medium grade with all fitting such as bends, elbow, socket, reducer etc and fixed to wall or laid in floor complete all as specified and as directed

Fixing only old 15mm bore galvanised steel tubing and connections including cleaning of tubes (Tubes obtained from taking down shall be used), in new or old position, fixed to wall, ceiling or laid in floor with S&F, new fittings complete all as specified and as directed

Fixing only old 20mm bore galvanised steel tubing and connections including cleaning of tubes (Tubes obtained from taking down shall be used), in new or old position, fixed to wall, ceiling or laid in floor with S&F, new fittings complete all as specified and as directed

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc., and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exceeding 10 cm but not exceeding 20 cm girth in brick walls complete all as specified and directed

S&F, 500 Ltrs capacity, rotational moulded polyethlene water storage tanks (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part I, including dismantling existing tank of any description complete all as specified and as directed.

S&F, 1000 Ltrs capacity, rotational moulded polyethlene water storage tanks (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part I, including dismantling existing tank of any description complete all as specified and as directed.

Fixing only 1000 Ltrs capacity, rotational moulded polyethlene water storage tanks (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part I, including dismantling existing tank of any description complete all as specified and as directed.

S&F, 20mm bore, ball valve, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minium weight 210 gms) complete all as specified and directed

S&F, in repair, 20mm bore, Gun metal, gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and complete all as specified and as directed.

M&L, 25mm thick, PCC 1:2:4 type B-0 using 12.5 mm gradesd stone agg as in levelling course of floors complete all as specified and directed.

M&L, screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 to receive tiles etc finished rough complete all as specified and directed.

M&L for Vitrified ceramic tiles 10mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to floor etc complete all as specified and directed.

M&L for non skid coloured joint free ceramic tiles 7 to 8 mm thick (square / rectengular), area of each tile exceeding 0.11sqm but not exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to floor etc complete all as specified and as directed.

M&L, Rendering 10mm thick in cement mortar 1: 3 on fair faces of brick work or concrete surfaces, finished rough to receive tiles etc complete all as specified and directed.

M&L for vitrified ceramic tiles 10 mm thick (square / rectangular), polished, area of each tile exceeding 0.18 sqm but not exc 0.36 sqm, in Vertical surfaces such as skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match to floor etc complete all as specified and as directed.

M&L for joint free glazed coloured tiles, 350x 250x 7mm/ 450x 350x 7mm thick for work on vertical surface, set & jointed in cement slurry and pointed in white or coloured cement to match etc complete all as specified and as directed

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick in CM(1:6) etc complete all as specified and directed.

Demolition of PCC of any description and in any position etc complete all as specified and directed

M & L, Machine cut kota stone slab flooring, 18-20mm thick, over and including 20mm thick cement screed bed in CM 1:6 laid laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M & L, Machine cut kota stone slab flooring, 18-20mm thick, in riser of steps, skirting, dado & pillar over and including 10mm thick rendering in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

M&L for 75mm thick cement concrete type C-1, 1:3:6 (using 20mm graded stone aggregate) as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

M&L for 50mm thick cement concrete type B2, 1:2:4 (using 40mm graded stone aggregate) as in floor/hardstanding finished even and smooth without using extra cement complete all as specified

M&L, 60 mm thick, machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006, M-35 grade with grey cement & pigment complete all as specified and directed.

M&L, PCC 1:4:8 type D2 using 40mm graded stone agg as in filling and mass concrete, Sub base/flooring complete all as specified and directed.

M&L, 50mm thick sand cushioning under interlocking paver block including watering & consolidation complete all as specified

M&L, PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in coping on side of path including necessary form work etc complete all as specified and directed.

Demolition of brick work, built in cement mortar complete all as specified and directed.

M & L, Brickwork with fly ash bricks (Modular size), straight or curved on plan exc 6m mean radius, built in cm (1:6), rise of hight for brick wall complete all as specified and as directed.

M & L for cement concrete type C-2 (1:3:6) (using 40 mm graded stone aggregate) in surface channels, drains and manhole foundation etc.complete all as specified and as directed.

Taking down cement plaster on brick or stone wall including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for rendering 10mm thick, in cement mortar 1:6, on fair faces of brick/concrete surfaces of walls, finished even and smooth without using extra cement on complete all as specified and as directed

M&L, rendering 5mm thick, in cement mortar 1:3, on ceiling surface and finished even and smooth with out using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick, in cement mortar 1:4, on fair faces of brick/concrete surfaces of walls, finished even and smooth without using extra cement on complete all as specified and as directed

M & L for preparation of new plastered surface and applying three coat of white wash on ceiling complete all as specified and as directed.

M & L for Preparation of new plastered surface of wall and applying two coat of oil bound distemper over a coat of alkali resistant primer complet all as specified and as directed.

M & L for preparation of new plastered surface of wall and applying two coats of cement base paint on external wall surface over a coat of white cement as primer complete all as specified and as directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) exe 1.5 Sqm but n exc 4 Sqm each etc complete all as specified and as directed

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) not exe 1.5 Sqm each complete all as specified and as directed.

Taking down shutters of any description n.exc 1 Sqm each etc complete all as specified and as directed

Taking down shutters of any description exc 1 sqm and n.exc 2 Sqm each complete all as specified and as directed.

M&L, framed work as in grills, gratings, etc with ends of bars shouldered and/ or riveted into spikes; or forged into spikes, framed guard bars; barred iron doors and similar work confirming to Fe 290. Gd-E-165 and complete all as specified and directed

S&F, factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck in side with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail and bottom rail,paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as specified and as directed.

S&F, solid PVC door frame of size 50 mm x 47 mm, made out of 5 mm plain colour PVC sheet reinforced with MS Square tube etc complete complete all as specified and as directed.

S&F, aluminum anodized barrel tower bolts of extruded section & fixed, 150 mm long complete all as specified and as directed

S&F, aluminum anodized barrel tower bolts of extruded section & fixed, 100 mm long etc complete all as specified and as directed

S&F, aluminum handles cast type anodized 150 mm size etc complete all as specified and as directed

S&F, aluminum handles cast type anodized 100 mm size etc complete all as specified and as directed

S&F,150mm floor door stopper aluminium alloy body complete all as specified and directed.

S&F, butt hinges, medium weight, cold rolled, mild steel and fixed 100 mm size etc complete all as specified and as directed.

S&F, butt hinges, medium weight, cold rolled, mild steel and fixed 75mm size etc complete all as specified and as directed..

S&F, but hinges, extruded aluminium alloy with galvanised mild steel hing pin, anodised and fixed, type C-21, 100 mm size fixed to toilet PVC doors etc complete.

S&F, 300 mm long, Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast- aluminium alloy.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, all as specified and as directed

S&F, framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete of Fe-410-W (Gde-E-250) complete all as specified and as directed.

S&F, 1.25 mm thick mild steel, plain black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc complete all as specified and as directed.

S&F, Pressed steel frames for doors, 125x60mm size with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed etc complete all as specified and as directed.

S&F, Pressed steel frames for doors, 105x60mm size with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed etc complete all as specified and as directed.

Cutting holes in brick walls built in cement mortar for inserting hold fasts and making good dismantled portion in CM 1:3 or cement conc 1:2:4 type B1 as required, exc half brick but not exc full brick wall complete all as specified and as directed.

M&L, PCC (1:3:6) type C-0 (using 12.5mm graded stone aggregate) as in filling in holes of hold fasts and back filling of chowkats complete all as specified and directed.

M & L, secound class hardwood, Plain, solid, straight chowkats and frames, wrought framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F, 18/19mm thick, prelaminated particle board, interior grade, prelaminated one side with decorative choice laminations and other side balancing white lamination fixed with screws to timber frame work etc complete all as specified and directed

S&F, 12mm thick commercial plywood, grade BWR, typeBB, fixed with screws to timber frame work etc complete all as specified and directed.

S&F, 6mm thick teak wood cover fillet lipping over 19mm thick board fixed with nail all as specified and directed.

S&F, Hasp & staple, safety type, aluminium anodized with mild steel hing pin including bolt to hing plate and fixed with screws 100mm size complete all as specified and directed.

S&F, 40 mm dia., cup board knobs fixed with nut, screw and washer of brass, polished complete all as specified and as directed.

S&F, continuous (Piano) hinges, mild steel, bright finished or electro galvanized, width of flaps (When open) 30 mm complete all as specified and as directed.

S&F, auto closing hinges 35mm of 0 crank (KH-001) OR 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete all as specified and as directed

S&F, 35 mm thick Flush shutters, factory made, solid core construction, with block board core and plywood face panels, with decorative face veneers on both faces with lipping to match complete all as specified and directed.

S&F, factory made, 35 mm thick IInd class HW glazed & skeleton shutters open rebated and prepared to receive glass gauge etc. (without sash bars) edges of framing plain chamfered or rounded fitted with cut & mitered beads for security glass/gauge etc. size of members of shutter as specified in SSR Pt I sec 8 Cl 8.20 (a), divided into squares with plain chamfered rounded, mitered and rebated sash bars etc complete all as specified and as directed

S&F, 35 mm thick IInd class HW partly paneled & Partly gauged & skeleton shutters open rebated and prepared to receive glass/gauge etc. (without sash bars) edges of framing plain chamfered or rounded fitted with cut & mitered beads for security glass/gauge etc. size of members of shutter as specified in SSR Pt I sec 8 Cl 8.20 (a), divided into squares with plain chamfered rounded, mitered and rebated sash bars etc (fabricated at site) complete all as specified and as directed.

S&F, galvanized mild steel wire cloth, 0.63 mm nominal dia of wire and average width of apertare 1.40 mm fixed with tinned tacks or galvanized wire staples etc complete all as specified and as directed.

S&F, 3mm thick, sheet glass, ordinary quality and glazing withoil putty in square in exc 0.5 sq.m in each pane etc complete all as specified and as directed.

M&L for preparation new wooden surface of any description not otherwise described over 10 cm width or girth and applying two coat synthetic enamel paint over one coat of pink primer etc complete all as specified and as directed.

M&L, preparing for new steel surfaces and applying two coats of synthetic enamel paint over one coat of red oxide primer over 10 cm width or girth complete all as specified and as directed.

M&L one coat synthetic enamel paint on old wooden surface including prepartion of old surface of any description not otherwise described over 10 cm width or girth etc complete all as specified and as directed

M&L, preparing for old steel surfaces and applying one coats of synthetic enamel paint over 10 cm width or girth complete all as specified and as directed.

S&F, in repair, Vitreous chine, wash down water closet pan (padestal pattern), white (EWC) including plastic seat of same colour of WC, closed pattern with flat bottom, and cover mild steel chromium plated hinging device complete all as specified and directed

S&F, in repair, vitreous china, squatting pan “ORISSA” pattern size 58 X 44 (CM), white, with P or S trap front or back inlet with integral foot rest (excluding flushing cistern & flush pipe) & including connection to trap & to flushing pipe anti syphonage pipe etc complete including making good to floor complete all as specified & as directed.

S&F, in repair, 10 ltrs capacity, PVC low level flushing cistern, sleek body, single flush, colour white, with inlet, float valve and handle with 32 mm dia PVC pipe 600 mm long complete all as specified and as directed.

S&F, in repair, Vitreous China Ware, Wash hand basin, white, flat back, size 550 x 400 mm size (flat back or angle back type) including cutting for and pinning ends of brackets or erecting stand and waste pipe complete all as specified and directed

Supply and fixing, Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket and railing 60cm long (all as per sample kept in GE's office) fixed with screws complete all as specified and as directed.

S&F, in repair, CP Brass, soap dish ( approximate size 160x 160 x 90mm) fixed to wall with CP brass screws etc complete all as per sample kept in GE's office and as directed.

S&F, in repair, PVC connections, 15mm size with PTMT nuts of length 450mm etc complete all as specified and as directed.

S&F, in repair, brass CP wall mixer, 15mm bore, for mixing hot & cold water, for wall, screwed down for iron pipe and fixed complete all as specified and as directed.

S&F, in repair, 15mm bore, cast copper alloy, chromium plated, angle cock with flange complete all as specified and as directed.

S&F, in repair, 15mm bore, cast copper alloy, chromium plated, two way, angle cock with flange complete all as specified and as directed.

S&F, in repair, 15mm bore, fancy type, chromium plated, bib cock, long body with flange etc complete all as specified and as directed.

S&F, brass, CP, mixer 15mm bore, central hole mixer for mixing hot & cold water for wash hand basin screwed down for iron pipe and fixed complete all as specified and as directed.

S&F, 15mm bore, Pillar tap, cast copper alloy, with capstan heads,chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed

S&F, in repair, 15mm bore, concealed stop cock, fancy type, CP, cast copper alloy, screwed down high pressure with crutch or buttor fly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F, brass chromium plated health faucet for EWC screwed down to GI tubing/fittings, 15mm bore including 1200mm long stainless steel connection complete all as specified and directed.

S&F, in repair, PVC, floor trap/Nahani trap outlet dia 75mm with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed

S&F, CP, brass, Towel ring (all as per sample kept in GE's office) complete all as specified and directed

S&F, stainless steel towel rack (all as per sample kept in GE's office) fixed to wall with CP brass screws complete all as specified and as directed.

S&F, in repair, 125 mm, Brass chromium plated shower rose with or without swivel joints, any size, including fixing of steel pipe or union and fixed all as directed

S&F, stainless steel, kitchen plate rack, overall size 900mm x 750 X 250mm make out of 0.80mm thick stainless steel sheet etc complete all as specified and directed

S&F, in repair, stainless steel sink with drainage board 1.00mm thick for kitchen or laboretory with plug, waste pipe, coupling, washers also incl cantilever cast iron brackets connecting union etc, overall size 915X460mm with bowl size 410x330x160mm complete all as specified and directed

S&F, in repair, 25 mm dia chromium plated curtain rod with CP brackets and knobs at both end (all as per sample kept in GE's office) complete all as specified and directed

S&F, PVC, bathroom cabinet with mirror of size 432mm x 311mm (all as per sample kept in GE's office) complete all as specified and as directed.

Demolition and breaking up 100mm bore drain pipes (Salt glazed ware, AC/PVC/CI or Reinforced concrete) set in cement mortar in floors or wall complete all as specified and directed

S&F, 110mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall with clamp out of 25x3mm flat Iron including bolts and nuts complete all as specified and directed

S&F, 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed

S&F, 75mm bore, PVC (SWR) pipes single socketed, in any length with clamp out of 25x3mm flat Iron including bolts and nuts rubber ring joints, fixed to wall complete all as specified and directed

S&F, 75mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed

S&F, PVC (SWR) bend, any radius, 110mm bore complete all as specified and directed

S&F, PVC (SWR) bend, any radius. 75mm bore complete all as specified and directed

S&F, PVC (SWR) junction single, (single T) equal or unequal, 75mm bore with access door complete all as specified and directed.

S&F, PVC (SWR) junction single, (single T) equal or unequal 110mm bore with access door complete all as specified and directed.

S&F, PVC (SWR) vent cowl, 110mm bore complete all as specified and directed

S&F, MS chromium plated, peg set of five, (all as per sample kept in GE's office), fixed to wall complete all as specified and directed

Demolition and breaking drain pipe (salt glazed stoneware) set in cement mortar including packing under and haunching against side of pipe for 150 mm Internal dia of pipe complete all as specified and directed

Demolition and breaking drain pipe (salt glazed stoneware)set in cement mortar including packing under and haunching against side of pipe for 100 mm Internal dia of pipe complete all as specified and directed

Concrete bed to drain 150mm bore pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in cement concrete 1:4:8 complete all as specified and directed

Concrete bed to drain 100mm bore pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in cement concrete 1:4:8 complete all as specified and directed

M&L, Salt glazed stone ware (SGSW) grade 'A' pipe, 150mm bore laid and jointed on concrete bed complete including testing complete all as specified and directed

M&L, Salt glazed stone ware (SGSW) grade 'A' pipe, 100 mm bore, laid and jointed on concrete bed complete including testing complete all as specified and directed

Excavation in trenches for foundation n.exc 1.5m wide and n.exc 1.5m in depth & getting out in soft /loose soil complete all as specified and directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25cm complete all as specified and directed

Removing excavated soil to a distance n.exc 50m & depositing where directed at a level n. exc 1.50 m above the starting point , complete all as specified and directed

Complete removal of existing treatment from old painted surface of wall by scraping watering rubbing etc complete all as specified and as directed.

M&L for applying 3mm thick wall care putty complete all as specified and as directed.

M&L for preparation of old decorated wall surfaces and applying two coat of oil bound distemper all as specified and as directed.

M&L for preparation of old decorated surfaces of wall and applying two coats cement base paint all as specified and as directed.

M&L, Preparing old plastered/unplastered surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L, Preparing old plastered/unplastered surfaces of wall and applying one coat of white wash complete all as specified and directed.

M&L, One coat of water based bitumen emulision primer @ 0.3 lit per sqm including cleaning of surface thoroughly from dust & dirt, laying water proofing treatment with polymetric memberane 3 Kg/ sqm standard consisting of 90 micron, HMHDPE torch on memberane over a coat of blown bitumen 85/25 @ 1.2 Kg/sqm on top of memberane and providing 25 mm thick sand cushioning to receive lean concrete in sunken floor complete, all as directed and as specified.

M&L for PCC (1:5:10) type E2 using 40 mm graded stone aggregate as in filling and mass concrete complete all as directed and as specified.

M&L for PCC 1:2:4 type B0 12.5 mm stone aggregate, average 25 mm thick, laid to slope required, in sunken floors all as directed.

M&L rendering 15mm thick in CM 1:3 on fair faces of brick/concrete surfaces of sunken floors mixed with WPC, finished even and fair complete (Supply only WPC shall be measured paid separately).

M&L, applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel/iron surfaces of any description over 10 cm width or girth not other wise described complete all as specified and as directed.

S&F, Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw complete all as specified and as directed.

S&F, MS steel work in tubular trusses and tubular posts, purlin including special shaped washers etc., complete using ERW or induction butt welded tubes conforming to I.S.I 1161-1998 Grade St-240 with one shop coat of zinc chromate primer paint complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out in hard/dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and as directed.

M&L PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

S&F, mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc.and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Supply only mild steel Fe-410-W (Gde.E-250) quality-A round bars 10mm dia and over including welding to angle iron and complete all as specified and as directed.

Supply only MS galvanised chain link fencing including 4mm dia galvanised wire plain fixed on both sides for straighting (weight of chain link fencing n.exc 3.50 kg/Sqm) complete all as specified and as directed.

Fixing only chain link fencing including fixing of line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and as directed.

Arboriculture work consisting of excavation of beds 0.3 M in depth and wide 0.4M for ground cover (hedge), filling bed with prepared manure, soil (50% black cotton soil required) ratio 1 sludge plus 2 good earth by Volume, including preparation of manure soil, mixing of soil to improve nutrients as required and inside coat of Anti termite chemical in bed, flooding with water, dressing including removal of rubbish & surplus earth, if any with all leads & lifts, planting of ground covers (hedge @ 4 Plant/Rm) and stacking in full and final location complete all as directed.

Taking down carefully existing aluminum / copper point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, pendants, tube light fitting, ceiling fan with regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces of walls, floors, ceiling etc to match with existing surfaces complete all as specified and directed.

M&L for concealed point wiring complete with PVC insulated and unsheathed flame retardant FRLS/FRLSH cable of 1.5 sqmm (nominal area) with stranded copper conductor single core 1100 volts grade in and including rigid PVC conduit not less than 19 mm dia, clip, with MS terminal boxes (not less than 1.0 mm thick) and painted with one coat of red oxide primer all around and two coats of black bituminous paint from out side and two coat of aluminum paint from in side including common earth dolly with 3 mm thick plastic laminated sheet top cover of approved make and colour including 1.5 sqmm green stranded copper conductor as continuous earth wire with lugs complete including cutting necessary chases on wall / ceiling surfaces for drawing of conduit & cables as required and making good disturbed surfaces of walls with CM 1:3:6 and matching with the existing surfaces including colour washing all as specified and as directed for the following :-

One light point controlled by one switch.

One Ceiling fan point controlled by one switch & regulator.

One Bell/Buzzer point controlled by one switch.

One 3/5 pin multipurpose socket out let 5/6 Amps on the same board with other switch.

One 3 pin/5 pin switch socket outlet, 5/6 Amps on independent board.

One light point controlled by two- two way switch.

Description all as per item No 154.00 here-in-before but point wiring with 2.5 sqmm, multistrand copper conductor cable for one socket outlet three pin, 6/16 Amps controlled by one switch on independent board and 1.5 sqmm FRLSH PVC insulated multi strand copper conductor cable as continous earth wire.

S&F, switch modular type, 6 Amp, one way, single phase complete all as specified and directed.

S&F, switch modular type, 16/20 Amp, one way, single phase complete all as specified and directed.

S&F, switch modular type, 6 Amp, two way, single phase complete all as specified and directed.

S&F, socket shuttered outlet 2/3 pin 6 Amp modular type multi purpose combined complete all as specified and directed.

S&F, socket shuttered outlet 2/3 pin 6/16 Amp modular type multi purpose combined complete all as specified and directed.

Modular metal flush terminal boxes with lumina plate and frame suitable for 1-2 module complete all as specified and directed.

Modular metal flush terminal boxes with lumina plate and frame suitable for 3 module complete all as specified and directed.

Modular metal flush terminal boxes with lumina plate and frame suitable for 4-6 module complete all as specified and directed.

S&F Ceiling rose, surface bakelite 65x50mm, two to three terminals complete all as specified.

S&F Lamp holder batten insulated body, cord grip pattern, complete all as specified.

S&F, Electric bell, AC 230 volt, single pole, Ding Dong type complete all as specified.

S&F, modular bell push, piano type, 6 Amp, SP, one way complete all as specified.

S&F, stepped type, electronic fan regulator, flush on the existing frame plate complete all as specified and as directed.

S&F, MCB distribution board, powder coated, double door, flush mounted complete with locking arrangement suitable for 8 way SPN, 200 Amp, 230 volt AC supply complete all as specified and as directed. .

S&F, MCB distribution board, powder coated, double door, flush mounted complete with locking arrangement suitable for 4 way SPN, 200 Amp, 230 volt AC supply complete all as specified and as directed.

S&F, Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20Amps complete all as specified and as directed.

S & F TPN distribution board double door with 415 volts rated bus bar, flush mounting with provisions for MCCBs incomer & outgoing 4 way having IP 54 protection complete all as specified and directed.

S&F, MCCB, 63 Amp, 16 KA, 4 pole, 3 phase, 415 volt, complete all as specified and as directed.

S&F, MCB SPN, 20 to 63 Amp, 240 Volts having braking capacity 10 KA complete all as specified and as directed.

S&F, MCB single pole, 6 to 40 Amp, 240 Volts having braking capacity 10 KA complete all as specified and as directed.

S&F, LED lamp 9 watt capacity operating on 230 V , AC, 50Hz supply, Pin type complete all as specified and directed.

S&F, LED Tube light fitting complete with basic all purpose surface and wall mounted LED batten with aluminium housing & intergrated electronic driver 20 watt capacity, 1182mm long and including connections from ceiling rose complete all as specified and directed.

S&F LED type Bulk head fitting in engineering plastic housing with clear prismatic diffuser 6.5 watt capacity complete all as specified and directed.

S&F, LED Tube light fitting complete with basic all purpose surface and wall mounted LED batten with aluminium housing & intergrated electronic driver 10 watt capacity 592mm long and including connections from ceiling rose complete all as specified and directed.

S&F, in repair, decorative wall light fixture made of polycarbonate, including LED Bulb 10 Watts complete all as specified and directed.

Sub main wiring using two single core, PVC insulated and unsheathed FRLS/FRLSH multi stranded copper conductor of size 10 Sqmm ( nominal area) 1100 volts grade, drawing through with and including PVC pipe of 20mm dia size with cutting & chases in wall and making good for PVC concealed conduit with and including continuous earth wire of size of 10 Sqmm PVC insulated and unsheathed FRLS/FRLSH multi stranded copper conductor 1100 volts grade, cable as earth wire and connected to main board and making good disturbed surface after taking out old unserviceable sub main wiring complete all as specified and directed. Note : Three runs cable and one run of conduit shall be considered as 1 running metre for payment purpose.

Sub main wiring using two single core, PVC insulated and unsheathed FRLS/FRLSH multi stranded copper conductor of size 6 Sqmm ( nominal area) 1100 volts grade, drawing through with and including PVC pipe of 20mm dia size with cutting & chases in wall and making good for PVC concealed conduit with and including continuous earth wire of size of 6 Sqmm PVC insulated and unsheathed FRLS/FRLSH multi stranded copper conductor 1100 volts grade, cable as earth wire and connected to main board and making good disturbed surface after taking out old unserviceable sub main wiring complete all as specified and directed. Note : Three runs cable and one run of conduit shall be considered as 1 running metre for payment purpose.

M&L for earthing complete with GI earth plate electrode 60 cm x 60 cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.50mtrs below normal ground level connected to GI earth strip 25x4mm by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electric plate No 3 of SSR Part-I connected to continuous earth wire on main switch board all as specified or indicated and testing on completion including provision of earth strip protection by 40 mm bore light grade GI pipe and watering pipe shall be 20 mm bore, medium grade including excavation & earth work in any type of soil & disposal of soi, providing alternate layers of charcoal and common salt, constr of PCC earth chamber in mix 1:3:6 type C-1 with 40mm thick RCC 1:2:4 type B-1 cover, reinforced with 8mm TMT bars 100mm C/C both ways with life hook made out oof 8mm dia bars, watering arrangement with funnel & wire mesh, complete all as specified and directed. Note. (i) The concrete pit shall be PCC (1:3:6) type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I. (ii) The unit rate includes the cost of GI pipe light grade for protection of earth strip and earh strip upto 7.5 M. (iii) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself

Taking down ceiling fans/exhaust fans/Geyser etc care fully and refixing the same all as specified and directed.

M&L, Spary painting of ceiling fans/exhaust fans/Geyser etc with one coat of white synthetic enamel paint after cleaning of internally/exeteranlly including prepration of old painted surface complete all as specified and as directed.

S&F, electric water storage heater (vertical type geysers) (BEE 5 star ratings), 25 ltrs capacity, 230 volts AC single phase with and including heavy duty fastner not less than 100mm with suitable size of nut & washer grouted in wall with complete mason work for proper mounting of geyser fastner bolt etc as directed as per site requirement, making necessary inlet/outlet water connection and electric connection, testing on load complete all as specified and as directed.

S&F, PVC connection 450 mm long for cold/hot water heavy duty made out of double layer Nylon & wire fabric at pressure 6Kg/CM both side, CP brass 15mm bore coupling or nuts complete all as specified and as directed.

S&F, GI pipe, 15mm bore, medium grade with all fittings like elbow, nipple, union, Tees, socket etc complete fixed on floor, on wall surface or concealed in wall / crossing the walll up to 30 cm thick for geyser inlet connection from tank outlet to gysers inlet and geysers outlet to bathroom tap/wash basin mixture connection with and including clamp etc complete all as specified and directed.

Material and labour for cutting & screwing existing steel tubing 20/15mm dia bore size for alternations or additions required for connection with inlet pipe of geyser complete all as specified and directed.

S&F, gun metal, globe or gate valve, 15 mm bore with iron wheel head, screwed both ends for iron pipes complete all as specified and directed.

S&F, XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured electric 50Sqmm 3.5 core cable ( heavy duty) stranded aluminium conductor including cable glands, cable lugs etc to suit the cable size, 1100volt grade, laid in trenches or fixing along the poles or passing trough the pipe or laid under floors or through walls/ducts etc complete all as specified and as directed.

M&L for GI bracket made out of 32mm bore GI pipe light grade, 1.20 mtr long, bend to required shape & size and connected with FI clamp of suitable size, nuts, bolts etc as directed for mounting building security light complete all as specified and directed.

Taking down existing vintage HPSV/CFL/ LED type building security Light fitting and replacing the same with S&F, Energy efficient, LED type, building security light fitting, Pressure die cast aluminium housing with heat resistant toughened glass & IP66 protection, 30 watts (with lens) with Luminous Efficacy more than 100 Lm/Watt and Power Factor not less than 0.95 all as specified and directed.

S&F, fresh air fan 200 mm sweep, noiselss, light weight, rust proof body, self closing louvers and blades complete with all arrangment of making hole complete all as specfied and as directed.

S&F, BEE 5 star rating energy efficient ceiling fan 1200mm sweep , with min air delivery 210 cum/min, incl down rod & all accessories incl required length of 3 core, 1.00 Sqm , PVC multistranded copper conductor, PVC connector for proper hanging of fan & testing complete all as specified and directed.

Excavation in trenches trenches n exc 1.5 m wide and n exc 1.5 m in depth for poles, cable, foundations etc including getting out in hard / dense soil, complete all as specified & directed.

M&L for fine, dry and clean sand (river sand) free from sharp materials in trenches for cushioning of cable or filling in trences around underground cable in ducts, inside substation including gently punning complete all as specified and directed . Note:- The total thickness of sand shall be measured after punning.

Supply and laying of sub class B old size bricks old class ‘B’ for protection of underground cable laid flat i.e. Length of brick shall be laid across the length of cable complete all as specified and directed.

S&F GI tubing size 80 mm bore, light grade, ISI marked, complete with all fittings, laid in trenches / floors complete all as specified and directed.

GUPTA ENGINEERING WORKS

Deepesh Electricals

M/s Bijender Singh

Vee kay construction