REPAIR AND MAINTENANCE TO FLOORING, PLASTERING, JOINERY, ROOFING, ETC AND OTHER CONNECTED B/R WORKS STN HQ, 1690 FPO AND MES AT SHARIFABAD MIL STN UNDER AGE (I) CIF (K).

Amount

Demolition of cement concrete un reinforced in ground floors and pavings not exceeding 15cm thickness (below or above ground level) including disposal of unserviceable materials,debris and rubbish to a distance not exceeding 100 metre, complete all as specified and as directed by the Engineer-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed by the Engineer-in-Charge.

Taking down plastering in cement lime or cement mortor on brick or stone work etc. including racking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed by the Engineer-in-Charge.

Demolition of brickwork or stone/boulder masonry, build in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles, complete all as specified and directed by Engineer-in-Charge.

Brick work with sub class `B' bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6, complete all as specified and directed by the Engineer-in-Charge.

Rendering 15mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed by the Engineer-in-Charge.

Rendering 15mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:4, surface finished even and smooth without using extra cement, complete all as specified and directed by the Engineer-in-Charge.

Non skid ceramic coloured tiles Ist quality 7 to 8mm thick, (square/ rectangular), area of each tile exceeding 0.06sqm, but not exceeding 0.11sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, complete all as specified and as directed by the Engineer-in-Charge. Note: Colour and shade of tiles shall be approved by AGE(I) and contractor shall not have any claim whatsoever on this account.

Glazed ceramic tiles, coloured, of size 350mm x 250mm/450 mm x 350mm, thickness not less than 7mm as in vertical surfaces such as skirting/dado etc, set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match the shade of tile, fixed over and including 10mm thick rendering (bedding layer) on brick/concrete surface in cement mortor 1:4, complete all as specified and as directed by the Engineer-in-Charge. Note: Colour and shade of tiles shall be approved by AGE(I) and contractor shall not have any claim whatsoever on this account.

Vetrified Ceramic tiles (Light Shade) 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured, laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, complete all as specified and as directed by the Engineer-in-Charge. Note: Colour and shade of tiles shall be approved by AGE(I) and contractor shall not have any claim whatsoever on this account.

Non skid ceramic coloured tiles Ist quality 7 to 8mm thick, (square/ rectangular), area of each tile exceeding 0.11sqm, but not exceeding 0.18 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, complete all as specified and as directed by the Engineer-in-Charge. Note: Colour and shade of tiles shall be approved by AGE(I) and contractor shall not have any claim whatsoever on this account.

Vitreous China, wash hand basin, flat back white of size 550mm x 400mm including brackets, brass CP waste coupling 32mm dia with long screwed shank and fly nuts, 32mm dia PVC waste pipe, chain and plug, porcelain stopper including cutting for and pinning in ends of brackets or erecting stand, fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

Vitreous Chinaware squatting pan, orissa pattern size 580mm x 440mm with integral foot rests, white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, including provision of lime concrete, making connections to trap and to flush pipe etc. and making good to floors, fixed in repairs, complete all as specified and directed by the Engineer-in-Charge.

PVC valveless, syphonic action type flushing cistern, 10 litres capacity, plunger type, low level, white with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 60cm long, fixed in repair, complete all as specified and directed by the Engineer-in-Charge.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering, complete all as specified and directed by the Engineer-in-Charge

Pre-painted galvalume aluminum zinc coating GI based corrugated profile steel sheet 0.50mm thick of colour as approved by AGE(I), having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed by the Engineer-in-Charge.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of colour as approved by AGE(I), having tensile strength of 550 Mpa as in roof covering/cladding to ridges, valley gutters etc. fixed with self tapping screws, complete all as specified and directed by the Engineer-in-Charge.

Bib taps, 15mm bore, cast copper alloy, chromium plated, with crutch or butter fly handle, screwed down, screwed for iron pipe, or brass ferrule and fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

Stop valves/angle valve 15mm bore, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repairs, complete all as specified and directed by Engineer-in-Charg

Brass CP wall/basin mixer,15mm bore, for mixing hot and cold water screwed down for iron pipe and fixed in repairs, complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered / unplastered surfaces of walls and applying two coats of distemper oil emulsion over one coat of primer, complete all as specified and as directed by Engineer-in-Charge.

Preparation of old decorated plastered or unplastered surfaces of wall including cleaning by brooming down or with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots etc. and applying two coats of oil bound distemper over a coat of chalk whiting on wall, complete all as specified and as directed by Engineer -in -Charge.

Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali-resistance primer paint, complete all as specified and as directed by the Engineer-in-Charge.

Plain cement concrete 1:2:4, type B-1 using 20mm graded crushed stone aggregate as in lintels upto 1.50 metres clear span, steps, seismic and other similar bands, coping, bed plates for serving hold fasts, filling in mild steel frames etc. and the like including weathering slighting rounded or chamfered angles and throating, and use of form work (straight or curved), complete all as specified and as directed by the Engineer-in-Charge.

Anodised aluminium frame (powder coated minimum thickness of powder coating 50 micron) for doors, windows,partation wall, ventilators with one or more rebates including joining cleat for fixing etc., complete all as specified and asdirected by Engineer-in-Charge.

Anodised aluminium (powder coated minimum thickness of powder coating 50 micron) door shutters, powder coated of any colour aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, anodised aluminum snap beading screws etc. frame will be fixed to wall , complete all as specified and directed by the Engineer-in-Charge.

Anodised aluminium (powder coated minimum thickness of powder coating 50 micron)window and ventilator shutters, powder coated of any colour sliding/ hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21 100mm long (2 Nos.) suitable handle (1 No.), complete all as specified and directed by the Engineer-in-Charge.

Mortice lock, vertical type 4 levers,, size 100 mm, complete all as specified and directed by the Engineer-in-Charge.

Prelaminated particle board, 12 mm thick, interior grade, prelaminated on boat side with decorative choice lamination and fixed with screws to aluminum frame work, complete all as specified and as directed by the Engineer-in-Charge.

Tinted sheet glass, 4 mm thick glazing with in alm frames including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings as required, complete all as specified and as directed by the Engineer-in-Charge.

Door closer hydraulically regulated, designation No. 2, universal type, uitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed, complete all as specified and as directed by the Engineer-in-Charge.

Dismantaling boarding/false ceiling of any description fixed in any postion with nails, complete all as specified and as directed by the Engineer-in-Charge. .

GI frame work size of grid 605 x 605 mm for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from sofit at approx 900 mm centre to centre with GI cleat and steel expansion fasterner with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips acress the intermediate channel at 457mm centre to cnetre including hangers 6mm dia.GI (upto 1200mm length) adjusting level fixed tp roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm ling and expansion hold fasterner 12.5mm dia 40mm long including 4mm thick non asbestos fibre cement building boards fiuxed or laid/inserted to timber/GI frame work complete all as specified and directed by Engineer-in-Charge.

2nd class soft wood boarding, 15mm thick, as in wall panelling supplied & fixed with nails in any situation, Planed one side and edges tongued and grooved or rebated, complete all as specified and as directed by the Engineer-in-Charge.

Dismantling timber scantling under 40 sq. cm in section in fillets, rails, posts, rafters, purlins, etc., unframed work, complete all as specified and as directed by the Engineer-in-Charge.

Plain fillets. square, rectangular or triangular in section, made of 2nd class soft wood (Kail), wrought, secured with nails or brads, sectional area exceeding 13sqcm but not exceeding 25 sqcm, complete all as specified and as directed by the Engineer-in-Charge.

Note :- An amount of Rs.10,750.00 on account of credit schdule for Sch 'A' Part-II Shall be deducted from the total amount of BOQ to arrive at the contract sum.

JK BUILDERS AND ENGINEERS (BID ID -3152522)