GE(S)/M-49/2021-22

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (unreinforced) inground floors and pavings n. exc. 15cm thickness (below or above ground level) complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 Sqm each and removing from site, complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but not exc 4.00 Sqm each and removing from site, complete all as specified and directed.

Taking down shutters of any description exc 1.0 Sqm but not exc 2.0 Sqm each and removing from site, complete all as specified and directed.

Demolition of walls and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slab/blankets, any thickness, including cover fillets. complete all as specified and directed.

Excavating in trenches in any type of soil, n. exc. 1.5 m wide and n. exc. 1.5 m in depth, for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc n. exc. 10 sqm on plan and n.exc 1.5 m in depth and getting out complete all as specified and directed.

Removing excavated material (soil) n.exc. 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

M&L for PCC 1:5:10, type E-2 (using 40mm graded crushed stone aggregates) as in sunken floors complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, haunching, benching, kerbs , mud stops, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6 Mtr mean radius, built in CM 1:6, including demolition of existing brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, including removal of deberies out of MoD land complete all as specified and directed.

M&L for brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick wall, built in CM 1:4 including demolition of existing structure, complete all as specified and directed.

S&F 40mm thick 2nd class hardwood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9mm thick BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

S&F 35mm thick factory made wire guazed/glazed and skeleton shutters (1st class softwood), open rebated and prepared to receive wire cloth, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing wire cloth etc. sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) and fitted to chowkats at site, complete all as specified and directed.

S&F Factory made solid panel PVC door shutter (Wood garin colour sheets on both sides) 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded wood grain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of wood grain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site, complete all as per specifications & drawing.

S&F Solid PVC door frame of size 50mm x 47mm, made out of 5mm thick plain colour PVC sheet reinforced with MS Square tube, suppling & fixing in opening at site, complete all as per specifications & drawing.

S&F factory made 18mm (+ 0.7mm) thick PVC cupboard shutter, printed one side with coating of ultra voilet chemical, glossy/mat finish incl. 100% termite/water proof, fire retardant, Eco friendly, density not less than 600Kg/cbm finish at all edges for making edges lipping/bending, complete as per direction of Engineer-in-Charge and manufacturer's specifications.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanised 30mm width of flaps (when open), complete all as specified and directed.

S&F 125mm size hasp and staple, safety type aluminium anodised including bolts to hinge plate and fixed with screws.

S&F stainless steel handle bright finish of size 100mm long complete all as specified and directed.

S&F ball catcher with proper magnetic effect fixed with shutter, complete all as specified and directed.

S&F 100mm long butt hinges, medium weight, cold rolled mild steel, (ISI) marked complete all as specified and directed.

S&F 100mm long stainless steel butt hinges, complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F 200mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F mild steel pressed handle, ovel type, stove enamelled black 125mm long, (ISI) marked complete all as specified and directed.

S&F 125mm long extruded aluminium alloy handle, cast type, anodised complete all as specified and directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, (ISI marked), complete all as specified and directed.

S&F galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

S&F "as in repair" 25mm bore stainless steel curtain rod with 1.0mm thick wall thicness and each length not more than 1.5m including a pair of brackets and knobs with each length/piece, fixed on doors and window openings for hanging curtains complete all as specified and directed.

S&F stainless steel wall hanger set of six of size 450mmx35mmx3mm complete all as specified and directed.

S&F Box type steel windows and ventilators, comprised of tubular frame and shutters made out of 1.25mm thick MS sheet tube, factory made with double side hung wire gauged shutter & glass/glazed shutter (wire cloth and glass panes shall be measured and paid separately under respective items of BOQ) with steel handle and steel peg stay dovetailed or welded including 2 Nos. tower bolts of 150mm long for each leaf and 10mm square bar grills at spacing as shown on drawing, welded to FI frame work including other fittings such as hinges, handles, tarred hold fasts etc. fixed in PCC blocks including two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as shown on drawing No. CEPZ/TD-354/09 sheet 1/3 to 3/3.

S&F pressed steel frame of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate including filling of PCC 1:3:6 type C-0 (using 12.5mm graded stone aggregates) in frames/hold fast blocks, including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&F pressed steel frame of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate including filling of PCC 1:3:6 type C-0 (using 12.5mm graded stone aggregates) in frames/hold fast blocks, including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick (ISI marked) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc including dismantling of existing plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

M&L Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick (ISI marked) of any colour having tensile strength of 550 Mpa as in ridge/valley , gutter or straight flashings etc including dismantling of existing plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

M&L for bitumen hot blown any grade, applied hot, two coats to concrete / plastered surfaces at the rate of 1.5 Kg per Sqm per coat and applying polythene film black 50 micron, complete for sunken floor slab and embedded in side wall / covered fillet, complete all as specified and directed.

M&L False ceiling of 9.5mm thick gypsum tiles (600x600mm) laminated with PVC film on the face side & metalised polyester film on the back side with all four edges sealed with PVC film (shade either plain white or crack) fixed using T grid/Cross-T/Wall angle/level clip & suspenders of standard galvanised sections in a grid size of 600x600mm, including taking down existing ceiling board & grid work etc of any type/pattern complete all as specified and directed.

M&L for 25mm PCC 1:2:4 type B-1 (using 20 mm graded aggregate) as in floors laid in panels n. exc. 2.5 Sqm with top finished the surface even and smooth without using extra cement including glass dividing strips as per site requirement complete all as specified and directed

M&L for 50mm PCC 1:2:4 type B-1 (using 20 mm graded aggregate) as on roof slab including finishing the top roof surface even and smooth including necessary wire mesh of adequate size without using extra cement complete all as specified and directed

M&L for 75mm thick cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection and paving, laid in slope, finished even and fair including making joints at every 2.5 mtr and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight, complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick, area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floors etc, set and jointed (joint free) in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:6 for laying floor finishes, complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 300mm x 450mm x 7mm thick on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including rendering 10mm thick in CM 1:4 and finished rough to receive tiles complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18-20mm thick over and including 20mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing as in floors / cills etc, and moulding at edges if required including demolition of existing stone slabs and tiles any description or thickness complete all as specified and directed.

M&L for machine cut kota stone tiles as in riser of steps / pillars / skirting / dados 18-20mm thick, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and rounding the edges of kota stone laid over and including 10mm thick rendering in CM 1:4 to recieve stone slab, including demolition of existing stone slabs and tiles any description or thickness complete all as specified and directed.

M&L for marble work (Green / Black marble Bhaislana Zebra) 18-20mm thick (table rubbed and polished) as in cooking plateform, window cills, jambs, steps and like over and including 15mm thick screed in CM 1:4 including pointing with white cement (1:2) using marble dust with admixture of pigment to match the marble shade including rounding the exposed edges full round, and making hole for gas pipe, complete all as specified and directed.

M&L for 10mm thick rendering in CM 1:3 on brick work or concrete surface of walls/floors in sunken portion, surface finished even and smooth without using extra cement, mixing and including WPC @ 0.200ml/bag of cement, complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:3 on concrete surfaces of ceiling / top and sides of chajjas/facia of roof projection including necessary formwork, finishing the surface even and smooth without using extra cement, including taking down existing cement plaster on brick walls or stone walls of any description etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L for 10mm thick rendering on faces of brick work or concrete surfaces of walls in cement mortar 1:6, finished even and smooth without using extra cement including taking down existing cement plaster on brick walls or stone walls of any description etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L for 15mm thick rendering in two layers (5mm thick in CM 1:4 over 10mm thick in CM 1:6) on brick work and concrete surfaces of wall, finished the surface even and smooth without using extra cement, mixing and including WPC @ 200ml/bag of cement, including taking down existing cement plaster on brick walls or stone walls of any description etc. including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of old surfaces of walls including washing down, rubbing, brooming down with wire brush scrapping down smoke, roots, moulds, salts and treading oil and greasy spots and applying one coat of white wash, complete all as specified and directed.

M&L for preparation of newly plastered surface of ceiling and applying three coats of white wash, complete all as specified and directed.

M&L for preparation of old surfaces of ceiling including washing down, rubbing, brooming down with wire brush scrapping down smoke, roots, moulds, salts and treading oil and greasy spots and applying one coat of white wash, complete all as specified and directed.

M&L for preparation of old surfaces of walls including washing down, rubbing, brooming down with wire brush scrapping down smoke, roots, moulds, salts and treading oil and greasy spots and applying one coat of oil bound distamper complete all as specified and directed.

M&L for preparation of old surfaces of walls including washing down, rubbing, brooming down with wire brush scrapping down smoke, roots, moulds, salts and treading oil and greasy spots and applying one coat of washable distamper complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and making the surfaces smooth by applying 2mm thick wall care putty and applying two coats of washable distemper, complete all as specified and directed.

M&L for preparation of old surfaces of walls including washing down, rubbing, brooming down with wire brush scrapping down smoke, roots, moulds, salts and treading oil and greasy spots and applying one coat of cement based paint complete all as specified and directed.

M&L for preparation of newly plastered surface of external wall and applying two coats of cement base paint over a coat of alkali resistant primer including curing, before and after painting complete all as specified and directed.

M&L for preparation of old surfaces of walls including washing down, rubbing, brooming down with wire brush scrapping down smoke, roots, moulds, salts and treading oil and greasy spots and exterior Acrylic emulsion paint complete all as specified and directed.

M&L for preparation of newly plastered surfaces of external wall and applying two coats of exterior Acrylic emulsion paint over a coat of alkali-resistant priming paint complete all as specified and directed.

M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/ltr and UV resistance as per IS 15489:2004, Alkali & fungle resistance, dirt resistance exterior paint of required shade (company depot Tinted) with silicon additives @ 1.43 ltr/10 Sqm over and including priming coat of exterior primer applied @ 0.90ltr/10 sqm over new surfaces complete all as specified and directed.

S&F 3mm thick plain sheet glass, ordinary quality and glazing with oil putty or fixed with beads / clips, in square not exc 0.50 Sqm in each pane, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames, glazed with putty or fixed with beads / clips,complete all as specified and directed.

S&F 3mm thick figured sheet glass, ordinary quality and glazing with oil putty or fixed with beads / clips, in square not exc 0.50 Sqm in each pane, complete all as specified and directed.

M&L for preparation of old surfaces of steel & iron work of any description exc 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of new surfaces of steel & iron work of any description exc 10cm width or girth and applying two coats of synthetic enamel paint, over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old surfaces of wood & wooden of any description exc 10cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Disconnecting rotational moulded polyethlene water storage tank of capacity 1000 Litres, any description, setting aside for repair, cleaning etc, and hoisted reconnecting and refixing in same position including cleaning with bleaching powder removing scaling etc, and provision of new GI fittings, inlet/outlet washout, overflow pieces long nipples, checknuts & washer etc, complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tanks of capacity 1000 litres three layers (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I complete including 20mm dia PVC ball valve high pressure with poythene float and dismantling of existing PVC tank of any capacity complete all as specified & directed

Cleaning and removing all scale and dirt, etc from tanks of any capacity and from mouth of circulating pipes, etc complete all as specified and directed.

M&L for 15mm bore steel water tubes 'medium grade' galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, including taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to storecomplete all as specified and directed.

Description all as per srl item No 72 here-in above but except steel water tubing complete all as specified and directed.

M&L for 20mm bore steel water tubes 'medium grade' galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, including taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to storecomplete all as specified and directed.

Description all as per srl item No 74 here-in above but except steel water tubing complete all as specified and directed.

M&L for 40mm bore water tubing 'light grade' galvanised, including short length, fixed as spout in wall of sunken portion of toilets complete all as specified and directed.

S&F in replacement 15mm bore chromium plated, fancy type stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete all as specified and directed.

S&F "as in repair" 20mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F "as in repair" 15mm bore bib tap with flange, fancy type, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F "as in repair" chromium plated tubular towel rail, 20mm dia 'D' type, 60cm long between flanges, complete all as specified and directed.

S&F in replacement PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

S&F "as in repair" CP soap dish stainless steel of size 160mmx160mmx90mm fixed to walls with chromium plated brass screws complete all as specified and directed.

S&F "as in repair" CP Shower rose of size 150mmx150mm with swivel arm, stainless steel/CP brass, including fixing to steel pipe or union complete all as specified and directed.

S&F "as in repair" Jet Spray (with 1.50 Mtr tube), fixed to EWC and angular stop cock/valve, complete all as specified and directed.

S&F 15mm bore chromium plated brass central hole single lever WHB mixture, for mixing hot and cold water with 450mm long braided house 20 cartriage size, screwed down, high pressure, screwed for iron pipe, complete all as specified and directed.

S&F stainless steel Grating doom 75mm dia fixed in floors complete all as specified and directed.

S&F "as in repair" plastic water closet seat cover, closed pattern with flat bottom, mild steel chromium plated or aluminised hinging device (colour of cover should match with water closet) complete all as specified and directed.

S&F Vitreous China urinals, flat back , bowl size 330mmx250mmx450mm white, including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) including spreader, CP coupling, waste pipe complete all as specified and directed.

S&F "as in repair" Vitreous china wash basin, white flat back of size 630mm x 450mm including 32mm size CP waste coupling full thread and 32mm dia PVC waste pipe, brackets and cutting for and pinning in ends of brackets or errecting stand, complete all as specified and directed.

S&F "as in repair" vitreous china wash down water closet pan (pedestal pattern), white including plastic white cover closed pattern with flat bottom and mild steel chromium plated hinging device including connections to drain or outgoing pipe and to flushing pipe anti syphonage pipe etc, complete all as specified and directed.

S&F "as in repair" Vitreous china squatting pan of 'Orissa pattern' of size 580mm x 440mm, white with CI ‘P’ or ‘S’ trap, front or back inlet and foot rests of any pattern (including fixing of flush pipe) and connecting etc. including provision of cement concrete bedding, complete all as specified and directed.

S&F "as in repair" PVC low level flushing cistern, valveless, syphonic action type, 10 litres capacity with inlet ball valve and handle with and including brackets and PVC bend pipe 60/90cm long etc, complete all as specified and directed.

S&F "as in repair" PVC ball valve, high pressure with polythene float and flynut, screwed for iron pipe or brass ferrule and fixed to 20mm bore pipe complete all as specified and directed.

S&F "as in repair" 75mm bore cast iron floor trap with stainless steel CP grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified and directed.

M&L 100mm dia cast iron (sand cast) soil, waste vent pipes in any length with or without ears fixed with cement joints and tested, laid in trenches or floors including demolition and breaking up existing drain pipes set in cement mortar complete all as specified and directed.

M&L 75mm dia cast iron (sand cast) soil, waste vent pipes in any length with or without ears fixed with cement joints and tested laid in trenches or floors including demolition and breaking up existing drain pipes set in cement mortar complete all as specified and directed.

M&L 75mm dia cast iron (sand cast) soil, waste vent pipes in any length with or without ears fixed with cement joints and tested fixed to walls including demolition and breaking up existing drain pipes set in cement mortar complete all as specified and directed.

M&L "as in repair" (sand cast) 100mm dia cast iron bends with ovel access door and jointed with neat cement paste complete all as specified and directed.

M&L "as in repair" (sand cast) 75mm dia cast iron bends with ovel access door and jointed with neat cement paste complete all as specified and directed.

M&L "as in repair" CI (sand cast) 100mm dia cowl cap complete all as specified and directed.

Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete and making good disturbed surfaces of walls, floors to match with existing specifications and keeping aside serviceable items for reuse within the same bldg and removing UNSV items from site, complete all as specified and directed.

M&L for point wiring for one light point / fan point / bell point controlled by one switch with 1.5 Sqmm PVC insulated unsheathed copper conductor single core multistranded FRLS cable and 1.5 Sqmm PVC insulated unsheathed copper conductor single core multistranded FRLS (green colour) cable as earth lead drawn in and including connected non metallic rigid PVC conduit including CI/MS terminal box of required size including 3mm thick plastic laminated top sheet cover including cutting chases to walls and making good the disturbed surfaces to match with the existing specifications, complete all as specified and directed.

Description all as per srl item No. 104.00 here-in-before but for 5 pin 5 amp socket outlet point on independent board controlled by one switch 5 Amps one way, etc complete all as specified and directed.

Description all as per Srl item No. 104.00 here-in before but for one 3/5 pin 15Amps socket outlet on independent board using 2.5 Sqmm copper conductor FRLS cable, complete all as specified and directed.

S&F Switch piano flush button, single pole, one way, 5 Amps, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F Switch piano flush button, single pole, one way, 15 Amps, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F socket outlet, flush type 3 pin, 5 Amps, flush type 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F Socket outlet, 3 Pin, 5 and 15 Amps, multipurpose, 2 in 1, flush type, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F ceiling rose, surface bakelite, 3 terminals, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F lamp holder insulated body with back plate for batten fittings with polycarbonate body, complete all as specified and directed.

S&F fan step regulator, step type suitable for 1200/1400mm sweep ceiling fan, hum free, 240 Volts and connecting electrically, complete all as specified and directed.

M&L for submain wiring with two single core FR PVC insulated cable 2x6 sqmm (nominal dia) copper conductor (multistrand) and drawing in and including PVC concealed conduit pipe, ISI marked including 1x6 sqmm multistranded copper conductor FR PVC green insulated unsheathed cable for earth continuity, complete all as specified and directed. Note : Three runs of wire shall be measured as one unit.

S&F LED lamp 12 watt complete all as specified and directed.

S&F surface mounted 1x20 Watt LED tube light fittings (4 feet long), prewired, decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, enviornmental friendly, energy saving efficient ready to use pack 20 Watt LED 6500 K and making connection using 3 core, 0.50 sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc, complete all as specified and directed.

S&F bulk head 10 W LED light fitting 6000K, IP 43 in engineering plastic housing with clear primatic diffuser complete with all accessories, connecting electricaly to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm complete all as specified and directed.

S&F surface mounted 1x10 Watt LED tube light fittings (2 feet long), prewired, decorative ultra slim square profile LED lighting fixture with extruded polycarbonate, enviornmental friendly, energy saving efficient ready to use pack 20 Watt LED 6500 K and making connection using 3 core, 0.50 sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc, complete all as specified and directed.

Supply, fixing and testing of 20W energy saving LED Street Light luminaire. IP 65, AC 230 volts, LED Street Light shall be made up of Pressure Die Cast aluminum housing with black epoxy polyester powder coating for long life and toughened glass visor fitted in frame, secondry optical lens for superior light distribution efficiency 100Lm/W making connections with street light/ building security light box or OH line using PVC insulated and sheathed single core multi stranded copper conductor cable of size 1.5 Sqmm including suitable size of brackets and light grade pipe for maintaining of fittings complete all as specified and directed.

Note for srl item No 116.00-119.00 above 1. Driver shall be potted anti-vibration types. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be provided. 3. CRI (Colour Rendering Index) of fixture shall be > 70. 4. CCT (Colour Co-related Temperature of fixture shall be 5700K + 300 K. 5. System Lumen Efficacy shall be > 100 Lm/W. 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 5 years guarantee shall be provided by contractor supported by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type. 10. The defect liability period of LED light shall be 05 years from the certified date of completion & the contractor shall replace/repair the defective fitting within 07 days after handing over to contractor for replacement/repair. 11. CA No. shall be written on each fitting before installation. 12. The name of manufacturer to be embossed on the fitting. 13. The fittings shall have arrangement so that maintenance required, if any can be carried out from Top cover.

S&F in replacement of GI tubing light grade 40 mm bore cut to size and fixed along the pole for cable protection including clamp 02 Nos of size 25x4 mm, nut bolts , washers etc all as required at site including taking out old one complete all as specified and directed.

S&F "in replacement" sheet metal enclosure MCB distribution board, double door, single pole & neutral 240volts 08 way with IP-54 IK-09 protection complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification, complete all as specified and directed.

S&F "in replacement" sheet metal enclosure MCB distribution board, double door, single pole & neutral 240volts 4 way with IP-54 IK-09 protection complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification, complete all as specified and directed.

S&F MCB single pole, 240 Volts, 6-32 Amps with repturing capacity 10 KA 'C' Curve complete all as specified and directed.

S&F MCB single pole and neutral, 240 Volts, 25 to 32 Amps with repturing capacity 10 KA 'C' Curve complete all as specified and directed.

S&F electric water heater storage type, of capacity 25 ltr, BEE 5 star rated and including taking out existing water heater of any type and size and depositing to MES store yard etc, complete all as specified and directed.

S&F ceiling fans with blade, down rods, electronic regulator and accessories 230volts, 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) including making connections using 3 core 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose to fan, including testing to ensure efficient functioning and including taking out existing ceiling fan of any type and size and depositing to MES store yard etc, complete all as specified and directed.

Supply and laying in trenches or fixed to wall/pole or passing through ducts or pipe, cable LT 1100 volts grade heavy duty, XLPE insulated , armoured heavy duty electric cable , with aluminium conductor of size 10 Sqmm x 2 core complete all as specified and directed. Note:- Excavation and earth work, sand cushioning, brick cover and protection pipe etc. shall be measured and paid for separately.

M&L for dry clean fine river sand as in sand cushioning to underground cable 8cm below and 15cm above the cable including punning down of sand layer complete all as specified and directed. Note :- Punned thickness shall only be measured and paid.

M&L for brick protection with sub class 'B' old size brick well burnt laid flat for cable protection abutting each other laid dry with width equal to length of brick complete all as specified and directed.

M&L for earthing complete with galvanised GI earth plate electrode of size 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25 Mtr deep below normal ground level) with top edge of earth plate not less than 1.5 Mtr below normal ground level, connected to galvanised earth lead wire 4mm dia by means bolt, nuts, check nuts and washer made of galvanised iron or steel including earth work in any type of soil, charcoal dust and salt layers 15cm thick all around the earth plate as shown in electrical plate No. 03 of SSR Part-I 2009 including 20mm bore GI watering pipe 'medium grade' with funel and wire mesh and 15mm bore GI protection pipe 'light grade' from earth pit to main board including PCC pit in cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) and including angle iron frame of size 40x40x3mm with hold fast embeded in PCC, RCC pit cover with suitable handle and earth work and removal of surplus soil to a distance not exc 50 Mtr, complete all as required at site and directed.

M/S HIMANSHU BUILDERS

Bidder Name

M/S NARESH KUMAR SHARMA

M/S HIMANSHU BUILDERS