REPAIR AND REPLACEMENT ROOF SHEETS, RAIN WATER PIPES, WPT, ANTI TERMITE TREATMENT INCLUDING PETTY REPAIRS AND MISC WKS AT INS HAMLA UNDER GE(NW) BHANDUP

Amount

M&L for preparation of old decorated wooden surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old decorated steel surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for cutting out cracks (not exc 5mm) to V-section in existing wall/chajjas and cleaning out and filling up with Dr fixit crack seal including necessary scaffoldings complete all as specified and as directed.

Taking down cement mortar or lime plaster of any description from stone or brick wall etc including raking out joints, hacking for key scrubbing down with water and disposing off the rubbish materials out side MD and including necessary scaffoldings complete all as specified and directed.

M & L for Rendering 15mm thick in (1:6) CM on fair faces of brick work or concrete surfaces of walls and finishing even and smooth without using extra cement complete all as specified and directed.

M & L for preparation of new plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of alkali resistant primer using roller etc complete all as specified and directed.

M & L for preparation of old plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of alkali resistant primer using roller etc complete all as specified and directed.

M & L for preparation of old plastered surfaces and applying two coats of white wash on wall complete all as specified and directed

M & L for rendering 5 mm thick in CM 1:3 as in ceiling finishing even and smooth (with out using extra cement) etc complete all as specified and directed.

M&L for preparation of old plastered surfaces and applying two coats of white wash on ceiling etc complete all as specified and directed

M&L for preparation of new plastered surfaces and applying three coats of white wash on ceiling etc complete all as specified and directed

M & L for Rendering 20mm thick in (1:4) cm (in two coats (15+5mm) with both coats mixed with liquid water proofing compound, surface finished even and fair without using extra cement complete all as specified and directed. ( Note : WPC will be measured separately).

M&L for for preparation of new plastered surfaces of walls, chajjas, slab projections and applying two coats of 100% Anti fungal acrylic emulsion paint in approved shade over a coat of primer and including necessary scaffolding complete all as specified and as directed.

M&L for for preparation of old plastered surfaces of walls, chajjas, slab projections and applying one coats of 100% Anti fungal acrylic emulsion paint in approved shade over a coat of primer and including necessary scaffolding complete all as specified and as directed.

M&L for Removal of plant growth by injection with chemical glyphospate solution ( 4 % conceneration ) @ 20ml or till refuse by cutting or injection in stem of plants or roots at 30mm. The area shall then be sprayed with solution 25ml glyphosphate ( 4% concent) dulited with 1 ltr of water. All roots / plants shall be removed completely and making good the distrubed surface and painted with cement base or acrylic paint all as directed by EIC.

Dismantling/Demolition of existing roof terracing of cement/brick concrete(un-reinforced) and existing water proofing treatment of any thickness in any position on top of roof of building, cleaning surface of roof with brush/mechanical brush and with water throughly to romove all dust/dirt and loose particles to expose bare concrete roof slab and romoval of rubbish/demolished material out side MD land complete all as specified Note : Demolition should be done by chiselling.

M&L brushing neat cement slurry @ 3 Kgs of cement per Sqm complete all as specified and directed.

M & L for rendering 15 mm thick in CM 1:3 on fair faces of brick work or concrete surfaces on roof finished even and smooth using liquid water proofing compound as per manufacturers instructions Complete all as specified and directed. (Note :- Supply only liquid water proofing compound shall be measured & paid separately).

M&L for PCC 1 : 2 :4 type B0 (using 12.5mm graded stone aggregate) as in levelling padding course over RCC roof surface including rounded or chamferred on edges etc mixed with approved water proofing compound all as per manufacturer'ss instructions on the roof surface to achieve requisite slope all as specified and directed.

Supply only polymer based liquid water proofing compound complete all as specified and directed.

M&L for providing 4 mm thick APP modified memberane over (Accessible) RCC roof with the following specifications :- (a) Cleaning existing surface properly. (b) Apply oil bound bitumen primer @ 0.40 lit/Sqm manufactured by the same agency as that of APP with a density of 0.87 -0.89 Kg/Lit at 25 Degree Centigrade on the prepared dry roof surface. (c) providing and Laying APP modified water proofing membrane reinforced with non wooven polyster matt with physical propertities as under :- (i) Membrane weight >3.6 Kg/Sqm. (ii) Net wooven polyster weight >160 gm/Sqm (iii) Softening point of membrane > 150o C (iv) Joint Tensile strength Longitudiual > 650 Sq Cm at 230o C & Transverse > 450/ Sq cm (v) Tear strength - Longitudual > 300 N & Transverse > 250 N Direction (vi) Elongation > 30 % (vii) Impermeability under water pressure > 3 Kg/Sq cm Note :- APP membrane shall be laid using butane torch by Torch application with minimum 10 cm side overlap and 15 cm end lap. The laying of membrane shall be got done through authorised applicator of manufacturer of membrane. (d) Over the membrance provide 20-25 mm thick machine pressed cement concrete tiles 300mm x300mm over & incl cement screed bed 15mm thick in CM 1:4 set and jointed, pointed in neat cement slurry with grey cement complete all as specified and directed".

M&L for providing 4 mm thick APP modified memberane in repairs including removing old treatment over (Inaccessible) RCC roof with the following specifiations :- (a) Cleaning existing surface properly. (b) Apply oil bound bitumen primer @ 0.40 lit/Sqm manufactured by the same agency as that of APP with a density of 0.87 -0.89 Kg/Lit at 25 Degree Centigrade on the prepared dry roof surface. (c) Providing and Laying APP modified water proofing membrane reinforced with non wooven polyster matt with physical propertities as under :- (i) Membrane weight >3.6 Kg/Sqm . (ii) Net wooven polyster weight >160 gm/Sqm (iii) Softening point of membrane > 150o C (iv) Joint Tensile strength Longitudiual > 650 Sq Cm at 230o C & Transverse > 450/ Sq cm (v) Tear strength - Longitudual > 300 N & Transverse > 250 N Direction (vi) Elongation > 30 % (vii) Impermeability under water pressure > 3 Kg/Sq cm Note:- APP membrane shall be laid using butane torch by Torch application with minimum 10 cm side overlap and 15 cm end lap. The laying of membrane shall be got done through authorised applicator of manufacturer of membrane. (d) Over the membrance provide a finishing with solar reflective bituminous aluminium paint @ 0.1 Kg/Sqm as prescribed by manufacture of membrane

Removing loose concrete carefully by low impact hammer bracker or manually by chisel and hammer machanisuem including necessary scaffolding and removal of debris out of MD land Complete all as specified and directed. REHABILITATION WORK ITEMS 23 TO 28 Note : 1. Rehabilitation works is to be carried out by the authorised rep / applicator of the manufacturer and will render certificate at the stages to the effect that work / methodology has been executed / adoped as per the prescribed norms. 2. The rate for rehabilitation works includes necessary scaffolding, form work, steel props, and safety works like barricade, safety net, dust net etc as per site requirement.

M&L for applying rust remover on existing reinforcement and before application of protective coating the surface should be wire brush and throughly cleaned for dust complete all as specified and directed. Note : Mode of measurement shall be for the superficial area of concrete scaled only.

M&L for applying of anti Corrosive primer for exposive steel reinforcement complete all as specified and directed. Make : IP Net RB of Krishna Conchem or equivalent.

M&L for providing and applying structural grade EPIBOND-21-LP prior to application of any type of mortar plaster or micro concreting conforming ASTM-C-882-91 (Arizona Slant Shear Test) to ensure bonding between old concrete and new concrete

M&L for building up the profile of structural members using polymer modified mortar upto 20mm thickness including levelling, profiling etc complete all as specified and directed. Note :- Mode of measurement : Superficial area of concrete will be measured.

M&L for building up the profile of structural members using polymer modified mortar upto 40mm thickness including levelling, profiling etc complete all as specified and directed. Note :- Mode of measurement : Superficial area of concrete will be measured.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories)

S&F 160mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to walls etc complete all as specifed and directed.

S&F 110mm bore PVC (SWR) pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to walls etc complete all as specifed and directed.

S&F 75mm bore PVC soil waste pipe pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to wall fixed with MS clamps8mm dia with two nuts wall nails etc including taking down of any type complete all as specifed and directed.

S&F 160mm dia PVC bend any radius with or with out access doors etc, completed as specified and directed.

S&F 110mm dia PVC bend any radius with or with out access doors etc, completed as specified and directed.

S & F 110 mm bore PVC (SWR) Branch piece, single (single Y) equal or unequal of any radius with access door complete all as specified and as directed.

S & F 75 mm bore PVC (SWR) Branch piece, single (single Y) equal or unequal of any radius with access door complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) Vent Cowl complete all as specified and as directed.

M & L for Bands, straps, supports, hold fasts or stays for wooden post, two or three way and securing complete conforming to Fe-290 Gde E-165 complete all as specified and directed.

M & L for Resecuring or easing & adjusting without taking down door shutter of any description exc 1.00 but n exc 2.00 Sqm each complete all as specified and directed.

Taking down door / window shutter of any description exc 1.00 but n exc 2.00 sqm each and refixing in the same opening after easing, adjusting & renewal of unserviceable screws etc complete all as specified and directed.

Supply & fixing in repairs aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed

Demolition of cement concrete unreinforced of any description and in any position and removal of debris outside MD land complete all as specified and directed.

M&L for providing stages wise waterproofing treatment to sunken portion surface area bottom & sides of toilets as under:- Stage 1: Providing 15 mm thick plaster in CM 1:3 mixed with integral water proofing chemical of STP Ltd in the proportion /quantity all as per manufactures instructions complete all as specified and as directed. Stage : Primer - Mix Tarfelt LM with water in ratio 1:1 @ 250 gms/sqm and apply the primer on the plaster surfaces complete all as specified and as directed. Stage 3 : Application of 1 st coat of Tarfelt LM of STP Ltd without dilution with water@1kg/sqm by brush all as per manufactures instructions complete all as specified and as directed. Stage 4: Laying 50 GSM fyber glass cloth over the 1st coat while the coated surface is still tacky complete all as specified and as directed. Stage 5: After 6 to 7 hours interval apply second coat i.e final coat of Tarfelt LM without dilution with water of STP Ltd by brush as per manufactures instructions.@1kg /Sqm complete all as specified and as directed. Stage 6: Providing 10mm thick protective plaster in CM 1:3 mixed with STP NO -1 @ 250ml/50kg cement all as manufactures instructions complete all as specified and as directed.

M&L for cement concrete Type E2 1:5:10 using 40 mm graded aggregate or brick bats as in lean concrete complete all as specified and as directed.

S&F in repairs vitreous China squatting pan, 'orrisa' pattern WC of size 580 x 440 mm white with integral foot rest (excluding flushing cistern and flush pipe but including 'P' or 'S' trap and provision of lime concrete bedding complete all as specified and directed.

S&F in repairs Vitreous China wash down water closet Pan (Padestal Pattern) white with seat cover and fixing complete all as specified and directed.

M&L WC connector 110 mm PVC SWR for WC complete all as specified and directed.

M&L PVC valveless, syphonic action type, 10 ltrs cap flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe 32mm dia and fixed in repairs complete all as specified and directed.

M&L connector PVC 450mm long complete all as specified and directed.

Dismantling floor, hearth or wall tiling any description and thickness including cement mortar bedding (but not backing) and removing rubbish off the premises.

M&L PCC 30mm thick type B0, 1 : 2 : 4 (12.5mm graded aggregate) in sub flooring complete all as specified and directed.

M&L non-skid coloured joint free ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry over and including provision of bedding layer 15 mm thick in CM 1 : 4 complete all as specified and directed.

M&L glazed ceramic jointless coloured tiles in vertical surface 350x250x7mm / 450 x 350 x 7mm set and jointed in neat cement slurry over and including provision of bedding layer 10mm thick in CM 1 : 3 complete all as specified and directed.

M&L non-skid coloured joint free ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 Sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry over and including provision of bedding layer 15 mm thick in CM 1 : 4 complete all as specified and directed.

S&F PVC cabinet mirror in repairs of size 600X450 mm complete all as specfied and directed.

Demolition of cement concrete in ground floor / paving not exceeding 15Cm thick below or above GL unreinforced complete all as specified .

M&L for cement concrete type C-1, 1:3:6 (20 mm graded aggregate) 75 mm thick as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

M&L bitumastic filling the joint of 10mm wide and 75 mm depth comprising of one part of heated bitumen blown grade (85/25) any penetration and 2 part of sand by weight all as specified and directed.

Demolition of Reincorced concrete in chajjas and similar suspended, slab facia drop etc work complete all as specified and directed.

M&L RCC 1 : 2 : 4 type B1 Nominal mix (using 20mm graded stone aggregate) in chajjas complete all as specified and directed .

M&L RCC 1 : 2 : 4 type B1 Nominal mix (using 20mm graded stone aggregate) in fascias, louvres, parapets and the like complete all as specified and directed .

S&F TMT bars 10mm dia & over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L form work for soffit and sides of chajjas, troughs and similar items including edges rough finished surface of concrete flat complete all as specified and directed.

M&L form work to fins, louvers, fascia rough finished surface of concrete flat complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including similar pattern roof covering complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs / blankets any thickness including cover fillets complete all as specified.

M&L Hangers 6 mm dia G I (upto 1200 mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion hold fasterners 12.5 mm dia 40 mm long complete all as specified.

M&L anodised aluminium snap grid frame work for false ceiling of grid size 605 x 605mm complete all as specified and directed.

M&L Non asbestos fibre cement building boards 4mm thick fixed / inserted to GI frame work complete all as specified and directed.

M&L Rotational moulded polyethylene water storage tanks (Cylindrical verticval with closed top) hoisted & fixed in position in repairs incl dismantling all as specified of 500 ltrs capacity complete all as specified and directed..

M&L Rotational moulded polyethylene water storage tanks (Cylindrical verticval with closed top) hoisted & fixed in position in repairs all as specified of 1000 ltrs capacity complete all as specified and directed..

M&L Rotational moulded polyethylene water storage tanks (Cylindrical verticval with closed top) hoisted & fixed in position in repairs all as specified of 2000 ltrs capacity complete all as specified and directed..

M&L in repairs Ball valve high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed complete .25mm dia complete all as specified and directed.

M&L Nipple suitable for HDPE water tank (minimum weight 25mm - 65 gms) 25mm bore dia complete all as specified and directed

S&F in repairs Steel rolling shutters 1.25mm thick lath, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated complete gear operated type with bevel gear box and crank handle complete all as specified and as directed.

M&L Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and as directed.

M&L Ball bearing for rolling shutters complete all as specified and directed.

Dismantling of wrought iron or mild steel work in any description and in any position complete all as specified and as directed.

M&L rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates etc conforming to Fe 410-W (Gde-E-250) complete all as specified and directed

M&L roof trusses (framed) trussed, purlins, crange gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde-E-250) complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc (150micron) coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc(150 micron) coating GI based Plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Prepration of new steel surface of any description not exc 60cm in girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for post constn, antitermite treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

M&L for providing and injecting chemical chloropyrphos emulsion conforming to IS-3244(with 20% EC) for post construction antitermite treatment along external wall below concrete or masonry apron @ 2.25 litre per running meter including drilling and plugging note complete all as specified and directed.

M&L for post construction antitermite treatment at point of contact of wood work by chemical emulsion ( in oil or kerosene based solution) @ 0.5 ltr/hole by drilling 6mm dia hole at a downward angle of 45 degree at 150 mm centre to cetre and sealing the same complete all as specified and directed.

M&L Two coat of aluminium paint over a coat of alumimium red oxide primer to new steel surface including preparation complete all as specified and directed.

Resecuring or easing, greasing & adjusting without taking down door shutter or rolling shutter of any description exc 2.00 Sqm each including replacement of unserviceable lever, lock, handle, covering etc as required for smooth operation complete all as specified and directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and as directed.

M&L Solid PVC color coated Wall Panel Lining consisting of 5mm thick inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and as directed.

M&L 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and as directed.

S&F of Aluminium composite panel (ACP) of 4mm thick sheet coated mirror glossy finish/ Natural wood finish of approved colour, pattern & design & as required shape like rectangular, trapezoidal or tapered curved shape (colour, shade, texture as per sample kept in GE office) with Poly Vinylidene Fluoride (PVDF) of flat panel that consist of two thin aluminium sheets (0.5mm thick) bonded to a non-aluminium core of flat sandwich panel is a structure of three layer aluminium core bonded between two sheets of required size fixed with heavy duty screws on aluminium chanel rectangular section of size 38mm X 25mm thickness 2.5mm for vertical & horizontal frame work or equivalant section with respect to weight, and used for external cladding or facades, partition, false ceiling, signage, etc. The joints to be filled with silicon seelant of translucent, white or black in colour with the help of portable punch machine work pneumatically after cutting the carners and edges. A protective film on ACP is removed after installation complete all as specified and directed

S&F in repairs, 1mm thick, stainless steel plate rack of size 120cm x 90cm x 18cm complete all as specified and directed.

Taking up or down steel tubing and connections with15mm bore complete all as specified and directed.

Taking up or down steel tubing and connections with20mm bore complete all as specified and directed.

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors with 15mm bore complete all as specified and directed.

S&F steel water tubes, medium grade, galvanized, with all fittings and fixed to walls and ceilings or laid in floors with 20mm bore complete all as specified and directed.

S&F in repairs, bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule of 15mm bore complete all as specified and directed.

S&F in repairs stop valves,fancy type chromium plated for iron pipe or for unions and fixed to 15mm bore pipe, equivalent complete all as specified and directed.

M&L for Demolition of cement concrete any face internal /external unreinforced of any type any level and at any position Ensure that structure is at least 3 days old, Bonding Agent Bond coat with a mixing ratio of 1:2 (one part of ShaliCrete® and two parts of cement). The applied bonding agent should be in tacky condition before topping. Repair Mortar Bond coat with a mixing ratio of 1:2 (one part of ShaliCrete® and two parts of cement) including 10mm Repair Mortar with a mixing ratio of 1:2:4 (one part of ShaliCrete®, two parts of cement and five part of sand) applied in specified area.• After the application of Repair Mortar to keep the surface moist for 12 - 24hrs and including necessary scaffolding complete all as specified and as directed cement complete all as specified Note : Shali Crete (Acrylic polymer Coating) shall be measured & paid seperately.

Supply only Shali Crete (Acrylic polymer Coating) water proofing compound complete all as specified and directed.

M&L for Mirror polishing on old marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete all as specified and directed.

M&L Machine cut kota stone slab 20-25mm thick over cement screed base and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over in floors over incl 20 mm thick screed bed in cement mortar 1:4 over including finishing even and fair complete all as specified.

Taking down chowkats of frames with shutters (without taking off shutters from frames) area not exceeding 1.50 Sqm each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damages to jambs , walls for taking out hold fast shall be finished idetical to existing finish without any extra cost of Govt) all as specified and directed.

S&F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, in opening as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site complete all as specified and directed

S&F 150 mm long aluminium bow handles cast type anodised complete all as specified and directed.

S&F 200 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F butt hinges med weight cold rolled MS, size 100 mm complete all as specified and directed.

M&L for cutting chases for concealed water tubing not exc 10cm girth, pinning in, making good to facing and pointing in cement mortar 1: 3 complete as per specified and directed.

M&L for casting & reparing of excessively damaged disressed RCC members (exceeding 40mm in thikness) with prebatched, prepached, single component ready to use microconrete form M/s Krishna Conchem (Molith MC) or equivalent of Dr. Fixit as approved by GE at any level ad at any lead or lift as diredted including prefavricated water tight formwork, centering, scaffording, also encliding mixing, laying, leveling, finishing, curing etc as per manufacrure’s specifications complete all as per specified and directed. (Note: Reinforcemtn inly shall be measured and paid separately).

Deduct Credit for Demolished/ Dismantled material Rs. (-) 76445.00 (Minus) as listed in Schedule of Credit Note1: Tenderers will not quote against this item being a tentative amount to be considered to arrive at the 'Contract Sum' Note 2:- The tenderer must keep in mind when quoting rates against items out in multiple store house having height 4 mts to 7 mts. Necessary scaffolding and saftey measures required during execution of work are including in this items.

M/s Qureshi Construction Co

M/S SURAJ A POUL

industrial suppliers

Vishal Builders