REPAIR/ MAINT OF BOUNDARY WALL, GATE FENCING, DRAINS PATH, HARDSTANDING AND OTHER ALLIED SERVICES IN ZONE-I II UNDER AGE B/R-II OF GE (NORTH) MEERUT CANTT

Demolition of cement concrete (Unreinforced) in ground floor and paving n exc 15 cm thick below or above ground level complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 Type C-2 (40mm graded aggregate) as in sub-floor, sub-base, floor and pavings, etc. complete all as specified and directed

M&L Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour (Glossy finish), design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;complete all as specified and directed.

M&L for precast chequered cement concrete tiles of size 300x300x25mm thick, with grey cement and pigment, laid in floors with grey cement and joints filled with grey cement and pigment to match colour of tiles laid over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded, jointed and pointed in any mortar complete all as specified and directed.

M&L for exterior grade, coloured vitrified ceramic designer floor tiles for parking area, paved area, size 400mm x 400mm x 10mm thick, set,jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour/ matrix of tiles laid over and including 15mm thick screed bed or bedding layer in CM 1:6 as in floor etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M& L for exterior grade, coloured ceramic designer wall tiles for external wall surfaces, size 450mm x 300mm x 7mm thick or 600 mm x 300 mm x 7 mm thick, set,jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour/ matrix of tiles laid, over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for Cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L 20mm thick granite (Black) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like laid over 10mm thick rendering in CM 1:4 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Demolition of brick work / stone masonry built in cement mortar in any condition complete all as specified and directed.

M&L for brick work with fly ash old size bricks, straight or curved on plan exceeding 6 cm mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with Sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L for brick work with Sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in CM 1:6 except bricks complete all as specified and directed. Note : Serviceable bricks obtained from ser item no 11 shall be reused.

Taking down cement plaster or cement lime plaster on stone surface/brick surfaces of walls including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick using ready mix plaster bags on other than fare surfaces of brick work in cement mortar 1:4 finished even and smooth complete all as specified and directed.

M&L for rendering 15 mm thick on brick or concrete other than fare surfaces in cement mortar 1:6 complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces and applying two coat of cement base paint over a coat of chalk whiting, on plastered surfaces, prepara-tory to distempering complete all as specified and directed.

M&L for preparation of old plastered/ decorated surface of walls and applying two coat of cement based paint complete all as specified and directed.

M&L for prepration of old steel surfaces of any description not otherwise described over 10cm in width or girth and applying two coat of synthetic enamel complete all as specified and directed.

M&L for complete removal of existing treatment of walls and a coat of 1mm thick wall care complete all as specified and as directed.

M& L for applying Two or more coats of 100% Premium acrylic emulsion paint (Weather proof) on new surfaces of wall having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over surfaces using roller for painting complete all as specified and directed

M& L for applying Two or more coats of 100% Premium acrylic emulsion paint (Weather proof) on old surfaces of wall having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over a coat of 1mm thick wall care putty in patches wherever required complete all as specified and directed

M&L for preparing surfaces plastered or unplastered old decorated surfaces of walls and applying two coat of white wash, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Demolition of reinforced cement concrete of any type complete all as specified and directed.

M&L Reinforced cement concrete type B1 (1:2:4) using 20mm graded aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L Reinforced cement concrete type B1 (1:2:4) using 20mm graded aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for column walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilaster and buttresses complete all as specified and directed.

Formwork for rough finished surfaces to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beam and similar work; vertical or to batter complete all as specified and directed.

Formwork for rough finished surfaces square, rectangular or polygonal to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

Reinforcement TMT Steel bars of grade Fe-500/Fe-500 D of 10mm dia and over, cut to length, bent to shape required, incl cranking,bending , spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip complete all as specified and directed.

Reinforcement TMT Steel bars of grade Fe-500/Fe-500 D of 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, incl cranking,bending , spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip complete all as specified and directed.

Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion and making good disturbed ground complete all as specified and as directed.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling fencing wire mesh, any type complete all as specified and directed.

M&L for PCC 1:3:6, type C-2, using 40mm graded stone aggregate as in foundations, fillings, Mass concrete, footings etc complete all as specified and directed.

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for preparation of newly steel and iron surface exceedding 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zink chrome primer complete all as specified and directed.

Supply only chain link MS Galvanised fencing , any size or type complete all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and directed.

S&F mild steel bolts n exc 12 mm dia purpose made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexogonal or square exc 30 cm long complete all as specified and directed.

S&F Mild steel round bars 10 mm dia and over, cut ot length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips. (Fe-410-W) (Gde.E-250) quality-A or Fe 290 (Gde -E-165)complete all as specified and directed.

S&F in repairs Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

S&F in repairs concertina coil fencing with punched tape concertina coil 600mm dia, 6 metre length, having 50 Nos rounds per 6 metre length, 125 to 127 Clips, spring core wire (2.5 mm thick) of high tensile strength of 165kg/sq.mm with tape (0.52mm thick), weight of each concertina coil not less than 8.4 Kg and fixing the same on existing Y-shaped angle iron, stud tied with G.I. staples and G.I.clips to retain horizontal, including necessary bolts, complete all as specified and directed.

S&F in repairs rolled mild steel plate girder or single stanchions built of one beam or channel section with flange plate, caps, bases, spices, angle bracket, cleats and other connection Fe-290 (Gde 165) as specified to be prepared for hanging or sliding with and including either hooks or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and handing also fastening and fixing complete all as specified and directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or othercovering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering), including running rails and guides or hanging, also fastening and fixing complete (Fe-410-W(Gde-E-250) quality-B) complete all as specifeid and directed

S&F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde-E-165, for portions framed and hund as gates including pintle hinges, stops hand made sliding bolts etc. for ornamental and intricate designcomplete all as specified and directed.

S&F in repairs factory made precast cement concrete type B0, 1:2:4 ( 12.50 mm graded stone aggregate) louvres and jallies, 35 mm thick (measured solid), including all mouldings but excluding frame work, set in cement mortar 1:4 complete all as specified and directed.

Formwork for rough finished surfaces to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc also splays between floors and beams, etc. complete all as specified and directed.

M&L Reinforced cement concrete type B1 (1:2:4) using 20mm graded aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and directed.

M&L for Rendering 15mm thick in CM 1:4 on brick concrete on fair surfaces complete all as specified and directed.

M&L for Precast RCC 1:2:4, Type B–1 using 20mm graded stone aggregate as in landings, cover slabs [for manholes etc], chullah hoods, Chajjas, water troughs, mangers, Shelves and similar articles with plain faces including formwork, set in cement mortar 1:4 complete all as specified and as directed.

M&L for PCC 1:3:6, Type C–1, using 20 mm graded stone aggregate as in coping including necessary formwork, weathering, slightly rounded or chamfered angles complete all as specified and directed.

M&L for PCC 1:3:6 type C2 (using 20mm gradedgraded crushed stone aggregate) as in surface channel and drains complete all as specified and directed.

Extra for forming fair finished drains or channels upto 30cm inner girth in cement concrete, using extra cement, incl forms, moulds mitred/stopped ends etc complete all as specified and directed

Please Enable Macros to View BoQ information