864/WS-38/2021-22

Amount

M&L for excavation in trenches in hard/dense soil not exc 1.5 mtr wide and not exc 1.5 mtr in depth for laying of cables/errection of pole etc, complete all as specified and directed.

M&L for returning, filling in trenches incl spreading leveling watering and well ramming in layers with hard/dense soil not exc 25 cm thick in each layer, complete all as specified and directed.

M&L for removing excavated soil to a distance not exc 1.5 mtr above the starting point, complete all as specified and directed.

M&L for sand cushioning with a layer of river sand under and above the cable, complete all as specified and directed. Note : Punned thickness shall be measured & paid.

S&L common burnt sub class 'B' designations 75 bricks for cable protection, complete all as specified and directed.

S&L XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armouned power cables (heavy duty) with aluminium conductor, 1100 volts grade, cross sectional area 35 Sqmm, 3.5 core laid in trenches, complete all as specified and directed. .

S&F GI pipe light grade 50 mm dia in trenches for cable protection/on pole/on wall, complete all as specified and directed.

S&F 16Mtr high mast galvanised steel tubular structure with grade 5355 as per BS EN 10025 for shaft and gussets and grade Fe-410 as per IS-2062 for flange and door stiffness contraction in two section longitudinal and welded in one section with thickness of sheet 3mm section, top dia 150mm, bottom dia 340mm with lightening protection arrangement, aviation obstructions light (2 x 100W GLS Type with lamp) and accessories and including necessary excavation, earth work, returning filling, removal of soil from site, PCC foundation, base plate, Anchor plate and No of bolts required all as per manufacturer design and instruction. So as to have proper functioning of high mast light and with the following accesseries:- Make:-Surya/Crompton Greaves/Bajaj/Philips. (i) Lantern carriage ring: As per recommendation of manufacturer. (ii) LED Flood light fitting suitable for 180W capacity comprising of die cast aluminium housing, heat resistant toughened glass, specially designed pre-anodized aluminium reflector to achieve a symmetrical optics, stainless steel toggles, powder quoted MS cradle for mounting, EPDM rubber gasket, unsheathed, multistranded copper cable 1.5 sqmm internal wiring, 15 Amp main terminal suitable for terminating 2.5 sqmm conductor, MS zinc plated and passivated hardware, 1 No earthing suitable for 14 SWG earthing conductor E-40, porcelain lamp holder, open construction copper ballast and all other accessories complete in all respects. Make of flood light shall be same as that of manufacturer of High mast light. Total qty-8 to 9 Nos. (iii) LED Flood light fitting 180W suitable for said fitting-9 Nos Make: Surya/Crompton Greaves/Bajaj/Phillips. (iv) Winch double drum type having operating speed and gear ratio as per manufacturer design working manually / electrically with stainless steel wire rope 6mm dia two point suspension system all as per manufacturer design-1 No. (v) Copper conductor cable PVC sheathed 1100V grade of size 2.5 sqmm PVC insulated from electrical box for 09 fittings each Job-01 Job. (vi) Push button control complete all as specified. Note :- LED 180 W flood light fittings shall deemed to be included in the quoted rate.

M&L for earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of earth plate at a depth not less than 1.5 mtr below normal ground level using galvanised iron strip 25x4 mm as earth lead up to 7.5 mtr long by means of nuts, bolts, thimbles, check nuts and washers etc made of galvanized iron connected to earthing test point all as shown in electrical plate No 3 of SSR Part-I 2009 and as specified or indicated and testing on completion incl earth work and excavation in any type of soil PCC (1:3:6) type C1 chamber, pre cast slab 40mm thick in cement concrete (1:2:4) type B1 with 8 mm dia MS bars reinforced at 10 cm centre to centre both ways incl funnel with GI watering pipe wire mesh and lugs, incl test point, complete all as specified and directed.

Supply, installation, testing and commissioning of factory made L.T Panel suitable for 415 Volts, 3 Phase 4 Wire, 50 Hz AC Supply System confirming to IS:8623/93, outdoor type floor mounting, weather proof, vermin proof, fully ventilated and fabricated out of MS CRCA sheet of 3.15mm thick having copper bus bar of rating 200 Amps, three phase and one neutral fixed on insulator and bus bar insulated by coloured heat shrinkable sleeves. The panel shall be front and back openable including Powder coating internally and externally the entire steel surfaces. All doors shall be provided with suitable locking arrangements. The size of the outer shell should not be less than 600mm x 500mm x 350mm, mounted on angle iron stand made out of angle iron 40 X 40 X 6 mm and grouted in PCC 1:3:6, including the following control gears:- (a) MCCB, 4 pole, 63 Amps capacity, 16 kA breaking capacity -01 No. (b) MCB 'C' Curve Double Pole 415 Volts 20 Amps rating - 09 Nos (c) Indicating Lamp RYB - 01 Set (d) Astro based digital timer switch - 01 No (e) Contactor ML4, 3ph, of capacity 63 Amps - 01 No

ALCO ENGINEERSPVT LTD

ORISON ENTERPRISES

VEDA INFRASTRUCTURE

Adil Mohammad Dijoo

M/S Khan Hussain & Co.