REPAIRS / MAINTENANCE / REPLACEMENT OF SUB-MAIN WIRING, DBs, EARTHING AND MISC REPAIR TO INTERNAL ELECTRIFICATION, CEILING FAN, EXHAUST FAN UNDER AGE E/M-II IN GE (CENTRAL) KHADKI.

Amount

Taking down and servicing of ceiling Fan 1200/1400 mm sweep , removing of old grease from bearing of ceiling fan and re-filling new grease including replacement of worn out nut, bolts, washers, gaskets grease, cotton waste etc and T&P such as chain pulley block ladders nut bolt/ washer and reassembling the fan complete and hanging on its original/ new position as directed by Engr-in-charge. (a) Fixing only of materials supplied vide item NO 11 to 47 here in below is deemed to be included in this item and will not be measured and paid seperately.

Description all as per item No 1 above but exhaust fan heavy duty, metal body 380/400/450/600 mm sweep. (Height more than 10 mtr.)

Description all as per item No 1 above but Air circulator fan metal body 600 mm sweep NOTE FOR ITEM NO-01 TO 03 a) Quoted rates are deemed to be inclusive of the cost of all materials and labour required for dismantling and assembling of equipment in whole as a part there of and cost of minor spares and material required such as grease,nut bolts,washers,clamp,cable gland,supporting clamp, insulation tapes etc b) Major defects such as motor rewinding, replacment of faulty bearings, condensor does not includes in this cost. In case of major problems beyond the scope of contract the same has to intimate to the department within 48 hours. c) The workers employed by the contractor will report to the concerned AGE/JE E/M every day. d) The rate quoted by the contractor is deemed to be inclusive of the cost of dismantling/taking down however cost of Fixing of the items will be mesured and paid under relevant items of schedule. e) The quoted rate include the cleaning of ceiling/exahust/air circulator fan and APFC panels of any capacity. f) Quoted rate is deemed to be inclusive all the safety equipment and other T & P required for carrying out the repairs / maintence. The contractor has to liase with the department in case of taking of electric shutdown of each machinery and has to make the machinery functional of the carrying out maintenance because maximum fans are installed at the height of more than 10 mtr. g)Maximum fans are installed at the height of more than 10 mtr. Contracrors are advised to see the site before quoting the rates.

M&L opening the body cover of Ceiling Fan 1200 mm sweep and make and cutting the existing worn out winding with out damaging the startar removing the coil insulation and putting new insulation of polyster paper, winding with super enameled copper wire of suitable gauge with correct number of turns of auxillary and main winding and varnishing and backing complete including the soldering new lead of copper wire testing complete including transportation to work shop and back all as directed NOTE :- a) Contractor have to make the arrangement for testing of rewinded fan upto 24hrs at Complaint cell of AGE E/M-II (C) Kirkee and in case of failure to above said testing a penalty of Rs 200/- per fan is deducted from contractors due and rewinding of same once again is bonded. b) Fan should be return to MES yard after rewinding within 10 day from the date of issue otherwise a penalty of RS 10/- per day per fan is deducted from contractor due.

Description all as per item No 4 above but ceiling Fan 1400 mm sweep

Description all as per item No 4 above but Exhaust Fan single phase 250/280/300 mm Sweep

Description all as per item No 4 above but Exhaust Fan single phase380/ 450 mm Sweep

Description all as per item No 4 above but Exhaust Fan single phase 600 mm Sweep

Description all as per item No 4 above but Air circulator Fan single phase 450 mm sweep

Description all as per item No 4 above but Air circulator Fan single phase 600 mm sweep

Supply Only Dimmer Controller 240 volts 50 Hz 400 Watts Suitable for Air circulators all as specified Cat No 38659 Make Anchor Modle Penta or equivalent Cona / Leader / Polycab

Supply only SKF bearings 6201 2Z or equivalent

Supply only SKF bearings 6202 2Z or equivalent

Supply only SKF bearings 6203 2Z or equivalent

Supply only SKF bearings 6204 2Z or equivalent

Supply only SKF bearings 6301 2Z or equivalent

Supply only SKF bearings 6302 2Z or equivalent

Supply only SKF bearings 6303 2Z or equivalent

Supply only Terminal connector - Bakelite

Supply only Bearing support plate

Supply only condenser / capacitor suitable for 440 volts single phase of capacity 2.5 MFD, all as specified. MAKE :- Bajaj/Seimen/ Tibcon/Apco/Sagar,

Description all as per item No 21 but for capacity 3.15 MFD.

Description all as per item No 21 but for capacity 4 MFD

Description all as per item No 21 but for capacity 6 MFD

Description all as per item No 21 but for capacity 10 MFD

Supply only (Brass) gun metal bush suitable for 1200 mm / 1400 mm sweep ceiling fan all as specified & directed by Engr - in - charge

Supply only fan regulator electronic step type for 1200 mm /1400 mm sweep ceiling fan including necessary connection all as specified Cat No 38660 Make Anchor Modle Penta or equivalent Cona / Leder / Polycab

Supply only top and bottom canopy of ceiling fan complete with tightening screws,set of two canopys all as specified and directed .

Supply only fan blade suitable for Ceiling Fan 1200 mm sweep all as directed at site by Engr -in-charge.

Supply only fan blade suitable for Ceiling Fan 1400 mm sweep

Supply only fan blade suitable for Single Phase Exhaust Fan 250/280/300 mm Sweep

Supply only fan blade suitable for Single Phase Exhaust Fan 380/450 mm Sweep

Supply only fan blade suitable for Single Phase Exhaust Fan 600 mm Sweep

Supply only fan blade suitable for Single Phase Air Circulator Fan 450 mm Sweep

Supply only fan blade suitable for Single Phase Air Circulator Fan 600 mm Sweep

Supply only ceiling fan down rod of 15 mm dia GI pipe 1.8 mtr length medium grade with holes for nutbolt , connectors, clamps etc for fixing ceiling fan duly screwed.

Supply only ceiling fan down rod of 15 mm dia GI pipe 0.9 mtr length medium grade with holes for nutbolt , connectors, clamps etc for fixing ceiling fan duly screwed.

Supply only ceiling fan down rod of 15 mm dia GI pipe 0.6 mtr length medium grade with holes for nutbolt , connectors, clamps etc for fixing ceiling fan duly screwed.

Supply only Protection gaurd round shape made out with M S wires Suitable clamps bolts and nut etc complete suitable for old Single Phase Air Circulator Fan 450 mm Sweep of make Usha/AUE/Almonard complete all as specified and directed.

Description all as per item No 39 but for Single Phase Air Circulator Fan 600 mm Sweep

Supply only 1/12 HP fan motor suitable for 280/300 mm exhaust fan of any Make and model or as per site requirement all as specified make CG/Havels/Khaitan or existing make

Supply only 1/2 HP fan motor suitable for 450 mm exhaust fan of any Make and model or as per site requirement all as specified make CG/Havels/Khaitan or existing make

Supply only 1/3 HP fan motor suitable for 600 mm exhaust fan of any Make and model or as per site requirement all as specified make CG/Havels/Khaitan or existing make

Supply only mounting bracket of size 12"/300 mm including necessary clamps bolts and nut etc complete suitable for 1/35 HP exhaust fan motor as per existing shape /modle complete all as specified and as directed.

Supply only mounting bracket of size 18"/450 mm including necessary clamps bolts and nut etc complete suitable for 1/12 HP exhaust fan motor as per existing shape /modle complete all as specified and as directed.

Supply only mounting bracket of size 24"/600 mm including necessary clamps bolts and nut etc complete suitable for 1/6 HP exhaust fan motor as per existing shape /modle complete all as specified and as directed.

Supply only fan motor 250 Watt capacity Single phase 240 volt 1400 RPM suitable for 600 mm sweep wall Air Circulator of Almonard Make any model or as per site requirement all as specified and as directed. MAKE :- Usha/AUE/Almonard

Material and labour for point wiring complete with 1.5 sq.mm single core PVC insulated, unsheathed multistranded copper conductor FRLSH cable 1100 Volts grade drawn through and including DLP mini trunking but shall be increased as per actual site requirement , ISI marked including accessories like bends, tees, junction boxes fixed concealed/ recessed in wall or ceiling including 1.5 sq.mm PVC insulated but unsheathed multistranded copper conductor FRLSH cable as earth continuity wire including modular metal flush box with white/coloured top cover plate and frame of required modules for mounting of modular switches, sockets,bell push and fan regulators complete including dismantling taking down old unserviceable wiring and making good to disturbed surfaces all as specified and as directed for light/fan/exhaust fan point controlled by one switch. MAKE of cable :- Havells/ Finolex/Polycab

Description all as per Srl item No 48 above but point wiring for 5 pin switch socket outlet 5 Amps on independent board controlled by one switch.

Description all as per Srl item No 48 above but point wiring for 5 pin switch socket outlet 5 Amps on same board controlled by one switch.

M&L for point wiring in PVC conduit of suitable size but not less than 20mm including all fittings such as elbow, bends, junction boxes, saddles, etc. on surface with and including ISI marked two runs of PVC insulated unsheathed multistranded copper conductor cable (FRLSH) 1.5 sqmm nominal cross sectional area, 1100 volts grade and including one run of 1.5 sqmm (green colour) ISI marked PVC insulated unsheathed multistranded (FRLSH) copper conductor cable as earth wire to be terminated in and incl PVC rectangular block of suitable size for mounting, switches, sockets, fan regulator etc. with 3 mm thick plastic laminated sheet cover for one light/fan/exhaust fan controlled by one switch including making good the disturbed wall and painting the same with matching to existing wall all as specified and directed by Engineer in charge.

Description all as per Srl item No 51 above but 5 pin switch socket outlet 5 Amps on independent board controlled by one switch.

Description all as per Srl item No 51 above but 5 pin switch socket outlet 5 Amps on same board controlled by one switch.

Material and labour for point wiring complete as specified with 1100 V grade 4 Sqmm single core PVC insulated unsheathed multistranded copper conductor cable FR grade, conforming to relevant IS drawn through and including DLP Mini Trunking with all accessories fixed on surfaces of wall, ceiling, incl PVC rectangular block of suitable size for mounting, switches, sockets, fan regulator etc. with 3 mm thick plastic laminated sheet cover including 4 Sqmm single core PVC insulated and unsheathed copper conductor cable FR grade as earth continuity wire connected to common earth and earth dolly including testing complete all as specified and directed by Engr-in-Charge for one 6 pin switch socket outlet 15 Amps/AC Point on independent board controlled by one switch.

Description all as per Srl item No 54 above but for for one 6 pin switch socket outlet 15 Amps/AC Point on independent board controlled by one switch in PVC conduit.

Dismantling and Taking out old unserviceable copper/aluminium sub main wiring/Unarmoured cable (used as Sub main wiring) from any height of any Size and Core with all connecting accessories incld. conduit or casing caping and incld. making good to the disturbed wall and painting the same with matching paint as of existing wall including material all as specified and directed by Engineer in charge.

Material and Labour for Sub main wiring at any height with 2 single core PVC insulated, multi stranded copper conductor cable (FRLSH), unsheathed, 1.5 sqmm, 1100 volt grade conforming to IS drawn through and including New 20 mm PVC conduit and including one single core PVC insulated multi stranded unsheathed copper conductor cable, 1.5 sqmm,, FRLSH green in colour as continuous earth wire including all accessories and fixing arrengements, supporting clamps, bends, sockets and connecting items etc. all as specified and directed.

Description all as per Srl item No 57 above but with and including PVC casing & capping.

Material and Labour for Sub main wiring at any height with 2 single core PVC insulated, multi stranded copper conductor cable (FRLSH), unsheathed, 2.5 sqmm, 1100 volt grade conforming to IS drawn through and including New 20 mm PVC conduit and including one single core PVC insulated multi stranded unsheathed copper conductor cable, 2.5 sqmm,, FRLSH green in colour as continuous earth wire including all accessories and fixing arrengements, supporting clamps, bends, sockets and connecting items etc. all as specified and directed.

Description all as per Srl item No 59 above but drawn through and including PVC casing & capping.

Material and labour for sub main wiring at any height and surface with and including two single core PVC insulated multi stranded copper conductor cable, conforming to IS, FRLSH type, 4.0 Sqmm, 1100 volts grade, drawn through and including New PVC conduit 20 mm dia including connected accessories and one single core PVC insulated multi stranded unsheathed copper conductor cable, FRLSH type, 4.0 sqmm, 1100 Volts grade,,green in colour as earth contuinity wire all as specified and directed by Engineer in charge.

Description all as per Srl item No 61 above but drawn through and including PVC casing & capping..

Material and labour for Sub main wiring at any height and surface with and including two single core PVC insulated multi stranded copper conductor cable, conforming to IS, FRLSH type, 6.0 Sqmm, 1100 volts grade, drawn through and including including New PVC conduit 20 mm dia connected accessories and one single core PVC insulated multi stranded unsheathed copper conductor cable, FRLSH type, 6.0 sqmm, 1100 Volts grade,,green in colour as earth contuinity wire all as specified and directed by Engineer in charge.

Description all as per Srl item No 63 above but drawn through and including PVC casing & capping.

Material and labour for Sub main wiring at any height and surface with and including two single core PVC insulated multi stranded copper conductor cable, conforming to IS, FRLSH type,10.0 Sqmm, 1100 volts grade, drawn through and including including New PVC conduit 20 mm dia connected accessories and one single core PVC insulated multi stranded unsheathed copper conductor cable, FRLSH type,10.0 sqmm, 1100 Volts grade,,green in colour as earth contuinity wire all as specified and directed by Engineer in charge.

Description all as per Srl item No 65 above but drawn through and including PVC casing & capping.

Dismantling and drawing out old unserviceable Sub Main Aluminium/copper wiring from Existing Steel/PVC Conduit of any size and any type from any height with all connecting accessaries (excluding conduit or casing caping) and making good the disturbed wall and painting the same with matching to existing wall including material all as specified and directed by Engineer in charge.

Material and labour sub main wiring at any height including using two single core PVC insulated copper conductor cable (FRLSH) of size 1.5 sqmm 1100 volt grade conforming to IS drawn through existing Steel/ PVC conduit including 1.5 sqmm. PVC multi stranded copper conductor cable (FRLSH) green in colour for continuous earthing all as specified and directed.

Material and labour Sub main wiring at any height including using two single core PVC insulated copper conductor cable (FRLSH) of size 2.5 sqmm 1100 volt grade conforming to IS drawn through existing Steel/ PVC conduit including 2.5 sqmm. PVC multi stranded copper conductor cable (FRLSH) green in colour for continuous earthing all as specified and directed.

Material and Labour for Sub main wiring at any height with four single core PVC insulated copper conductor cable (FRLSH) of size 6 sqmm 1100 volt grade conforming to IS drawn through Existing Steel / PVC conduit including two single core 6.0 sqmm PVC multi stranded copper conductor cable (FRLSH) green in colour for continuous earthing all as specified and directed. Note for item No 35 to 37) :- (a). Two/Four runs of wiring cable and One/two runs of earth continuity wire shall be measured as one length.

Supply and fix ceiling rose PVC/polycarbonate, isolated body, three terminals, complete all as specified & directed .

Supply and fix switch socket combination 2 in 1, 5 pin, 5 Amp flush type universal.

Supply and fix switch socket combination 2 in 1, 3 pin, 5 & 15 Amp flush type universal.

Supply and fix switch piano flush type single pole, one way 5 Amp.

Dismantling and taking down unserviceable any light fitting from any location/height after disconnecting of electrical connection complete including all connected accessories all as directed by Engr-in-Charge.

Supply and fix LED tube light fitting suitable for and including 1x20 W 4 feet long tube with polycarbonate diffuser complete including connecting up to ceiling rose with twin core twisted flexible copper conductor cable with suitable size & all accessories for fixing on steel trusses / false / normal ceiling all as specified & directed. MAKE :- Crompton Cat part no-Bright Linea CCS-100-20-65-HL2-DP-NWH or equivalent

Supply and fix 36W 2X2 LED recessed mounting light fitting complete including connecting up to ceiling rose with twin core twisted flexible copper conductor cable with suitable size & all accessories for fixing on steel trusses / false / normal ceiling all as specified & directed. MAKE :- Crompton Cat Part no-Polaris Nio-I LCTLRNE-36-FO-CDL or equivalent

Supply and fix CRCA housing box LED Type luminiare suitable for and including 2x20 W 4 feet long complete including tube rod & connecting up to ceiling rose with twin core twisted flexible copper conductor cable with suitable size & all accessories for fixing on steel trusses / false / normal ceiling all as specified & directed. MAKE :- Bajaj Cat Part no-BLRB-DB-218 or equivalent in Havells/Crompton

Supply and fixing at 5 to 9 mtr height-150W Industrial LED Highbay luminaire with 110Lm/W, with complete all accessories having IP 66 degree of protection, power factor >0.95,THD<10%, potted driver, Internal Surge Protection-4KV & External Surge Protection-10KV,LED Source make Cree,Osram including safety chain with i bolt complete all as specified and directed by Engineer-in-Charge.Cat Part No LHB11-100-CDL/60-M make : Crompton or equivalent NOTE :- The quoted rates are deemed to be included the cost of Nut-bolts washars or clamps required to be replaced if old one are found unserviceable.

Removing of old main switch after disconecting the incoming and out going cables and supply and fix MCCB thermal magnetic release four pole 25 KA 63 Amps Make Legrand Cat No 420053 /L&T /ABB with one way metal inclosure Cat No 5078 01 /L&T /ABB and making conections of cables with suitable size nutbolt etc including making good the disturbed suface of wall including material complate all as specified and as directed.

Removing of old main switch after disconecting the incoming and out going cables and supply and fix MCCB thermal magnetic release four pole 25 KA 100 Amps Make Legrand Cat No 420055 /L&T /ABB with one way metal inclosure Cat No 5078 01 /L&T /ABB and making conections of cables with suitable size nutbolt etc including making good the disturbed suface of wall including material complate all as specified and as directed.

Removing of old main switch after disconecting the incoming and out going cables, supply and fix MCCB thermal magnetic release four pole 25 KA 160 Amps Make Legrand Cat No 420057 /L&T /ABB with one way metal inclosure Legrand Cat No 5078 01 /L&T /ABB and making conections of cables with suitable size nuts, bolt etc including making good the disturbed suface of wall complate all as specified and as directed.

Removing of old main switch after disconecting the incoming and out going cables, supply and fix Industrial plug and socket board TP 32 Amps including plug top and MCB "C" curve 10 KA 32 Amps Make Legrand Cat No 5078 18 and 4086 58 /L&T /ABB and making conections of cables with suitable size nuts, bolt etc including making good the disturbed suface of wall complete all as specified and as directed.

Removing of old main switch after disconecting the incoming and out going cables, supply and fix one way metal ednclosure all as per LegrandCat No 5077 93 /L&T/ABB and MCB "C" curve TPN 10 KA 32Amps Legrand Cat No 4086 80 /L&T/ABB and making conections of cables with suitable size nuts, bolt etc. including making good the disturbed suface of wall complate all as specified and as directed.

Supply, fixing, connecting and testing in replacement of industrial earth plug & socket with sheet metal enclosure of IP 44 protection rating, electric driven, single phase including MCB 'C' series SP 20 Amps and supplied with neutral link complete all as specified and as directed.

Supply, fixing, connecting and testing in replacement industrial earth Plug & socket with sheet metal enclosure of IP 44 protection rating, electric driven three phase including MCB 'C' series TP 20 Amps and supplied with neutral link complete all as specified and as directed.

Disconnecting and taking down old distribution Box with MCB/fuse grip TPN/SPN DB 2 Way to 12 Way old type DB including taking out all cable connections of any description and in any position and making good the disturbed surface of walls, to match with the existing surfaces complete all as specified and directed by Engineer in charge.

Supply and fix connecting & testing of VTPN DB of 12 way suitable for MCCB up to 160A as a incomer & SP / TP MCB as a outgoings with IP 43 -IK09 as conforming to IEC 61439-3 & made of high quality CRCA sheet shall have integrated door earthing system, shall have reversible door facility, ergonomic design with rounded corners to protect against damage like bending, peeling of paint hence preventing rusting. DB shall be with Insulated Busbar with withstand capacity of 36kA, shrouded neutral bar, Door earthing, corner Safe. wiresets, shrouded Neutral bar, earth bar & wire ties, all as specified & directed of Make Legrand Cat.No. 5077 48 or equivalent in Schneider/L&T. Note : MCCB , MCB will be measured and paid separately under relevant item of this schedule.

Supply and fix connecting & testing of VTPN DB of 8 way suitable for MCCB up to 160A as a incomer & SP / TP MCB as a outgoings with IP 43 -IK09 as conforming to IEC 61439-3 & made of high quality CRCA sheet shall have integrated door earthing system, shall have reversible door facility, ergonomic design with rounded corners to protect against damages like bending, peeling of paint hence preventing rusting. DB shall be with Insulated Busbar with withstand capacity of 36kA, shrouded neutral bar, Door earthing, corner Safe. wiresets, shrouded Neutral bar, earth bar & wire ties, all as specified & directed of Make Legrand Cat.No. 5077 47 or equivalent in Schneider- Acti-9/ L&T-Exora. NOTE :- MCCB , MCB will be measured and paid separately under relevant item of this schedule.

Supply and fix connecting & testing of VTPN DB of 4 way suitable for MCCB up to 160A as a incomer & SP / TP MCB as a outgoings with IP 43 -IK09 as conforming to IEC 61439-3 & made of high quality CRCA sheet shall have integrated door earthing system, shall have reversible door facility, ergonomic design with rounded corners to protect against damages like bending, peeling of paint hence preventing rusting. DB shall be with Insulated Busbar with withstand capacity of 36kA, shrouded neutral bar, Door earthing, corner Safe. wiresets, shrouded Neutral bar, earth bar & wire ties, all as specified & directed of Make Legrand Cat.No. 5077 45 or equivalent in Schneider- Acti-9/ L&T-Exora. NOTE :- MCCB , MCB will be measured and paid separately under relevant item of this schedule.

Supply and fix connecting & testing SPN DBs of 8 way for using MCBs / MCB isolators suitable for single pole and neutral, with IP 43 -IK09 as conforming to IEC 61439-3 & made of high quality CRCA sheet shall have integrated door earthing system, shall have reversible door facility, ergonomic design with rounded corners to protect against damages like bending, peeling of paint hence preventing rusting. DB shall be with Insulated Busbar with withstand capacity of 10kA, shrouded neutral bar, Door earthing, corner Safe. wiresets, shrouded Neutral bar, earth bar & wire ties, all as specified & directed of Make Legrand Cat.No. 5076 11 orequivalent in Schneider/L&T.

Supply and fix connecting & testing SPN DBs of 12 way for using MCBs / MCB isolators suitable for single pole and neutral, with IP 43 -IK09 as conforming to IEC 61439-3 & made of high quality CRCA sheet shall have integrated door earthing system, shall have reversible door facility, ergonomic design with rounded corners to protect against damages like bending, peeling of paint hence preventing rusting. DB shall be with Insulated Busbar with withstand capacity of 10kA, shrouded neutral bar, Door earthing, corner Safe. wiresets, shrouded Neutral bar, earth bar & wire ties, all as specified & directed of Make Legrand Cat.No. 5076 12 or equivalent in Schneider/L&T.

Supply and fix ceiling fan of 1200 mm sweep 3 star rating including provision of cable from ceiling rose or connector to fan,anchor bolt for fixing of ceiling fan,ceiling fan rod at any height Complete all as specified & directed by Eng-in charge. MAKE :- Bajaj Cat part No. Sabse Tez EE03 251119 or equivalent to Crompton/Havells

Supply and fix exhaust fan (Metal body) AC single phase 230/240 V of size 300 mm sweep with louvres and provn of flexible copper cord from ceiling rose to fan including making hole in wall without making disturbed the good surface Complete all as specified & directed by Eng-in charge. MAKE :- Bajaj Cat part No: Bahar 70001 or equivalent to Crompton/Havells

Supply and fix exhaust fan (Metal body) AC single phase 230/240 V of size 450 mm sweep with louvres and provn of flexible copper cord from ceiling rose to fan including making hole in wall without making disturbed the good surface Complete all as specified & directed by Eng-in charge. MAKE :- Bajaj Cat part No: Supreme Plus 70065 or equivalent to Crompton/Havells

Supply and fix exhaust fan (Metal body) AC single phase 230/240 V of size 600 mm sweep with louvres and provn of flexible copper cord from ceiling rose to fan including making hole in wall without making disturbed the good surface Complete all as specified & directed by Eng-in charge. MAKE :- Bajaj Cat part No: Bahar 70000 or equivalent to Crompton/Havells

Supply and fix wall mounted fan 400mm sweep 230V, AC, SP oscilating swing type with all acceessories and fixing arrengement Complete all as specified & directed by Eng-in charge. MAKE :- Bajaj Cat part No.Neo spectrum Grey 250890 or equivalent

Supply and fix air circulator fan 650mm sweep 230V, AC, SP oscilating swing type with all acceessories and fixing arrengement Complete all as specified & directed by Eng-in charge. MAKE :- Supreme plus Cat part No: 250528 or equivalent

Supply only MCCB FP, 16kA, 63 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, Adjustable short circuit for each phase from 5 - 10 x Ir including Supply Only of spreader Terminals, discnnecting and dismantling old unserviceable MCCB to the complete satisfaction of Engr-in-Charge. MAKE :- legrand cat no-4200 13 or equivalent to ABB/L&T/Seimens

Supply Only MCCB FP, 25kA, 100 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, Adjustable short circuit for each phase from 5 - 10 x Ir including Supply Only of spreader Terminals, discnnecting and dismantling old unserviceable MCCB to the complete satisfaction of Engr-in-Charge. MAKE :- legrand cat no-4200 57 or equivalent to ABB/L&T/Seimens

Supply Only MCCB FP, 25kA, 160 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, Adjustable short circuit for each phase from 5 - 10 x Ir including Supply Onlyof spreader Terminals, discnnecting and dismantling old unserviceable MCCB to the complete satisfaction of Engr-in-Charge. MAKE :- legrand cat no-4200 55 or equivalent to ABB/L&T/Seimens

Supply Only MCCB TP, 25kA, 200 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, Adjustable short circuit for each phase from 5 - 10 x Ir including Supply Only of spreader Terminals, discnnecting and dismantling old unserviceable MCCB to the complete satisfaction of Engr-in-Charge. MAKE :- legrand cat no-4202 08 or equivalent to ABB/L&T/Seimens

Supply Only MCCB TP, 25kA, 250 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, Adjustable short circuit for each phase from 5 - 10 x Ir including Supply Only of spreader Terminals, discnnecting and dismantling old unserviceable MCCB to the complete satisfaction of Engr-in-Charge. MAKE :- legrand cat no-4202 09 or equivalent to ABB/L&T/Seimens

Supply Only MCCB TP, 36kA, 400 AMPS with thermal magnetic release, Ics = 100% Icu, Adjustable Over Load setting: 0.8 -1.0 x In, Adjustable short circuit for each phase from 5 - 10 x Ir including Supply Only of spreader Terminals, discnnecting and dismantling old unserviceable MCCB to the complete satisfaction of Engr-in-Charge. MAKE :- legrand cat no-422007 or equivalent to ABB/L&T/Seimens

Supply and fix MCB 6 to 32 Amps, single pole and neutral, "C" curve 10 kA breaking capacity with integrated label holder, sliding bottom clamp, color coded On/Off indication on dolly complete all as specified and directed. MAKE : - Legrand/ABB/L&T/ Seimens.

Supply and fix MCB 6 to 32 Amps, single pole, 10 kA breaking capacity with integrated label holder, sliding bottom clamp, color coded On/Off indication on dolly, complete all as specified and directed. MAKE :- Legrand/ABB/L&T/ Seimens.

ONKAR ELECTRIC AND GENERAL STORE

M/S SVOJAS ELECTROMECH ENTERPRISES