PROVN OF HARD STANDING, COVERED SHED, COMPOUND WALL, PARKING SHED AND PATHWAY AT MIL STN PANAGARH UNDER GE PANAGARH

Amount

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc or for shafts, wells, cess pits, manholes pier holes tec not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in soft/loose soil, complete all as specified and as directed.

Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level n. exc 1.50 m above the staring point, complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm as in soft/loose soil, complete all as specified and as directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering, complete all as specified and as directed.

M&L for Plain cement concrete 1:4:8 Type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete, complete all as specified and as directed.

M&L for RCC 1:2:4 type B-1 nominal mix using 20 mm graded stone aggregates as in shelves/slabs supported on walls /beams ,foundation ,plinth beam, bases for column, complete all as specified and as directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

All as per item no 07 here-in-before but 6 to 8 mm dia, complete all as specified and as directed.

Use & waste of wooden form work (rough finished) to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (horizontal/sloping), complete all as specified and as directed.

M&L for flyash brick work straight or curved on plan exc 6 m mean radius built in CM 1:6, complete all as specified and as directed.

M&L for Rendering/plastering, 15mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, using WPC, surfaces finished even and smooth without using extra cement ,complete all as specified as directed. (Note: WPC measured separately).

Supply only intergal WPC,complete all as specified as directed. Note: WPC shall be used as per manufacturer instructions

M&L for 40mm thick pre-cast lowers and jallies (measured solid) in cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate including all moulding but excluding frame and set in cement mortar 1:4, complete all as specified and directed by Engr-in-Charge.

M&L for Preparation of new plastered surfaces and applying two coats of cement base paint over a coat of primer ,complete all as specified and as directed.

M&L for cement concrete Type C-2, 1:3:6 (40mm graded stone aggregate) in foundations, filling and mass-concrete,complete all as specified and as directed.

M&L for Pre-cast cement concrete block masonry type C I 1:3:6 using 20 mm graded stone aggregate with solid blocks, exc. 10 cm in width and setting in mortar ,complete all as specified and as directed.

M&L for 150 mm thick cement concrete type C-2, 1:3:6 (40mm graded stone aggregate) as in paving finished even and fair ,complete all as specified and as directed.

M&L for PCC 1:2:4 B-1 (using 20 mm graded stone aggregate) as on copping ,complete all as specified and as directed.

M&L for machine pressed concrete 60 mm thick paver block interlocking tiles of approved size, set, jointed and pointed using with grey cement and pigment in floors, paving etc. ,complete as per manufacturer instructions and direction.

M&L for sand filling under floor or foundation including watering and consolidation,complete all as specified and as directed.

Surface excavation n. exc 30 cm deep soft/loose soil and averaging 15 cm deep and getting out loose/soft soil,complete all as specified and as directed.

Surface excavation n. exc 15 cm deep and site clearance in soft /loose soil ,complete all as specified and as directed.

M&L for sand filling under floor or in foundation including watering and consolidation,complete all as specified and as directed.

M&L for hard core gauge broken bricks n. exc 63 mm, deposited spread and levelled n. exc 15 cm, water and rammed to a true surface,complete all as specified and as directed.

M&L for Providing 100 mm thick PCC 1:4:8 type D-2 (using 40 mm graded aggregate) as in sub base flooring,complete all as specified and as directed.

M&L for Providing 100 mm thick PCC 1:2:4 type B-1 (using 20 mm graded aggregate) as in TOP flooring including finishing cement morter surface even and smooth without using extra cement, complete all as specified and as directed.

M&L for forming 12 mm thick expansion joint filled with pre-formed bituminous filler and top 30 mm primed and sealed with ceiling compound grade `B',complete all as specified and as directed.

M&L for rendering 15mm thick on fain faces of brick work or cemetn concrete surface in CM 1:4 and finished even and smooth with out use extra cement ,complete all as specified and as directed.

S&F Pre - Painted galvanized aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws ,complete all as specified and as directed.

S&F Pre - Painted galvanized aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws ,complete all as specified and as directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 ,complete all as specified and as directed.

M&L for prepration of newly priming surface of steel surface and applying two coat of synthetic enamel paint ,complete all as specified and as directed.

M&L for prepration of newly plastered surface of wall and appling three coat of white wash ,complete all as specified and as directed.

M&L for reinforced cement concrete (nominal mix) type B-1 1:2:4 (20mm graded stone aggregate) in columns, pillars, piers, etc., complete all as specified and as directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter, complete all as specified and as directed.

M&L for formwork for rough finished surface of concrete (flat surface) to sides of pillars, posts, struts, piers, columns, and stanchions, complete all as specified and as directed.

M&L for damp proof course 40mm thk in cement concrete 1:2:4 type B-0 to horizontal or vertical surfaces including necessary form work ,complete all as specified and as directed.

M&L for 75mm PCC 1:3:6 type C2 using 40mm graded stone aggregate as in plinth protection ,foot path and hard standing , complete all as specified and directed.

M&L for forming construction joint 30mm deep X 10mm wide with sealing compound grade A ,complete all as specified and as directed.

M&L for rendering 20 mm thick cement plaster in CM 1:6 on external fair faces of brick/concrete work surfaces finished even and smooth (without using extra cement) including WPC,complete all as specified and as directed. (Note :WPC will be measured and paid separately).

M&L for rendering 5 mm thick in CM 1:6 on fair faces of brick work or concrete wall surfaces & finishing the surfaces fair and even on ceiling ,complete all as specified and as directed.

M&L for preparation of newly steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome, complete all as specified and as directed.

M&L for providing 150 mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base of flooring ,complete all as specified and as directed.

M&L for 75 mm thick PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in floors, pavings etc.,complete all as specified and as directed.

M&L for Soling 150 mm thick (or sub base) with broker boulders or quarried stone, inter stices filled, surface formed and rolled and consolidated to required gradient and camber ,complete all as specified and as directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finish smooth & even without using extra cement ,complete all as specified and as directed.

BABY ENGINEERING ELECTRICAL MECHANICAL STORES

FRIENDS CONSTRUCTION

M/S AJIT KUMAR KONAR AND SUBHAS CHANDRA KONAR

UNITED BUILDERS

SARASWATI ENTERPRISE (INDEX NO CEEC D-81)

Hooghly Construction Co.

Anmol Yash S.D. Construction Pvt. Ltd.