PROVN OF OTM ACCN FOR 15 CORPS DENTAL UNIT BB Cant

Amount

Total Amount of Sch 'A' Part-I (Sec-I) ( Building works) carried forward from pre-priced Schedule.

Sch 'A' Part-I (Sec-II) ((Building work) Note : This schedule is not estimated by MES and the estimated rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Construction of a block of Covered Accn for Type B Veh including Apron, Compressed Air Eqpt Room, MT store , MT Driver rest room, Plant room for CHS & DG set room etc. S/S building of permanent specification complete all as specified and shown on drawings.

Total amount of Sch 'A' Part-I (Sec-III) (PARKING/PAVED AREA) carried forward from pre-priced Schedule.

Total amount of Sch 'A' Part-I (Sec-IV) (Building work Special items) carried forward from pre-priced Schedule.

Sch 'A' Part-I (Sec-V) ((Building work Special items) Note : This schedule is not estimated by MES and the estimated rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

False ceiling khatamband pattern of approved design with ornamental wood work made out of deodar wood including french polishing ( two or more coat) including 12 mm thick BWR plywood complete all as specified and directed.

Venetion blind of 100 mm wide strip for officer complete all as specified and as directed.

Lead lining sheet on wall s/door/window of x-ray room including all fixing arrangement with of paint to match the shade with the existing surface all as directed by Engr-in-charge.

Total amount of Sch 'A' Part-II (Sec-I) (Internal Electrification) carried forward from pre-priced Schedule.

Sch 'A' Part-II (Sec-II) (Internal Electrification) Note : This schedule is not estimated by MES and the estimated rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Supply and fix lamp holder bracket type with LED lamp 7W, PVC/Polycarbonate type with skirt cap suitable for batten fitting, complete all as specified and directed.

Telephone socket RJ 11 with shutter, top connector with suitable size of module for fixing arrangement, complete all as directed. Make: Cat Part NO AHLKHWWOOO of Havells or equivalent make as mentioned in Appendix "E".

LED mirror light fitting with LED lamp, 1 x 10W, 230V, complete with all accessories and including connecting up with three core twisted flexible copper conductor with suoitable size of 230 volts, 50 Hz complete all as specified and as directed.

Supply and fixing of exhaust fan heavy duty AC single phase 230V/240V 50Hz of size, 300mm sweep 1400 rpm and compelte with louvers, shutter and connecting up ceiling rose to connector block of fan including making of holes and grouting of nuts and bolts complete all as specified and as directed. make : Havellsor equivalent make as mentioned in Appendix "E" complete all as specified and directed.

Ceiling fan of size 1200 MM sweep Having (BEE 5 Star rating ) complete and connecting up including provision of with copper standard conductors cables from ceiling rose/ connector to Fan . Make Bajajor equivalent make as mentioned in Appendix "E" complete all as specified and directed.

S&F Aesthetically designed 2x2 LED flat panel provides soft light 18W and glare free symmetrical illumination suitable for recessed mounted fixture for armtrong grid/POP ceiling (with wedge brackets) environment friendly, high performace electronic driver, CRCA powder coated, lumen efficay of > 140 Im/W and viewing angle of 120 degree to ensure batter uniformity, high transmittance polystyrene opal diffuser for glare free symmetric light distribution, powered by an independent isolated SELV output electronic LES driver (SMPS) based constant current supply) with out put short circuit protection, surge protection & other safety tests as per IS-15885 Part-2 Sec 13, colour temperature 5700K compelte with LED lamp and driver. Make: Havells Model No VENUSNEOHE 2x2 PLR 18W LED 8XXS and Driver Code-LSSCRX1781or equivalent make as mentioned in Appendix "E" complete all as specified and directed.

S&F Aesthetically designed 1x1 LED flat panel providesfor surface mounting which provides soft light and glare free symmetrical illimination suitable for 15 W LED lamp, environment friendly , high performance electronic driver, CRCA powder coated , lumen efficacy of > 140 lm/W and viewing angle of 120 degree to ensure better uniformity, High transmittance polystyrene opal diffuser for glare free sysmmetric light distribution, powered by an independent isolated SELV output electronic LED driver (SMPS) based constant current supply) with out put short circuit protection, surge protection & other safety tests as per IS- 15885 Part-2 Sec 13 , colour temperature 5700K complete with LED lamp and driver. Make :- Havells Model No LHEWEIP7PK1W015 (ITEM DESCRIPTION - PLUTOSURFACE1X1PLS15WLED857S and Driver Code- LSGDEDAFCQA1015/ or equivalent make as mentioned in Appendix "E" complete all as specified and directed.

S&F Aesthetically designed 2x2 LED flat panel providesfor surface mounting which provides soft light and glare free symmetrical illimination suitable for 15 W LED lamp, environment friendly , high performance electronic driver, CRCA powder coated , lumen efficacy of > 140 lm/W and viewing angle of 120 degree to ensure better uniformity, High transmittance polystyrene opal diffuser for glare free sysmmetric light distribution, powered by an independent isolated SELV output electronic LED driver (SMPS) based constant current supply) with out put short circuit protection, surge protection & other safety tests as per IS- 15885 Part-2 Sec 13 , colour temperature 5700K complete with LED lamp and driver. Make :- Havells Model No LHEWEIP7PN1W042 (ITEM DESCRIPTION - PLUTOSURFACE2X2PLS42WLED857S and Driver Code- LHGDVDDFCOAL040/ or equivalent make as mentioned in Appendix "E" complete all as specified and directed.

M& L for Endura Linear Neo Surface and wall mounted LED batten, 20 W LED tube (4 ft) having minimum 2000 lumens with epoxy coated white extruded aluminium channel housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver , high efficiency long life LED chips with lumen efficacy of 125 lumen/watt with a viewing angle of 120 degree to ensure better lumen output, milky white special polycarbonate diffuser for glare free efficient light distribution, elegantly designed white coloured ABS end caps, integral electronic (SMPS based constant current supply) with output short circuit protection, surge protection as per IS : 15885 Part-2 (sec 13) , voltage range 140-270V , colour temperature of 5700K>100 lm/W system luminous efficacy and power factor>0.95 and incl 20 W LED tube complete with all accessories. Make: Havells Model No LTEWEBP71N1W020 (Item description ENDURALINEARNEOBS20WLED8665SPCWH) and driver code LSSCRX1763 or equivalent make as mentioned in Appendix "E" complete all as specified and directed.

Supply and fix sheet metal enclosure vertical DB double door VTPN 8 Way (MCCB Incoming + 24 utgoing ) factory made having provision for FP MCCB upto 160 Amp as a incomer, 415 volts, three phase and neutral with 200 Amps rated bus bar. Make : ABB Cat part No. NSYN8690VPXT108 or equivalent make as mentioned in Appendix "E" complete all as specified and directed.

Supply and fix sheet metal enclosure vertical DB double door VTPN 6 Way (MCCB Incoming + 18 Outgoing ) factory made having provision for FP MCCB upto 125 Amp as a incomer, 415 volts, three phase and neutral with 200 Amps rated bus bar. Make : ABB Cat part No NSYN8690VPXT106 or equivalent make as mentioned in Appendix "E" complete all as specified and directed.

Supply and fix sheet metal enclosure vertical DB double door VTPN 4 Way (MCCB Incoming + 12 Outgoing ) factory made having provision for FP MCCB 63 Amp as a incomer, 415 volts, three phase and neutral with 200 Amps rated bus bar. Make : ABB Cat part No NSYN8690VPXT104 or equivalent make as mentioned in Appendix "E" complete all as specified and directed.

S & F MCCB 125 Amps 415 Volts 50 Hz four pole 36 KA with adjustable thermal & fixed magnetic setting Ics= 100 % of Icu incl making connection with existing cable with connection materials like copper strips lugs nuts bolts with sheet metal enclosure suitable for one single MCCB complete all as specified as directed. Make - Havells Model No - IHA13EBF0125 or equivalent make as mentioned in Appendix "E" complete all as specified and directed.

S & F MCCB 100 Amps 415 Volts 50 Hz two pole 15 KA with fixed thermal magnetic releasing system incl making connection with existing cable with connection materials like copper strips lugs nuts bolts with sheet metal enclosure suitable for one single MCCB complete all as specified as directed. Make - ABB/Siemens/Scheinder

S & F MCCB 100 Amps 415 Volts 50 Hz single pole 15 KA with fixed thermal magnetic releasing system incl making connection with existing cable with connection materials like copper strips lugs nuts bolts with sheet metal enclosure suitable for one single MCCB complete all as specified as directed. Make - ABB/Siemens/Scheinder

S & F MCCB 63 Amps 415 Volts 50 Hz SPN 10 KA with fixed thermal magnetic releasing system incl making connection with existing cable with connection materials like copper strips lugs nuts bolts with sheet metal enclosure suitable for one single MCCB complete all as specified as directed. Make - Schneider/ Siemens /ABB

S&F MCCB 40 Amps 230 volts 50Hz SPN 15KA with fixed thermal magnetic releasing system incl making connection with existing cable with connection materials like copper strips lugs nuts bolts with sheet metal enclosure suitable for one single MCCB complete all as specified as directed. Make- Schneider/Siemens/ABB

S&F MCCB 20 Amps 230 volts 50Hz SP 10KA with fixed thermal magnetic releasing system incl making connection with existing cable with connection materials like copper strips lugs nuts bolts with sheet metal enclosure suitable for one single MCCB complete all as specified as directed. Make- Schneider/Siemens/ABB

S&F MCCB 16 Amps 230 volts 50Hz SP 15KA with fixed thermal magnetic releasing system incl making connection with existing cable with connection materials like copper strips lugs nuts bolts with sheet metal enclosure suitable for one single MCCB complete all as specified as directed. Make- Schneider/Siemens/ABB

S & F MCB SP 240 V, 50 Hz, 10 KA , B curve of rating (0.5 - 6 Amp) Make: Scheinder cat Part No - A9N1P06B or equivalent make as mentioned in Appendix "E" complete all as specified and directed.

S & F MCB SP 240 V, 50 Hz, 10 KA , B curve of rating 16 Amp Make: Scheinder cat Part No - A9N1P16B or equivalent make as mentioned in Appendix "E" complete all as specified and directed.

S & F MCB SPN 240 V, 50 Hz, 10 KA , B curve of rating 32 Amp Make: Havells cat Part No - DHMGCSPF006-032 or equivalent make as mentioned in Appendix "E" complete all as specified and directed.

S & F MCB SPN 240 V, 50 Hz, 10 KA , B curve of rating 63 Amp Make: Havells cat Part No - DHMGCSNF063 or equivalent make as mentioned in Appendix "E" complete all as specified and directed.

Supply and fixing TV Socket outlet single with suitable module, complete all as specified and directed. Make- Scheinder Reference No- X4500WH or equivalent make as mentioned in Appendix "E" complete all as specified and directed.

Total amount of Sch 'A' Part-III (SEC-I) (Internal Water supply) carried forward from pre-priced Schedule.

Sch 'A' Part-III (Sec-II) (Internal Water supply) Note : This schedule is not estimated by MES and the estimated rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Angle cock, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule and fixed for bore of pipe 15mm complete all as specified and directed.

Bib taps, cast copper alloy long body, chromium plated with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule and fixed for bore of pipe 15mm complete all as specified and directed.

Material and labour for 15mm dia Elbow control tap Make-ESS or ARL 230009 Hygicia

Total amount of Sch 'A' Part-IV (Sewage Disposal Work) carried forward from pre-priced Schedule.

Total amount of Sch 'A' Part-V (Area Drainage works) carried forward from pre-priced Schedule.

Total amount of Sch 'A' Part-VI (External Water Supply) carried forward from pre-priced Schedule.

Total amount of Sch 'A' Part-VII (Sec-I) (External Electrification) carried forward from pre-priced Schedule.

Sch 'A' Part-VII (Sec-II) (External Electrification) Note : This schedule is not estimated by MES and the estimated rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

LT outdoor cubical door moulded in single piece with enigneering plastic one piece moulding of size 200x200x200mm, shock proof, rust proof, fire regtardant with bus bar of capacity 60 amps 2 strips aluminimum bus bar.

Supply of 70W LED street light luminalre with system lumen output 7700lm and system efficacy of 100lm/W LEX street light shall be made up of Dia cast aluminum housing with black epoxy plyester powder coating for long life. The Luminaire shall be complete P66 protection for optical compartment and control gear compartment. The optical compartment shall be covered with heat resistant toughened glass for safety. The LEDs used in the product shall be reputed make like citizen Japan/Nichia Japan with minimum LEXD efficacy of 160lm /W. LED street light shall use multiLEDs to get sufficient light output from the luminaire. The LED shall be stested with LM80-80 standard with useful life of 50000 Hrs at L70. The LEDs useed in street light shall have CCT of 5700, ANSI Bin warm white with CRI of 70, LEDs used must be testeed as per IEC52471 for photobiological safety of humans. the LED street light shall be of integral type. The input voltage range shall be 120V to 300V. The LED street light luminaire shall have secondary lens optics for optimumlight distribution. The LED Driver shall be made in India. The LED driver shall be of isolated type with constant current constantvoltage topology to ensure optimum driving of LEDs. The LED luminaire shall have minimum 4KV surge protection. The LES street light shall have power factor more thatn 0.95 with THD less than 10% . LED driver output voltage shall be less than SELV limits for safe operation and maintenance. The driver should be fully designed and manufactured in India. The litter of Association with LED manufacturer for LEDs used in the fixture should be submitted to ensure high quality led chips are used in the fixture. LM80 and photobilogical reports should be submitted. Approved wipro catalogue no LR02-781-XXX-57-XX or equivalent of make Philips/GE, Makeing connection with 3 core copper flexible cable of size 23/.0075 all as directed by Engineer-in-charge.

Street light brackets 1.5 mtr long, made out of 40mm dia GI pipe light grade bend to shape weliding etc and fixing on existing LT pole with 40x6 mm flat iron MS clamps including necessary nuts, bolts and washers etc and incl painting two coats with synthetic enamel paint over a coat of red oxide primer after removal of galvanishing with moderate solution complete all as specified and directed.

Supply, installation, testing and commissioning of L.T Panel board CPRI approved suitable for 415 Volts, 3 Phase 4 Wire, 50 Hz AC Supply System confirming to IS:8623/93, with IP-65 protection outdoor type plateform mounted along with factory made type panel weather proof, vermin proof, fully ventilated and fabricated out of MS CRCA sheet of 3.15mm thick having copper bus bar of rating 800 Amps current carrying capacity, three phase and one neutral fixed on insulator and bus bar insulated by coloured heat shrinkable sleeves. The panel shall be front / rear openable and having inner & outer shells. The inner shell duly compartmented for each control gear, including Powder coating internally and externally the entire steel surfaces having thickness not less than 100 micron, including seven tank process . All the cover shall be provided with suitable locking arrangements. The size of the outer shell should not be less than 1200mm x 1400mm x 450mm, mounted on angle iron stand made out of angle size 50 X 50 X 6 mm for mounting of panel 45 cm above ground level grouted in PCC 1:3:6, including the following controls gears and suitable size of Digital volt meter & Digital Amp meter with CTs. (location P2) (A) IN COMING (a) MCCB , 4 pole ,50KA, 400 Amps-01 No (b) Panel mounted multi function energy meter of accuracy CL-1.0 rating - 01 No (c) RYB LED indicating lamp panel mounting type (Set of three) - 01 No.

(B) OUTGOING (a) MCCB 160A , 4P, 25KA, 415 Volt 50 Hz AC with thermal adjustable setting-1 No (b) MCCB 125A , 4P, 25KA, 415 Volt 50 Hz AC with thermal adjustable setting-1 No (c) MCB DP 63A , 10KA, 230 Volt 50 Hz AC (security light) Note:- i. All incomming and out going cable connections to be through proper sized alluminium thimbel and cable gland. ii. Pannel should be mounted on PCC foundation having minimum clearance 45 cm from gound level for connecting incomming and out going cables. cost of PCC platform is included in the quoted rate. Note:- Rate for item No 13.04 and 13.05 shall be quoted at item No 13.04 and no claim what so ever in this regards shall be admissible

Supply, installation, testing and commissioning of L.T Panel board CPRI approved suitable for 415 Volts, 3 Phase 4 Wire, 50 Hz AC Supply System confirming to IS:8623/93, with IP-65 protection outdoor type plateform mounted along with factory made type panel weather proof, vermin proof, fully ventilated and fabricated out of MS CRCA sheet of 3.15mm thick having copper bus bar of rating 400 Amps current carrying capacity, three phase and one neutral fixed on insulator and bus bar insulated by coloured heat shrinkable sleeves. The panel shall be front / rear openable and having inner & outer shells. The inner shell duly compartmented for each control gear, including Powder coating internally and externally the entire steel surfaces having thickness not less than 100 micron, including seven tank process . All the cover shall be provided with suitable locking arrangements. The size of the outer shell should not be less than 1200mm x 1400mm x 450mm, mounted on angle iron stand made out of angle size 50 X 50 X 6 mm for mounting of panel 45 cm above ground level grouted in PCC 1:3:6, including the following controls gears and suitable size of Digital volt meter & Digital Amp meter with CTs. (location P2) (A) IN COMING (a) MCCB 250A , 4P, 36KA, 415 Volt 50 Hz AC with thermal adjustable setting-1 No (incoming) (b) Panel mounted multifunction energy meter of accuracy CL-1.0 rating-01 No (c) RYB LED indicating lamp panel mounting type (Set of three) - 01 No.

(B) OUTGOING (a) MCCB 160A , 4P, 25KA, 415 Volt 50 Hz AC with thermal adjustable setting-1 No (out goings) (CHS Eqpt) (b) MCCB 63A , 4P, 16KA, 415 Volt 50 Hz AC with thermal adjustable setting-2 No (Outgoing) (Second floor and lifts) (c) MCB DP 63A , 10KA, 230 Volt 50 Hz AC - Note:- i. All incomming and out going cable connections to be through proper sized alluminium thimbel and cable gland. ii. Pannel should be mounted on PCC foundation having minimum clearance 45 cm from gound level for connecting incomming and out going cables. cost of PCC platform is included in the quoted rate. Note:- Rate for item No 13.06 and 13.07 shall be quoted at item No 13.06 and no claim what so ever in this regards shall be admissible

Supply, Instln, testing and commissioning of 315 KVA compact substation comprising of the fwg as per the std specs as per IEC 62271/2002 incl all sub clauses with base foundation as per manufacturer recommendation comprising of (A) RING MAIN UNITS: Non extensible 11 KV SF-6 insulated compact ring main unit (RMU) 5 way with short circuit peak making 50 KA and short circuit breaking current 20MA fully arc proof metal enclosed free standing manually operated type SF-6 insulated Load break switches break switches 630 Amps incoming 2 numbers and VCB 200 Amps for outgoing 1 No with self-powered micro based relays and related CT’s complete with manual and mechanical mechanism & degree of protection IP 54 with the fwg components. (a) Manual push button for Emergency Trip. (b) Aluminum bus bar. (c) Front access & button entry of HT cables. (B) TRANSFORMER: Step down transformer, 11 KV/433 Volts (at no load) AC 3 phase 50 HZ 315 KVA capacity, core type, copper wound, on HV & LV oil immerse, naturally cooled, (ON AN), with external cooling tubes delta connected on primary side (HV) and star connected on secondary side (LV) in accordance with vector group DYn-11 with neutral brought out on secondary side (LV side) and having 7 step tapings at +/- 2.5% of each step to be changed by means of hand operated off load tap changer gear. The maximum temperature rise shall not exceed 45 degree Celsius in oil and 55 degree Celsius in HV/LV winding when measured by resistance method after continuous full load run on and ambient temp of 40 degree Celsius. The transformer shall be in accordance with IS-1180 and shall comprise of following:-

(a) Three No porcetain bushing suitable for 11 KV on HV side, complete with copper rods, nuts and washers. (b) One cable box on LT side (secondary side) consisting of four nos porcetain bushing with copper rods, complete with nuts and washers with cable glands suitable for taking out LT supply. (c) Oil conservator with filter type drain valve and oil level gauge. (d) De-hydrating breather with first fill of dehydrating agent silica. (e) Explosive vent, Thermometer pocket on tank cover, oil level gauge, oil rain filter valve, fitting lugs/hooks, oil filling hole with cap/plug with connection solid cast steel detachable rollers. (f) One no 100 mm dia, dial type thermometer, vapor pressure type having range 0-120 degree Celsius with metal guard having maximum perimeter temperature reading indicator with re-setting device. (g) Two earthing terminals on tank cover to facilitate fixing of 50x6mm galvanized iron earth strip for earthing of body. (h) Rating plate and terminal marking plate. (j) Extra bushing for neutral in the LT cable box for providing independent set of earhing for neutral. (k) First filling of new and unused transformer oil, IS-335 marked Oil/power link filtered and tested upto 60 KV dielectric strength at 2.5m air gap between testing electrodes.

(C) LT PANEL:- Panel made out of 2.0mm thick CRCA sheet duly compartmentalized for each control gear, front and back openable single door system lockable/openable by keys from both side having chromium plated 19mm dia fancy locks (02 nos in each compartment) having louvers and vent gasket for natural flow of air. ‘U’ type gasket shall be used to make the panel completely vermin proof and accommodate incomer/outgoing ACB & MCCBs. TPN aluminum bus bar of rating not less than 1.5 times the rated capacity of the incomer ACB. The TPN bus bar shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size ‘F’ class insulators made of non-hygroscopic, non combustible, track resistant high strength FRP/SMC/DMC material having at an interval not more than 500 mm through out the length of the TPN bus bar including the following:- INCOMER:- 01 Nos ACB 4 Pole Amps, 415 Volts, 50KA with micro processor release IPR-2 OUTGOING:-a) MCCB 400 Amps, 4 Pole, 36 KA with thermal magnetic release - 01 No (b) MCCB 250 Amps, 4 Pole, 36 KA with thermal magnetic release-02 No (c) MCCB 63 Amps, 4 Pole, 16 KA with thermal magnetic release-01 No

(d) ENCLOSURE: - (CRCA) powder coated with accessories like lamp, limit switches, wiring, MCB, inner connection of aluminum bus bas from transformer to LT panel, ACB etc. (e) 03 x 1Cx95 sqmm 11 KV HT cable for inter connection in between RMU and transformer unarmoured cable. Make of compact substance: M/s Siemems/M/s ABB/A/s Crompton/M/s Schnider Note: - a) rate shall be quated for item No.13.08. (f) Predespatch inspection at factory shall be done by representative of Accepting Officer. (g) Pre-commissioning of compact substation shall be done by EI/SEI before energizing the system. (h) Test certificate of compact substation shall be produced without which payment shall not be made. (j) PCC works Base foundation required for fixing of compact substation is included in the quoted rate.

Supply and fixing street light control pannel out door type made out of 2mm thick CRC sheet duly powder coated with suitablie for pole mounting type with locking arrangement including follwing acessoies :- (a) MCB DP 63 Amps 10 KA-01 No (incomeer) (b) Astrobased digital time switch-01 (Controle circult) (c) MCB DP 32 Amps 10 KA-02 Nos (out going) (d) on off indicator lamp-02 Nos

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 3.15 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level, connecting to to copper strip of size 20X3 mm as earthing lead by means of bolts, nuts, check nuts and washers of brass after welding of copper strip to earth electrode to the full length of earth plate, GI light grade pipe 40 protection pipe upto test point, 20 mm dia GI watering mm watering pipe with funnel plate and wire mesh, PCC pit 1:3:6 with pit cover of size 30X30 cm made of RCC 1:3:6 with suitable handle, angle iron frame made of angle iron of size 40x40x4 mm, adequate quantity of charcoal dust and salt layers all around the earth plate, removal of surplus soil and returning filling all as required at site including test point made out of steel plate of size 75x75x6 mm fixed to wall all as specified in plate no 3 of SSR part-I and directed by Engineer-in-charge.

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level, connecting to to galvanized iron strip of size 32x6 mm as earthing lead by means of bolts, nuts, check nuts and washers of brass after welding of copper strip to earth electrode to the full length of earth plate, GI light grade pipe 40 protection pipe upto test point, 20 mm dia GI watering mm watering pipe with funnel plate and wire mesh, PCC pit 1:3:6 with pit cover of size 30X30 cm made of RCC 1:3:6 with suitable handle, angle iron frame made of angle iron of size 40x40x4 mm, adequate quantity of charcoal dust and salt layers all around the earth plate, removal of surplus soil and returning filling all as required at site including test point made out of steel plate of size 75x75x6 mm fixed to wall all as specified in plate no 3 of SSR part-I and directed by Engineer-in-charge.

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level, connecting to to galvanized iron wire of size 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of brass after welding of copper strip to earth electrode to the full length of earth plate, GI light grade pipe 15 protection pipe upto test point, 20 mm dia GI watering mm watering pipe with funnel plate and wire mesh, PCC pit 1:3:6 with pit cover of size 30X30 cm made of RCC 1:3:6 with suitable handle, angle iron frame made of angle iron of size 40x40x4 mm, adequate quantity of charcoal dust and salt layers all around the earth plate, removal of surplus soil and returning filling all as required at site including test point made out of steel plate of size 75x75x6 mm fixed to wall all as specified in plate no 3 of SSR part-I and directed by Engineer-in-charge.

Total amount of Sch 'A' Part-VIII (Road/Path/Culvert/)carried forward from pre-priced Schedule.

Total amount of Sch 'A' Part-IX (Fire Fighting System) carried forward from pre-priced Schedule.

Total amount of Sch 'A' Part-X (Sec-I) (Lightening Protetion) carried forward from pre-priced Schedule.

Sch 'A' Part-X (Sec-II) (Lightening Protetion) Note : This schedule is not estimated by MES and the estimated rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level, connecting to to galvanized iron strip of size 32x6 mm as earthing lead by means of bolts, nuts, check nuts and washers of brass after welding of copper strip to earth electrode to the full length of earth plate, GI light grade pipe 40 protection pipe upto test point, 20 mm dia GI watering mm watering pipe with funnel plate and wire mesh, PCC pit 1:3:6 with pit cover of size 30X30 cm made of RCC 1:3:6 with suitable handle, angle iron frame made of angle iron of size 40x40x4 mm, adequate quantity of charcoal dust and salt layers all around the earth plate, removal of surplus soil and returning filling all as required at site including test point made out of steel plate of size 75x75x6 mm fixed to wall all as specified in plate no 3 of SSR part-I and directed by Engineer-in-charge.

Sch 'A' Part-XI (Stand by DG Set work) Note : This schedule is not estimated by MES and the estimated rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Supply, installation, testing and commissioning of silent type diesel engine driven generating set with canopy and acoustic enclosure as per guide line issued by CPCB and Environment Act (415 volts,, AC supply 3 phase 50 Hz four wire complete with panel for automatic starting omn main failure control suitable for giving an output of 200 KVA (160 KW after considering derating factor confirming to IS- 10001/10002 and Alternator as per IS- 13364 complete at 1610 meter altitude above mean sea level and capacity of operating between temperature range -15 degree C to +35 degree at Srinagar area of J & K) and alternator of suitable capacity coupled with each other and capable of taking 10% over load for one hour on every 12 hours as per BS-5514/649 with flexible coupling mounted on common base plate on anti-vibration pads on foundation as recommended by manufacture. The DG set shall comprising of electric starter motor with batteries, turbocharger, water cooled and comprising all standard fittings/ fixtures and all piping etc water cooled/ coolant with radiator complete with in built tank of capacity as per manufacturers specification all as specified and comprising following :-

(A) DIESEL DRIVEN ENGINE :- Developing a net rated output of minimum 402 BHP or next higher capacity suitably matched with alternator to give a net rated output of 200 KVA. The engine should be capable of delivering the required output at 1500 rpm as per BIS 649 under NTP condition with a provision of 10% overload for one hour in every twelve hour and interalia with the following accessories and all as specified :- (i) Fly wheel to suit flexible coupling and fly wheel housing. (ii) Air cleaner complete as per manufacturer specification. (iii) Fuel injection rotary nozzle pump. (iv) Electronic Governor (v) Oil filter and mounting (vi) Flexible coupling with guard nuts and bolts. (vii) Fuel filter with mounting. (viii) Lubricating oil pump and oil cooler. (ix) Starter motor as per manufacturers design. (x) Lubricating oil cooler. (xi) Exhaust silencer, industrial type with exhaust pipe of length, beyond impeller from wall from DG set room. (xii) Drip Tray. (xiii) Battery charger of suitable capacity fitted with transformer/ rectifier unit DC ammeter/ OFF / trickle/Boost switch, DC voltmeter and other standard fitting hour running meter, KWH meter etc. (xiv) 02 Nos maintenance free battery 180 AH, 12 Volt. (xv) Cold start kit.

(B) ALTERNATOR: - The above engine will be coupled through flexible coupling on an indigenous alternator mounted on a strong steel fabricated common base frame suitable for mounting in an acoustic enclosure. The alternator will be 3 phase 50 Hz 1500 RPM self-regulating self-exciting type and generating 200 KVA output at 0.8 power factor 4 wire 415 Volt AC supply under NTP condition with a provn of 10% overload for 1 Hr in every 12 Hrs running at 1500 RPM, the alternator shall be screen protected and fitted with shield ball/ roller bearing conforming to BS 2613/IS 4722. (C) MANUAL CONTROL PANEL: - The control panel body will be fabricated out of 16 SWG MS Sheet. Panel will be suitable for canopy mounting, indoor installation, dust & vermin proof, copper control cable of suitable size is used. Cables are ferruled for proper maintenance/ checking/ wiring of panel. Detachable cable gland plates are provided. The panel will be equipped as follows :- (a) One No Moulded case circuit breaker of suitable capacity. (b) Aluminium Bus bars suitable capacity provided with termination. (c) 03 Nos current transformers of suitable ratio. (d) One set of instrument MCB’s. (e) Microprocessor protections with display and indications of Electrical and Mechanical parameters as per manufacturers design and specifications. (D) FOUNDATION : - PCC 1:2:4 foundation for DG set of suitable size compelte all as per site requirement.

NOTE :- (a) The complete Generating set include Engine/ Alternator shall be factory assembled by manufacturer or its authorized dealer as approved for assembling of the DG set. Make of Assembler shall be:- (i) M/s Bhaskar power Projects. (ii) M/s Green Field Enterprises. (iii) M/s IEC Ltd. (iv) M/s Sudhir Gensets. Note:- Rate for item No 19.01 to 19.04 shall be quoted at item No 19.01 and no claim what so ever in this regards shall be admissible

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level, connecting to to galvanized iron strip of size 32x6 mm as earthing lead by means of bolts, nuts, check nuts and washers of brass after welding of copper strip to earth electrode to the full length of earth plate, GI light grade pipe 40 protection pipe upto test point, 20 mm dia GI watering mm watering pipe with funnel plate and wire mesh, PCC pit 1:3:6 with pit cover of size 30X30 cm made of RCC 1:3:6 with suitable handle, angle iron frame made of angle iron of size 40x40x4 mm, adequate quantity of charcoal dust and salt layers all around the earth plate, removal of surplus soil and returning filling all as required at site including test point made out of steel plate of size 75x75x6 mm fixed to wall all as specified in plate no 3 of SSR part-I and directed by Engineer-in-charge.

Supply, installation, testing and commissioning of L.T Panel board CPRI approved suitable for 415 Volts, 3 Phase 4 Wire, 50 Hz AC Supply System confirming to IS:8623/93, with IP-65 protection outdoor type plateform mounted along with factory made type panel weather proof, vermin proof, fully ventilated and fabricated out of MS CRCA sheet of 3.15mm thick having copper bus bar of rating 800 Amps current carrying capacity, three phase and one neutral fixed on insulator and bus bar insulated by coloured heat shrinkable sleeves. The panel shall be front / rear openable and having inner & outer shells. The inner shell duly compartmented for each control gear, including Powder coating internally and externally the entire steel surfaces having thickness not less than 100 micron, including seven tank process . All the cover shall be provided with suitable locking arrangements. The size of the outer shell should not be less than 1200mm x 1400mm x 450mm, mounted on angle iron stand made out of angle size 50 X 50 X 6 mm for mounting of panel 45 cm above ground level grouted in PCC 1:3:6, including the following controls gears and suitable size of Digital volt meter & Digital Amp meter with CTs.

(A) IN COMING (a) MCCB , 4 pole ,36KA, 500 Amps, 415 volt 50 Hz AC, with thermal adjustable setting-01 (Incoming) (b) On load change over switch 4 pole 630 Amps-01 Nos Make L&T type CO4-630 Cat Part No CO46300OOOO or equivalent in Legrand/Havells (Euro Load) (c) Panel mounted multi function energy meter of accuracy CL-1.0 rating - 01 No (d) RYB LED indicating lamp panel mounting type (Set of three) - 01 No. (B) OUTGOING (a) MCCB 250A , 4P, 36KA, 415 volt 50 Hz AC with thermal adjustable setting-02 Nos Note (i) All incomming and out going cable connections to be through porper sized alluminium thimbel and cable gland. (ii) Pannel should be mounted on PCC foundation having minimum clearance 45 cm from ground level for connectiong incomming and out going cables. Cost of PCC platform is included in the quoted rate. Note:- Rate for item No 19.06 and 19.07 shall be quoted at item No 19.06 and no claim what so ever in this regards shall be admissible

Total amount of Sch 'A' Part-XII (Sec-I) (Security Wall & Gate) carried forward from pre-priced Schedule.

Sch 'A' Part-XII (Sec-II) (Security Wall & Gate) Note : This schedule is not estimated by MES and the estimated rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

S&F of Ornamantal type steel doors or gates including angle or other section with gusset plates, rails, braces, etc; complete, drilled for fixing of steel sheeting or other covring. Doors, etc; to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging; also fastening and fixing complete. Note:- The cost of ornamental work in Mild Steel Gate shall be included in the rate of above item. The design of the Ornamental Gate shall be got approved from Users after consultations with GE. The cost of ornamental works and aspect of approval shall be deemed included in the rate quoted for above item and nothing extra shall be admissible on this account.

Total amount of Sch 'A' Part-XIII (Protective Work) carried forward from pre-priced Schedule.

Total amount of Sch 'A' Part-XIV(Sec-I) (Air Conditioning) carried forward from pre-priced Schedule.

Sch 'A' Part-XIV(Sec-II) (Air Conditioning) Note : This schedule is not estimated by MES and the estimated rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Supply and fixing, voltage stabilizer for automatic opration, single phase naturally air cooled indoor type & designed for input variation between 160v to 260v with output voltage stabilized at 230v with accuracy of +- 2.5% and of capacity 5KVA.

Sch 'A' Part-XV (Medical Gas Pipe Line System) Note : This schedule is not estimated by MES and the estimated rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Supply, installation, testing and commissioning of Air Compressor (oiless compressor system, compressor in triplex single point connection) 100cft capacity pneumatic with 3000ltr reservoir complete with inlet filter, motor, pully, pressure reducing system and 3 stage Bearthing Air Filtration System for following Make- Kirloskar/ ELGI/Everest

(i) Medicul air outlet(abar)

(ii) Surgical air outlet(4bar)

Supply and fixing Vaccum System with the following systems:- (i) Vacum system (Duplex pump system, skid mounted with facility for single point connection) Make: Kingco or equivalent as approved by GE.

(ii) Vaccum outlet imported

Vaccum Accessories (iii) Ward Vaccum unit with one regulator one collection bottle complete system (Duplex pump system, skid mounted with facility for single point connection ) Make:- Kingco or equivalent as approved by GE.

(iv) Theatre Vaccum unit mounted on the trolley with one vaccum regulator & two collection bottles 92 Unit for each major and minor OT. Make:- Kingco or equivalent as approved by GE.

Supply and fixing matching probes for following outlets:- (i) M- Air 4 Bar

(ii) S- Air 7 Bar

(iii) Vaccum

Supply and fixing copper pipes(third party inspection certificate), seamless hard drawn tested qulity with copper fittings installed on PVC saddless (for Medical gases of following sizes:- (i) 108mm Outer Dia x 2.0 mm thick

(ii) 76.10 mm Outer Dia x 1.5 mm thick

(iii) 42 mm Outer Dia x 1.2 mm thick

(iv) 28 mm Outer Dia x 0.9 mm thick

(v) 22 mm Outer Dia x 0.9 mm thick

(vi) 15 mm Outer Dia x 0.9 mm thick

(vii) 12 mm Outer Dia x 0.7 mm thick

Supply and laying GI tubing medium grade (suitable for LPG gas supply) as per latest norms of size 15 mm dia on wall/floor/concealed including all fittings complete all as specified and directed.

Supply and fix Isolation Valve and guage suitable for supply of compressed air in surgery room, hygine rooms and laboratories sizes as require at site and all as directed.

Supply, install, testing and commissioning electric panel complete with main switch, busbar, starter, meters, autorun switches and indicator lamps complete allied control cabling of suitable size copper conductor complete all as specified and directed.

Installation, testing and commissioning charges of total Medical Gas Supply System

Supply and fixing HP Antistatic rubber tube for vaccum suction complete duly ISI marked as specified and directed. (As per colour code i.e. - Yellow) Make- Meditec England/Dragger Germany

Sch 'A' Part-XVI (Hot Water Supply) Note : This schedule is not estimated by MES and the estimated rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Supply and fixing, Storage water heater 25 ltrs capacity vertical mounting AC 230 Volts BEE 5 Star rating including connecting cord and plug, safety valve, nuts and bolts, PVC Flexible connections with length 450 mm long 15mm dia with brass hexagonal adoptors both side duly ISI marked suitable for hot/cold water complete including grouting of nuts and bolts, complete all as specified and directed Make:-Havells/Venus/V Guard.

Supply and fixing, Storage water heater 50 ltrs capacity vertical mounting AC 230 Volts BEE 5 Star rating including connecting cord and plug, safety valve, nuts and bolts, PVC Flexible connections with length 450 mm long 15mm dia with brass hexagonal adoptors both side duly ISI marked suitable for hot/cold water complete including grouting of nuts and bolts, complete all as specified and directed Make:-Havells/Venus/V Guard.

Sch 'A' Part-XVII (Special Item of E/M Portion) Note : This schedule is not estimated by MES and the estimated rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Supplying, installation, testing and commissioning of SU30K33INT 30 K VA Smart online 3- Phase Intelligent, True Online UPS System has been redesigned to save valuable space and simplify runtime scalability. Power and battery components are combined into a single, small-footprint module (the smallest in its class). A robust internal battery runtime capability can be easily extended by installing additonal modular internal battery packs thourgh the convenient front panel access door. (Backup time of 1 hour with 100% load) Make:- APC/Sukum/Tripp lite or equivalent as approved by GE.

SU30K33INT SmartOnline 3-Phase intelligent, Ture ON-Line UPS System provides mission-critical equipment with the highest level of power protection available. Large capacity 30,000 VA/24,000 watt power module continually converts incoming AC power into filtered DC power and then resynthesizes it back into AC power with a pure sine wave. Perfectly regulated, continous sine wave output with zero transfer time offers compatibility with all equipment types. Smart Online models provide some of the highest levels of isolation from THD (total harmonic distortion) -<3%- allowing equipment to perform at its peak. A 3:1 crest factor safety supports a variety of equipment, even those with wildly-fluctuating power demands.

Battery support can be extended with additional internal battery modules and optional modular external battery frames. A manual bypass switch as well as an automatic bypass function ensure 100% availability of connected equipment by safely passing through AC power when the power module requires maintenance. Three built -in communication ports (RS-232, contact closure and AS-400) work with included Power Alert Software to simultaneously provide shutdown commands and reporting on multiple servers without the need for costly accessories.

An accessory slot accepts an optional internal SNMP card (model # SNMPWEBCARD) for remote shutdowns, reboots and more. A Battery Start Switch allows cold restart of UPS during a prolonged blackout to utilize its batteries for periodic system access or data retrieval. An Emergency Power off button turns UPS output OFF and disables Bypass output. Built -in Emergency Power Off (EPO) interface supports remote emergency shutdown in large facilities. Front panel combination LCD/LED display alerts users to a variety of UPS operational modes and conditions.

Total amount of Sch 'A' Part-XVIII (Sec-I) (DEMOLITION & DISMANTELING OF B/R & E/M ITEMS) carried forward from pre-priced Schedule.

Sch 'A' Part-XVIII (Sec-II) (DEMOLITION & DISMANTELING OF B/R & E/M ITEMS) Note : This schedule is not estimated by MES and the estimated rate indicated as "Rs. 0.00" under Col.5 signifies this fact only.

Dismantling of wash hand/PVC flushing cistern/Looking mirror/Old Sink complete all as specified and directed.

Total amount of Sch 'A' Part-XIX (Earth work and Site clearance for works covered under Sch A Part-II To XVII) carried forward from pre-priced Schedule.

Credit Schedule A Part XX for Rs (-) 1322660.00 (Minus) shall be deducted from quoted amount of BOQ. Note : Tenderer will not quote against this item being firm amount.

M/S KASHCON CONSTRUCTION CO

M/S CONSTRUCTION ENGINEERS

M/S BHATIA BUILDERS AND CONTRACTORS

VADERAS INTERIORS AND EXTERIORS

Onkar Nath Bhalla And Sons Contractor Pvt. Ltd.