Balance work of Aluminum window, doors, shutter and Jali in Devka Garden, Nani Daman. (2nd Call)

Amount

Civil work others

Grouting the joints of flooring tiles having joints of 10 mm width & 10 mm depth using epoxy grout mix and matching of desired gray shade including filling/grouting and finishing complete as per direction EIC & Consultant .

Providing and fixing rolling shutters of approved make made of 50 to 80 mm wide M.S. laths inter-locked together through their entire length and jointed together at the ends by end locks mounted on specially designed pipe shaft with bracket plates, guide channels and arragements for inside and outside locking with push-pull operation including the cost of hood cover and spring etc. complete. (A) Shutters having width below 3.5 Mt. including 1 coat of Rustocap and 2 coat of Hi-Gloss / Matt Finish Metal PU Paint of approved make and shade over all the surfaces etc. as directed.

Providing and fixing rolling shutters of approved make made of 80 mm wide M.S. laths inter-locked together through their entire length and jointed together at the ends by end locks mounted on specially designed pipe shaft with bracket plates, guide channels and arragements for inside and outside locking with push-pull operation including the cost of hood cover and spring etc. complete. (B) Shutters having width 3.5 M. and above including 1 coat of Rustocap and 2 coat of Hi-Gloss / Matt Finish Metal PU Paint of approved make and shade over all the surfaces etc. as directed.

SEC:5 Doors and Windows work ALUMINIUM WORKS - Providing material and labour for fixing in position frames, shutter for any type of aluminium work for any type of door, window, partition, made out of any type of aluminium sections of approved make having minimum 50 micron pure polyester powder coating of approved shade, texture & colour of approved make for all floors, all levels, all heights, all shapes, all sizes including cutting, bending, crimping, fabricating in best workmanship manner etc as per the drawing, specification and as directed by Architect or Engineer-in-Charge. Contractor shall prepare shop drawing based on concept drawing and get approved from the consultants before procurement of material. All loose material shall be approved. Mockup of one/two window shall be executed as per approved shop drawing with all hardware. Work shall carried out as per the approved shop drawings, approved mock-up and approved sample. Actual weight of installed Aluminium sections (for using fabrication without considering any wastage) shall only be measured and shall be considered for the payment. Contractor shall provide guarantee for stability, water tightness etc for 12 months after defects liability period. Rate shall be inclusive of providing aluminium sections, cutting, fabrication, errection and fixing to the best workmanship manner, including 1) Sheet metal screws and casted solid aluminum corner cleats fixed with external byttins with a spring for rapid and secure joint assembly for casement and sliding shutter and frame; 2) Glazing clips for receiving infill panel; 3) Best quality wool pile where ever shutter touches the frame and compatible microwave cured EPDM rubber; 4) Dash Anchor fasteners of HILTI HRDUGT or equivalent for fixing the frame assembly to the RCC or masonry surfaces. Minimum 1 anchor fastener shall be used for every 600 mm length of section for stability of frame. 5) 10mm GI tie rod for connecting vertical stile at top and bottom for aluminum door shutter and 4mm thick solid aluminium corner cleat of full thickness of section for connecting style and horizontal rails; 6) providing and fixing packing (rough ground) in full periphery/ at every 600mm c/c with average 6 mm thick PVC spacer/ compact sheet of width (equal to section width less 30mm for backer rod and sealant); 7) Filling the gap between wall and frame on both sides (outside and inside) with polyethylene baker rod of avg. 10 mm thickness of approved make and color and then sealing the remaining gap with neutral grade G/M (Glazed & Metal) weather silicon sealant of approved make and color. 8) Termite treated seasoned teak wood as infill material to installe hardware in door shutter and frame as and when required. and excluding the cost of necessary hardware and Glazing or Infill material.

Providing material and labour for fixing 6mm thick Clear Toughen Glass as per approved sample of any size, any shape and specified thickness in frame and shutter work with necessary cutting of glass as per drawing & specifications including providing and fixing EPDM quality rubber/ silicon sealant/ structural sealant and 3M tape on the periphery of the glass as per the required thickness etc. complete at all floors/ all levels/ all heights as per the directions of Engineer in charge. Actual installed quantity shall be measured and paid.

Providing material and labour for fixing factory made and pressed laminated 35mm thick flush door shutter of specificied thickness made of ISI marked non decorative type flush door shutters confirming to IS- 2202 (Part 1), core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers (IS 710 Grade) on both faces of shutters having 1 mm thick decorative type laminates of approved make, shade, finish on both faces of shutter fixed with phenol formaldehyde synthetic resin type adhesive conforming to IS 848 including providing and fixing external lipping with 2nd class teak wood battens, exposed (37mm x 12mm)/ concealed (35mm x 12mm) on all edges of door shutter as required with 2 coats of synthetic enamel painting including 1 coat of wood primer & lapi/ lacquer polishing with primer to all exposed side of lipping, all as per approved drawing, for all floor, all level all height etc. complete as directed by Engineer-in-charge. Measurement including lipping shall be considered for payment. Necessary hardware like hinges, pivot, handle, tower bolts, locks etc shall be separately measured and paid in the relevant tender items. Cost of laminates shall be paid in relevant tender item.

Providing material and labour for fixing 1 mm thick Laminate sheet of any size, any shape, any color, any texture of approved make and as per approved sample (approved by architect) on Non decorative flush door, panelling work, fixed partition, any ply surface etc with necessary nails, screws, adhesives as per drawings and as per approved sample. The rate shall be for all heights, all floors, all places etc complete as directed by engineer in charge. Actual laid area shall be measured and paid without considering any westage. Laminates and ply shall be factory pressed.

Design, Fabrication, Supply, Installation Grill/ Jali made out of precast GRC (Glass Fibre reinforced Cement) of 25 mm thick in required size and in approved colour, shape and pattern of approved make and as per manufacturers specifications, such as all decorative articles should be made by using high power spray machine, using Cem-fill manufactured AR Glass fiber with minimum ZrO2 17% including necessary scaffoldings for all heights, fixing the individual or composite elements and their proper jointing/ sealing with approved adhesives & sealants and drilling holes in existing MS Steel and fixing on existing MS structure to external façade with MS Hot Deep Galvanized/ SS 316 fasteners and anchor bolts of suitable dia. & lengths, grouting with sealants etc. all complete as per drawing/ dimension and directions of Architect or Engineer-in-Charge. MS work shall be paid in relevant tender item.

RAJRATH CONSTRUCTION (BID ID -8825)