SPECIAL REPAIR TO BLDG NO SP-12 JCOs LIVING AND MESS, GE 864 EWS AT BB CANTT, SRINAGAR

Amount

Dismantling plain or corrugated steel sheeting any gauge, thickness incl nainital or similar pattern roof-covering, complete all as specified and directed.

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S &F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Dismantling timber scantlings 40 Sqcm and over in section, in unframed work in any position, complete all as specified and directed.

S&F 2nd class hard wood clean sawn timber fixed in scantling, complete all as specified and directed

Fixing only 2nd class hard wood clean sawn timber fixed in scantling, complete all as specified and directed

Dismantling of wall and ceiling boards (fiber pulp, insulation, etc..) or unsulation boards/slabs, any thickness, including cover fillets, complete all as specified and as directed.

S&F 6MM Tthick Non asbestos fibre cement designer board /pre Laminated self embossed texture designer board E-Board classic size 600x600 m ,HPSC (High pressure steam cured) to be fixed or inserted to pre laminated GI Frame work for Seamless ceiling size 600mmx600mm with main runner 38x24x0.9mm thick cross tee 8.6x0.9mm and wall angle 19x19x0.9mm duly suspended with 6mm dia GI bar hanger 1200mm centre to center both ways fixed with steel dash fasteners or from purlin from the roof with alignment dip complete as per manufacturer's instructions and as directed. Note: Removing & Refixing of electric fittings & wiring is responsible of contractor with any extra cost.

S&F 9 mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work commercial type as in ceiling fixed with nails, complete all as specified and directed

S&F 6 mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work commercial type as in ceiling fixed with nails, complete all as specified and directed

S&F 12 mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work commercial type as in wall fixed with nails, complete all as specified and directed

M&L for 6mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces; fixed with nails to timber frame work, complete all as specified and directed

S&F 2nd class hard wood sec area exc13 & n exc 25 Sqcm as in plain fillets, square, rectangular in section, clean sawn, secured with nails or brads, complete all as specified and directed

S&F 2nd class soft wood plain clean sawn fillets square, rectangular or triangular in section exc 6 & n.exc 13 sqcm secured with nails or brads, complete all as spd and directed.

Dismantling boarding, any description, fixed in any position with nails all as required, complete all as spd and directed

S & F 20 mm thick, second class hard wood boarding clean sawn, planed one side with butt joints and fixed with nails in any situation as in eaves board, etc., complete as specified and directed.

S & F 40 mm thick, second class hard wood boarding clean sawn, planed one side with butt joints and fixed with nails in any situation as in planck board, etc., complete as specified and directed.

S&F 12 mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work commercial type as in flooring fixed with nails, complete all as specified and directed

S & F 2mm thick Linoleum, plain coloured, laid in floors including stretching, cutting and fitting sealed down with an approved adhesive, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) n. exc 1.5 Sq.m each,complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 square metre but n.exc 4 square metre each, complete all as specified and directed.

S&F 2nd class hardwood plain solid straight chowkhats and frames wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and directed.

S&F 35 mm thick 2nd class soft wood plain framed panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board with commercial face veneers, complete all as specified and directed.

S&F 30 mm thick 1st class soft wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze et (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-I section -8 , clause 8.24 (a), complete all as specified and as directed .

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube suppling and fixing in opening as per specification and drawing, complete all as specified directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rail MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitabele PVC sheet beading and joined together with solvent cement suppling and fixing in the frame at site as per specification and drawing, complete all as specified and directed.

S & F aluminium (powder coated with approved colour) ventilator, partialy glazed and partialy louvers, outer frame & mullion fabricated with aluminium section of size 82.50 mm x 38.00 mm x 1.70 mm thick (Cat No 20036), half portion glazed with 4 mm thick frosted glass including rubber beading, & glazing clip, half portaion louvers of 80 mm wide & 4 mm thick frosted glass including aluminium louver patti including S.S wire gauge of fixing of 0.36mm dia and 1.40 width of aparture with 25x3mm think aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position and aluminium (anodised) grill, square, ractangular or similar section, fixed with channel of size 38 x 12 x 13mm etc., complete all as specified and directed

S & F aluminium powder coated openable double window (Gauzed and Glazed) made of the following specifications, complete all as spd and directed :- (Net external size will be measured. Following items are included in this unit rate.) (a) Aluminium frame powder coated all around of hollow section 63 mm x 38 mm x 1.50 mm thick. (b) Provn of glazed openable shutter of section 44 mm x 18 mm x 1.25 mm provided with 3.50 mm thick tinted glass with suitable EPDM beading,02 Nos 100mm powder coated aluminium hinges, 02 Nos 100 mm long powder coated aluminium tower bolts, 01 Nos100 mm powder coated aluminium handle and 01 No hook & eye & any other fitting reqd for each shutter. (c) -ditto- as in para 10 (b) above but using stainless steel wiremesh 0.36 mm dia and 1.40 mm aperature in lieu of 3.50 mm thick tinted glass. (d) Aluminium powder coated grill of weight not less than 2.60 Kg/Sqm on external side with suitable frame/aluminium runner to be fixed on the window frame. (e) Repair to the jamb, cills and all sides around the window is incl in unit rate. The repair finishes to match the existing surfaces like tiles, plastering etc.

S & F aluminium bow handles, cast type, anodised size 125 mm, complete all as specified and as directed .

S & F aluminium anodised barrel tower bolts of size 150 mm extruded section and fixed, complete all as specified and as directed .

S & F aluminium anodised barrel tower bolts of size 200 mm extruded section and fixed, complete all as specified and as directed .

S & F aluminium bow handles, cast type, anodised size 200 mm, complete all as specified and as directed .

S&F butt hinges, medium weight cold rolled, mild steel of size 100 mm, complete all as specified and as directed

S&F Aluminium alloy, anodised, sliding door bolt 300 mm in length with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M&L for preparation of old wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing ), removing serviceable tiles to store and rubbish off the premises, complete all as specified directed.

M&L Virified Ceramic light shade tiles 10 mm thick (square/ rectangular polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in cement to match white or coloured over and including 15mm thick screed bed or bedding layer in cement mortar 1:4 , complete all as specified and directed

M & L for Non - skid Ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured ,over and including 15mm thick screed bed or bedding layer in CM 1:6 ,complete all as specified and directed.

M&L for Glazed ceramic coloured tiles in vertical surfaces 450mm x 300mm x 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in Cement mortar 1:3, complete all as specified and directed.

M&L Vitrified Ceramic light shade tiles 10 mm thick (square/ rectangular polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in cement to match white or coloured over and including 10mm thick bedding layer in cement mortar 1:3, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and in pavings not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

M & L 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection / hard standing etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2, complete as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, compplete all as specified and directed.

S&F 15 mm thick 2nd class soft wood clean sawn boards or planks, width n.exc. 25cm as in wall boarding, complete all as specified and directed.

Taking down cement plaster of any description, thickness and in any position including raking out joints, hacking for key, scrubbing down with water etc , and removal the rubbish/ demolished material outside defence land, complete all specified and directed.

M&L for 15 mm thick rendering on fair faces of brick /concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick rendering on other than fair faces of brick / concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and directed.

M & L preparing surface of newly plastered walls and applying two coats of oil bond distemper over chalk whitening preparatory to distempering, complete all as specified & directed..

M&L Preparing newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer, complete all as specified and directed..

M & L preparing old surface of walls and applying one coat of oil bond distemper complete all as specified and directed.

M&L Preparing old surface of walls and applying two coats of cement base paint, complete all as specified and directed.

Taking up or down 15mm dia steel tubing and connection, including cleaning for re-fixing or removal to store, complete all as specified and directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store 20 mm dia complete all as specified & directed.

S & F 15 mm dia GI tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, complete all as specified & directed.

S & F 20 mm dia GI tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

S&F in repairs bib tap, 15mm bore, cast copper alloy chromium plated fancy type long body with capstan haed handle screwed down high pressure screwed for iron pipe or for brass ferrule , complete all as specified and directed.

S & F in repair Stop valves, 15mm bore cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified and directed.

S&F in repair 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S&F in repairs 1000 litres capacity rotational moulded polythene water storage tanks (cylindrical vertical, with closed top), hoisted and fixed in position as specified in SSR Part I , complete all as specified and directed.

S&F 20mm bore ball brass valves high pressure, with polythene float & fly nuts complete, screwed for iron pipe or brass ferrule, complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm, complete all as specified and directed.

S&F 10 litres capacity PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle including brackets, complete as specified and directed.

S&F in repair vitreous china wash down water closet pan with fixing bolts, trap (pedestal pattern), white, (excluding flushing cistern and flush pipe), complete all as specified and directed.

S & F in replacement curtain rod 20 mm dia, mild steel, chromium plated, fancy type with fixing brackets and knobs at both ends as per site requirement complete all as specified and directed by Engineer-in-Charge. Note:- The cost of brackets and knobs is deemed to be included in the quoted rate. Nothing extra shall be paid on this account, complete all as specified and directed.

S&F in repair wash hand basin vitreous china size 550x400mm white flat back as approved by GE ,waste,chain plug,pvc connection, pvc waste pipe comp all as specified fixed in repair, complete all as specified and directed.

S&F in repair CP Mixer single lever basin mixer fancy type for WHB / Sink with double action for hot/Cold water, complete all as specified and as directed.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for fdn for shafts, cills, cesspits, manhole pier holes n.exc 10Sqm on plan and getting out inhard/dense soil, complete incomplete all as specified and directed.

M&L for Plain cement concrete 1:3:6, type C-2 using 40 mm graded crushed stone aggregate, as in foundations, filling and mass concrete, complete all as specified and directed.

Returning filling in including spreading leveling, watering and well ramming in layers n.exc 25cm thick in soft/loose soil, complete all as specified and directed.

Removing of excavated soil to a distance n.exc 50m and depositing where directed by the Engr-in-Charge at a level n.exc 1.50m above the starting point, complete all as specified and directed.

M&L for Brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:4, complete all as specifed and directed.

M&L for Plain cement concrete 1:2:4 type B1, using 20mm graded stone aggregate as in coping etc including weathering, slightly rounded or chamfered angle and throating, complete all as specified and directed.

M&L for rendering 10mm thick on fair face of brick work or concrete surface in cm 1:4 all as specified finished even and smooth without using extra cement, with using water proofing compound 3% by weight of cement, complete all as specified and as directed. Note :- WPC shall be measured and paid seperately

M&L for rendering 15mm thick on other than fair face of brick work in cm 1:4 all as specified finished even and smooth without using extra cement, with using water proofing compound 3% by weight of cement, complete all as specified and as directed. Note :- WPC shall be measured and paid seperately

Supply only Integral Water Proofing Compound and used as per manufacturer instruction, complete all as specified and directed.

M&L for 150mm bore RCC pipes Class NP2 with collar ,laid in trenches and jointed including dismantling of old unservicable pipe, complete all as specified and directed.

M&L Plain Cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in concrete bed to drain pipes 150 mm internal bore including packing under and hunching against the sides of pipes after they are laid and tested, complete all as specified and directed.

M&L pre-cast Reinforced cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in cover slab for manhole etc including necessary form work, complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with MS wire (annealed) not less than 0.9mm dia, complete all as specified and directed.

M&L for Mild steel round bars 10mm dia as in handles for manhole cover, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not other wise provided, Complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for, complete all as specified and directed.

S&F in repair PVC (SWR) floor trap, 75mm dia bore plain with grating including jointing with solvent cement complete all as specified and directed

M & L 75 mm thick PCC 1:4:8 Type D2 (using 40 mm graded crushed stone aggregate) as in sub base to floors, complete all as specified and directed.

M&L 25 mm thick plain cement concrete 1:2:4 type B-0 ( using 12.50 mm graded crushed stone aggregate) as in sub base of floors finished even and fair, complete all as specified and directed.

M&L for rendering 15mm thick, in cement mortar (1:3) on concrete/ brick surface of sunken portion, mixed with Dr Fixit pidiproof LW+ or equivalent @ 200ml/50Kg of cement and fixed with 32mm GI pipe 450mm long sport, complete all as specified and directed.

M&L for applying 2 coats of flexible polymer acrylic water proofing coating, 1mm thick (Dry film in two coats) using Dr Fixit pidifin 2K of M/S Pidilite Industries or equivalent including necessary pond testing for 48 hrs in sunken portion, complete all as specified and directed.

M&L for treatment to sunken slab by applying primer @ 0.5 Kg/Sqm over the prepared suface and hot blown cutback bitumen @ 0.70 Kg/Sqm providing and laying3mm APP membrane on min 15cm over lap and screed bed 25mm thick, in cement mortar (1:3) on above sunken portion, mixed with Dr Fixit pidiproof LW+ or equivalent @ 200ml/50Kg of cement, complete all as specified and directed.

M&L for Plain cement concrete (1:5:10), type E2, using 40mm graded crushed stone aggregate in sunken floor surface finished fair, complete all as specified and as directed.

Providing plain cement concrete [1:2:4] type B0 using 12.5 mm graded crushed stone aggregate 25mm average thickness as in sub base of floor of wc/bath/toilet finished even and smooth without using extra cement mixed with water proofing compound Dr Fixit pidiproof LW+ or equivalent at 200ml/50kg of cement, complete all as specified and as directed.

S&F in repair glass shelf 500x60mm (with ABS Brackets) Cat No- BEA-47 (make- Prayag), complete all as specified and directed

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60 cm long between flanges, complete all as specified and directed

M&L for taking down carefully existing old burnt out / unserviceable aluminium / copper point wiring system any type/ size and any description complete for light, fan,bell,socket, power points etc complete including removing the all type of fittings & fixture alongwith it connected fixing acessories such as all switches, sockets, ceiling roses, holder,regulators,bell etc complete and removing of all the old materials from the site for to taking as a schedule of credit, complete all as specified and directed.

M&L for making single phasing point wiring system used as copper conductor wire for phase and neutral wiring system the wire made out of PVC insulated FRLS of 1100 volt grade with having multistranded copper conductor wire of size 1.5 Sq.mm (Nominal area) ISI marked drawn through wiring system surface on wall or concealed in wall with the help of heavy duty ISI mark PVC casing capping strip / PVC conduit pipe ISI mark in any lengthy wiring system and along with its all connected fittings accessories including providing of pressed steel terminal sunken boxes or heavy duty PVC box and duly fixed it concealed in wall or surface on wall and alongwith providing of modular type of back and face top cover plate frame or electro plated plastic laminated sheet for housing / mounting of any type/size switches sockets, regulators etc and including using /drawing of one run of single wire 1.5 sqmm PVC insulated FRLS wire 1100 volt grade ISI marked with multistranded copper conductor wire used as a continuous earth wire for point wiring complete system and including making the good to all disturbed surfaces of wall/ceiling area of new wiring system and to match to it as per the existing surface of wall/ceiling etc. for the following, complete all as specified and directed.

One light point / fan point wiring system controlled by one way switch, complete all as specified and directed.

One 3/5 pin type 5 Amp socket outlet point fixed on same board and controlled by one switch of one way point wiring system, complete all as specified and directed.

One 3/5 pin type 5 Amp socket outlet point fixed on independent board and controlled by one switch of one way point wiring system complete , complete all as specified and directed.

One bell point and controlled by one bell push switch of one way point wiring system complete , complete all as specified and directed.

Description of all as per serial item No 96 here-in-before, but using PVC insulated FRLS wire 1100 volt grade with multistranded copper conductor wire of size 2.5 Sq. mm (Nominal area) ISI Marked for power socket point on indenpent board point wiring system and also providing of 2.5 sqmm PVC insulated FRLS wire 1100 volt grade ISI Marked with multistranded copper conductor wire used as a continuous earth wire for power point wiring system, complete all as specified and directed.

Supply and fixing of modular type switch of 5/6 Amps 220 Volts AC, one module, complete all as specified and directed.

Supply and fixing of modular type socket of 5/6 Amps 220 Volts AC, 3/5 multi pin type with two modular , complete all as specified and directed.

Supply and fixing of modular type switch of 15/16 Amps 220 Volts AC one module, complete all as specified and directed.

Supply and fixing of modular type socket of 15/16 Amps 220 Volts AC 5/6 multi pin type with two modular, complete all as specified and directed.

Supply and fixing of modular type switch bell push of 5/6 Amps 220 Volts AC, one module , complete all as specified and directed.

Supply and fixing of bell Ding Dong Type, 220 volt AC, Single Pole, complete all as specified and directed.

Supply and fixing ceiling rose three terminals type made out of polycarbonate , isolated body complete all as specified and directed.

Supply and fixing of angular/batten type shape lamp holder with PVC/ Polycarbonate insulated body, alongwith brass adhapor and back plate for housing of bulb including providing of LED rechargeable of capacity 9 watt , complete all as specified and directed .

Supply and fixing of one/two modular type step type electronic fan regulator with having hum free step alongwith speed control know, complete all as specified and directed.

Supply and fixing of LED tube light fitting of 1x 20W/22W 220V AC decorative box type with driver, holder including LED tube light with having energy efficient type complete including providing of suitable type flate fexible cable for electric connection from ceiling rose to fitting, complete all as specified and directed.

Supply and fixing of LED tube light fitting with high out put diffuuser 2 feet long of 9/10 Watt 220 volt AC decorative type with driver holder and LED lamp with having energy efficient type complete including providing of suitable type flate fexible cable for electric connection from ceiling rose to fitting, complete all as specified and directed

Supply and fixing of recessed / ceiling concealed mounted flate slim type unique square LED luminaire panel type fitting of size 600 mm x 600 mm of rating capacity in 35W/36Watt 220 volt AC recessed type with high efficiency PMMA didduser soft glare free light complete with driver, holder & LED lamps suitable used for roof ceiling and required fitting use in both warm/white type colour complete including cutting /making suitable size of hole on wooden ceiling board surface area for fixing/intallation of ceiling light fitting purposed complete work and providing of suitable type of flate fexible two/three core cable and making electric connection, complete all as specified and directed.

Supply and fixing of surface wall mounted decorative bracket light fitting with having stainless steel rust free fixture with white glass diffuser alongwith bulb holder based adhaptor suitable used for 7.5W / 9 W LED filament lamp E27 base system including providing of 1N x 9W LED lamp in required fitting use in both warm/white type colour complete light fitting set and including providing of suitable type of flate fexible two/three core cable and making electric connection , complete all as specified and directed.

Supply and fixing surface mounted LED decorative type angle adjustable sport light / bed side study lamp light fitting with lamp in matt finish for premium aesthetics with based of suitable rating capacity 7Watt LED fixture in required fitting use in both warm/white type colour complete light fitting set and including providing of suitable type of flate fexible two/three core cable and making electric connection, complete all as specified and directed.

Supply and fixing surface mounted LED bulk head luminaries light fitting of rated capacity 10W including LED lamp & driver suitable used for out door type with dust and water proof with energy efficient complete and including providing of suitable type of flate fexible two/three core cable and making electric connection, complete all as specified and directed.

Supply and fixing of LED street light fitting of rated capacity 35Watt 230 volt AC with having LED driver,lamp bracket with impact and corrosion resistant including thermal management in multiple optices complete with IP 65/66 protectiuon suitable for out door type made out of high pressure die cast hosing with heat resistant glass complete light fitting set including providing of suitable dia of GI bracket and it to as per match/setting thefitting fixture base hole attechment system and including providing of suitable type of flate fexible two/three core cable and makong electric connection, complete all as specified and directed.

M& L for taking down carefully of existing ceiling fan /exhaust fan and geyser any type any capacity and after removing fan blade and body parts including cleaning all dust particles and filling cavities with filler material, oiling ,greasing including applying painting work on any type of fan with blade and geyser frame complete body system by two coat of synthetic enamel paint as per existing type of colour and after painting work assemble the same along with all connecting fixing accessories like rubber rell, nut ,bolt ,washer,lock pin, clamp and including providing of fan hook etc and hanging and refixing the same position with the help of nut bolt and washer etc and making all electrical wire connection, complete all as specified and directed.

Supply and fixing of ventilating exhaust fan made out of complete sturdy engineering plastic body with having motor ,frame louvers & shutter and blade suitable for of size 200 mm 230 Volts including making of suitable type /size of hole on wall etc, complete all as specified and directed.

Supply and fixing of ventilating exhaust fan made out of mild steel body, complete with louvers,and shutter operational of size 300 mm sweep suitable to work on 230 Volts 50 Hz, 1200 RPM, coper winding including making of suitable type /size of hole on wall Including takind down of existing fan , complete all as specified and directed.

Supply and fixing of wall mounted fan 400 mm sweep single phase 230 Volt Ac complete with blade and connecting fixing accessories including takind down of existing fan, complete all as specified and directed.

Supply and fixing of ceiling fan of size 1200 mm sweep min air delivery 210 CFM with BEE normns 5 star rating of single phase 220 Volt AC along with blade and down rod complete and including taking down of old unserviceable fan and providing of suitable type flate fexible cable and making electric connection, complete all as specified and directed.

Supply & fixing of electric water hearter storage type steel body with inner cooper tank and heating elements up to 2KW of storage capacity 25 Ltrs 5 star rated complete with all connecting fixing accessories including takind down of existing heater, complete all as specified and directed.

Supply and fixing of sheet metal enclosure duly powder coated with double pole and neural enclosure with a two pin and earth plug and top and having mounting chanel and complete with one 01 MCB SP 20 Amp and making all necessary electrical connection and dully fixed surface on wall or concealed on wall and making good the disturbed wall surface all as required at site, one module , complete all as specified and directed.

Supply and fixing of sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrengment system suitable of size/type for vertical type distribution board vertical loadline type of rating VTPN 4 way type 415 volt 3 phase AC supply holding system with IP protection rating with ISI marked and having fitted neutral and earth link bus bar and mounting base chanels and blanking plates suitable for holding of main MCCB as incommer and out going MCB complete system alongwith providing and mounting in side of DB box of 01 No of MCCB TP 160 Amps with breaking rupting capacity 25 KA and having adjustable setting type and also providing of 08 Nos of MCB SP 63 Amps 10KA 'C' curve type of the same manufacture make as per of distribution board make complete set and including dully fixed surface on wall or concealed in wall and making all necessary electrical and also refixing the wiring connection including taking down of existing meter and DB, complete all as specified and directed.

Supply and fixing of sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrengment system suitable of size/type of distribution board of rating SPN 8 way type 220 volt AC supply system and having neutral and earth link bus bar and mounting base chanel suitable for holding MCBs incommer and s outgoing system complete set and including dully fixed surface on wall or concealed in wall and making all necessary electrical and also refixing the wiring connection including taking down of existing meter and DB complete all as specified and directed.

Supply and fixing of sheet metal enclosure box duly powder coated & framing work with locking system and having double door fixing arrengment system suitable of size/type of distribution board of rating SPN 4/6 way type 220 volt AC supply system and having neutral and earth link bus bar and mounting base chanel suitable for holding MCBs incommer and s outgoing system complete set and including dully fixed surface on wall or concealed in wall and making all necessary electrical and also refixing the wiring connection including taking down of existing meter and DB complete all as specified and directed.

Supply and fixing of MCB SPN 40 to 63 Amps, 230 Volts, 50 Hz AC supply suitable for 'C' series, 10 KA breaking capacity, complete all as specified and directed.

S&F MCB SP 6 to 32 Amps, 240 Volts, 50 Hz AC supply suitable for 'C' series, 10 KA breaking capacity, complete all as specified and directed.

Supply and fixing of Sub main wiring system with two runs PVC insulated FRLS wire,1100 volt grade with multistranded copper conductor wire of size 2 Run of 10 Sqmm and 1 Run of 10 Sqmm (Nominal area) (ISI Marked) any type any length drawn through in heavy duty ISI mark PVC Casing capping / PVC conduit of suitable size along with its all fittings and connected accessories and duly fixed concealed on wall or surface on wall including taking down old unservicable sub main wiring system complete and making good all disturbed surfaces match to the existing surface, complete all as specified and directed. Note:- 3 runs of 10 sqmm wire and one run of PVC caseing/ capping/ conduit shall be measured as 1.00 running meter .

Supply and fixing of Sub main wiring system with two runs PVC insulated FRLS wire,1100 volt grade with multistranded copper conductor wire of size 2 Run of 6 Sqmm and 1 Run of 6Sqmm (Nominal area) (ISI Marked) any type any length drawn through in heavy duty ISI mark PVC Casing capping / PVC conduit of suitable size along with its all fittings and connected accessories and duly fixed concealed on wall or surface on wall including taking down old unservicable sub main wiring system complete and making good all disturbed surfaces match to the existing surface, complete all as specified and directed. Note:- 3 runs of 6 sqmm wire and one run of PVC caseing/ capping/ conduit shall be measured as 1.00 running meter .

Supply , laying and testing of LT cable XLPE insulated screened,PVC bedded galvanized steel strip or wire armoured electric power cable ( heavy duty ) with aluminium conductor 1100 volt grade cross section area of size 50 sqmm 3.5 core including laid in trenches or fixing on poles or passing through pipes complete including taking out of old unserviceable cable any type any size, complete all as specified and directed.

M&L for earthing work complete with galvanised steel earth plate electrode 60 Cm X 60 Cm X 6 mm thick buried directly in ground vertically to a depth not less than 2.25 mtr deep below ground level with top edge of earth plate at a depth not less than 1.5 m below normal ground level and connected to galvanised earth lead wire 4.0 mm dia by means of bolts, check nuts and washers of galvanised steel and to be protected by GI pipe 15 mm bore light grade & connected to earth test point/main switch board or main control board and also providing charcoal or coke and salt in alternative layers, necessary excavation and earth work in any type of soil all as shown in Electrical Plate No 3 of SSR part -I. and also making arrangment of 20 mm dia bore galvanised iron pipe (medium grade) for water and making funnel, wire mesh,and also including provision of concrete pit cover framing work in PCC (1:2:4) type B-1 using 20mm graded of stone aggregate with XPM (weight not less than 4 Kg/Sqm) with top concrete pit cover and handle for lifting of cover complete work all as specified and directed

Supply and fixing of rigid non metalic PVC conduit of size 20/25 mm bore heavy duty with all fitting laid in trenches/ wall including providing clamping arrangment for holding of pipe on wall in proper size of clamps, nut bolt ,and washer etc, complete all as specified and directed.

Supply and fixing of GI earth countinuity earthing lead of size 4 mm dia bore galvanised iron or steel wire with all fitting dully laid in trenches/ wall including providing clamping arrangment for holding on wall in proper size of clamps, nut bolt ,and washer etc, complete all as specified and directed.

Notes :- An amount of Rs.106024.00 on account of Credit Schedule for Schedule 'A' Part-II shall be deducted from total quoted amount of BOQ to arrive at the contract sum.

M/S TAJ DIN KHARI (BID ID -3423195)

M/S NEW IQBAL ENTERPRISES (BID ID -3423424)

M/S U.K. ENTERPRISES (BID ID -3422488)

M/S Vivek Gupta and Co (BID ID -3423191)

M/S BASHIR AHMAD MIR (BID ID -3422363)

M/S D N Enterprises (BID ID -3422817)

M/S Tajamul Ah Buchh (BID ID -3423444)

M/S MUSHTAQ AHMAD BHAT (BID ID -3423408)