PROVN OF BATHROOM/TOILET BLOCK AND SHED OF AT BI-28 BLDG OF CERTAIN UNIT, PROVN OF PANELLING ON WALL AND CURVED ROOF AND TILING WORK AT BLDG NO OD-16, PROVN OF PARKING SHED WITH HARD STANDING AND SHED AT THE BACKYARD NEAR BLDG NO O-13, PROVN OF CONNE

Amount

SCHEDULE 'A' PART-I (B/R WORKS) M&L for surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil.complete all as specified and directed.

M&L for excavating over areas not exceeding 1.5 metre deep and getting out in soft/loose soil complete all as specified and directed.

M&L for excavating in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth in soft/loose soil complete all as specified and directed.

M&L for excavating in post holes (or similar holes) each not exceeding 0.5 Cum, getting out, returning filling in and ramming earth or broken rubble mixed with earh around in layers not exceeding 25 cm for soft/loose soil complete all as specied and directed.

M&L for returning filling in including spreading, leveling, watering and well ramming in layer not exceeding 25 cm for soft/loose soil complete all as specified and directed.

M&L for removing excavated soil not exceeding 50 m and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed.

M&L for hardcore of gauge not exc 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to true surface with broken stones complete all as specified and directed.

-ditto- but hardcore with stones of size exc 63 but not exc 100 mm

Cutting/demolition of concrete/bituminous road surface in ground floors and pavings not exc 15cm thickness (below or above ground level) etc and removal of debris from site complete all as specified and directed.

Demolition of brick work or stone boulder masonry built in cement mortar including all quaries, arches pillars etc and removing off the site complete all as specified and directed.

Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Dismantling of cast iron or reinforced concrete drain pipes, 100 mm bore, jointed in cement mortar and taking out of trenches, complete all as specified and directed.

Dismantling structural steel work with mild steel sheet covering as in doors, gates, hangar doors etc but excluding framed trusses complete all as specified and directed.

Taking down chowkats of frames with shutters (without taking off shutters, from the frames) not exceeding 1.50 Sqm each and removing off the site complete all as specified and directed.

M&L for plain cement concrete (1:3:6) type C2 using 40 mm graded aggregates in foundation filling and mass concrete complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B2 (using 40 mm graded aggregates) in foundation filling and mass concrete complete all as specified and directed.

M&L for plain cement concrete (1:2:4) type B2 using 40 mm graded aggregates in surface channels and drains complete all as specified and directed.

M&L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi tred/stopped ends etc.

M&L for plain cement concrete (1:2:4) type B1 usi ng 20 mm graded aggregates in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones , bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including formwork complete all as specified and directed.

M&L for damp proof course to horizontal or vertical surfaces 25 mm thick including necessary formwork in cement concrete 1:2:4, type B0 using 12.5 mm graded aggregates complete all as specified and directed.

M&L for brickwork with fly-ash old size bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for brickwork with fly-ash old size bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 complete all as specified and directed.

M& L for brickwork with fly ash old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

M&L for cutting holes in brick wall exceeding half brick but not exc one brick thick walls for inserting hold fasts for mild steel grills and making good dismantled portion in cement concrete 1:2:4 type B1 (using 20 mm graded aggregates) including necessary formwork and making good surfaces as per existing finisjhes complete all as specified and directed.

M&L for 2nd class hardwood, plain soild, straight chowkhats and frames, wrought, framed rebated on the soild, rounded or chamfered, put together, with glue, pinned at joints complete all as specified and directed.

S&F 30mm thick Factory made 2nd class hard wood glazed & skleton shutters, open rebated and prepared to received glass, gauge etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-I section 8, clause 8.20(a) complete all as specified and directed.

S&F Factory made 35mm thick with 2nd class hard wood, rail and style factory made plain framed panelled shutter(two panel) with lock, rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail & style as per IS:1003(Part-I) kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F PVC solid door frame of size 50 x 47 mm made out of 5 mmthick prelaminated single side PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F 30 mm thick factory made both side prelaminated solid panel PVC door shutter consisting of frame made out of MS tube of 19 gauge thickness and size of 19mm X 19mm for stiles, top and bottom rails, treated with a coat of metal primer, MS frame covered with heat moulded prelaminated PVC 'C' channel for stiles and both side prelaminated PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; stiles and rails feathered at edges, panelling of both side prelaminated PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement and fixing in frame complete all as specified and directed.

S&F stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 complete all as specified and directed. (NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete)

M&L for Rolled mild steel in joist, angle, channel or tee sections, fixed independently without connecting plates etc. (cut to ordinary length i.e. within 20 mm of the length indicated) Gde Fe-410-W(Gde-E-250) quality-B complete all as specified and directed.

M&L for Rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Gde Fe-410-W (Gde-E 250) quality-B complete all as specified and directed.

M&L for Rolled mild steel framed work, Fe-410W(Gde-E-250) quality-B as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering), running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

M&L for structural steel work Fe 410-W (Gde-E-250) quality-A in roof trusses (framed), trussed, purlins, crane gantries, rials and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and as directed. (NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete)

M&L for Rolled mild steel in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes without any attachment Gde Fe 410W complete all as specified and as directed.

M&L Bands, straps, supports or stays for rainwater, ventilating, pipes, including bolts, if required hooks (stays ) heavy for large gates hook and pintle hinges large hasps and staples, chains hand made sliding bolts, clamps, hold fasts, plain angle cleats for securing purlins to wood trusses or rafters knee piece inserts two way and three way straps plate washers and similar small articles conforming to fe-290 Gde E-165 complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required as in reinforcement and binding with MS wire (annealed) not less than 0.9mm dia complete all as specified and directed

S&F 0.50 mm thick TCT (total coated thickness) pre-coloured galvalume sheets with minimum base metal thickness of 0.45 mm, single skin high rib/multi rib profile galvalume sheeting having 1000-1020 mm width and 28-30 mm high crest @ maximum 250-255 mm pitch (centre) with sheets manufactured out of 0.50 mm this TCT (total coated thickness) high tensile galvalume sheets having tensile strength 550 MPA with 18-20 micron top coat over 5 micron primer and 8-10 micron alkyld backer zinc aluminium alloy AZ-150, sheets having a dip metallic zinc (43.5%0 aluminium (55%) & silicon (1.5%) with total mass coating of 150 gms/sqm on both sides, having wide pans with minimum 3 small stiffening ribs for effective water shedding and special male/female ends with full return legs on laps for purlin support and fixed as per existing profile of roof complete all as specified and directed.

M&L for pre-painted, galvalume aluminium zinc coating GI based plain steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20 mm graded aggregates in slabs supported on walls, beams and columns in floors, roof landings, balconies, canopies, deck slabs and in shelves etc complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20mm grade stone aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed (NOTE: MS reinforcement shall be measured and paid seperately)

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc for rough finished surfaces complete all as specified and directed

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (horizontal or sloping) for rough finished surfaces complete all as specified and directed.

S&F Factory made solid PVC door frame (chowkhat) of size 100 mm x 45mm made out of 5mm thick single side prelam PVC sheet, frame reinforced with MS square tube of size 40mm x 20mm of 19 guage throughout the frame, fixed in opening as per specification & drg as per manufacturer instructions complete all as specified and directed.

S&F 28-30mm thick factory made solid PVC moulded door shutter, with 2, 4, or 6 raised panel design with 2mm thick Moulded prelam PVC Sheet on the front face & 2mm plain prelam PVC sheet on back face, complete all as specified against clause 8B 4.1 of SSR Pt-ll and all as shown in product drawing on ser page No. 161 of SSR Pt-ll (2020) complete all as specified and directed.

S&F butt hinges, medium weight, stainless steel, 100mm complete all specified and directed

S&F 125mm extruded aluminium handles, fabricated type, anodised complete all specified.

S&F 150mm extruded aluminium handles, fabricated type, anodised complete all specified.

S&F 200mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all specified.

S&F 300mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all specified.

S&F 250mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all specified.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed.

S&F in repairs Chromium Plated 25mm dia brass chromium plated curtain rod with fixing brackets, stops, rollers etc complete all as specified and directed.

S&F in repairs fancy type metal finish curtain bracket fixed to walls complete all as specified and directed.

S&F PVC solid wall lining consisting of 5 mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per manufacturer’s specification and instruction and as directed.

S&F 5mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing.

M&L 10 mm thick rendering on fair faces of concrete surfaces in cement mortar (1:3) as on ceiling finishing concrete surfaces even and smooth without using extra cement complete all as specified and directed

M&L for rendering 15 mm thick to fair faces of brick work / concrete surface in cement mortor (1:6) finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 15 mm thick plastering in two layers, 10 mm + 5 mm in cement mortar 1:4, top layer of 5 mm thickness mixed with with water proofing compound (@ 200 ml per bag of cement or as per manufacturer's instructions) on brick/stone walls or concrete surfaces finished even and fair (upto any height) for external surfaces complete all as specified and directed. Note : Water Proofing compound shall be measured & paid seperately as "Supply only".

Supply only liquid Water Proofing Compound, conforming to IS and as approved, complete all as specified.

M&L for neeru finish to plastering with 1.5 mm thick lime putty, well finished with trowel complete all as specified and directed.

M&L for coloured glazed ceramic tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles and fixed over and including backing coat of 15mm thick rendering in cement mortar 1:3 complete all as specified and directed.

M&L for coloured non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over laid screed bed 15 mm thick cement mortar 1:4 complete all as specified and directed.

M&L for coloured non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over laid screed bed 15 mm thick cement mortar 1:4 complete all as specified and directed.

-ditto- but non-skid tiles in skirting, fixed over and incl 10mm thick rendering in cement mortar 1:3 complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40 mm graded stone aggregates as in sub base of floor, foundation filling etc complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C2 (using 40mm graded crushed stone aggregate) as in plinth protection, laid in alternate bays, finished even and smooth without using extra cement as directed by the Engr-in-Charge.

Forming construction joints 65 mm deep and 10 mm wide filled with bitumastic flooring with bitumen and sand proportion 1:2 complete all as specified and directed.

M&L for 25mm thick cement concrete type B-0, 1:2:4 using 12.5mm graded aggregate in sub bases of floors complete all as specified and directed.

M&L polythelene film, black, 150 micron, laid in floors complete all as specified and directed.

M&L for coloured glazed ceramic tiles in vertical surface 350x250/450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles and fixed over and including backing coat of 10mm thick rendering in cement mortar 1:3 complete all as specified and directed.

M&L for heavy duty ceramic floor tiles of size 300 x 300 x10mm thick in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed. (MAKE : JOHNSON, Model : Endura or equivalent product in other makes listed in the tender)

M&L for pre-polished Chequred cement concrete tiles (coloured) of size 30cmx30cmx22-25mm thick, set, jointed and pointed in neat cement slurry in floor and pointed with grey cement & pigment to match the surface laid over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed .

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old decorated surfaces of ceilings and applying one coat of white wash complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls and applying one coat of white wash complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls and applying with brush one coat of cement base paint complete all as specified and directed.

M&L for preparation of new plastered surfaces on walls and applying with brush two coats of cement base paint over a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of new untreated wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces exc 10 cm width or girth including preparation of surfaces complete all as specified and directed.

M&L for preparation of newly plastered surfaces and applying with roller two coats of exterior acrylic emulsion weather proof paint over a coat of primer to new wall surfaces of any description, over 10cm width or girth not otherwise described, as per manufactuirer's isntructions, upto 4 storey height complete all as specified and as directed.

M&L Preparing new plastered surfaces of Wall and applying with roller two Coats of acrylic bound distemper over one coat of alkali resistant primer complete all as specified and as directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, treating ends of posts, back of chowkhats etc, with tar or coal tar black paint, area tarred exc 0.1 sqm but n. exc 0.5 sqm each complete all as specified and directed.

-ditto- as per Item No. 86 above but treating small articles such as holdfasts, ends of posts, back of chowkhats, etc, area n exc 0.1 sqm each

Taking up or down steel water tubing 15 mm bore incl connections and removal from site complete all as specified and directed.

-ditto all as per item No 88 here-in-before but 20 mm bore

S&F tubes 15mm bore medium grade galvanised with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

-ditto all as per item No 90 here-in-before but 20 mm bore

-ditto all as per item No 90 here-in-before but 25 mm bore laid in trenches

S&F 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F stop valve cast copper alloy, screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or union for pipe 15mm bore, ISI marked complete all as specified and directed.

S&F Chromium plated brass Bib cock with wall flange, fancy type, long body, fixed to 15 mm bore of Iron pipe complete all as specified and directed. (Make : JAQUAR, Cat No: FUS-29037 / CERA, Cat No: F1015151/ ASIAN PAINTS, Cat No: ALBC101 / PRAYAG, Cat No: 9306-N/HINDWARE, CAT No: F360004 /PARRYWARE, Model: CLARET)

-ditto- but bib cock fixed in repairs

S&F Chromium plated brass Wall mixer, concealed type incl concealed body, with both overhead and telephone shower arrangement, fixed with 15 mm bore Iron pipe complete all as specified and directed. (Make : JAQUAR, Cat No : FUS-29281/ PARRYWARE, Cat No: G4817A1 / CERA, Cat No: F1003404 / ASIAN PAINTS, Cat No: ALWM104 / PRAYAG, Cat No: 9380-N / HINDWARE, Cat No: F390022) NOTE: Telephone shower shall be measured and paid seperately.

S&F fancy type chromium plated telephonic hand shower (ABS Body), multiflow type with flexible tube and hook screwed for iron pipe including frame complete all as specified and directed. (Make : JAQUAR, Cat No: HSH-1939 / CERA, Cat No: F7030103AB / ASIAN PAINTS, Cat No: HS-104 / HINDWARE, Cat No: F160050 / PRAYAG, Cat No: BHS-90 /PARRYWARE, Cat No: T9819A1 )

S&F 15mm bore chromium plated single lever central hole basin mixer (premium quality) without popup waste system with 450mm long copper pipe and brass nut, complete all as specified and directed. (MAKE : JAQUAR, Cat No: ARI-39001B / CERA, Cat No : F1005451 / ASIAN PAINT, Cat No: MYBM101 / HINDWARE, Cat No: F380009/ PRAYAG, Cat No: 8151 /PARRYWARE, Cat No: T3814A1)

S&F angle valve, 15 mm bore, cast copper alloy, chromium plated fancy type, concealed type with wall flange fixed to iron pipe complete all as specified and directed. (Make : PARRYWARE, Cat No: G4807A1 / JAQUAR, Cat No: FUS-29053 / CERA, Cat No: F1015361 / ASIAN PAINTS, ALAC101 / HINDWARE, Cat No: F360006 / PRAYAG, Cat No: 9010)

-ditto- but angle valve fixed in repairs

S&F Tubular towel rail, 20mm dia, 600 mm long, brass chromium plated, fixed with brass screws complete all as specified and directed. (MAKE : JAQUAR, Cat No : ACN-1111SM / PARRYWARE, Cat No : T6401A1 / / CERA, Cat No: F5004103 / HINDWARE, Cat No: F880005 / PRAYAG, Cat No: BA-20)

-ditto- but towel rail fixed in repairs

S&F Low density polythelene pipe connection, comprising of 15 mm dia 450 mm long having PTMT union at each end of connection to each of pillar tap/cistern/stop cock/urinal etc. at one end, stop cock at other end complete. (MAKE : PRAYAG, Cat No. 323 / POLYTUF, Cat No. 4003 / ESS ESS, Cat No: B2CH118 or equivalent model in SHAKTI / JEXON)

-ditto- but 450 mm connection pipes fixed in repairs

S&F Vitreous China table top Wash Basin 560 x 340 mm in size, White with 32mm dia Brass Chromium Plated Waste Fitting and 32 mm dia PVC waste pipe, making good disturbed Surfaces in Cement Mortar 1:3 complete all as specified and as directed. (MAKE : CERA, Model: CAYDEN / PARRYWARE, Cat No. C8845 / HINDWARE, Cat No. 10104 / JAQUAR, Cat No. FNS-WHT-40931)

S&F CP bottle trap with internal portion 32mm size with 190mm long wall connection pipe complete all as specified and directed (Make: JAQUAR, Cat No: ALD-769L250x190 / ESS ESS, Cat No: C-231C / HINDWARE, Cat No: F850003 / CERA, Cat No: F8060302/ PRAYAG, Cat No: BEA-26)

S&F vitreous china floor mounted rimless one piece closet (Pedestal pattern), white, including low level vitreous china valveless syphonic action type flushing cistern with inlet ball valve float, push button, flush pipe incl bracket, P/S trap, UF soft close seat cover and connecting fittings complete all as specified and directed. (Make : PARRYWARE, Model: Omega / HINDWARE, Model: SPELNDOUR / CERA, Model: CLOUD)

S&F 15 mm bore fancy type stop valves, cast copper alloy, chromium plated (concealed type), screwed down, high pressure, with crutch or butterfly handle, incl concealed body, screwed both ends for iron pipe or for unions and, complete all as specified and directed. (MAKE : JAQUAR, Cat No: CON-083FTK / PARRYWARE, Cat No : G1461A1 / ESS ESS, Cat No: T-108 / CERA, Model: OCEAN / PRAYAG, cat No: 9218/ HINDWARE, Cat No: F330052)

S&F Vitreous china, white, half stall urinal flat back with grating and union for discharge pipe (excl flush pipe and flushing cistern and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and Union for discharge pipe complete all as specified and directed. (Make of Urinal : CERA, Model: CARYS / HINDWARE, Cat No: CORTO / PARRYWARE, Model: Aquaseal N )

S&F 32 mm bore PVC urinal waste pipe, 800 mm long complete all as specified and directed. (Make: PRAYAG, Cat No: 3271 or equivalent make as approved by GE)

Supply, hoisting and fixing in proper position ISI marked multi-layer rotational moulded polyethylene water storage tank (cylindrical vertical with closed top), of capacity 1000 litres and providing necessary connections complete all as specified and as directed.

S&F 25 mm bore Ball brass valves, high pressure, with HDPE float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. (MAKE : PRAYAG, Cat No. B-153 or equivalent model in JEXON / POLYTUF / SHAKTI)

M&L granite (of any type) work, 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, urinal partition and like in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and making moulds on edges laid over and including 20 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

S&F 18-20 mm thick granite slab as in vertical surfaces, cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone incl grinding and polishing over and including 10mm rendering in cement mortar (1:3) completed all as specified and directed.

M&L for 100 mm thick cement concrete type B-2, 1:2:4 using 40mm graded aggregate in sub bases of floors complete all as specified and directed.

M&L for providing precast cement concrete (1:2:4) type B1 using 20 mm graded aggregates set in cement mortar 1:4 as in landings, cover slabs (for manhole etc.) chullah hoods, chajjas, water troughs, shelves and similar articles with plain faces complete all as specified and directed. (NOTE: MS reinforcement shall be measured and paid seperately)

S&F in repair stainless steel round floor trap 102 mm dia with waste hole complete all as specified and directed. (Make : PRAYAG, Cat No: FT-04 or equivalent make as approved by GE)

S&F in repair 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and incl with flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete all as specified and directed. (MAKE : PARRYWARE, Model : Slim line Economy / HINDWARE, Model : Sleek Plus / CERA, Model : Corona / PRAYAG, Model: SMART or equivalent model in COMMANDER)

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white and trap, including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc incl PVC seat cover complete all as specified and directed. (Make : Parryware, Model: Verve/CERA, Model: Celeb/HINDWARE, Model: Superb S)

S&F in repair chromium plated ABS body, round over head shower rose with arm (premium quality), multi flow, fixed to 15mm bore of iron pipe complete all as specified and directed. [Make : CERA, Cat No: F7040105 (arm) & F7020305CH (shower) / PARRYWARE, Cat No: T9802A1 (arm) & T9986A1 (shower)/ JAQUAR, Cat No: OHS-1789 (shower) & SHA-477(arm) /HINDWARE, Cat No: F160008(shower) & F330028(arm)]

S&F in repair Chromium plated brass Pillar tap, fancy type. with areator, fixed to wash hand basin, complete all as specified and directed. (Make : JAQUAR, Cat No: CON-021KN/ PARRYWARE, Cat No: G1402A1 / PRAYAG, Cat No: 9204/ HINDWARE, Cat No: F330002CP / Cera, Model: OCEAN)

S&F in repair Vitreous China Wash Hand Basin 550x400mm in size, Coloured, (Flat Back or Angle Back Type), making good disturbed Surfaces in Cement Mortar 1:3, providing CP waste coupling and PVC waste pipe including taking down/out unserviceable Wash Hand Basin and connected Items, complete all as specified and directed. (Make of WHB : PARRYWARE, Cat No. C0406 / HINDWARE, Cat No. 10010 / JAQUAR, Cat No. CNS-WHT-801 / CERA, Cat No: S2040141) (Make of Waste Pipe: PRAYAG, Cat No: 327 or equivalent make as spproved by GE) (Make of Waste Coupling: PRAYAG, Cat No: BEA-10 / JAQUAR. Cat No: ALD-705/ CERA, Cat No: F8050101)

S&F in repair Door closer hydraulically regulated, designation No. 3, universal type, aluminium (die cast) body, suitable for door shutters of 851 to 1000 mm in width & weight between 61 to 80 kg complete all as specified and directed.

S&F in repairs soap dish, chromium plated body complete all as specified and directed. (Make: PRAYAG, Cat No: BA-45 / CERA, Cat No: F5003106 / ESS ESS, Cat No : AC-503B / PARRYWARE, Cat No: T6902A1)

S&F in repairs Stainless steel kitchen rack of size 31" x 24" x 10" fixed in wall with screws and washer complete all as specified. (MAKE:- PRAYAG , Model No- P-340 or equivalent model in SUYOG / BLUE STAR / ANUPAM INDUSTRIES)

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete al as specified and directed. (MAKE: HINDWARE, Cat No: F880010 / JAQUAR, Cat No: ACN-1171N / PARRYWARE, Cat No: T6009A1 / PRAYAG, Cat No: BEA-51 / CERA, Cat No: F5001114)

S&F in repair sinks with drainage board made of stainless steel 1 mm thick in kitchen with plug washers, waste coupling, PVC waste pipe and fixing cantilever brackets connecting union to pipe, overall size of sink 914 mm x 460 mm and bowl size 405 mm x 354 mm x 203 mm complete including taking down existing sink complete all as specified and directed. (MAKE : PRAYAG, Cat No. 1239-D or equivalent model in NIRALI / DIAMOND / ANJALI / JAYNA / BLUE STAR / CERA / PARRYWARE)

S&F 100 mm dia CI floor/nahani trap, with grating including jointing to waste pipe, fixed in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregates complete all as specified and directed.

S&F Salt-gauged stoneware gully traps, square or round mouthed, type 'P', size 150x150 mm complete all as specified and directed.

S&F Cast iron (sand cast) soil, waste and vent pipes 100 mm bore of any length with or without ears with cement joints all as specified laid in trenches or in floors complete all as specified and directed.

S&F CI bends for 100mm pipe (any radius) diminishing piece or tapers (large bore measured) complete all as specified and directed.

S&F 100 mm bore cast iron (sand cast) bends with access door (any radius), diminishing pieces or tapers (larger bore to be measured) complete all as specified and as directed.

S&F CI branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parellel branches, for 100mm dia pipe complete all as specified and directed.

M&L for 150mm dia bore of reinforced concrete pipes, class NP3, laid and jointed complete with collars complete all as specified and directed.

M&L for reinforced concrete pipe 900 mm dia class NP3, laid and jointed with jute & cement mortar 1:2, complete with collars all specified and as directed.

M&L for cement concrete 1:3:6 type C-2 in concrete bed to 150mm dia drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in complete all as specified and directed.

M&L for Concrete bed to drain pipes 900 mm bore including packing under and hunching against the sides the pipe after there laid and tested in cement concrete (1:3:6) type C2 using 40mm graded aggregate complete all as specified and as directed

M&L for laying pre-polished 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed. (NOTE: Cost of sand cushioning is deemed to be included in the quoted rates)

SCHEDULE 'A' PART-II (INTERNAL ELECTRIFICATION WORKS) Taking down copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceilling roses, pendants, regulators, sockets etc excluding light fitting for reuse or removing from site and making good disturbed surface of walls, floors etc.complete all as specified and directed.

M&L for concealed type point wiring with 1.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and including PVC conduit complete with all fittings and accessories, fixed to walls/ceiling, including mild steel terminal boxes 1.25 mm thick conforming to IS-5133 (Part-I) with 3.0 mm thick plastic laminated sheet top cover (ISI Marked) for mounting switches/ regulator /bell push etc and including 1.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly, for one light point /bell point/ ceiling fan/exhaust fan point controlled by one way switch complete all as specified and directed. (NOTES: - (i) Where tube light fitting is to be fitted/suspended, CI Circular boxes shall be provided with the PVC Pipes in the ceiling & the unit rate shall be deemed to be included for the same. (ii) Cost of cutting chases for concealed wiring shall be deemed to be inclusive in the quoted rates. No claim in this regard shall be entertained at a later stage)

All as per item No. 141 above but for one 5 amps switch socket outlet on same board controlled by another switch, complete all as specified and directed (concealed type point wiring with terminal box).

All as per item No. 141 above but for one 5 amps switch socket combination on independent board, complete all as specified and directed (concealed type point wiring with terminal box).

All as per item No. 141 above but using 2.5 sqmm single core multi stranded copper conductor FRLS-H PVC insulated and unsheathed, cable for 3/6 pin 15 Amp socket outlet controlled by one switch on independent board with and incl 2.5 sqmm green FRLS-H PVC insulated and unsheathed, copper conductor as continuous earth wire with lugs complete all as specified and directed (concealed type point wiring with terminal box).

M&L for concealed type point wiring with 1.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core, laid in and incl PVC conduit complete with all fittings and accessories (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches/ regulator /bell push etc and including 1.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core, earth continuity conductor connected to common earth dolly for One light point or one fan point or bell point controlled by one switch or bell push complete all as specified and directed. (NOTE :- (i) Where tube light fitting is to be fitted/ suspended, CI Circular boxes shall be provided with the PVC Pipes in the ceiling & the unit rate shall be deemed to be included for the same. (ii) Quoted rate shall be exclusive of the cost of terminal box & laminate cover which shall be measured seperately. (iii) Cost of cutting chases for concealed wiring shall be deemed to be inclusive in the quoted rates. No claim in this regard shall be entertained at a later stage)

All as per item No 145 here-in-before but for one 5 pin 5/6 amp socket out let point in the same switch board of light points (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches

All as per item No 145 here-in-before but for one 5 pin 5/6 amps multisocket outlet point in independent board (concealed wiring) (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches

All as per item No 145 above but using 2.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed, multi stranded copper conductor cable 1100 Volts grade, single core for line conductor and 2.50 Sq. mm (nominal area) FRLS-H PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade, single core for earth continuty wire for one 15/16 amp multi socket out let independent. (concealed wiring) (except terminal box and laminate cover), fixed to walls/ceiling, for mounting MODULAR TYPE switches

S&F switch piano flush button AC 230 V Single pole 5/6 Amp one way complete all as specified and directed.

S&F socket outlet 2-in-1, 3 pin, 6 Amp AC 230 Volts flush type complete all as specified and directed.

S&F switch socket combination, 5 pin, 6 Amp AC 230 Volts flush type complete all as specified and directed.

S&F switch socket combination 2 in 1, 3 pin, 6 and 16 Amps flush type universal complete with all necessary electrical connection all as specified and directed.

S&F ceiling rose surface, polycarbonate/bakelite, three terminals complete all as specified and directed.

S&F Modular Switch 1 way, 6 Amps, 1 module complete all as specified and directed.

S&F Modular Switch 1 way, 16 Amps, 1 module complete all as specified and directed.

S&F Modular Socket 6 Amps, 2/3 pin combined, 2 module complete all as specified and directed.

S&F Modular Socket 6/16 Amps, 2/3 pin combined, 2 module complete all as specified and directed.

S&F Modular Fan step regulator, 120 watt, 2 module complete all as specified and directed.

S&F Modular Blank plate, 1 module complete all as specified and directed.

S&F Modular White cover plate with frame 3 module complete all as specified and directed.

S&F Modular White cover plate with frame 4 module complete all as specified and directed.

S&F Modular White cover plate with frame 6 module complete all as specified and directed.

S&F Modular White cover plate with frame 8 module complete all as specified and directed.

S&F Modular White cover plate with frame 12 module complete all as specified and directed.

S&F Modular type Metal Flush box 3 module complete all as specified and directed.

S&F Modular type Metal Flush box 4 module complete all as specified and directed.

S&F Modular type Metal Flush box 6 module complete all as specified and directed.

S&F Modular type Metal Flush box 8 module complete all as specified and directed.

S&F Modular type Metal Flush box 12 module complete all as specified and directed.

S&F surface mounted LED luminaire, 1 X 20 Watt in polycarbonate housing, 110 lumen/watt lumen efficacy, operating voltage 180-270 V, with acrylic/polycarbonate difuser & integrated constant current electronic driver complete with all other accessories internally prewired and including connecting up with three core flexible copper wire of suitable size complete all as specified and directed.

SF&F surface mounted slim-fit downlighter, 100 lumen/watt efficacy, round or square, having glare free frosted diffuser, operating voltage 180-270V, with constant current electronic driver complete with all accessories with and including 18 Watt LED and including all accessories, mounting frame etc and connecting up with three core flexible copper conductor wire of adequate size complete all as specified and directed.

Taking down of old Submain wiring any type including batten/ conduit/ casing at any indicated situation complete all as specified and directed.

M&L for sub main wiring with 2 runs (P-N) of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4.0 sqmm 1100 volts grade along with one run of FRLS-H PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 4 sqmm 1100 volts grade as earth continuity conductor drawn through and including adequate size PVC non-metallic concealed conduit complete all as specified and as directed. (NOTE : Three runs of single core 4.0 sqmm cable and one run of PVC conduit shall be measured as one unit)

M&L for cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing or concealed water tubing or concealed conduit wiring etc and making good, cutting not exc 10 cm girth complete all as specified and directed.

Taking down of Old MCB DB any type any size including MCCB/RCCB/MCBs and disconnecting the serviceable MCBs and keeping in safe custody for reuse at site or removal from site complete all as specified and directed.

S&F TPN DB, IP 43 protection, double door (premium range), 415 volts, 4 way (8+12), with 100 Amps copper bus bar for each phase complete all as specified and directed. (MAKE : L&T, Cat No. DBTPN004DD / LEGRAND, Cat No: 507670 / SCHNEIDER, Cat No. A9HTND04 / ABB, Cat No: E-SHDB M4 / PANASONIC, Cat No: BQS 304H / HAGER, Cat No: VYT04DH)

S&F SPN DB, IP 43 protection, double door (premium range), 240 volts, 4 way, with 100 Amps copper Bus Bar complete all as specified and directed. (MAKE : L&T, Cat No. DBSPN004DD / LEGRAND, Cat No: 507610 / ABB, Cat No. E-SHC M4 / SCHNEIDER, Cat No. NBKRENSNDD04 / HAGER, Cat No: VYS04D)

S&F Double Door, Sheet Metal Enclosure for DBs (premium range), for mounting of MCB for 240 Volts, 8 way, with 100 Amps rated copper bus bar, Single Pole & Neutral, complete all as specified and directed. (MAKE : L&T, Cat No. DBSPN008DD / LEGRAND, Cat No: 507611 /ABB, Cat No. E-SHC M 8 / SCHNEIDER, Cat No. A9HSND08 / HAGER, Cat No: VYS08D)

S&F MCB (premium range), 'C' series, TPN, 415 volts, 63 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)

S&F MCB (premium range), 'C' series, SPN, 40 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)

S&F MCB (premium range), 'C' series, SPN, 32 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)

S&F MCB (premium range), 'C' series, single pole, 6 to 32 Amps, breaking capacity 10KA complete all as specified and directed. (MAKE : L&T / LEGRAND / SCHNEIDER / ABB / PANASONIC / HAGER)

Materials and Labour for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanized steel earth wire 4 mm dia (upto 7.5 metres) by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 45 cm x 45 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 40 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and all as shown in Figure 15A of IS 3043 :1987, including necessary testing complete all as specified and directed.

S&F LED Street Light fitting, 35 watt capacity, lumen efficacy 120 lumen/watt, in high pressure die cast aluminium housing with prismatic polycarbonate modular secondary lens optics with integrated constant current electronic driver, top opening driver cover, IP66 ingress protection, impact resistance of IK07 complete all as specified and directed.

S&F Bracket/Arm suitable for street light fittings, made out of 32 mm bore (light grade) GI pipe length not exceeding 1.20 metre long, fixed with 02 sets of flat iron clamp of size 25mm x 5 mm, with bolts, nuts and washers of suitable size including applying two coats of aluminium paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Supply, installation, testing and commissioning of heater water storage type electric geyser (vertical cylindrical type) 25 ltrs capacity with BEE 5 star rating (min) and ABS body, glass lined/titanium enamel coated inner tank incl fixing arrangement with providing incl suitable capacity flexible cable 3 core with 3 pin plug of 16 amp and 02 Nos chromium plated brass connector pipe 15mm dia, 600 m long with brass coupling and union at both ends complete all as specified and directed. (Make: RACOLD, Model - CDR DLX / AO SMITH, Model- HSE-VAS / Havells, Model: Monza Dx / BAJAJ, Model: CALDIA)

S&F ventilating fan 250 mm sweep, with louvre shutter and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 Sq mm, 3 core, 1100 Volts grade, from ceiling rose to fan complete all as specified and directed. (MAKE : HAVELLS, Model : Venti Air DX / CROMPTON, Model : Brisk Air / HALONIX, Model: HELION DX / USHA, Model: CRISP AIR or equivalent model in BAJAJ / ORIENT)

Supply, Laying and testing XLPE insulated, screened PVC bedded, galvanised steel strip or wire armoured electric power cable 1100 Volts grade with stranded aluminium conductor of size 10 sqmm 4 core, laid in trench or fixed to wall/passing through pipe/pole complete all as specified and directed.

S&F PVC cable tray of size 54x50mm, 16 gauge with all accessories complete all as specified and directed.

SCHEDULE 'A' PART-III (EXTERNAL WATER SUPPLY) S&F galvanised tube, medium grade, 40mm dia with necessary fittings complete laid in trenches complete all as specified and as directed.

S&F GI tubing medium grade with all fittings and fixture complete to be fixed or laid on wall, duly clamped all as directed for 25mm bore pipe.

S&F gun metal gate or globe valve, with iron wheel head, screwed both ends for iron pipe and fixed for 40 mm bore pipe complete all as specified and directed.

S&F gun metal gate or globe valve, with iron wheel head, screwed both ends for iron pipe and fixed for 25 mm bore pipe complete all as specified and directed.

Drilling and tapping cast iron/GI water mains (in position) for branch connections for 40 mm internal dia complete all as specified and directed.

UNITED ENGINEERS

MS HORIZEN

UNIVERSAL TRADING CENTRE

PRABIR TRADERS

MARUTI ENTERPRISES

DEB AND COMPANY

GHOSH ENTERPRISE