REPAIRS WOODEN ALUMINIUM STEEL JOINERY UNDER C2A AND C2B AREA AND REPAIR MAINT OF INTERNAL ELECTRIFICATION INCLUDING MCB DBS BLDG STREET LIGHT AND CONNECTED WORKS UNDER GE(E) MATHURA

Amount

M&L for preparation of old decorative surfaces and applying one coat of oil bound distemper on wall surfaces complete all as specified and directed by Engr-in-charge

M&L for preparation of old surfaces of wall and applying one coat of whitewash complete all as specified and directed.

M&L for Preparation of old plastered surfaces of celling and applying one coat of white wash complete.

M&L for preparation of old wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

M&L for preparation of old steel surfaces over 10cm width or girth not other wise described and applying one coat of synthetic enamal paint complete all as specified & directed by Engr-in-Charge.

M&L for preparation of old painted concrete surface and applying one coat of synthetic enamel paint all as specified & directed by Engineer-in-Charge

Taking down chowkhats or frame with shutter (without taking off shutters from the frame) area n.exc. 1.50 Sqm each and making good the disturbed surface complete all as specified.

Taking down Chowkhats or frames exc 1.5 sq. m but n exc 4 sq. m each and making good the disturbed surface complete all as specified.

S&F Pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary fixing lungs, hinges, lock strike plate, etc, with a shop coat of red oxide primer complete all as specified.

M&L cement concrete M-10 grade (Nominal mix) using 12.5mm graded stone aggregate as in bed blocks for fixing hold fasts and fillling of chowkhats etc. all as specified.

Cutting holes in existing wall or PCC Block masonry built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfast and making good dismantled portion in cement mortar 1:3 or cement concrete M-15 grade (Nominal Mix) )using 20 mm graded stone aggregate required for filling of holdfast or lugs measured from the face of jamb into the wall exceeding half brick but not exceeding one brick all as directed.

S&F 35 mm thick flush shutters solid core construction with block board core and plywood fresh panel veneered type on both the side complete all as specified and directed by Engr-in-Charge.

S&F 30 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges offraming plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats

S&F solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforcement with MS square tube supplying and fixing in opening as per specification & sketch shown in sketch 8 of SSR part II.

S&F Factory Made Solid PVC Moulded Door Shutter with particle board core 28 to 30 mm thick (stiles), with 2, 4, or 6 raised panel design with 2 mm thick Moulded PVC Sheet on the front face & 2 mm plain colour PVC sheet on back face, with Particle board core, supplying & fixing in the frame at site as per specification & sketch shown in section 8 of SSR part II.

S&F 200mm long Aluminium anodised, handles, cast type, extruded section.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

S&F 150 mm long aluminium anodised handle fabricated type all as specified and as directed by Engineer-In-Charge.

S&F in repair100 mm Stainless steel butt hinges medium weight, cold rolled all as directed.

S&F 125mm long hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21

S&F in repairs two legged aluminum floor door stopper with rubber shoe 150 mm long complete.

S&F 5.5 mm Sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane

S&F 5 mm frosted glass,ordinary quality and glazing with rubber beading in square exc 0.5 sq. m in each pane

S&F in repairs sheet glass assembly consisting of 5.5 mm thick sheet glass shelf tinted glass ordinary quality and in square n.exc 0.5sqmm in each pane complete.

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded fixed to wall with one shop coat of redoxide primer complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded fixed to wall with a shop coat of red oxide primer complete all as specified and directed.

Dismandling of mild steel work of any description not other wise provided for.

S&F in repairs. 4mm thick sheet glass ordinary quality exc 0.50Sqm but not exc 1.00Sqm each pane including necessary cleats, glazing clips rubber packing, anodised aluminium snap beading, screws in aluminium windows complete.

S & F in repairs 3 mm thick pin headed/figured/frosted glass ordinary quality and glazing with oil putty/wooden beading in square n.exc. 0.5 sqm in each pane and complete.

M&L for spot welding for repairing steel windows and ventilators hinges, brackets, steel handle, etc. all as sepcified and directed.

S&F in repairs for MS Butt hinges cold rolled mild steel meadium weight fixed to MS pressed steel chowkhats including necessary welding and making good of damaged portion etc. all as sepcified and directed.

S&F in repair Aluminium die cast body Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg complete.

S & F 18 mm thick Rajshri solid PVC Kitchen PVC Sheet one side prelam sheet kitchen cabinet shutter of density 600 kg/cum bent at 90 degree and finish all edges at level for making edge lipping/bending or 0.5 mm thick PVC sheet lipping at all four edges using bonding lape etc complete as per direction of Engineer in charge Manufacture's specification. Make :- RAJSHRI PLASTIWOOD LTD/SINTEX INDUSRIES LTD/DURGA PLAST EXTRUSION

S&F Factory made PVC Cabinet of required size fabricated by joining 12 mm thick PVC celuka ply fixed with each other using solvent cement fixed with screw and solvent cement adhesive etc. complete as per specifications and as directed by the engineer - in -charge.

S&F 18mm thick factory made PVC shelf/ partion of required size consisting of panel of celuka PVC ply and for supporting the hold of shelf /partion and shall provided 3 edges in size18 mmx 18mm as per required lengththe front side of the edge visible in the front of the shelf /partion to be edge lipped by 18 mm widthx1mm thick PVC sheet of density 600 kg/cum manufactured by complete by direction of Engr-in-charge. Make :- RAJSHRI PLASTIWOOD LTD/SINTEX INDUSRIES LTD/DURGA PLAST EXTRUSION

S&F Magnatic catcher (KTS-20) full extension load capacity 8 kgs, Make-KAFF/Godrej/Hettich

S&F stainless steel handles 100 mm size for kitchen cabinet shutters Make-KAFF/Godrej/Hettich.

S&F extruded stainless steel handles 150 mm size for kitchen cabinet shutters Make-KAFF Godrej Hettich.

S&F auto closing hinges 35 mm of 0 crank( KH-001)OR 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters Make-KAFF/Godrej/Hettich

S&F stainless steel Tower bolt 150 mm size for kitchen cabinet shutters. Make-KAFF/Godrej/Hettich

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised

S & F chrome plated stainless steel wire basket (plate basket) pull out type, size 380 to 610 mm with necessary fixing clips etc. complete in all respect as specified and as directed by engineer- in – charge.

S & F chromium plated stainless steel wire basket (Thali basket) pull out type, size 380 to 610 mm with necessary fixing clips etc. complete in all respect as specified and as directed by engineer- in – charge.

S & F chrome plated stainless steel wire basket (cutlery basket) pull out type, size 380 to 610 mm with necessary fixing clips etc. complete in all respect as specified and as directed by engineer- in – charge.

S & F chrome plated stainless steel wire basket (Grain Trolley) pull out type, size 380 to 610 mm with necessary sliding frame structure, fixing clips etc. complete in all respect as specified and as directed by engineer- in – charge.

S & F chrome plated stainless steel wire basket (storage basket) pull out type, size 380 to 610 mm with necessary fixing clips etc. complete in all respect as specified and as directed by engineer- in – charge.

S & F chrome plated stainless steel wire basket (Bottle pull out) pull out type, size 100 to 150 mm with necessary sliding frame structure, fixing clips etc. complete in all respect as specified and as directed by engineer- in – charge.

Dismantling wall and ceiling boards (fiber, pulp, insulation, etc) or insulation board/slabs/blankets, any thickness, including cover fillets.

Providing and fixing inter locking metal grid (snap grid for false ceiling) of size 605 mm x 605 mm in true horizontal level, hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24 mm X 38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200 mm x 600 mm and secondary cross “T” of length 600 mm and size 24 mm X 28 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200 mm X 600 mm panel to form grids of 600 mm X 600 mm and wall angle of size 24 mm X 24 mm X 0.4 mm. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 mm X 37 mm X 25 mm X 1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 mm X 30 mm X 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications and as directed by Engineer-in-charge.

M&L for 4 mm thick designer non-asbestos fibre cement building board having fire resistance & moisture resistance properly. Make :- Everest, fixed on aluminium grid with screws complete all as specified and directed.

S&F in repair aluminium door shutter any size dismantiling stiles and rails refixing the same using same materials including glass sheet and partical board sheet with replacement of 6mm dia GI full screw to full width of shutter bolts 2 Nos one at each top and bottom with necessary cleats using screws and nuts etc. complete all as specified and directed by Engr-in-charge.

S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick Aluminium alloy sheet foundation box, main body with stainless steel cover, groverning pivot made of brass, other parts made of mild steel heavy duty made and fixed complete all as specified .

Dismantling asbestos cement corrugated or semi corrugated sheets in roof covering incl ridge.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering fixed with self tapping screws complete.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in cladding to wall, fixed with self tapping screws as specified.

Dismantling timber scantlings (framed work) exc 40 Sq Cm in section, in any position.

M&L for Mild steel work in tubular trusses, purlins, vetical posts including special shaped washer, angle cleats, fish plates, gusset plates, base/ bearing plates, bolts and nuts etc. complete using ERW or induction butt welded tubes conforming to 1161-1979 grade st 240.

M&L for 12 mm thick plain / Frosted tuffened end glass wired type on opening and shelfis / portion including cutting and grooving on wall with or with out aluminium frame ,rail handle lock ,etc including floor machine complete.

Taking down and re-fixing of old aluminium shutter Re-securing, repair locking arrangement, floor spring, bottom and top pivot adjusting in same opening place in shutters of any description exc 1.5 Sqm and n.exc 4 Sqm each

Taking down and re-fixing of old aluminium shutter Re-securing, repair locking arrangement, bottom, top and side rail adjusting in same opening place in shutters of any description n.exc 1.5 Sqm each

Taking down and re-fixing of 12mm thick toughen glass after repairing of hardware fittings (Handle, Lock, floor spring, bottom &Top pivot ), frosted as per design approved by Engineer-in-Charge / GE.

S&F in repair 100 mm size mortice lock of brass, vertical type,4 levers, complete all as directed.

Supply fabricate & fix in position aluminium powder coated (Powder coating shall not be less than 50 micron of approved colour) three track window ( two shutters glazed & one shutters wiregauge) with frame, glazed with 4 mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing in position, concelled type lock for all three shutter, PVC roller etc all as specified below, including taking down old window complete all as specified and directed. (a) Frame (top & side) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 20831) (b) Frame (bottom) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 20832) (c) Top & side Members of shutter Section shall be be of size 18.00 x 40.00 x 1.55 (Section No 20738) (d) Shutter Interlock Section shall be be of size 18.00 x 40.00 x 1.45 (Section No 20737) (e) Bottom Members of shutter Section shall be be of size 18.00 x 40.00 x 1.55 (Section No 20736) (f) Member for wire gauge shutter shall be 18.00 x 43.50 x 1.35 (Section No 20791). Note:- Section No given above are of make Jinal, or eq Note:- (i) Section No given above are of make Jindal, Contractor may use similar section of other make mention in Appx B (ii) Floor door spring & lock will be measured & paid separately.

Supply & fix in position aluminium powder coated (Powder coating shall not be less than 50 micron of approved colour) door shutter with frame, partly glazed with 5 mm thick tinted glass and partly panelled with 9 mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150 mm size, aluminium barrel tower bolt 200 mm size etc all as specified below complete all as specified and directed. (a) Frame (top & side) section shall of size 101.60 x 44.75 x 2.4 mm ( Section No 14021) (b) Vertical Members of shutter Section shall be be of size 85.00 x 44.45 x 2.00 mm (Section No 19560) (c) Top Members of shutter Section shall be be of size 83.50 x 44.45 x 2.00 mm (Section No 19581) (d) Lock rail (Middle member) of shutter Section shall be be of size 150.00 x 44.45 x 3.00 mm (Section No 19596) (e) Bottom Members of shutter Section shall be be of size 150.00 x 44.45 x 3.10 mm (Section No 19584) (f) Glazing clip for securing glass of shutters shall be be of 0.80 mm thick (Section No 19370). Note:- (i) Section No given above are of make Jindal, Contractor may use similar section of other make mention in Appx B (ii) Floor door spring & lock will be measured & paid separately.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in position. Make:- Godraj / Sandhu / Everest

S&F Mortice lock vertical type of mild steel 4 levers of size 100mm all as specified. Make : Godrej, ozone or equivalent.

Providing and fixing factory made UPVC white colour sliding window three track made of extruded profiles with wall thickness of 2.3mm(0.2 mm ).Windoow profile with hollow section with multi chamber.Frame (88 mm x 52 mm),sliding sash (42 mm x 67 mm ).Sliding mesh Sash (42 mm x 57 mm) Slide interlock (One vertical length in each shutters )(45.5 mmx 28 mm ),Glazing bead (24.5 mm x 16 mm) will be mitered cut and fusion welded at all corners,including railing of holes for fixing hardware and drainage of water etc. making arrangement for fising of hardware.EPDM gasket 1.2 1-0.2 mm thick galvanized steel frame (30mmx18 mm) 2 No.s ,sliding sash(30 mm x 18 mm),sliding mesh sash (26 mmx 10 mm) profile to be inserted in required profile ,frame will be fixed to wall with 8 mmx100 mm long fasteners.HardwareTouch lock of zinc alloyed (white powder coated ),steel roller system ,stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and required accessories .(Note:The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories.Net opening will be measured for payment purpose.)Area n exc 2.00 Sqm Each

Taking down 12 mm thick toughen glass door shutter area exc 2 Sqm but n.exc 4 Sqm each, adjustment, greasing & oiling of floor door spring refixing the door in same opening and making the door for smooth function complete all as directed.

S&F aluminium (Powder coating shall not be less than 50 micron of approved colour) ventilator, partialy glazed and partialy louvers, outer frame & mullion fabricated with aluminium section of size 82.50 mm x 38.00 mm x 1.70 mm thick (Cat No 20036), half portion glazed with 4 mm thick frosted glass including rubber beading, & glazing clip, half portaion louvers of 80 mm wide & 4 mm thick frostade glass including aluminium louver patti including S.S wire gauge of fixing of 0.36mm dia and 1.40 width of aparture with 25x3mm think aluminium strip with screw to upper half portion of ventilator all fitting & fixture and fixed in position including taking down old ventilator complete. Note:- (i) Section No given above are of make Jinal,

S&F in repair stainless steel lock fixed to toughen glass door shutter, horizontal type, 4 levers, complete all as directed. Make:- Godrej, ozone or equivalent.

S&F door seal botom, door air gap, rubber shield 94cm anti rust type and black rubber all as specified and directed by Engr-in-Charge

Taking down carefully aluminum/copper point wiring (light ,fan, socket any type, power, bell etc. ) complete including fixtures & fittings (such as ceiling rose, socket, Pendent, regulator, etc) and removing the material from site and making good the disturbed surfaces of walls ceiling etc complete all as directed. Note: Credit for above items shall be made as per schedule of credit.

Taking down carefully by Submain wiring of any type complete and making good disturbed sufaces to match with the existing surfaces all as directed by Engineer-in-Charge.

Taking down old unserviceable existing SPN/TPN DBs / enclousers any size and type / any descriptions as iron sheet scrap and making good disturbed surface / wall as per existing complete all as specified and directed

M & L for Point wiring with 1.5 Sqmm (nominal area) single core PVC insulated unsheathed (FRLS) cable, multi-stranded, copper conductor, in universal colour code with & including suitable size of rigid non-metallic PVC conduit (not less then 20mm dia medium grade) and its all accessories complete concealed in wall incl cutting & chases( making good all to the disturbed surfaces as per existing) and modular flush metal boxes including cover plate with frame for mounting modular switches, sockets, regulators,socket etc including earth wire of PVC insulated (FRLS) copper conductor multistranded of 1.5 Sqmm size in green colour complete all as specified in current SSR Part-I & II & directed by the Engineer-in-Charge , as described below:-

One light/ fan point controlled by one way switch 5 amp complete.

One 3 pin 5 Amps socket point controlled by one way switch on same board.

One 3 pin 5 Amps socket point controlled by one way switch on independent board.

One bell point controlled by one push button on independent board.

One light point controlled by two 2-way switches.

All as per item No. 77 here-in-above but 3pin/5pin 16Amps Socket point controlled independently with 4 Sqmm PVC insulated & unsheathed (FRLS) copper conductor cable independent Point wiring complete all as specified and as directed .

All as per item No. 77 here-in-above but for 20 Amps of AC enclosure independent, with 4 Sqmm PVC insulated & unsheathed (FRLS) copper conductor cable independent Point wiring complete all as specified and as directed .

Supply and Fixing Modular switch 6 Amps single pole one-way, 1 Module complete all as specified.

Supply and Fixing Modular bell Push switch 6 Amps with indicator single pole one-way, 1 Module complete all as specified.

Supply and Fixing Modular switch 16 Amp single pole one way,1 Module all as specified. Make: Cat part No AHFSXXW161 of havells or equivalent.

Supply & Fixing Modular fan Regulator electronic step type, 2 Module complete all as specified.

Supply and Fixing Modular socket 2-in-1, 5 pins 6 Amps , combined 2 Module complete all as specified.

Supply and Fixing Modular socket 2-in-1,3 and 5 pins 6 /16 Amps, combined 2 Module complete all as specified.

Supply and Fixing Modular switch 6 Amps single pole two-way, 1 Module complete all as specified.

S&F switch piano type , SP, one way, flush type 5 Amps complete all as specified.

S&F socket out let 2 in 1 flush type 5 pin 5 Amp complete all as specified.

S&F socket out let 2 in 1 flush type 3 pin 5 & 15 Amp complete all as specified.

S&F switch piano flush type 15 Amp, SP, 240 volt, one way complete all as specified.

S&F bell push siwtch piano flush type, SP, one way, 5 Amps complete all as specified.

Supply and Fixing ceiling rose surface bakelite 65mm x 50mm three terminals complete all as specified..

Supply and fixing lamp holder, PVC / polycarbonate type with back plate suitable for batten fittings complete all as specified.

Supply and fixing Bell Multi Music type, 230 Volts complete with connection all as specified & directed.

Supply and fixing Bell Ding dong type, 230 Volts complete with connection all as specified & directed.

S&F fan Regulator electronic step type complete all as specified.

M&L for Sub Main Wiring with two runs single core 4Sqmm PVC insulated unsheathed FRLS cable with stranded copper conductor drawn in suitable size of rigid non-metallic PVC conduit and its all accessories complete concealed in wall/roof with and including 4 Sqmm copper green colour earth wire all as specified and directed by Engineer-in-Charge. Note :- Two run of 4 Sqmm single core cable, one run of 4 Sqmm earth wire & one run of PVC conduit will measured as one unit length.

M & L for Sub Main Wiring with two runs single core 6 Sqmm PVC insulated unsheathed (FRLS) cable with multistranded, 1100 volts grade copper conductor drawn in suitable size of rigid non-metallic PVC conduit (not less then 20mm dia med gd) and its all accessories complete concealed in wall/roof incl cutting & chases( making good all to the disturbed surfaces as per existing) with and including 6 Sqmm copper green colour earth wire all as specified and directed by Engineer-in-Charge. Note: Two runs 6 Sq mm one run of 6 Sq mm earth wire & One run of PVC conduit shall be measured as one unit length.

Disconnect and remove unserviceable capacitor and supply and fix capacitor 2.5 to 3.5 MFD suitable for ceiling fan/ exhaust fan complete all as specified and directed.

Supply & fixing indoor decorative ultra slim surface /Wall mounted LED batten tube light complete fitting 1x 20 watt LED Tube fitting with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts,co- related colour temperature (CCT) of 6500K, >100 Lm/Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Enginee-in-Charge.

Supply & fixing indoor decorative ultra slim surface /Wall mounted T5 LED batten tube light complete fitting 1X9 watt LED Tube fitting (size within 600x25x40 mm) suitable for mirror light with polycarbonate channel housing & integrated electronic driver,energy efficient, 140V-270 volts,co- related colour temperature (CCT) of 6500K,>100Lm/Watt complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Enginee-in-Charge.

Supply & fix surface mounted bulk head LED light fitting including 10 watt LED lamp B22 base complete with all accessories and connection complete all as specified and as directed.

Supply and fix LED 9 W suitable for normal holder (Base Cap B22), warm white/ cool white/natural white complete all as specified.

Supply and fix LED 7 W suitable for normal holder (Base Cap B22), warm white/ cool white/natural white complete all as specified.

Supply and install of 30W LED building security light fitting with lens & driver, powder coated pressure die cast aluminium, top opening and maintainable with heat resistance toughened glass, built-in Short-Circuit Protection, Over voltage Protection and Surge Protection, IP-65 proction with luminaire efficiecy of greater than 80Lumen/Watt, Colour rendering (CRI) of ≥ 70 and co- related colour temperature (CCT) of 5700K (±500K) . The luminaire should have 10 KV surg protection, PF ≥ 0.9 and total harmonic distortion of THD ≤ 10%, voltage range of 140-280V including all connections complete all as specified.

Supply & fix in repair recess type, 30 watt LED panel light (600x600 mm) complete with fittings integrated electronic driver,energy efficient, 230 volts,co- related colour temperature (CCT) of 6500K, warm white/ cool white/natural white complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed by Enginee-in-Charge.

Supply and fix LED 9W, suitable for E27 type holder warm white/ cool white/natural white complete all as specified.

S&F LED Round/square recess mounted slim downlighter 6 watt, integrated electronic driver, co- related colour temperature (CCT) of 6500K, warm white/ cool white/natural white complete all as specified.

S&F LED Round/square recess mounted slim downlighter 12 watt, integrated electronic driver, co- related colour temperature (CCT) of 6500K, warm white/ cool white/natural white complete all as specified.

S&F LED Round/square recess mounted slim downlighter 18 watt, integrated electronic driver, co- related colour temperature (CCT) of 6500K, warm white/ cool white/natural white complete all as specified.

M&L for building security light bracket made out of 40mm dia medium grade GI pipe of 1.2 m length bent to required shape suitable for fixing street light fitting on Steel tubular pole including two Nos clamps made out 40mm X 6mm flat with suitable nuts and bolts including two coats of aluminium paint over a coating of red oxide primer complete all as directed taking down old unserviceable bracket as scrap any size / description.

S&F MCB distribution board, SPN 12 Way, Double door, sheet steel, phosphatised, powder painted with bus-bar 200Amp, neutral link, earth bar and din rail , cable ties for cable management, 240 V, 12 way complete all as specified.

S&F MCB distribution board, SPN 8 Way, Double door, sheet steel, phosphatised, powder painted with bus-bar 200Amp, neutral link, earth bar and din rail , cable ties for cable management, 240 V, 8 way complete all as specified.

S&F MCB distribution board, SPN 4 Way, Double door, sheet steel, phosphatised, powder painted with bus-bar 200Amp, neutral link, earth bar and din rail , cable ties for cable management, 240 V, 4 way complete all as specified.

S&F MCB distribution board, SPN 2 Way, Double door, sheet steel, phosphatised, powder painted with bus-bar 200Amp, neutral link, earth bar and din rail , cable ties for cable management, 240 V, 2 way complete all as specified.

Supply & fix MCB SPN 63 Amps,' C' series , bracking cap10KA, 240V complete all as specified and directed.

Supply & fix in replacement of MCB SPN 40 Amps,' C' series , bracking cap 10KA, 240V complete all as specified and directed.

Supply & fixing in replacement of MCB SPN 6 - 32 Amps, ' C' series ,bracking cap 10KA, 240V complete all as specified and directed.

Supply & fixing in replacement of MCB SP 6 - 32 Amps, ' C' series ,bracking cap 10KA, 240V complete all as specified and directed.

Supply & fix SP enclosure with a two pin and earth plug and socket complete with SP MCB of rating 20 Amps, 240 Volts complete with all connection as directed. Make :- Havells or equivalent of Legrand /L&T/C&S.

Taking down the ceiling fan of any sweep carefully from its installed position, dismantling complete, cleaning all dust, applying grease for bearings, reassembling the fan and blades, painting of fans with synthetic enamel paint by spraying as per existing colour paint including filling cavities with filler, writing MES No. in paint, hanging/fixing the fan in its original position and testing on completion complete all as directed by Engineer-in-charge. Note: The spare parts (like as bearing, capacitor, rubber wheel bush, fan winding etc) required shall be measured and paid separately under relevant items as supply only.

All as per item No. 121 here-in-before but exhaust fans of any sweep.

Supply only ball / bush bearing as per existing & suitable for ceiling fan / exhaust fan complete all as specified and directed.

Material & labour for removing the defective fan winding of ceiling fan size upto 1200mm / 1400 mm sweep and rewinding with super enamelled copper wire of existing gauge, applying insulation varnish, soldering, pre heating and binding with empire tubes, crimple sheet etc. as required for rewinding complete all as specified and directed by Engineer-in-charge.

Material & labour for removing the defective exhaust fan winding of size upto 450 mm sweep and rewinding with super enamelled copper wire of existing gauge, applying insulation varnish, soldering, pre heating and binding with empire tubes, crimple sheet etc. as required for rewinding complete all as specified and directed by Engineer-in-charge.

Supply only rubber wheel bush with GI bolt, nut, washer and split pin complete all as specified and directed.

Supply only down rod 600/900 mm duly powder coated white with GI bolt, nut, rubber wheel bush and split pin, clamp etc including all accessories for fixing fan complete all as specified and directed.

S&F Plastic Surface mounting box 1 / 2 modular gang box for mounting switches, sockets, fan regulator etc complete all as directed by Engineer-in-charge.

S&F Plastic Surface mounting box 3 / 4 modular gang box for mounting switches, sockets, fan regulator etc complete all as directed by Engineer-in-charge.

S&F Plastic Surface mounting box 6 / 8 modular gang box for mounting switches, sockets, fan regulator etc complete all as directed by Engineer-in-charge.

Supply & replacement of 3 mm thick laminated mica sheet top cover suitable for switch board 3 way to 6 way including removing & re-fixing of existing switch / socket and complete connection all as directed. Note :- Replacement of unserviceable switch / socket / regulator shall be measured & Paid separately under relevent item of Sch -A

Supply & replacement of 3 mm thick laminated mica sheet top cover suitable for switch board 8 way to 12 way including removing & re-fixing of existing switch / socket and complete connection all as directed. Note :- Replacement of unserviceable switch / socket / regulator shall be measured & Paid separately under relevent item of Sch -A

M&L for Modular metal flush box 1/2 Module incl cutting & chases( making good all to the disturbed surfaces as per existing) complete all as specified and directed.

M&L for Modular metal flush box 3 Module incl cutting & chases (making good all to the disturbed surfaces as per existing) complete all as specified and directed.

M&L for Modular metal flush box 4 Module incl cutting & chases (making good all to the disturbed surfaces as per existing) complete all as specified and directed.

M&L for Modular metal flush box 6 Module incl cutting & chases (making good all to the disturbed surfaces as per existing) complete all as specified and directed.

M&L for Modular metal flush box 8 Module incl cutting & chases (making good all to the disturbed surfaces as per existing) complete all as specified and directed.

M&L for Modular metal flush box 12 Module incl cutting & chases (making good all to the disturbed surfaces as per existing) complete all as specified and directed.

M&L for modular white cover plate with frame, 1 / 2module complete all as specified and directed.

M&L for modular white cover plate with frame, 3 module complete all as specified and directed.

M&L for modular white cover plate with frame, 4 module complete all as specified and directed.

M&L for modular white cover plate with frame, 6 module complete all as specified and directed.

M&L for modular white cover plate with frame, 8 module complete all as specified and directed.

M&L for modular white cover plate with frame, 12 module complete all as specified and directed.

Supply and fix in repair exhaust fan 300 mm sweep metal body alongwith louvers/front grill complete suitable to work on AC, single phase, 230 Volts, 50 Hz supply and including connecting up with twin core twisted flexible copper conductor cable of suitable size 0.75 Sqmm,complete all as specified.

Supply and fix in repair exhaust fan 250 mm sweep alongwith louvers/front grill, made of sturdy engineering plastic complete, suitable to work on AC, single phase, 230 Volts, 50 Hz supply and including connecting up with twin core twisted flexible copper conductor cable of suitable size 0.75 Sqmm complete all as specified.

Supply and fix in repair exhaust fan 200 mm sweep alongwith louvers/front grill, made of sturdy engineering plastic complete, suitable to work on AC, single phase, 230 Volts, 50 Hz supply and including connecting up with twin core twisted flexible copper conductor cable of suitable size 0.75 Sqmm complete all as specified.

Supply and fix in repair ceiling fan 1200 mm sweep , Energy Saving models, Pearl white / white in colour 350 RPM, 220 volt 50 Hz complete with canopy, down rod. Fan blade, complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable complete all as specified and directed by Enginee-in-Charge. Make - Havells as per Model : ES - 40 or equivalent to Usha, Orient, Khetan

M & L for Point wiring with 1.5 Sqmm (nominal area) single core PVC insulated unsheathed (FRLS) cable, multi-stranded, copper conductor, in universal colour code with & including suitable size of PVC casing & caping and its all accessories complete concealed in wall incl cutting & chases( making good all to the disturbed surfaces as per existing) and modular flush metal boxes including cover plate with frame for mounting modular switches, sockets, regulators,socket etc including earth wire of PVC insulated (FRLS) copper conductor multistranded of 1.5 Sqmm size in green colour complete all as specified in current SSR Part-I & II & directed by the Engineer-in-Charge , as described below:-

One light point/ fan point / bell point controlled by one switch

One 3 pin 5 Amps socket point controlled by one way switch on same board.

One 3 pin 5 Amps socket point controlled by one switch on independent board

All as per item No.149 here-in-before but with 4.0 Sqmm for 3 pin 15 Amps socket point controlled by one switch on independent board and 4.0 Sqmm copper conductor green in colour as earth continuity conductor complete all as specified and directed by Engineer-in-Charge.

Taking down carefully service connection of any type complete all as directed by Engineer-in-Charge.

Excavating in trenches not exceeding 1.5 mtr in depth and not exceeding 1.5 mtr wide for laying of cables and getting out in soft/loose soil all as specified and as directed by Engr-In-Charge.

Removal of excavated surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified.

Returning, filling in including spreading, levelling,watering and well ramming excavated soil in layers not exceeding 25 cm thick each , filling back in trenches after cables have been laid and tested complete all as specified.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 2 core, laid in trenches / duct / fixing on walls / poles or passing through HDPE double wall corrugated pipe (outer dia should not be less then 40 mm) including connecting with suitable lugs, glands, nuts and bolts in existing Panel from pole / Main Panel Box and testing complete all as specified and directed. Note:- Cost of HDPE pipe shall be deemed to be included in unit rate quoted.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core, laid in trenches / duct / fixing on walls / poles or passing through HDPE double wall corrugated pipe (outer dia should not be less then 40 mm) including connecting with suitable lugs, glands, nuts and bolts in existing Panel from pole / Main Panel Box and testing complete all as specified and directed. Note:- Cost of HDPE pipe shall be deemed to be included in unit rate quoted.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core, laid in trenches / duct / fixing on walls / poles or passing through pipe including connecting with suitable lugs, glands, nuts and bolts and testing including connecting with suitable lugs, glands, nuts and bolts in existing Panel from pole / Main Panel Box and testing complete all as specified and directed.

S&F TP&N Vertical Loadline distribution board, 4 Way, Double door, sheet steel, phosphatised, powder painted with bus-bar 200Amp, neutral link, earth bar and din rail ,blanking Plates, cable ties for cable management, 440 V, 4 way complete all as specified including fitting suitable for MCBs with connections complete all as specified and directed. Make : Cat part No DHDLVDRWGOFO04 of havells or equivalent. Note : -MCB & MCB /MCCB DBs shall be of same make and measured and paid seperately under respective items of Sch A. DB shall be fixed in flush pattern by cutting the wall and making good disturbed surface as pe directed & rate shall be included in the items.

Supply & fix in replacement of MCCB 125 Amps,' C' series , bracking cap16 KA, 4 Pole, 415V complete all as specified and directed.

Supply & fix in replacement of MCCB 100 Amps,' C' series , bracking cap16KA, 4 Pole, 415V complete all as specified and directed.

S&F LED post top light fitting 30W IP-65 rated completeall as specified and directed. Make: Surya Cat part No SLE PT 30W-ETPP or equivalent.

M & L for 3 core copper conductor 0.75 sqmm conductor area, PVC insulated, PVC round sheathed multicore, 1100 volt, including with use of PVC pipe / Casing -Caping as per site requirement including taking down old u/s wire complete all as specified and directed by Engr-in-charge.

M & L for 3 core copper conductor 2.5 sqmm conductor area, PVC insulated, PVC round sheathed multicore, 1100 volt, including with use of PVC pipe / Casing -Caping as per site requirement including taking down old u/s wire complete all as specified and directed by Engr-in-charge.

Taking down old unserviceable MCB any type/ size as per existing complete all as specified and directed.

Taking down old unserviceable tube light fitting/Sketch fittings/bulk head/security light etc complete all as specified and directed.

Supply and installation, commissioning of metal top deep freezer single phase 240 volts, 50 Hz, capacity should not be less than 200 Ltrs complete all as specified and directed. Make: LG/BLUE STAR/Voltas or equivalent.

M&L for multi driver for LED down lights 6 watt to 9 watt, 240 V, AC,50 Hz complete including taking down existing driver all as specified and directed.

M&L for multi driver for LED down lights 30 watt to 36 watt suitabel for 2x2 panel, 240 V, AC, 50 Hz complete including taking down existing driver all as specified and directed.

Material and labour for Earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI wire 4.0 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and chaarcoal filling, necessary excavation and earth work complete.

M/S JAGVIR SINGH