CONSTRUCTION OF SAMRAT ASHOK BHAWAN AT NAGAR PANCHAYAT PAWAPURI, DIST-NALANDA

Earth Work in excavation in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Supplying and filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per bui9lding specification and direction of E/l,

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level-1:2:4 (1 cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size)

Boring, Providing and installing cast in situ single under reamed piles of specified diameter and elngth below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) : 300 mm dia piles

Extra over item No. 23.3 for providing additional bulb in under reamed piles, undedr specified dia meter (Only the quantity of extra bulbs are to be paid). 300

Providing and laying in position specified grade of reinforced cement concrete exluding the cost of centring shuttering, finishing and reinforcementg-all work upto plinth level-1:1:2 (1 cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in wall (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts, etc. upt floor five level excluding cost of centring, shuttering, finishin and reinforcement. 1:1:2 (1 cement: 1 coarse sand: 2 graded stone aggregate

Providing average 150 mm thick dry rammed khoa beaten to 112 mm (compacted with water) made of well burnt or jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blinding the top with cement mortar (1: 10) all complete as per building specification and direction

Brick work 100A one bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in : cement mortar 1:6 (1 cement: 6 coarse sand)

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1cement:2:2 coarse sand:4 graded stone aggregate 20mm

Brick work 100A one bricks as per IS 12894(2002) & IS 3495 in superstructure above plinth level upto

At Ground Floor

1st Floor

Half Brick masonry with non modular fly ash bricks of class designation 10, conforming IS: 12894, in superstructure above plinth and upto floor V level.

Ground Floor Quantity

1st Floor Quantity

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type core of block board construction with fr5ame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters 35 mm thick including stainless steel butt hinges with

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections, joints mitered and welded with 15×10×10 cm of 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with

Extra for Providing and fixing steel beading of approved shape and section with screws instread of glaxing clips and met. Sash putty in steel doors, windows, Ventilators and comosite units.

Providing and laying vitrifed floor tiles in different sizes (thickness to be specified by the manufactruer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm

12 mm cement plaster of mix 1:6 (1 cement : 6 coarse sand)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade Two or more coas

Providing and laying Ceramic glazed floor tiles 300×300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such shades except white, lvory, Grey, Fume Red, Brown, laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete.

Kota stone slabs 20 mm thick in risers of steps skirting. Dado & pillars laid on 12 mm (average (thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. Details of cost for 10 sqm

Providing and fixing M.S grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Providing and fixing hand rail by welding etc. to steel ladder railings & staircases railing including applying a priming coat of approved steel primer MS tube (medium) 40 MM nominal bore

Providing and fixing M.S.fan clamp type I or II of 16 mm dia.M.S. bar bent to shape with hooked ends in R.C.C. clabs during laying including painting the exposed portion of loop, all as per standard design complete

Providing and laying integral cement based water proofing treatment including prepattion of surface as required for treatment of roots balconies terrces etc consisting of

Providing and fixing on wall face 110 mm diameter unplastised- PVC (working pressure 4 kgf per sqm) rain water pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion.

Providing and fixing 110 mm diameter unplasticised- PVC pipe clip of approved design to unplasticised PVC rainw ater pipe by means of 50x50x50mm hard wood plugs, scrwed with M.S. screws of required length including cutting brick work and fixing on cement mortar (1:4) 1 cement: 4 corsa sand and making good the wall etc complete

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

6 mm cement plaster to celing of mix :1:4 (1 cement : 4 coarse sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade over Applying one coat of cement primer of approved brand and manufacture on wall surface:

Painting on Steel surface grill with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution

Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with synthetic enamel paint of approved brand and manufacture and required colour over a priming coat of ready mixed zinc chromatic yellow primer on new work.100 mm diameter pipes

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. 6 mm round bar.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.

Thermo-Mechanically Treated bars TMTC-500-8mm dia.

Thermo-Mechanically Treated bars TMTC-500-10mm dia.

Thermo-Mechanically Treated bars TMTC-500-12mm dia.

Thermo-Mechanically Treated bars TMTC-500-16mm dia.

Thermo-Mechanically Treated bars TMTC-500-20mm dia.

Thermo-Mechanically Treated bars TMTC-500-25mm dia.

Centring and shuttering including strutting, propping etc. and removal of form for.

Brick work with bricks of class designation 100A in foundations and plinth in Cement mortar 1:4 (1cement : 4 coarse sand)

12 mm cement plaster 1:4 (1 cement : 4 coarse sand) finished with a floating coat of near cement Details of cost for 10 sqm

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement

Providing and laying in position cement concrete of specified grade exluding the cost of centring and shuttering-all work upto plinth level-1:1.5:3 (1 cement: 1.5

Centring and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns etc. for mass concrete

Making 25 cm (10") dia bore up to 4 mtr depth below ground with hand auger of approved quality in ordinary soil (vide classification of soil item A) true to plumb and without eccentri city in any stage of operation and disposal of the excavated earth up to 50 mtr, Lead in eluding all lifts, all complete as per approved disign and direction of E/I

63 CM (25) UNDER-REAM Making 63 cm (25) dia under ream at required with hand auger of approved quality in in ordinary soil (vide classification of soil ifem-A) true to plumb and without eccentri city in my stage of opration and disposal of the excavated earth up to 50 mts lead in eluding all lifts, all complete as per approved design and direction of (E/I)

12 mm cement plaster 1:4 (1 cement: 4 coarse sand) -do-all comp. job as per direction of E/I

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all

Painting with ready mixed paint of approved brand and manufacture in all shades to give an even shade on New steel work (two or more coats) over Applying priming coat With ready mixed zinc chromate yellow primer of approved brand and manufacture on steel galvanized iron/steel works

Boring, Drilling bore well of required dia for casing/strainer Pipe by suitable method prescribed in IS:2800 (Part-i) including collecting samples from different strata, preparing and submitting Strata Chart/Bore log including hire & running charges of all equipments, tools, plants & machineries required for the job all complete as per direction of Engineer-in-Charge upto 90 metre depth below ground level with Rocky Strata including 300 mm dia Boulders.

Supplying. Assembling, Lowering and fixing in Vertical position in bore well, unplasticized PVC medium well casing (CM) Pipe of required dia conforming to IS:12818 including required hire and labour charges, fittings & accessories etc. all complete for all depths as per direction of Engineer-in-Charge.-100 mm Nominal Size dia

Supplying, Assembling, Lowering and fixing in Vertical position in bore well, unplasticized PVC medium well screen (RMS) Pipes with ribs, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete for all depths as per direction of Engineer-in-Charge. -100mm Nominal Size dia

Gravel packing in Tube Well construction in accordance with IS:4097 including providing gravel finel medium/coarse in required grading & sizes as per actual requirement all complete as per direction of Engineer-in-Charge.

Development of Tube Well in accordance with IS:2800 (part-i) and IS:11189 to establish maximum rate of usable water yield without sand content (beyond permissible limit) with required capacity Air Compressor, running the Compressor for required time till well is fully developed measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory i/c disinfection of Tube well all complete including hire & labour charges of Air Compressor, Tools & Accessories etc. All as per requirement and direction of Engineer-in-Charges.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/casing pipe, removable as per requirement all complete for borewall of 100 mm dia.

Providing and fixing M.S. Clamp or required dia to the top of Casing/housing pipe of Tube well as per IS:2800 (Part-i) including necessary bolts & nuts of required size complete with 100 mm clamp.

Providing and fixing Ball Plug/Bottom Blaug of required dia to the bottom of pipe assembly of Tube well as per IS:2800 (part-i) with 100 mm dia.

Strainer Bress 40 mm dia 1.5 m long

Suppling and fixing 1 H.P. Submersible Pump of ISI Mark with Starter Pannel Cable with all accessories as per Market Rate

Providing and placing on terrace (at all floor levels) Polyethylene Water storage Tank, ISI:12701 marked with cover and suitable locking arrangment and making necessary holes for inlet, outlet and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for Tank.

Providing and fixing G.I. Pipes complete with G.I. Fittings and Clamps, i/c cutting and making good the wall etc.

Providing and fixing G.I. Pipes complete with G.I. Fittings and Clamps, i/c cutting and making good the wall etc. concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall:

Providing and fixing Gun Metal Gate Valve With C.I. Wheel of approved quality screwed end):

Providing and fixing G.I. Union In G.I. Pipes including cutting and threading the pipe and making long screws etc. complete (New Work).

Providing and fixing C.P. Brass Bib Cock of approved Quality conforming to Is:8931

Providing and fixing water closet squatting pan (Indian Type W.C. Pan) with 100mm sand Cast Iron P or S trap, 10 Litre low fixtures complete including cutting and making good the walls and level white P.V.C flushing cistern including flush pipe with manually controllec device (handle lever) confornming to IS:7231 with all fittings and floors wherever required White Vitreous China Orissa Pattern W.C. Pan of size 580x440 mm with integral type foot rests.

Painting and fixing White Vitreous China Flat back or wall corner type lipped front Urinal Basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. Clamps complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required One Urinal basin with 5 Litre White P.V.C. automatic Flushing Clstern.

Painting and fixing Wash Basin with C.I. Brackets, 15 mm C.P. Brass Pillar taps, 32 mm C.P. Brass Waste of Standard pattern including painting of fittings and brackets, cutting and making good the walls whereas require white Vitreous China Flat Back Wash Basin size 550x400 mm with Single 15 mm C.P. Brass Pillar Tap.

Providing and fixing 600x450 mm bevelded edge Miror of Superior Glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. Brass screws and washers complete.

Providing and fixing on Wall face unplastidsed - PVC (Working pressure 4 kgf per sqm) rain water pipes confirming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion.

Providing and fixing on wall face unplastidsed PVC molded fittings?accessories for unplasticsed PVC rainw ater pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion.

Providing and fixing unplasticised PVC Pipe Clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50 mm hard wood plugs, screwed with M.S. Screws of required length including cutting brick work and fixing on Cement Mortr (1:4) (1 cement: 4 Coarse Sand and making good the wall etc. complete 110mm.)

Providing and laying non-pressure NP2 class (Light Duty) R.C.C. Pipes with Collars jointed with stiff mixture of Cement Mortar in the proportion of 1:2 (1 Cement : 2 Fine Sand including Testing of joints etc. complete 150 mm dia R.C.C. Pipe

Constructing Brick Masonry Chamber for underground C.I. Inspection Chamber and bends with bricks in Cement Mortar 1:4 (Cement : 4 Coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 39 kg. (Weight of cover 23 kg. and weight of frame 15 kg). R.C.C. Top Slab with 1:2:4 Mix (1 Cement : 2 Coarse Sand : 4 Graded Stone aggregate 20 m nominal size) foundation concrete 1:5:10 (1 Cement : 5 Fine Sand : 10 Graded Stone Aggregate 40 mm Nominal Size), inside plastering 12 mm thick with Cement Mortar 1:3 (1 Cement : 3 Coarse Sand), finished smooth with a floating coat of neat Cement on walls and bed concrete etc. complete as per standard design inside dimensions 455x610 mm and 45 cm deep for single pipe line with common burnt clay F.P.S. (non Modular) Bricks of Class designation 7.5.

Providing and fixing Stainless Steel A ISI 304 (18/8) Kitchen Sink as per IS:13983 with C.I. Brackets and Stainless Steel Plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink without Drain board with 470x420 mm bowl depth 178 mm

Providing and fixing G.I. Pipes complete with G.I. Fittings and Clamps, i/c cutting and makin good the wall etc.

Providing and fixing G.I. Pipes complete with G.I. Fittings and Clamps, i/c cutting and makin good the wall etc. concealed pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall:

Providing and fixing Gun Metal Gate Valve With C.I. Wheel of approved quality (screwed end)

Providing and fixing required Stainless Steel Fitting of Press fit design of Grade AISI 304 conforming to JWWA G116 standard with V-Profile or M-Profile and with O-ring sealing Gasket of EPDM Material of required dia as per direction of Engineer-in-Charge. Femable Thread Connector/Adapter.

Providing and fixing C.P. Brass Bib Cock of approved Quality conforming to Is:8931

Providing and fixing PTMP Soap Dish Holder having length of 138 mm breadth 102 mm, hight of 75 mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing Stainless Steel A ISI 304 (18/8) Kitchen Sink as per IS:13983 with C.I. Brackets and Stainless Steel Plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required Kitchen sink without Drain Board with 470x420 mm bowl depth 178 mm

Providing and fixing PTMP Swivelling Shower, 15 mm Nominal Bore, Weighting not les than 40 gms

Providing and fixing 600x450 mm bevelded edge Miror of Superior Glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. Brass screws and washers complete.

Providing and fixing on Wall face unplastidsd PVC (Working Pressure 4 kgf per sqm) rain water pipes confirming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10 mm gap for thermal expansion.

Providing and fixing on wall face unplastidsed PVC molded fittings?accessories for unplasticsed PVC rainw ater pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion.

Providing and fixing unplasticised PVC Pipe Clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50 mm hard wood plugs, screwed with M.S. Screws of required length including cutting brick work and fixing on Cement Mortr (1:4) (1 cement : 4 Coarse Sand and making good the wall etc. Complete-110 mm.)

Providing and laying non-pressure NP2 class (Light Duty) R.C.C. Pipes with Collars jointed with stiff mixture of Cement Mortar in the proportion of 1:2 (1 Cement : 2 Fine Sand) including Testing of joints etc. complete

Providing and fixing Vitreous China Dual purpose closet suitable for use as squatting Pan or European Type Water Closet (Anglo Indian W.C. Pan) with Seal & lid fixed with C.P. Brass hinges and rubber buffoers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required White vitreous China dual purpose Wc Pan with white Solid plastic Seat and lid with White Vitreous China Flushing Cistern and C.P Flush Bend.

Painting and fixing PTMP Towel Rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour 600 mm towel rail with total length of 645 mm width 78 mm and effective height of 88 mm weighing not less than 190 gms.

Wiring for light point/fan point/exhaust fan point/ call bell point with 1.5 sq. mm FR PVC Insulated copper conductor single core cable in surface/recessed medium class PVC conduct with modular switch. Moldular class PVC conduct with Modular Switch, Modular Plate, sultable size G.I. Box etc. as required.

Supplying and fixing suitable size GI Box with Modular Plate and cover in Front on surface or in recess including providing and fixing 3 Pin 5/6 Amps modular socket Outlets and 5/6 Amps Modular Switch, connection etc. as required.

Supplying and fixing suitable size GI Box with Modular Plate and cover in Front on surface or in recess including providing and fixing 6 Pin 5/6 Amps & 15/16 Amps modular socket Outlets and 15/16 Amps Modular Switch, connection etc. as required.

Wiring for light/power Plug with 2 x4 sq. mm FRLS PVC insulated copper conductor Single Core Cable in Surface/recessed medium class PVC conduct along with 1 Nos. 4 sq. mm FR PVC insulated Copper conductor Single Core Cable for Loop Earthing as required.

Supplying and fixing suitable size GI Box with Modular Plate and cover in Front on surface or in recess including providing and fixing 3 Pin 5/6 Amps modular socket Outlets and 5/6 Amps Modular Switch, connection etc. as required. And 6 Pin 5/6 Amps & 15/16 Amps modular socket Outlets and 15/16 Amps Modular Switch, connection etc. as required and supplying and fixing 6/32 Amps single Pole rating, 240/415 Volts, "C" Curve, miniature Circuit Beaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Wiring for Circuit/sub main wiring along with Earth Wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required.

Supplying and fixing following way single pole & neutral, Sheet, MCB Distribution Board, 240 Volts on surface/recess, complete with tinned copper Bus bar, neutral bus-bar, Earth Bar, Din Bar, interconnections, powder painted including earthing etc. as required (but without MCB/Rccb ? Isolator)

Supplying and fixing following way single pole & neutral, Sheet, MCB Distribution Board, 240 Volts on surface/recess, complete with tinned copper Bus bar, neutral bus-bar, Earth Bar, Din Bar, interconnections, powder painted including earthing etc. as required 9 but without MCB/RCCB/Isolator)

Supplying and fixing following rating, 240/415 Volts, "C" Curve, miniature Circuit Breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 2 Pin, 5/6 Amp Ceiling Rose on the existing junction box/wooden block including connection etc. as required.

Supplying and fixing betten/agnle holder including connection etc. as required.

Supplying and fixing of following typs lamp in the existing Electrical fitting/fitting/fixtures etc. as required-20 Watt CFL Lamp

Supplying and fixing Ding-Dong Call Bell suitable for Single Phase, 230 Volts Complete as required.

Supplying and fixing recess mounted 36 Watt LED Flat Panel ('2 x 2') with minimum efficacy 100 IM/W which provides soft light and glare free symmetrical illumination sultable for arm strong/ Grid Ceiling and Integrated electronic driver etc. directly on false Ceiling including connections with 1.5 sq. mm FIRLS PVC insulated copper Conductor Cable etc. as required

Supplying and fixing Wall mounted light bracket/fixture made with polycarbonate suitable for single 9/10 Watt LED directly on Wall including connections etc. as required. (but without Lamp)

Supplying anf fixing 90 Watt LED Type Street Light with Minimum efficacy 100 Im/w in die cast aluminium housing, toughened glass, IP 66 protection and complete with Electronic driver etc on pole/building including connection earthing the body etc. as required.

Supplying and fixing of 32 mm diax 1.00 M long G.I. Pipe (Medium Class) Bracket for mounting of fluorescent/HPMV/HPSV/LED Street Light fitting on Pole including bending the Pipe to the required shape, 2 Nos. 40 mm x 3 mm Flat iron Clamps with nuts, bolts and washer, painting the Flat iron with Primer and Finish paint etc. as required.

Supplying and fixing 20 Amps, 240 Volts, SPN Industrial type, Socket outlet with 2 Pole and Earth, Metal enclosed Plug top along with 20 Amps "C" Curve, SP MCB, in sheet steel enclosure, on surace or in recess, with chained metal cover for the socket outlet ad complete with connections, testing and commissioning etc. as required.

supplying and fixing Modular blanking Plate for Modular Plate as required.

Supplying and fixing stepped type Electronic Fan regulator on the existing modular plate/switch box including connections but excluding modular plate etc. as required.

Supply and installation of reqular/standard model A.C. Ceiling Fan of 1200 mm Sweep including wiring the down rods of standard length (upto 30cm) with 1.5 sq. mm FR PVC insulated Copper Conductor etc. as required.

Supply and installation of 400 mm, 230 V A.C. Wall/Cabin Fan Including fixin the Bracket making connection, testing, commissioning etc. as required.

Supply and fixing of 250 mm sweep (130/140 RPM) PVC/ABS square body Exhaust Fan with automatic openable louvre shutter in existing opening including making connection, testing etc. as required.

Supplying and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal sreaders ine xisting cubcle panel board including drilling holes in cubicle panel, making connections etc. as required.

Supplying and fixing following rating 240/415 Volts "C" Curve, miniature Circuit Breaker suitable for inductive loads of following Poles in the existing MCB DB complete with connections, testing and commissonin etc. as required.

Supplying and fixing following rating 240/415 Volts "C" Curve, miniature Circuit Breaker suitable for inductive loads of following Poles in the existing MCB DB complete with connections, testing and commissonin etc. as required.

Providing and fixing following capacity four Pole on Load/Panel mounted Change over Switches inside the existing Cubical Panel Board including Driling holes in cubicle panel, making connections etc. as required.

Providing and fixing Wall/Floor mounted cubical panel board fabricated with 16 Guage Iron Sheet, suitable for panel mounted Switch disconnector including Bus-Bar Chamber, insulator and painting etc. as required (but without Busbar Copper Strip)

Supplying and fixing of Copper Strip of 50 mm x 5mm sizes (2.30 kg./ mtr)

Supply and fixing panel mounted digital multimeter 9 Voltmeter & Ammeter including ct coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board, making connection etc. as required.

Providing 3.5 Core, 70 sq. mm XLPE/PVC insulated PVC sheathed (Heavy Duty) armoured Electric Cable with Aluminium Conductor

Laying of one number PVC insulated and PVC Sheathed/XLPE power Cable of 1.1 KV Grade of following size direct in ground including excavtion, sand cushioning, protective covering and refilling the trench etc. as required.

Brick work with fly ash bricks as per IS 12894 (2002) & Is 3495 in foundations and plinth in : cement mortar 1.:4 ( 1 cement: 4 coarse sand)

Providing, laying and fixing of 80 mm dia dia G.I. Pipe (Medium class) in ground complete with G.I. fittings including trenching (75 cm Deep) and refiting etc. as required.

Earthing with G.I. Earth Plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonary enclosure with cover pate having locking arrangement and watering pipe 2.7 metre long etc. with charcoal/coke and salt as required.

Providing and fixing 4.00 mm dia Copper Wire on surface or in recess for loop Earthing etc. as required.

Coarse Sand

Stone Chips

Bricks

Local Sand

cement

Bricks