Construction and Renovation work of New Building at Government Polytechnic, Kharsawan for Developing it as a State of the Art Institution

Amount

EARTH WORK IN EXCAVATION IN FOUNDATION Trenches in ordinary soil (vide classification of soil item -A) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I.

EARTH WORK IN EXCAVATION IN FOUNDATION Trenches in ordinary soil (vide classification of soil item -A) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed.

Ordinary Rock

FILLING IN FOUNDATION TRENCHES AND PLINTH in layers not exceeding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)

IN FOUNDATION TRENCHES + FILLING IN BUILDING TO RAISE G.L.+ IN PLINTH

Providing coarse clean local SAND IN FILLING in foundation trenches or in plinth including ramming and watering in layer not exceeding 150 mm thick with all leads and 1.5 M lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer Incharge (Mode of measurement compacted volume)

Providing designation 75-A, BRICK FLAT SOLING joints filled with local sand including cost of watering,taxes and royalty all complete as per building specification and direction of Engineer Incharge

Providing designation 75-B, one BRICK FLAT SOLING joints filled with local sand including cost of watering,taxes and royalty all complete as per building specification and direction of Engineer Incharge

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:3:6 (1 cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.

With material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

Providing and filling BRICK BATS in toilet sunken slab after waterproofing treatment of slab and beam sides including all taxes all complete.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work up to plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum

IN FOUNDATION ,

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum

COLUMN

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum

LINTEL BAND

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum

LINTEL

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum

STAIRCASE-

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.

Note - Extra cement upto 10% of the minimum specified cement content in design mix shall be paid separately. In case the cement content in design mix is more than 1.10 of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

All work above plinth level :

Concrete of M25 grade with minimum cement content of 330 kg /cum

CHAJJA

Providing, hosting and fixing above plinth level up to floor level precast Reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand ), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , exculuding the cost of reinforcement, with 1:1.5:3 (1cement : 1.5 coarse sand (zone-iii) : 3 graded stone aggregate 20mm nominal size)

Centering and shuttering including struting, propping etc. and removal of form for -

Foundation, footings, bases of columns etc.

Columns

ROOF SLAB

Beams, plinth beams,-

STAIRS -

CHAJJA

Edges of slabs and breaks in floors and walls

Under 20 cm wide

Providing tor steel reinforcement TMT FE 500 of following dia. rods as per approved design and drawing including carriage of bars to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction and direction of E/I. (ONLY VALID FOR SAIL & TATA STEEL, JSPL, ELECTRO STEEL LTD. AND VIZAG STEEL)

TOR 8 MMDIA.

TOR 10 MMDIA.

TOR 12 -32 MM DIA.

TOR 28 -32 MM DIA.

Providing designation 75A brick work in C.M. (1:6) in foundation & plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm. thick mortar joints,cost of screening materials raking out joints to 15mm depth , curing, taxes & royalty all complete as per building specification & direction of E/I.

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 20mm nominal size)

Extra for providing and mixing waterproofing material in cement conncrete work in doses by weight of cement as per manufacturer's specification.

Providing designation 75 A BRICK WORK in CM. (1:6) in SUPERSTRUCTURE with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening,racking out joints to 15 mm depth,curing, taxes and royalty all complete as per building specification and direction of Engineer Incharge

Providing designation 75B brick work in C.M. (1:6) in foundation & plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm. thick mortar joints,cost of screening materials raking out joints to 15mm depth , curing, taxes & royalty all complete as per building specification & direction of E/I.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Providing 125 mm thick REINFORCED DESIGNATION 75 A BRICK WORK in C.M. (1:4) in SUPERSTRUCTURE with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, cost of materials, racking out joints to 15 mm depth, carriage, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of Engineer Incharge .

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Providing 12 mm thick CEMENT PLASTER (1:4) with clean coarse sand of F.M.1.5 and waterproofing compound (as per specified and approved) including cost of screening, curing making grooves with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I. (Cost of waterproofing compound will be paid separately)

Providing 12 mm Thk. cement plaster(1:6) on inside walls with clean course sand of FM-1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I

Providing 6mm cement plaster(1:4) in ceiling with clean course sand of FM-1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I

Providing 12 mm thick water proof CEMENT PLASTER (1:6) on outside wall with clean coarse sand of F.M.1.5 and waterproofing compound (as per specified and approved) including cost of screening, curing making grooves with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I. (Cost of waterproofing compound will be paid separately)

Providing tuck pointing [1:3] in cement on brick work clean coarse sand of F.M 1.5 FM-1.5 including screening, curing with all leads & lifts of water, scaffolding taxes & royalty all complete as per building specification and direction of E/I

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.

With cement mortar 1:4 (1cement: 4 coarse sand)

Providing & fixing FAN HOOK of 16 mm dia M.S. bar, 1 M long bent to required size and shape, placed in position and fluid in the R.C.C. slab-beam at the time of casting all complete as per building specification and direction of E/I.

Supplying, fitting & fixing 250 x 20 x 6 mm L-type M.S. clamp properly fishtailed including making holes and setting the same in 375 x 125 x 75 mm cement concrete block (1:2:4) with cost of all layout and materials and taxes as per building specification and direction of E/I.

Making 6x6 / 20x6 mm grooves in plaster surface over walls trully horizontal or vertical as specified at regular intervals at all heights including cleaning finishing , scaffolding and curing with all leads and lifts of water all complete as per buildinng specification and direction of E/I. (6

Extra for brick work for each consecutive floor above first floor including watering and scaffolding, all complete as per direction of E/I.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Extra for PLASTER work over exterior surface for each consecutive floor above first floor including cost of scaffolding etc. all complete as per direction of E/I.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

FLOORING WORKS

Providing and laying DOUBLE CHARGE VITRIFIED FLOOR TILES in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08% and confirming to IS : 15622/ ISO 13006, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.30 kg per sqm including grouting the joints with white cement and matching pigments etc. complete.

SIZE OF TILE- 600MMX600MM

Providing and laying matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. OVER OUTER WALL

Providing & laying 15 mm to 23 mm thick KOTAH STONE SLAB FLOORING and skirting of approved size, texture and colour over 19 mm thick base of line mortar (1:1:1) Lime putty: Surkhi: Coarse sand) laid over and jointed with grey cement slurry mixed with pigment ot match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying 25 mm thick kotah stone tiles in risers of steps, skirting and pillars of approved size texture and colour laid over 12 mm thick cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing to granolithic finish with approved quality of carborandum stone including cost of curing taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying 6 mm precast white GLAZED CERAMIC TILES in walls over 12mm cement mortar (1:3) and jointed with white cement slurry flush pointed with white cement including rubbing, polishing and cost of curing taxes, and royalty all complete as per building specification and direction of E/I

with commercial grade colour tiles.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Marble stone flooring with 18 mm th marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm thick base of cement mortar 1:4 (1cement :4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with:

Udaipur Green Marble

Extra for pre finished nosing to treads of steps of marble stone

Extra for marble stone flooring in treads of steps and risers using single length upto 2.00 m

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels

Granite stone slab colour black, Cherry/Ruby red

Area of slab over 0.5 sqm -

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Providing 50mm thick Cement Concrete Flooring ( 1:2:4 ) with 20mm to 6mm size graded stone chips finished with floating coat of neat cement in panels, including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm cement plaster(1:3) with clean course sand of F.M 1.5 with floating coat of neat cement in skirting including rounding of junctions with floor, curing taxes and royalty all complete as per building specification and direction of E/I.

38 mm thick wood block flooring of first class teak wood laid over 25 mm thick leveling layer of cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 10 mm nominal size) to be paid separately, coated with a thin layer of hot bitumen penetration 80/25 (blown type) @ 2.45 kg per sqm, including fixing blocks in position after dipping in hot bitumen (blown type) up to half depth, planed, levelled smooth and finished complete.

Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50 cm deep and1.8 cm thick fixed in Urinal Partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1cement :2 coarse sand : 4 stone chips)as per direction of E/I and finished smooth.

Providing and laying pressed clay tiles (as per approved pattern 20mm nominal thickness and of approved size) on roofs jointed with cement mortar 1:4 (1 cement:4 coarse sand) mixed with 2% integral water proofing compound laid over a bed of 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete.

Providing and laying vitrified Parking/Industrial tile in different sizes (thickness to be speified by the manufacture) with water absorption less than 0.08% and confirming to IS:4457:2007, of approved make in all colours and shades laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg./ sqm.including grouting the joints with white cement and matching pigments etc. complete size of tile 300x300x10mm sizes all complete as per building specification and direction of E/I.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.

80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20mm thick bed of cement mortar 1:4( 1 cement : 4 coarse sand )

Dark shed pigment using ordinary cement

Providing and laying vitrified Parking/Industrial tile in different sizes (thickness to be speified by the manufacture) with water absorption less than 0.08% and confirming to IS:4457:2007, of approved make in all colours and shades laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg./ sqm.including grouting the joints with white cement and matching pigments etc. complete size of tile 300x300x10mm sizes all complete as per building specification and direction of E/I.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.

80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Extra for FLOORING work for each consecutive floor above first floor, all complete as per direction of E/I.

DOORS & WINDOWS WORKS

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Frame size 50 x 100 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)

25 mm thick

suppling , fitting and fixing good quality well dressed and well seasoned sal wood work in chaukhat in doors window ,sky light, fanlight and celevitial window opening including wedge over clmps all including application of two coats of wood preservative of approved quality on the surface , building walls and lintel all complete as per building specification and direction of El.

Supplying, fitting & fixing 35 mm th. Solid core type non-decorative single leaf FLUSH DOOR SHUTTERS in doors with block board core blended with high quality phenol formal dehydes synthetic resinboth side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts , handle,cleats aldrop, door stopper & sand blocks & taxes all complete as per detail drawing building specification & direction of the E/I.

Supplying, fitting & fixing 35 mm th. Solid core type non-decorative double leaf FLUSH DOOR SHUTTERS in doors with block board core blended with high quality phenol formal dehydes synthetic resinboth side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts , handle,cleats aldrop, door stopper & sand blocks & taxes all complete as per detail drawing building specification & direction of the E/I.

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-incharge (Frame work shall be paid for separately).

12mm thick commercial ply conforming to IS : 1328 BWR type

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality.

1.0 mm thick

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured):

Rectangular or square

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i. e. at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/ Neoprene gasket etc complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4.0 mm thickness (weight not less than 10kg/ sqm)

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete.

With 12 mm mild steel U beading

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber/ Neoprene gasket etc complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg/ sqm)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Pre-laminated particle board with decorative lamination on both sides

Providing and fixing Double action hydraulic floor spring of approved brand and manufacture I.S.:6315 marked, Hardwyn Make (Model 3000) or equivalent for doors including cost of cutting floors as required, embedding in floors & cover plates with brass pivot and single piece M.S. sheet outer box with side plate etc.complete as per the direction of E/I. WITH STAINLESS STEEL COVER PLATE MINIMUM 1.25MM THICKNESS:-

DOOR WINDOW

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in-charge. (Approved brand - Godrej/ Dorset)

Providing and fixing aluminium round shape handle of outer dia.100 mm with SS screws etc. coplete as per direction of E/I.

Powder coated minimum thickness 50 micron aluminium.

Providing and fixing aluminium hanging floor door stoppers ISI marked anodized (anodic coating not less than grade Ac 10 as per I.S. 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Twin rubber stopper

Providing and fixing aluminium TOWER BOLTS ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required color or shade with necessary screws etc. complete.

Extra for providing lipping with 2nd class teak wood battens 25mm minimum depth on all edges of shutters (over all area of door shutter to be measured).

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:

a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.

c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass.

d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.

e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineerin- Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves ) on the external face shall be measured in sqm. up to two decimal places.

Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NBL Certified laboratories

1. Performance Laboratory Test for Air Leakage Test (-50pa to – 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr”

2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml.”

3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml”

4. Structural Performance Deflection and deformation by static air pressure test (1.5 times desing wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm”

5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test” Tests to be conducted on site

6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000ml”

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge.

Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic float glass (loee glass) of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc. ,all complete for the required performances as specified, as per the Architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in- Charge. For payment, only the actual area of glass on face # 1 of the glass panels (but excluding the area of grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.(Payment for fixing of Spandrel Glass Panels in the curtain glazing is included in cost of relevent Item*).

(i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. . The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Supplying, fitting & fixing local made COLLAPSIBLE GATE of approved size and make properly fabricated with vertical double channel 20 x 10 x 2 mm at 100 mm center and braced with M.S. flat diagonals 20 x 3 mm with top and bottom rail of T. iron 40 x 40 x 6 mm with 38 dia steel pulleys complete with bolt, buts locking arrangement, steppers, handles including applying a primer coat of read lead paint carriage, hoisting and taxes etc. all complete as per building specification and direction of Engineer Incharge.

Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer-in -charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of ClassA category with properties of being termite/borer roof,water/moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 251.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In-Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately.

Supplying, fitting & fixing M.S. GRILL made of 20 x 6 mm flat as per approved design and drawing properly fabricated with joints continuous fitted, welded and finished smooth, hoisting as per building specification and direction of E/I.

Providing and fixing sliding arrangement in racks/ cupboards/cabinets/ Window shutter by with stainless steel rollers to run inside C or E aluminium channel section (The payment of C or E channel shall be made separately)

Extra for providing ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws. (Shutter area to be measured).

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brandincluding 2mm thick PVC edge banding tape with hot glue byedge bending machine etc. with auto closing spring loadedhinges {hydraulic type) etc. complete as per direction of Engineerin-charge.(Payment of providing and fixing auto closing hinges shall be paid separately)

Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand boxes, shelves, racks, almirah, cupboard and drawer etc. including necessary nails, screws etc. complete as per direction of Engineer-in-charge.

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc.complete:

Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge.

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete:

25 mm dia. (Heavey type)

Providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineer-in-charge.

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete.

Providing and fixing magnetic catcher of approved quality in cupboard/ ward robe shutters, including fixing with necessary screws etc. complete .

Triple strip vertical type

Providing and fixing ready made 304 grade stainless steel Modular kitchen basket and accessories such as right angle basket (Plain Cup & Saucer, plant, Partition, Bottle rack, Thali, Cutlery) kitchen utensil basket, Dinner set basket, kitchen grain basket, Multipurpose basket as per site requirement including finishing (wherever required) and fittings. The same shall be fixed with necessary stainless steel nuts & bolts, Stainless Steel screws & telescopic channel etc. as per direction of Engineer incharge. (For payment purpose only weight of Stainless steel basket shall be considered excluding weight of all fixing accessories such as nuts, bolts, fasteners telescopic basket channels etc. Payment of providing and fixing telescopic channel shall be paid separately)

WATER PROOFING TREATMENT

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roof terraces etc. consisting of following operations.

Applying and grouting a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with proprietary water proofing compound conforming to IS : 2645 over the RCC slab including cleaning the surface before treatment.

Laying cement concrete using broken bricks/brick bats 25 mm to 100 mm size with 50% of cement mortar of mix 1:5 ( 1 cement : 5 coarse sand ) admixed with proprietary water proofing compund conforming to IS :2645 over 20 mm thick layer of cement mortar 1:5 (1 cement : 5 coarse sand ) admixed with proprietary water proofing compund conforming to IS :2645 to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs

After two days of proper curing applying a second coat of cement slurry admixed with proprietary water proofing compound conforming to IS: 2645.

Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 ( 1 cement : 4 coarse sand ) admixed with proprietary water proofing compund conforming to IS : 2645 and finally finishing the surface with trowel with neat cement slurry and making of 300X300 mm square.

The whole terrace so finished shall be flooded with water for minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the E/I.

With average thickness of 120 mm and minimum thickness at khurra as 65 mm. (WORKS TO BE DONE BY REGISTERED APPLICATOR OF PIDILITE/ SIKA/ ROFF WITH 10 YRS. GUARANTEE.)

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/ 5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane : (Approved Brand - MYK/Asian/ STP)

Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100% polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.

Covering of treated surface with PCC :- Providing 50mm thick Cement concrete M20 (1:1.5:3) maintaining slope in alternate 2mtX2mt panels with approved quality of stone chips of 20mm to 6mm size graded and cleaned sand of F.M. 2.5 to 3 including screening, shuttering, and mixing cement concrete in mixer with admixture of integral waterproofing and placing in position striking curing, taxes and royality all complete as per building specification and direction of E/i. Panels that has been left should be casted next day. There should be 6mm gap betwwen panels. Brand - Sika Plastocrete Plus, MYK proof WP, Fosroc-Conplast X4211 C,. Dr. Fixit Pidiproof LW+.(WORKS TO BE DONE BY REGISTERED APPLICATOR OF ABOVE MATERIALS WITH 10 YRS. WRITTEN GUARANTEE.)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying

a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

(WORKS TO BE DONE BY REGISTERED APPLICATOR OF PIDILITE/ SIKA/ ROFF WITH 10 YRS. GUARANTEE.)

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI?212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

For vertical surface two coats @ 0.70 kg per sqm

For horizontal surface one coat @1.10 kg per sqm

Providing 12mm cement plaster(1:3) with clean coarse sand of F.M 1.5 including screening, curing with all leads and lifts of water scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 1.5 mm th. cement punning including curing, carriage of water with all leads and lifts as per building specification and direction of E/I.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I

Providing two coat of snowcem of approved shade and make over a coat of cement of primer on new surface including preparing the plastered surface smooth with sand paper, soaping, curing and taxes all complete as per building specification and direction of E/I.

Finishing walls with Premium Acrylic Smooth exterior paint with silicone additives of required shade.

New work (Two or more coats applied @1.43 ltr / 10sqm. Over and including priming coat of exterior primer applied @ 0.90 lit./10 sq.m. )

Finishing walls with Acrylic Smooth exterior paint of required shade :

Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall suface to prepare the surface even amd smooth complete.

Finishing walls with textured exterior paint of required shade :

13.45.1 New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm

Providing two coats of SYNTHETIC ENAMEL PAINT of approved shade and make over new WOODEN surface including cleaning the surface after removing dirt, scales, grease and sand papering, including cost of scaffolding etc. all complete as per building specification dirction of E/I.

Providing Primer one coat of read lead paint of approved make over new STEEL SURFACE preparing the surface after cleaning, removing rust, dirt, scales, smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing 2 coats of SYNTHETIC ENAMEL PAINT of approved shade and make over STEEL SURFACE grills & railings including cleaning the surface thoroughly scaffolding and taxes all complete as per building specification and direction of E/I.

MISCELLANEOUS WORK

Providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side the side of waist slab with suitable arrangement as per approval of Engineer-in-charge,(for payment purpose only only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners, etc.)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately).

6 mm thick Cement fiber board as per IS: 14862

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin- charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recomme-nded jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.

Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK.

Providing & fixing on wall face unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110 mm dia

Providing & fixing on wall face unplasticised -P.V.C. moulde fittings / accessories for unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion .

Coupler - 110 mm

SHOE - 110MM

BEND - 110 MM

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

Providing 250 mm wide BRICK DRAIN in cement mortar (1:6) with avarage 150mm. Clear depth and 250 mm apron including cost of earthwork involved with 75m cement concrete (1:4:8) over one brick designation 75A, flat soling in proper grade and slope at the base , the drain dully plastered in C.M.(1:3) with puning over exposed surface all complete as per building specification and direction of E/I.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. (Approved Brand - Tata Bluescope/ Equivalent)

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Ridges plain (500 - 600mm)

Flashings/ Aprons.( Upto 600 mm)

Gutter (600 mm over all girth)

Providing fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Fibre glass wool conforming to IS : 8183, density 48kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags, fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building.

Providing Asbestos sheet ceiling with 120x60mm Salwood beams at 122 cm. c/c and 60X40mm Salwood runners at 122cm centers, including cost of 2 coats of wood preservative paint of approved make, fixing at site and taxes all complete as per approved drawing, building specification and direction of E/I. (Approved Brand - V- BOARD/ BISON)

Supplying and fixing C. I. Cover without frame for MANHOLE. 560MM DIA C.I. COVER (HEAVY DUTY)

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910, on 12 mm dia steel bar confirming to IS: 1786, having minimum cross section as 23 mmX25mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protuded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in tank with 30X20X15 cm cement concrete complete as per design.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape (R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Dismantling pucca brick work including stacking serviceable materialsin countable stacks within 15m lead and disposal of unserviceable materials with all lead, all complete as per direction of E/I.

Dismantling R.C.C. work including stacking serviceable materials in countable stacks within 15m lead and disposal of unserviceable materials with all lead, all complete as per direction of E/I.

Dismantling plain cement or lime comncrete work including stacking serviceable materials in countable stacks within 15 m lead and disposal of unserviceable materials with all lead, all complete as per direction of E/I.

Taking down old door and window shutters including stacking serviceable materials in countable stacks within 15 m lead and disposal of unserviceable materials with all lead, all complete as per direction of E/I.

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : (Of area 3 sq. metres and below)

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : (Of area beyond 3 sq. metres.)

DT: Basic rates for 125/115 mm dia Drilled Tube-well for drilling in all kinds of soil and rock for installation of hand pump with DTH ring Machine all complete including supplying all meterial, labours, tools, drilling, rigs, air compressor and equipments as well as fuel lubricant, for making 125/115 mm dia boring etc. and cost of transporting rig machine and other vehicle up to site of work as per specification and direction of engineer-in-charge. (Basic rates) (i) Drilling up to 30 mtr. Depth below G.L. in Rural Area

Supplying, assembling, lowering and fixing in vertical position in borewell unplasticized PVC medium well screen (RMS) pipes with ribs, confirming to IS: 12818, including hire and labour charges, fittings and accessories etc. all complete, for all depths, as per direction of engineer-in-charge. (100 mm nominal size dia.)

Supplying,filling, spreading and levelling stone boulders of of size range 5cm to 20 cm, in recharge pit, in the required thickness, for all leads and lifts, all complete as per direction of Engineer-in-charge.

Supplying,filling, spreading and levelling gravels of size range, 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in the required thickness, for all leads and lifts, all complete as per direction of E/I.

Constructing brick masonary chamber for Underground C. I. Inspection Chamber and bend with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. Cover with frame (light duty) 455X610 mm internal dimensions, total weight of cover with frame to be not less than 38 KG. (weight of cover 23 kg. and weight of frame 15 kg) RCC top slab with 1:1.5:3 mix (1 cement:1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 mix (1 cement:5 coarse sand :10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm th. with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design:

Inside dimensions 455X610mm and 45 mm deep for single pipe line with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside dimensions 600X850 mm and 45 cm deep for pipe line with one or two inlets : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth beyond 45 cm of brick masonry chamber : (For 455x610 mm size)

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

For 500x700 mm size (With common burnt clay F.P.S. (non modular) bricks of class designation 7.5)

For 600x850 mm size (With common burnt clay F.P.S. (non modular) bricks of class designation 7.5)

Providing and laying non- pressure NP2 class ( light duty ) R.C.C. pipes with collars jointed with still mixture of cenent mortar in the proportion of 1:2 ( lcement : 2 fine sand ) including testing of joints etc. complete.

150 MM dia R.C.C. pipe

250 MM dia R.C.C. pipe

300 MM dia R.C.C. pipe

450 MM dia R.C.C. pipe

Supplying fitting and fixing Galvanised wire mesh of average width of aperture 1.4 mm and nominal dia of wire 0.63 mm (2'-0"x2'-0"*2) in position as per specification and direction of E/I.

Making Soak Pit 2.5 m diameter 3.0 meter deep with 45x45cm dry briick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8m long complete as per standerd design .

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

CARRAIGE OF MATERIALS

LOCAL SAND , LEAD - 2P+1K= 3 KM.

COARSE SAND , LEAD - 9P+1K= 10 KM.

STONE CHIPS , LEAD - 21P+1K= 22 KM.

BRICKS , LEAD- 7P+1K= 8 KM.

SANITARY & WATER SUPPLY WORKS

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast iron P or S trap, 10 litre low level white P.V.C. Flushing cistern with munally controlled device (handle lever) conforming to IS:7231 Parryware/ Hindware with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.

White Vitreous China Orissa pattern W C pan of size 580 X 440 mm with integral type foot rest.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled devicde (handle lever), conforming to IS:7231, parryware/Hindware/with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.

W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

15mm nominal bore

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

15mm nominal bore

Providing and fixing C.P Soap Dish of aaproved size, shape and approved brand with concealed fittings, complete job.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing white vitreous china flat back half stall urinal of 580X380X350mm with white PVC automatic flushing cistern, parryware/Hindware with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass with waste fitting as per IS : 2566 P.V.C. trap with outlet grating and other couplings in C.P. brass including parenting of fitting and cutting and making good the walls and floors wherever required..

Single half stall urinals with 5 litre P.V.C. auotmatic flushing cistern

Deduct the 5 litre P.V.C. auotmatic flushing cistern fron urinal

Sl. No. - 7359. rate = Rs. 477+15% = 558.55

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end )

25MM nominal bore.

32MM nominal bore.

40MM nominal bore.

50MM nominal bore.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete.

25mm nominal bore

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 100mm dia. Steel Jali of approved quality.

Providing and fixing stainless steel A ISI 304(18/8) kitchen sink as per I.S.13983 with C.I. Brackets stainless steel plug 40mm including painting of fittings and brackets cutting and making goods the walls wherever required:

kitchen sink without drain board

610x510mm bowel depth 200mm

470x420mm bowel depth 178mm

Providing and fixing C.P Sink cock with swinging casted spout with concealed fitting arrangements.

Providing and fixing Wall mixer with provision for overhead shower with elbow coupling and wall fiange of standard design and of approved make.

Providing and fixing Pressure adjustable shower with revolving joint with 15mm cp pipe with flange and concealed fitting arrangements.

Providing and fixing Central hole Basin mixer with concealed fitting arrangements.

Providing and fixing unplasticised P.V.C. connection pipe with c.p. nuts collar and bush of approved quality.

15 mm nominal bore with 45 cm length.

Providing And fixing 32 mm waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible Pipe

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (ITEM FOR RAIN WATER, SOIL, WASTE & VENT PIPES)

110 mm dia

Providing & fixing on wall face unplasticised -P.V.C. moulde fittings / accessories for unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion .

Coupler -

Single pushfit Coupler

Single tee with door

Single tee without door

Supplying and fixing 100mm S.C.I. trap with 100mm inlet and 100mm outlet, with all complete.

Supplying and fixing 100mm S.C.I. trap with 100mm inlet and 75mm outlet, with all complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I.(Approved Brand - ASTRAL/ SUPREME)

Concealed work including cutting chases and making good the wall etc..

15 mm nominal dia Pipes

20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes joining of pipes & fittings with one step CPVC solvent cement & testing of joints complete as per direction of E/I. (Approved Brand - ASTRAL)

Exposed on Wall

25 mm nominal dia Pipes

32 mm nominal dia Pipes

40 mm nominal dia Pipes

50 mm nominal dia Pipes

Providing and fixing C.P. brass Health Faucet (Telephonic shower with flexible pipe) including 450 mm long Braided Hoses with all fittings complete job.

Hand Shower - CAT. NO. - JAQUAR, ALD - 573

Providing and fixing C.P. Towel Ring (round) with flange

Towel Ring - CAT. NO. - JAQUAR, AQN - 7721

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.(15mm nominal bore )

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. (15 mm nominal bore)

Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms

ELECTRICAL WORKS

Point wiring in pvc conduit , with modular type switch:-Wiring for light point/fan point/exhaust fan/call bell point with 1.5 sqmm PVC insulated copper conductor cable in surface / recessed PVC conduit with moduler type switch,moduler plate,suitable size GI box etc. as required .

Point wiring in pvc conduit , with modular type switch:-Wiring for light point/fan point/exhaust fan/call bell point with 1.5 sqmm PVC insulated copper conductor cable in surface / recessed PVC conduit with moduler type switch,moduler plate,suitable size GI box etc. as required .

Point wiring in pvc conduit , with modular type switch:-Wiring for light point/fan point/exhaust fan/call bell point with 1.5 sqmm PVC insulated copper conductor cable in surface / recessed PVC conduit with moduler type switch,moduler plate,suitable size GI box etc. as required .

Twin control point wiring in pvc conduit with modular type switch:- Wiring for Twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with 2way modular switch ,modular plate, suitable GI box etc. as required.

Power plug wiring in pvc conduit (2x4 sq mm):Wiring for light/ power plug plug with 2 X 4 sq. mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / sub main wiring in pvc conduit:Wiring for submain wiring with the following size of PVC insulated, copper conductor single core cable in surface / recessed PVC conduit as required:

2x1.5 sq.mm.+1x 1.5 sq mm(for toilet switch board +6A socket)

2x2.5 sq.mm.+1x 2.5 sq mm(for switch board )

2 x 6 sq mm +1x6 sq.mm. (Sub-Mains LDB's)

2 x 10 +1x6 sq.mm. (Sub-Mains PDB's)

4 x 6 sq mm +2x6 sq.mm. (Sub-Mains DB's)

4 x 10 +2x6 sq.mm. (Sub-Mains DB's)

Wiring in existing conduit:-Supplying and drawing following sizes of PVC insulated copper conductor, single core cable in the existing surface/ recessed PVC conduit / PVC casing capping / as required.

2x1.5 sq mm

3x2.5 sq mm (For (Lift)

4x6 sq mm(For Lift)

Supplying & Fixing PVC conduit:-S/F of following sizes of PVC conduit alongwith the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required .

20 mm PVC coduit.

25 mm PVC coduit.

Supplying & Fixing modular type switch / socket :-Supplying and fixing following moduler switch / socket on the existing moduler plate & switch box including connection but excluding moduler plate etc. as reqd.

5/6 amps switch

5/6 amps socket outlet

Telephone socket outlet

Supplying & Fixing modular type electronic fan regulator :- Supplying and fixing stepped type electronic fan regulator on the existing modular plate & switch box including connection but exluding modular plateetc.as required..

Supplying & Fixing modular type blanking plate.:- Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying & Fixing modular boxes,base & cover plate:- supplying and fixing following size/ modules, GI boxSupplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc.as required.

1 or 2 Module (78mmX78mmx45mm)

Supplying & Fixing light plug point with modular type accessories :-Supplying and fixing suitable size GI box with moduler plate cover in the front on surface or in recess including providing and fixing 3 pin 5/6 amps socket outlet and 5/6 amps. moduler type switch, connections painting etc. as required. (For light plugs).

Supplying & Fixing power plug point with modular type accessories :- Supplying and fixing suitable size GI box with moduler plate cover in the front on surface or in recess including providing and fixing 6 pin 15/16 amps socket outlet and 15/16 amps. moduler type switch, connections painting etc. as required. (For power plugs).

Supplying & Fixing S.P. MCB DB :- Supplying and fixing of following way, single pole and neutral, sheet steel, MCB distribution board,240 volts,on surface /recess, complete with tinned copper bushbar, neutral link, earth bar, din bar, interconnections powder painted including earthing etc. as required. (but without MCB/RCCB/Isolator)

4 way double door(ODU)

8 way double door

Supplying & Fixing T.P MCB DB :- Supplying and fixing following way,horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts,on surface /recess, complete with tinned copper bushbar, neutral link, earth bar, din bar, detachable gland plate, interconnections,powder painted including earthing etc. as required. (but without MCB / RCCB /Isolator)

4 way(4+12)double door Horizontal type

6 way (4+18)double door Horizontal type

8 way (4+24)double door Horizontal type

Supplying and fixing 5 amps. to 32 amps. rating, 240 volts10KA, `B' curve, miniature circuit breaker (10 KA) of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

single pole(6 to 32A)

Supplying and fixing 5 amps. to 32 amps. rating, 240 volts `C' catagory, miniature circuit breaker (10 KA) of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

single pole(6 to 32A)

6/32 amps.SPN

32 amps.TPN

40 amps.TPN

63 amps. TPN

Supplying and fixing following ways, surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amp tinned copper bus bar, common neutral link, earth bar, din bar, for mounting MCB's (but without MCB's and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)

4 way (8 + 12 ), Double door, Vertical type

8 way (8 + 24 ), Double door, Vertical type

32 amps.TP

40 amps.TP

63 amps.TP

Supplying and fixing following rating and breaking capacity MCCB thermomagenatic release and terminal spreaders in existing cubical panel board including drilling holes in cubical panel,connections etc as required.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C"curve including connections, painting etc. as required.

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.

1 run of cable

2 run of cable

3 run of cable

Supplying and fixing Modular type socket for CAT 6, as required.

Supplying and drawing following pair 0.5 sq mm FR PVC insulated copper conductor unarmored telephone cable in the existing surface / recessed PVC conduit as required,

TV cable in existing conduit :- Suppyling and drawing co-axial TV cable RG-6 grade 0.7 mm solid copper conductor PE insulated shielded with fine tinned copper braid and protecred with PVC sheath in the existing surface / recessed steel / PVC conduit as reqd.

Supplying & Fixing ding dong sound call bell single phase 230v ,complete as required.

Supplying & Fixing electronic musical call bell single phase 230v ,complete as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade.of following size on wall surface as required.

Upto 35 sq.mm (clamp with 1mm thick saddle.)

Above 35 sq mm and upto 95 sq mm (clamped with 20mmx3mmGI tape)

Laying of PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size exceeding35 sq mm .Direct in ground including excavation ,sand cushioning protective covering and refilling the trench etc as required.

Laying of PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size exceeding35 sq mm but not exceeding 95 sq mm Direct in ground including excavation ,sand cushioning protective covering and refilling the trench etc as required.

Laying of PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size exceeding185 sq mm but not exceeding 400 sq mm Direct in ground including excavation ,sand cushioning protective covering and refilling the trench etc as required.

Laying of one number additonal PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade. of size not exceeding 35 sq mm . Direct in ground in the same trench in one tier horozontztal formating including excavation ,sand cushioning protective covering and refilling the trench etc as required.

Laying of one number additonal PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade. of size not exceeding 35 sq mm but not exceeding 95 sq mm Direct in ground in the same trench in one tier horozontztal formating including excavation ,sand cushioning protective covering and refilling the trench etc as required.

Laying of one number additonal PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade. of size not exceeding 185 sq mm but not exceeding 400 sq mm Direct in ground in the same trench in one tier horozontztal formating including excavation ,sand cushioning protective covering and refilling the trench etc as required.

Supply of PVC/ XLPE Insulated PVC sheathed heavy duty armoured electric cable with alluminium conductor for working voltage upto and including 1100 volts (conforms to IS:1554,part-1)

25 sq mm x 3.5 core

50 sq mm x 3.5 core

70 sq mm x 3.5 core

300 sq mm x 3.5 core

Supplying of PVC / XLPE Insulated PVC sheathed ,heavy duty ,armoured electrical cable with aluminium conductor for working voltage upto and including 1100 volts.(Conforms to IS : 1554,part-1)

16 sq mm x 4core

10 sq mm x 2core

10 sq mm x 4 core

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

2 X 10 sq. mm (19mm)

3½ X25 sq. mm

3½ X 50 sq. mm (35mm)

3½ X 70 sq. mm (38mm)

3½ X 300 sq. mm (70mm)

4 X 10 sq. mm (25mm)

4 X 16 sq. mm (28mm)

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

300 mm width X 50 mm depth X 1.6 mm thickness

LT PANEL (NORMAL SUPPLY) : -INCOMING (1- sets ) each with following:

400 Amp, MCCB FP -2no, 400A Changover FP-01 No, Ammeter, ASS, CTs, Voltmeter, VSS, Fuses, 2 Sets of Phase Indicating Lights with fuses & following accessories: -

BUS BARS

1sets of 500 Amp, 415V, 3 phase, 50 Hz TPN copper bus bars.

OUTGOING

b)25/100 Amp, MCCB FP -8 no

d)6/32 amps.SPN-2no

d)6/32 amps.TPN-4no

e)40 amps.TPN-2no

f)63 amps. TPN-3no

LT Panel (Normal) as above ( L.G.F)

400A MCCB FP

63A 4 pole on load c/o

100A 4 pole on load c/o

400A 4 pole on load c/o

25/100 A, MCCB FP

6/32 amps.SPN

40 amps.DP

6/32 amps.TPN

40 amps.TPN

63 amps. TPN

LED INDICATOR LAMP R/Y/B/G

DIGITAL VOLT METER 500V(3phase class 0.5)

DIGITAL A METER 500V(3phase class 0.5)

CT coil of CT tatio 100/5 IS 2705 part 3

CT coil of CT tatio 200/5 IS 2705 part 3

CT coil of CT tatio 500/5 IS 2705 part 3

50MM*5MM(2.30 KG/MTR)copper strip

25MM*5MM(1.15 KG/MTR)copperStrip

10 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

16 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

6 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

1.5 sq mm ISI marked FRLS PVC insulated single core copper conductor cable

Supplying & Fixing wall floor mounted cubical panel board , fabricated with 16 gauge iron sheet suitable for panel mounted switch disconnector ,incliding busbar chamber,insulator and painting etc.as required .(but without busbar copper strip)

80mm dia earthing electrode 2mtr Length/ 80mm dia earthing electrode 3mtr Length /50mm dia earthing electrode 2mtr Length/50mm dia earthing electrode 3mtr Length and backfill compound chemical 4 bag (per bag 25Kg)

Providing and fixing 8 SWG copper wire (4.0 mm dia)(0.1185kg/mtr).

P/F of lighting conductor finial, made of 25mm. Dia. 300mm. Long copper base plate including holes etc. complete as required.

Rivetting, sweating and soldering of copper/GI tape (with another copper/GI tape base of the finial or any other metallic object) as required.

Providing and fixing GI tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as reqd.(for horizontal run)

Providing and fixing GI tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as reqd.(for vertical run)

Supplying, Installation, Testing & Commissioning of following rating surfface mounted LED tube light fitting suitabe for 230v 50Hz single phase supply etc complete as required

10/12w LED tube light

20/22w LED tube light

Supplying Installation Testing Com of following rating LED post top lamp made in die cast aluminium housing with decotative clear / opal acrylic diffuser on existing pipe including connection with 1.5 sq mm copper conductor etc all complete as required.

20/25w LED post top lamp opel

Supplying, Installation, Testing & Commissioning of following rating appoved make LED bollard fitting with rectangular shape of height 600mm to 850mm power input 8/9w with die cast aluminium housing opel with PC diffuser, IP 65/54 protection confirming to IS 10322 part-5 etc all complete as required.(excluding plinth charge)

Cable junction box

Supplying of conical pole of height 3 mtr with top dia 75mm /as per fitting, Bottom dia 105(+5/-5)mm sheet thickness 3mm and base plate 200x200x12mm with PU painted in different colour as required.

Supplying of foundation bolt of size M-20 600MM

Erection of metallic pole upto 4.5mtr length in cement concrete 1:3:6 (1 cement :3 coarse sand :6 gradedstone aggregate 40m m nominal size )foundation including excavation and refilling etc.as required(3mtr pole)

Supplying of 7 Mtr height octagonal Hot-Dip Galvanized pole (BOP-7030) with top dia 70 mm,bottom dia 130 mm & made of 3 mm thick sheet ,base plate diamentions 200 MM X 200 MM X 12 MM (LxBxT) including suitable size of foundetion bolt and 1'6'' long 50mmX50mm MS angle along with welded horizontally on top of octagonal pole all complite on exiting concreat platform as required

Supplying and fixing of 1.5 mtr single arm suitable for 70 mm top

Supplying and fixing of 1.5 mtr Double arm suitable for 70 mm top

Installation,testing and commissioning of the 9mtr octagonal pole and light fitting with the help of suitable tools and plants ,wiring of luminaires with all materials and construction of shallow foundation with M25 grade concrete considering safe soil bearing capacity of 10T/mtr sq.

Supplying, Installation, Testing & Commissioning of following rating recess/ surfface mounted LED round /square shape down light luminaierewith pressure die cast housing for single phase supply voltage luminarie shall be confirm to IS:10322 part-5/section 2 or IEC :62722 with all necessary accessories as required.

12w LED round down light.

18/20w LED round down light.

2"x2"LED panel light

Supplying, Installation, Testing & Commissioning of following rating LEDstreet light luminaiere with pressure die cast housing and toughend glass cover (IP 66 protection )in xisting pole/pipe for supply voltage 100-270 AC 50 Hz luminarie shall be confirm to IS:10322 part-5/section 3and shall be complete with all necessary accessories as required.

90/100W LED street light.

120W LED street light.

Supplying, Installation, Testing & Commissioning of following size ceiling fan 3 blades confirming to IS-374:2019including wiring the down rods of standared length (upto 30 cm)with 1.5 sq mm FR PVC insulated copper wire suitable for 230v 50Hz single phase supply etc.as required.

1200mm (48")BLDC 5 star rating 32w Ceiling fan

1400mm (56")BLDC 5 star rating 32w Ceiling fan

9" (230) mm )metal exaust fan

12" (300) mm )metal exaust fan

15" (380) mm )metal exaust fan

16" Wall mounted fan

Providing of bulkhead fitting with 9/10w LED bulb.

450 mm (18") Metal body Wall fan with speed regulator suitable for single phase 220v ,50Hz,AC supply.

Supplying & Fixing 2 pin 5A ceiling rose on the existing junction box wooden block including connection etc ,as required.

Supplying & Fixing batten / angle holder including connection etc as required.

Erection of wall bracket / ceiling fittings of all sizes and shapes ontaining upto two GLS lamp per fitting complete with all accessories including connection etc as required.

Installation of exhaust fan upto 450 mm. sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connections, testing, commissioning etc. as required.

Providing, supplying, testing and commissioning Silent type D G Set capacity of 100 KVA with AMF panel IS/ IEC-60034-1 IS:1460 IS 13018 including all accessories and all fittings complete job.

Supply and laying 8 SWG copper wire at 0.50 metre below ground level for conductor earth electrode, including solding etc. as required.

Providing and fixing 6SWG GI wire at 0.50 m below ground level for coductor earth electrode,including soldering etc as required.

Digital Timer and controller and 60A 4 Pole 3 output (1 out put per phase) and suitable for three phase supply.

Cubical type panel board, fabricated with 14 guage iron sheet suitable for panel mounted SFU/MCCB and complete with bus-bar chamber, insulator, nut-bolt with MS 40 X 40 X 5 mm angle stand and complete with powder painting etc as required. ( But without busbar copper strip)

BOREWELL

200/150 mm dia Deep borewell : Cost of drilling 200 mm X 165 mm X 125m deep brewell in all kinds of soil and rock in rural area for installation of pump set with Hydraulic DTH Rig machine, all complete including supplying all all materials, tools drilling rig, Air compressure and equipments, as well as fuel, lubricants and cost of transportation of Rig machine and other vehicle up to the site.

(a) From 0.00 M to 50.00 M below G.L

(b) From 51.00 M to 125.00 M below G.L

(c) From 125.00 M to 200.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

200mm Nominal size dia.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm Dia.

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

Supplying 100mm dia. Submersible pump sets confirming to IS 8034 and motor cvonfirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft ant polypropylene/ norylimpeller. Motor suitable for working on 415 V+10%, 3PH, 50 HZ, AC supply with cable guard, thurst carbon/ fibre bearing to withstand entire hydraulic thrust, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as per manufacturers design. Anti thrust stream lined no return valve shall be provided with pump. 3 m submersible copper conductor cable in single/ double run and nylon rope as required length shall be provided with each pump.

Submersible pump set 100mm dia (with polypropylene/ Noryl Impeller) 2 HP

Supplying and fitting of standared make starter pannel board with arrangement of all necessory protection ,including all taxes , royalty etc all complete job as per direction of E/I 5 HP TO 10 HP

Supplying ,fitting & fixing & connecting 3 core 4 sqmm flat copper submerssible cable of Finolex / Hevels make including all taxes ,royalty etc all complete job as per direction of E/I

Supplying and laying /lowering of GI pipe of 50 mm dia including of required fittings solvent etc complete job as per direction of E/I

LANDSCAPING WORKS

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% for payment).

Supplying and stacking at site dump manure from local or other approved source including royalty and cariage up to 1 km. (Manure measured in stacks will be reduced 8% for payment). Screened through sieve of I.S. designation 4.75 mm.

Rough dressing the trenched ground including breaking clods.

Fine dressing the ground

Spreading of sludge, dump manureor / and good earth in required thivkness(Cost of sludge, dump manure or / and earth to be paid seperately).

Mixing earth and sludge or manure in proportion specified or directed.

Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Callistemon lanceolatus of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Ficus bengalensis (varigated) of height 75-90 cm., multibranched in earthen pots of size 30 cm as per direction of the officer-in-charge.

Providing and stacking of Polyalthia longifolia (Ashok) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge.

Dreaceana pendanus, well developed, having 6 to 8 suckers with helthy foliage in 25 cm size Earthen pot /Plastic pot

Dianella variegated, with 3 to 4 variegated leaves in 20 cm size of Earthen Pot / Plastic Pot.

Euphorbia milli hybrid variety, having ht. 30 cm to 45 cm with multi branch, full bloom, fresh and healthy leaves in 30 cm size of Earthen Pot / Plastic Pot.

Adenium Obesum well developed with fresh & healthy 4 to 5 branch 60 to 75 cm ht. plant in 40 cm size Earthen Pot/ Plastic Pot

Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot / Plastic Pot.

Dracaena Mahatma having ht. 30 cm to 45 cm, well developed, fresh and healthy foliage in 20 cm size of Earthen pot / Plastic pot.

Providing and stacking of Butea frondosa (Flame of Forest) of height 60-75 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Foxtail Blue palm/ Fan palm of ht. 180-210 cm bottom girth 25-30 cm well developed in big size HDPE bags as per direction of the officer-in-charge.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes joining of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of E/I. (Approved Brand - ASTRAL)

Exposed on Wall 25mm dia

FIRE FIGHTING WORKS

Supply, Installation, Testing and Commissioning of electric driven, centrifugal type, single/multistage, end suction type, centrifugal pump of cast iron body, C.I impallers with carbon steel shaft & mechanical seal directely coupled with TEFC SQ cage foot mounted type induction motors suiitable for operation on 3 phase, 415 volts 50 Hz AC with IP 55 Protection for enclosure, horizontall foot mounted with class F insulation , complete in all respect as required or as directed by engineer incharge.

Main Fire Pump

Standby Deisel Engine Pump

Jockey Pump

Terrace Booster Pump

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42.

For Pump Room

Supply and fixing of PVC sheathed following conductor 1.1 KV grade armoured Cable of following sizes including making end termination with compression gland & bimetalic lugs, and support etc.complete as required

3.5 × 50 sq.mm.(aluminium)

4 × 10 sq.mm.(aluminium)

2 × 2.5 sq.mm.(Copper) to be laied in 5 pairs for engine

Providing and fixing IS marked Gate Valve / Foot Valve (incase of -ve suction) complete with companion flanges, bolts, nuts, rubber insetions etc.

200 mm diameter

150 mm diameter

Providing and fixing IS marked butterfly valve (PN 1.6) complete with companion flanges, bolts, nuts, rubber insetions etc.

80 mm diameter

100 mm diameter

150 mm diameter

Providing and fixing check valve (NRV) complete with companion flanges, bolts, nuts, rubber insetions etc.

80 mm diameter

100 mm diameter

150 mm diameter

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing, laying, testing & commissioning of IS 1239 marked black M.S pipe including all fittings i.e bend, elbows, tees, flanges, reducing socket, nuts and bolts, gaskets etc fixed with welded / screwed joints. including necessary excavation, backfilling, removal of surplus soil etc. min. 1 mtr deep excavation and wrapping with anticorrosive treatement with 4 mm thick asphalt tape as per IS:10221, refilling the trench etc. OR fixed with screwed or welded joints, hanged with clamps, hanger supports, dash fasteners, bolts, nuts, rubber insertions etc including threading, cutting, welding, edge preparation, painting of approved colour over two coat of primer, cutting & making good the wall/ floor wherever required, complete as required or as directed by engineer incharge.

200 mm diameter

150 mm diameter

100 mm diameter

80 mm diameter

25 mm diameter

Providing and fixing S.S Fire Hydrant Valve of approved quality with 63 mm female, instant, ovlique, single outlet, 80 mm flanged inlet, brass spindle, cast iron wheel m A.B.S. blank cap and chain. conforming to IS: 5290 complete with companion flange, bolts, nuts, rubber insertion / compressed asbestos gasket etc. and painted in fire red colour.

Providing and fixing swinging, wall mounting type First Aid Hose Reel of approved quality and made from compresed steel sheet with dust cover, cast iron brackets including 30 m long, 19 mm nominal bore, high presure braided rubber hose as per IS:444 Type hose guide, PVC shut off nozzle with 6 mm outlet and 25 mm nominal bore gun metal inlet valve, bolts, nuts rubber insetion etc. painted in Fire red colour including cutting and making good the walls wherver required.

Providing and fixing in position 63 mm nominal bore and 15 m long synthetic fibre, CP fire hose pipe of approved make bearing IS: 636 -1988 type A mark and having TAC and MMD approved with a pair of 63 x 63 mm gun metal instantaneous type, heavy duty delivery hose coupling (conforming to IS: 903) bound and riveted to the hose pipe with copper rivets and copper wire complete.

Providing and fixing in position short SS brach pipe of approved quality with 63 mm male instatneous type inlet and 15 mm outlet nozzle complete conforming to IS : 903

Supplying, fixing, testing & commissioning of 1 set of 63mm two way instantaneous fire brigade connection (FBC) with inbuilt NRV comprising of SS and four SS instantaneous male inlet coupling confirming to IS:604 with plug and cap with chain as required with nut & bolts, washers, high pressure gasket as required.

Supplying, installation, testing and commissioning of optical type Smoke detector and mounting base with LED light complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed having two LED with cover complete with all connections etc as required

Supplying, installation, testing and commissioning of duel tone electronic hooter / Flasher / Strobe suitable for wall mounted complete as required.

Supplying, installation, testing and commissioning of manual call box in suitable enclosure with arrangement to raise the alarm when the glass is manually broken complete as required.

Supplying, installation, testing and commissioning of microprocess base main fire alarm control panel with LCD Display lights. The panels shall have 240 volts AC power supply automatic Battery charger 24 Volts sealed lead acid maintenance free battries as complete with batteries, battery charger illuminated numeric digram complete as required.

Providing and laying 19mm dia PVC conduit complete with required junction boxes in recessed / surface system with PVC insulated copper conductor cable of 2x1.5 sq.mm. in existing conduit as required.

AIR-CONDITIONING WORKS (SPLIT AC)

Supplying, installations, testing and commissioning 1.5 Tr Inverter Split AC with 5 star rating, which includes low power consumption and as it is an inverter based technology i.e. will expand its cooling capacity according to the room temperature having 100% copper tube, Superslit Find and also have smooth air and clean air flow features with cooling system, Intelligent Defrost mode including drain pipe, copper pipe of required length, outdoor ms stand (painted) as required and complete job. Approved Brand - Hitachi/ Daikin/ Voltas/ Toshiba.

Supplying, installations, testing and commissioning 2.0 Tr Inverter Split AC with 5 star rating, which includes low power consumption and as it is an inverter based technology i.e. will expand its cooling capacity according to the room temperature having 100% copper tube, Superslit Find and also have smooth air and clean air flow features with cooling system, Intelligent Defrost mode including drain pipe, copper pipe of required length, outdoor ms stand (painted) as required and complete job. Approved Brand - Hitachi/ Daikin/ Voltas Toshiba..

Copper tube of size 1/4"for split ac unit 1/1.5/2/3 tr capacity including nitride rubber insulation.

Copper tube of size 1/2" for split ac unit 1/1.5/2/3 tr capacity including nitride rubber insulation.

5 KVA wall mounted automatic voltage stablizer from range 140v to 280v .

Drain pipe for AC

Outdoor stand for 1/ 1.5tr split AC.

Outdoor stand for 2 tr split AC.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Providing supplying and installing Armstrong "Optra Acoustical Wall Panelling" with square edge made of fibre glass subtrate 25mm thick and wrapped on the front side with an acoustically transparent and fire resistant fabric with an option of colours as per the choice of the Architect of size 2100x600 or 600x600mm providing a minimum sound absorption level of 0.90 NRC to be affixed to wall using wall panel impalers including fixing of panel to the wall surface by self taping screws. Silica based construction adhessive shall be dabbed on to the prjecting elements (spikes) of the impalers and panels shall be pierced through the spikes with maintaining the line and level of panel Approved Brand - Armstrong/ Anutone)

Supplying & Fixing of Manufacture, Supply, of polycarbonate multi-layered, Multicell Connectible modular panel system, a complete assembly of coextruded UV protected polycarbonate panels incorporated into a complete system. Standing seam polycarbonate panel system of minimum 16mm thick (Min.) Panels shall be with grip lock double tooth locking mechanism with interlocking connectible connectors running lengthwise at both sides of the panel. Panels shall be fixed on Purlins of MS structure (will be paid Separately) with 3 numbers of self-drilling screws and trapezoidal SS fasteners. The Trapezoidal SS fasteners shall have a base coverage of minimum 40mm and top holding of 80mm across length on polycarbonate panel to ensure a pull-out load of min. 7000N (7KN) tested as per ISO 6892:1998 and IS 1608: 2005.

Panels shall be solo opaque type in opaque and translucent clear combination with six layers to get required lux level along with all fixing accessories to ensure best performance for wind uplift, vibration, oil canning and visual appearance. Panels with more layers will be preferred for better insulation and improved shading coefficient. U value shall not be more than 2.1 Watt/m2K as per EN ISO 1077-2:2018 and respective third-Party test certificate shall be produced before procurement. Panels must satisfy Dart drop impact test as per IS 14443-97 shall show no sign of breakage on Polycarbonate sheets which have been exposed to UV for a min. of 500 Hours as per ASTM G 155.Panels shall not have Yellowness Index as per ASTM D 1925 of 15 units when tested on a sample exposed to UV for 500 Hours as per ASTM G 155. Panel shall be with additional End cap/Aluminum U/F profile/ Glazing Bar (all aluminium shall be factory / mill finish) for ends as required. Panel shall be fixed over MS structural steel/MS purlin conforming to the detail technical specifications as per approved architectural drawings. Trained and factory authorized labour with supervision to complete the entire panel installation as per drawing and direction of the engineering in charge.

Color: As per Approval. Approved Make: Flux/ DPI Daylighting over false ms structure with 72 mm x 72 mm / 60 mm x 60 mm square hollow pipe , 100mm x 100mm post with all fitting fixtures like plates, bolts, complete.

Providing and fixing Roller Blind as per approved material (VISTA LEVELLOR) including all fittings and labour, complete job.

Providing, Supplying and installing Potable water purification system with inbuilt water cooler & RO system with stainless steel (304G) 120 ltrs water storage capacty & 2 tap, fully automatic, including all complete. (Brand; Blue Star (NST80120B)/ Equivalent)

Providing, Supplying and installing Aquaguard UV ABS grade plastic Drinking Water With Built In Water Purifiction System (Aquaguard 200 Water Purifiers) including all complete. (Brand Eureka Forbes/ Equivalent)

Providing and fixing C.P. brass concealed Stop valve of standard design and of approved make conforming to IS:8931. - 20 mm nominal bore. (Approved brand - ESCO/ Jaquar/ Equivalent)

Supplying outdoor type copper wound transformer continuosly rated for 3ph 50Hz at full load and temp.rise not exceeding 450 c by thermometer in oil and 500c by the resistance in winding after continuous run at full load rating ,the transformer should have oil unmersed winding having vactor group DY11 HT side connected in delta and LT sideconnected in star with neutral brought out connected to provide separate earthing .The transformer shall have power terminal arrangenent bushing / cable end box on HT side and cable end box on LT side 2 nos channels with stoppers shall be provided and fix on the provided plinth for mounting the transformer .The transformer should have following standard fitting.Transformer shall be latest manufacturing standards as per amended IS specification and the load & No load losses shall be limited to the values given below or as per IS 2026 or norms issued by SEB which ever are lower.

Oil conservator with filling hole with cap and plain oil level gauge.

Silica gel dehydrating breather charged with silica gel

oil drain valve

Lifting eyes / hooks

Two earthing terminals

Digram and rating plate

Air vent

Explosion vent

100 mm dia thermo meter with thermometer pocket

Four bi directional plain rollar

Power transformer 11000/433V with off load tap changer -12.5% to +2.5% in steps of 2.5% per BIS leveel-2

200KVA (No load loss 500w and load loss 3000w)

6/32A Auto C/O 2 Pole

Providing and fixing 12v 75w solar panel & 30w luminary with 12v -30AH battery,2.5 sq mm 2 core cable for self mounted fixing 6 mtr ht.m.s.pole fixed on ground with concrete as per required.including all hardware and accessories complete.

For Terrace Pump

Pressure Gauge Assemble with Gate/Ball Valve

Air release Valve / Drain Valve

MS Structure support for piping

Providing and fixing 25 / 15 mm nominal gun metal gate valve class I with CI wheel of approved quality with union (Screwed end)

Supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect.

Providing , fixing Dry Chemical Powder (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (4 Kg Capacity)

Carbon Di-oxide Type , Gas Confirming to IS ‘15222’ , Cylinder Confirming to ‘IS 7285’ & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ‘IS 15683’ & ‘IS 2878’ ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)55oC Suitable for ‘B’ ‘C’ Class of FIRE (4.5 Kg Capacity)

Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (5 Kg Capacity)

SOLAR POWER GENERATION

SOLAR POWER GENERATION WITHOUT BATTERY POWER BACKUP AREA OF ROOF FOR SOLAR PANEL = 3,950.00 SQ.FT. NO. OF KWA @ 1KWA PER 100 S.FT. NO. OF KWA =39.5.00 KWA = 40 KWA (WORK TOBE DONE THROUGH JEREDA, NOT FOR TENDER)

FURNITURE WORKS (SRC & AUDITORIUM)

GODREJ INTERIO Powder Coated MS 6 Seater Restaurant Table. Shape of Table-Rectangular, Seating Capacity-6, Material of top, Medium density fiber board, Material of understructure, Powder Coated MS, Material of top finish. Polyurethane, Length of table ±10mm (Diameter in case of Round) 1600 mm, Depth of table ±10mm- 1100 mm, Thickness of top in mm (+/- 5%)-25 mm, Warranty period in number of years-1-year

Nilkamal Restaurant / Cafeteria Chair with frame of SS 304 and Plastic moulded seat. Chair Armrest Without. Type of seat-Plastic moulded. Seat Cushion-Without, Back Rest Cushion-Without, Upholstery- N.A, Material of frame-SS 304, Chair height (overall) ±10mm-900mm, Backrest width ±10mm-450, Width of seat ±10mm- 450, Depth of seat in mm (+/- 10 mm)-525, Height of seat in mm (+/- 5 mm)- 450, Seat Finish- Injection moulded high impact strength polypropylene polymer compound with indoor grade UV resistance.

Total Number of Seats in the Sofa Set 2. Type of Sofa and Backrest Seat and Backrest are permanently fixed with the frame Structure. Frame Covering Fully Upholstered. Backrest Cushion Material Foam. Density of Cushion of Backrest Material (Kg/Cubic M)40. Covering Material for Seat and Backrest Leatherite. Frame Structure Material and size (±1 mm) Any other wood of minimum 25 mm thickness. Seat Cushion Material Foam Density of Cushion of Seat Material ±3 (Kg/Cubic M)40. Type of Spring in the Base / Seating No Spring in the Base

Supplying and placing of Center Table,Material & Subtype Solid Wood - Beech Wood Frame Material-Solid Wood Leg Material-Solid Wood Finish-Matte Colour & Colour Family Brown - Walnut Dimension-(W)1130mm X (D)630mm X (H)410mm,The product must be from a Manufacturer having ISO 9001,ISO 14001,,AIOTA ,BIFMA COMPLIANT, GREEN GUARD,SEDEX CERTIFICATE. MAKE ..WARRANTY-5YEARS.MODEL NO-HOPPER/CT

Executive Table of prelaminated MDF board 1500 millimeter 600 millimeter 750 millimeter (DWS/34723)

Executive Table of Three layerprelaminated particle board(Wood Product) ofgrade II type II of IS 12823/Latest 1500 millimeter700 millimeter 725 millimeter . (DWS/34752)

Revolving Chair With Arm Synchronic tilt mechanism. (70008/MB/STANDARD)

GODREJ INTERIO Revolving Chair With Arm Centre pivot mechanism GODREJ INTERIO (Godrej Interio Oxbo MID BACK CHAIR)

DURIAN Non-Revolving and Non-Tilting chair with Armrest DURIAN (ANJIS/32002)

Anand steel Rectangular Only two leg members widthwiseand one leg member to adjoining each other - with 100 mmground clearance Classroom Tables Anand steel

DURIAN Modular Work Stations with Four Seater Rectangular Cluster with Straight Line Side by Side Sitting

DURIAN 900 mm wide 2000 mm high Metal Shelving Racks DURIAN (Galvin)

DURIAN Modular Work Stations with Double Seater Rectangular shape Cluster with Side By Side sitting

NAVNEET ENTERPRISE Portrait/ Landscape Not applicable Fabric Pin Up Notice Boards NAVNEET ENTERPRISE (Fabric Pin Up Notice Boards 3 X 6 FT GREEN)

DURIAN AUDITARIUM CHAIR 450 millimeter 440mm seat with auto tip up mechanism with push back feature

DURIAN Wooden Podium design Gable end and modesty panel and top material MDF board of grade SBG II of IS 12406/Latest

FURNITURE WORKS FOR INNOVATION HUB

Overall Dimention: 1500x750x750 mm Ht. Top made of pre laminated particle board with pvc edge beading. Understucture also made up of pre laminated particle board with pvc edge beading. Top- Size :- 1500x750x25 MM thk. Pre Laminated Particle Board. Side edges covered by 2 mm thick PVC Edge beading by Through Feed Machine. Modesty- Modesty made up of 18 MM thk. Pre Laminated Particle Board. Open edges covered by 2 mm thick PVC Edge beading by Through Feed Machine. Under Structure- Side Leg made with a Combination of 25 MM thk. Pre Laminated Particle Board with Aluminium section of size 60X40 with grooving. Leg/Side Base & Top plate with profile cut made of M.S. plate 44 mm width & 4 mm thk with knock down fitting arrangement. Cable duct made up of 0.8 mm CRCA Sheet. Provision of Cable manager as per L.H. or R.H. side requirement. Open edges of Particle board covered by 2 mm thick PVC Edge beading by Through Feed Machine. Side Table- 1200x500x715 mm. Storage Size:- W:450xD:400x600 mm Ht. Top made of 25 mm thick Prelaminated Particle Board. Under structure made of 18 mm thick Pre Laminated Particle Board. Open edges covered by 2 mm thick PVC Edge beading by Through Feed Machine. Wooden Pedestal- Size: Height:650mm, Width:400mm, Depth:450mm Top made of 18mm thick Prelaminated Particle Board. Side ,back and drawer front are made by 18mm thk. Pre-laminated Particle Board. Metallic finish heavy duty handle. Superior quality make front mounted lock. Special drawer slides for filing drawer. Other drawers on roller slides. Cap & Levellers- 6 nos of flat type leveller has been provided at bottom for mentaining level. It also preventing scratches on floor & Product as well. Construction- The product comes in knock-down conditional for ease of transportation.

Finish- No sharp edges in the prodect. All steel components are epoxy powder coated followed by seven SDU with Drawer with Top Length 1300mm- Size: Height:750mm,Width:900mm,Depth:450mm Body part made-up of prime quality CRCA Sheet Use only MIG/TIG & Spot welding for fabrication. Top made of 18mm thick PLPB. Side Edges covered with PVC edge band on edge bending machine. Provision of drawer below table top with telescopic channel. Door set make lock. PVC/ Aluminium handles. Doors in PLPB/CRCA M.S. Sheet. Doors are Top hung slide on roller bearing. All steel components should be epoxy powder coated followed by seven tanks anti corrosion treatment of surface. The overall appearance of the product shall be as per photograph.

Yuwa Mesh Hi-Back- Specification- Size-H:1130-1230mm, Seat ht: 470-570mm, D-680mm, W-600 mm. 5-Prong nylon base for stability. Twin Wheel heavy Duty Castor for easy mobility under load. Seat Hot pressed ply wood with steel T-Nuts for rigid fastening with PP cover. Back is moulded Bright Bar with stitched Mesh Cloth. Sturdy steel column gas lift for centre support and seat height adjustment. Telescopic ABS cover over steel column. Lockable synchrony tilt mechanism and with Single piece Die castes PP arm rest adjustable with PP pad. Quality tapestry. High density Moulded PU cushion.

Yuwa Mesh Low Back- Specification- Size-H:930-1030mm, Seat ht: 460-560mm, D-680mm, W-580 mm. 5-Prong nylon base for stability. Twin Wheel heavy Duty Castor for easy mobility under load. Seat Hot pressed ply wood with steel T-Nuts for rigid fastening with PP cover. Back is moulded Bright Bar with stitched Mesh Cloth. Sturdy steel column gas lift for centre support and seat height adjustment. Telescopic ABS cover over steel column. Lockable synchrony tilt mechanism and with Single piece Die castes Fixed PP arm rest . Quality tapestry. High density Moulded PU cushion.

Providing and placement of 3 seater sofa with Overall Size 1920mm(W) 770mm(D) 730(H). Seat Ht 450mm. Handle Ht- 620mm. Upholstery Material: Premium Quality Pu Cloth/Leatherite. Frame Material : Combination of plywood and pine Wood, Plywood thickness : 12 mm (moisture resistance and termite free) & 3 mm. Pinewood cross section - 22x64 mm. Moisture content: 10-12%. Seat Material : 45 mm thick U foam, Density : 32. Super soft 45 mm at top. Dacron 150GSM. Back Material : 45mm thick U foam, Density : 28. Super Soft 45 mm. 22mm thick U foam, Density : 28. Outer foam 10 mm thick, Density 28. Dacron 150 GSM. Fitted with 75 mm wide elastic belts. S/Zick Zack Spring of dia. 3.8 mm mounted on seat structure using Metal mounting clip. Legs : Prime quality Metal, Ht. 150mm.

Providing and placement of 2 seater sofa with Overall Size 1350mm(W) 770mm(D) 730(H). Seat Ht 450mm. Handle Ht- 620mm. Upholstery Material: Premium Quality Pu Cloth/Leatherite. Frame Material : Combination of plywood and pine Wood, Plywood thickness : 12 mm (moisture resistance and termite free) & 3 mm. Pinewood cross section - 22x64 mm. Moisture content: 10-12%. Seat Material : 45 mm thick U foam, Density : 32. Super soft 45 mm at top. Dacron 150GSM. Back Material : 45mm thick U foam, Density : 28. Super Soft 45 mm. 22mm thick U foam, Density : 28. Outer foam 10 mm thick, Density 28. Dacron 150 GSM. Fitted with 75 mm wide elastic belts. S/Zick Zack Spring of dia. 3.8 mm mounted on seat structure using Metal mounting clip. Legs : Prime quality Metal, Ht. 150mm.

Overall Dimension: 600x600X 450 H mm • Made up of 25mm Thick Prelaminated Partical Board • One side laminated, Color matching to running Color Scheme. • Edges finished with 2mm self glued hot pressed PVC Edge Biding by Rehau or equivalent. • Base will be in Trirod Pattern as shown in image • Made up of mild steel round bright bars finished with Powdercoating • Powder coating of all the metal units must be of 70 micron tank process with oven baking coat by polyster powder coating. • Partical – Associate Brand or Equivalent.

Overall Dimention- L-1350mm, D-1050mm x H-750mm, Table ( Set of 2 Table without Chair), Top made of 25mm thick HDMR board with 2 mm thick PVC Edge beading by Through Feed Machine. Legs made of CRCA Tube Dia-32mm x 1.6mm thick, Frame Bush Dia-38mm x 2.5mm thick, Horizontal Tie Member CRCA Pipe-50mm x 25mm x 1.2mm thick. All steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface. The overall appearance of the product shall be as per photograph.

Size:-Overall H: 835mm,D:585mm,W: 520mm: - Back & Seat Moulded Cushion • Back Outer PPCP • Crape Tapestry • PU Handle • Hot pressed Ply • Frame Oval Tube 13*31 mm-16g With Powder Coated.

Lab Table for Robotics with Top Scurting 4 Inch, 18mm thick- Overall Size:- Length:2400, Width:- 1200mm, Height:-900mm. Top made of 25mm thick pre-laminated particle board. Round Edges covered with PVC edge band on edge bending machine. Body Size : - L-1800 x D-600 made-up of 0.8mm, Thick prime quality cold rolled close annealed sheet use only MIG/TIG & Spot welding for fabrication. Providing 02 nos. of Sliding Door made of 0.8mm Thick CRCA Sheet. One adjustable shelf inside storage & Locks Ebco / Doorset cylindrical.All steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface.

Lab Table - Overall Size:- Length:2400, Width:- 1200mm, Height:-900. Top made of 25mm thick prelaminated particle board. Round Edges covered with PVC edge band on edge bending machine. Body Size : - L-1800 x D-600 made-up of 0.8mm, Thick prime quality cold rolled close annealed sheet use only MIG/TIG & Spot welding for fabrication. Providing 02 nos. of Sliding Door made of 0.8mm Thick CRCA Sheet. One adjustable shelf inside storage & Locks Ebco / Doorset cylindrical.All steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface. With 2 Popup box of 8 Module ( Note- Without Switch & Socket)

Lab SDU- Size:-Length:1200mm, Width:- 750mm, Height:-900mm, Storage depth is 560 mm & top overhang by 190mm at front. Body part made-up of prime quality cold rolled close annealed Sheet Use only MIG/TIG & Spot welding for fabrication. Top made of 25mm thick pre-laminated particle board. Side Edges covered with PVC edge band on edge bending machine. One adjustable shelf inside storage. Locks Ebco / Doorset cylindrical. All steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface. The overall appearance of the product shall be as per photograph.

Desk Mounting Cable Duct- Size:- Length:1200mm Thickness: 70mm, Height: 150mm, Duct-70mm Thick Tiles Base PartitionInternal Frame are made by 1.6mm thk. cold rolled close annealed powder coated Sections. Tiles are made by 12mm. Thk. Pre laminate particle board. Frame structure are fabricated by MIG/TIG welding Machine. Tiles are fitted by high strength PVC Dowel in PVC Insert with transition fit. provision of Slot for cabling and accessories. upper and side trim are 1mm thk. extruded powder coated aluminium section and Pole is 1.6mm Thick Aluminium.

AL-02GD- Size:-height:1980mm, width:910mm depth:380mm Body part made-up of prime quality cold rolled close annealed Sheet Use only MIG/TIG & Spot welding for fabrication.5 adjustable shelf. Three way locking device with six levers superior quality lock for Door . Doors made of press formed MS cold rolled close annealed sections with 4mm glass. Doors are mounted on steel hinge brackets. All steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface. The overall appearance of the product shall be as per photograph.

Lab Table Without Bottle Rack (Single Side Unit)- Lab work table without bottle rack single side usable, Size-W:1200mm x D:600mm x Ht:900mm.The frame made of MS cold rolled close annealed tube, vertical leg made of 25x25x18G(1.2mm), and horizontal tie member made of 25x50x18G(1.2mm). Top made of black granite 17mm thk and black granite supported on fibber cement board 10mm thk. Bottom storage over all size- w-1150mm x Ht 845mm x D450mm.made up of Prime quality MS cold rolled close annealed sheet 0.8mm thk. One adjustable self creating two compartment. Doors with top hung sliding mechanism, slides on PVC rollers. Lock Ebco/Doorset. Handles die cast PVC. SDU mounted on heavy duty brack castors of zipco make. Provision for one Gas Burner with connection. Light and other arrangements are optional. All steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface. Powder coating thk.50-60 micron.

Sink Table:- Height: 900mm, Width:600mm, Depth: 600mm. The frame made of MS cold rolled close annealed tube. Fabrication involves only MIG welding process. Top- Top made of black granite 17mm thk and black granite supported on fibber cement board 10 mm thk. Understructure- The frame made of MS cold rolled close annealed tube, vertical leg made of 25x25x18G(1.2mm), and horizontal tie member made of 25x50x18G(1.2mm). The door made of press formed cold rolled close annealed sheet fitted with cylindrical hinge with provision to hang the door with frame. Sink- The sink made of Highly Chemical resistant & Longlasting Polypropylene. Tap- Tap made of high quality Brass & Knob made up of High quality Polypropylene, Tap is epoxy fusion powder coated. Levellers- 4 nos of flat type leveller has been provided at bottom for mentaining level. It also preventing scratches on floor & Product as well. Construction- The product comes in knock-down conditional for ease of transportation. Finish- No sharp edges in the prodect. All steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface.

Over Head Storage unit with Glass Door,- Size Length-1200mm, Depth-400mm, Height-600mm, Made Of 18mm thick Pre-laminated Particle Board. Door are made by aluminium profile with 4 mm glass.

Supplying and Fixing Office Table 1200mm W X 750mm D X 740mm H WorktopMade from 25 mm Thick Pre-laminated Particle board. All the edges are sealed with 2 mm thick PVC edge band all around, Understructure PLB made of 18 mm thick pre laminated particle board. with Fixed Pedestal.

Specification- Size-H:930-1030mm, Seat ht: 460-560mm, D-680mm, W-580 mm. 5-Prong nylon base for stability. Twin Wheel heavy Duty Castor for easy mobility under load. Seat Hot pressed ply wood with steel T-Nuts for rigid fastening with PP cover. Back is moulded Bright Bar with stitched Mesh Cloth. Sturdy steel column gas lift for centre support and seat height adjustment. Telescopic ABS cover over steel column. Lockable synchrony tilt mechanism and with Single piece Die castes Fixed PP arm rest . Quality tapestry. High density Moulded PU cushion.

Top Length: 1200 mm, Top Width: 600 mm, Top Height: 750 mm. Top material 18mm thick prelaminated Particle board. All open sides of the top must have post forming on min. 2 sides, with 2mm thick PVC edge banding with hot melt glue where post forming is not practicable. Top thickness: Minimum 18 mm, Maximum 20 mm Understructure can be of mild steel ERW or of prelaminated wood. Understructure, if metal shall be covered with PVC or similar cladding material Accessories: Lockable drawers and closet with door to be provided, with depth equaling the width of the top and combined height of drawers and closet approximately equaling the height of top. Drawers should each have minimum 30 kg load bearing capacity and have telescopic ball bearing drawer channel for full depth; footrest; Modesty Panel to be in front to ensure privacy; to be of material same or superior as top board Refer guiding image in Annexure C for reference.. Remark: . Top- Size :- 1200x600x18 MM thk. PLPB , Side edges covered by 2 mm thick PVC Edge beading by Through Feed Machine. Modesty- Side modesty made up of 0.8 MM Thk. CRCA sheet perforatted panel. Front Modesty made of 18 mm PLPB. Understructure vertical tube sof 50 x 50 mm. Edges are rounded. Top height 750 mm

Yuwa Mesh Low Back- Specification- Size-H:930-1030mm, Seat ht: 460-560mm, D-680mm, W-580 mm. 5-Prong nylon base for stability. Twin Wheel heavy Duty Castor for easy mobility under load. Seat Hot pressed ply wood with steel T-Nuts for rigid fastening with PP cover. Back is moulded Bright Bar with stitched Mesh Cloth. Sturdy steel column gas lift for centre support and seat height adjustment. Telescopic ABS cover over steel column. Lockable synchrony tilt mechanism and with Single piece Die castes Fixed PP arm rest . Quality tapestry. High density Moulded PU cushion.

Lab Stool Specification: Size:H:710, Seat:H:550, D:300, Under Structure:-Made up of MS cold rolled close annealed,18G tube. Top made of 18mm thick prelaminated particle board. Side edges covered with teak wood beading duly polished. All steel components are epoxy powder coated followed by seven tanks anti corrosion treatment of surface. The overall appearance of the product shall be as per photograph.

MRL LIFT

Providing and Installing, Testing & Commissioning of 13 & 10 Passenger automatic (machine room less) Lift - 1no., including one year free maintenance which will be start from handing over the lift, all taxes and all complete as per following detail specifications. APPROVED BRAND - SCHINDLER / OTIS/ JOHNSON

Product line item 400- SRC BUILDING

Elevator Function- Person Elevator

Elevator group - G01

Number of lifts - 1

Capacity / No. of Passengers - 884 kg / 13 Passengers

Speed - 1.0 m/s

Number of Stops / Entrances - 4 / 4 (G, 1, 2, 3

Travel height - 11.1 m

Pit depth - 1500 mm

Headroom - 4500 mm

Shaft dimensions W x D - 2000 mm x 2400 mm

Machine room - Machine room less

Car dimensions W x D x H - 1050 mm x 2100 mm x 2139 mm

Clear car height HKC - 2100 mm

Car Door size W x H - 900 mm x 2000 mm

Car Door Type - Door center opening, 2 panels

Shaft Wall - Concrete

Building tolerance - -25 mm / +25 mm

Landing door fire protection classification - EN 81-58 E120 [ Two hours fire rated ]

Counterweight location - On the left side

Car access sides - 1

Main stop - 1

Door drive - Fermator Compact

Drive and control - Full Collective control - Simplex

Controller position - In the right door jamb (LDU)

Controller location - Landing at floor 4 on side 1

Drive Power - 5.7 Kw

Main connection - TN-S (3L+PE+N)

Main power supply - 415 V 50 Hz

Light power supply - 230 V

Number of trips per hour - 120

Installation method - Scaffoldless with hoisting device

Maintenance period - 12 months

Inverter type - VAF0xx REGEN

Machine Type - Permanent Magnet (PM)

Car lighting - LED

Car Front Finish - Stainless Steel AISI441 Hairline Front Cathedral

Fixtures - St.steel AISI304 hairline Standard resolution matrix

Button Description - Mechanical push buttons St.st.AISI304 sandblast Braille Buttons

Landing Operating panel version - Stainless Steel AISI304 Hairline Surface vertical in wall Yes

Car door sill - Aluminium

Landing door sill finish - Aluminium sill

Landing door frame dimensions - 60 mm x 60 mm

Product line item 200- FACULTY QUARTER

Elevator Function- Person Elevator

Elevator group - G01

Number of lifts - 1

Capacity / No. of Passengers - 680 kg / 10 Passengers

Speed - 1.0 m/s

Number of Stops / Entrances - 3 / 3 (G, 1, 2

Pit depth - 1500 mm

Headroom - 4500 mm

Shaft dimensions W x D - 1800 mm x 1700 mm

Machine room - Machine room less

Car dimensions W x D x H - 1200 mm x 1400 mm x 2139 mm

Clear car height HKC - 2100 mm

Car Door size W x H - 800 mm x 2000 mm

Car Door Type - Door center opening, 2 panels

Shaft Wall - Concrete

Building tolerance - -25 mm / +25 mm

Landing door fire protection classification - EN 81-58 E120 [ Two hours fire rated ]

Counterweight location - On the left side

Car access sides - 1

Main stop - 1

Door drive - Fermator Compact

Drive and control - Full Collective control - Simplex

Controller position - In the right door jamb (LDU)

Controller location - Landing at floor 3 on side 1

Drive Power - 4.6 Kw

Main connection - TN-S (3L+PE+N)

Main power supply - 415 V 50 Hz

Light power supply - 230 V

Number of trips per hour - 120

Installation method - Scaffoldless with hoisting device

Maintenance period - 12 months

Inverter type - VAF0xx REGEN

Machine Type - Permanent Magnet (PM)

Car lighting - LED

Car Front Finish - Stainless Steel AISI441 Hairline Front Cathedral

Fixtures - St.steel AISI304 hairline Standard resolution matrix

Button Description - Mechanical push buttons St.st.AISI304 sandblast Braille Buttons

Landing Operating panel version - Stainless Steel AISI304 Hairline Surface vertical in wall Yes

Car door sill - Aluminium

Landing door sill finish - Aluminium sill

Landing door frame dimensions - 60 mm x 60 mm

CCTV SERVEILLANCE SYSTEM

Supply, installation , testing & commissioning of NVR 32 Channel: Connect Up to 32 IP Cameras, Up to 8 Megapixels Resolution, HDMI output with 4k output and VGA output with 2MP Output , Support H.265,H.264, MJPEG, Incoming Bandwidth 256 Mbps, 4 SATA Hard Disks, ANR Technology, 4 SATA interfaces for 4 HDDs and capacity of each HDD upto 6TB, 2 USB at least 1 × USB with 3.0, Serial interface:1 RS-485, 1 RS-232, Alarm I/O 16/4, 2 RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface, Multiple network monitoring: Web viewer, CE, FCC, UL certified APPROVED BRAND - HIKVISION, DS-7732NI-k4/ EQUIVALENT.

Supply, installation , testing & commissioning of 2 Megapixel Fixed Lens Camera IR Dome Type: 1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8mm Fixed lens, 0.028 Lux at F1.2, ICR, ONVIF, support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, IK10, Edge Anlalytics- Line crossing detection, Intrusion detection, Inbuilt Audio Motion detection, Scene change detection, video tampering, UL, CE, FCC certified. APPROVED BRAND - HIKVISION, DS-2CD3121G0-IUF/ EQUIVALENT.

Supply, installation , testing & commissioning of 2 Megapixel Fixed Lens Camera IR Bullet Type: 1/2.8"Progressive Scan CMOS, 1920 × 1080 at 25fps, 2.8 mm Fixed lens, 0.01 Lux at F1.2, 0 Lux with IR, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, inbuilt audio Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Video tampering, UL, CE, FCC certified. APPROVED BRAND - HIKVISION, DS-2CD3021G0-IUF/ EQUIVALENT.

Supply, installation, testing and commissioning of outdoor 2MP, VF LENS , 2.8MM TO 12MM, resolution 1920*1080 fixed lens Color Indoor AV Camera, 1/3" CMOS, H.264/MJPEG High-profile, dual Stream support, True Day & Night (TDN) with , Wide Dynamic Range (WDR), Open Network Video Interface Forum (ONVIF) Profile S & G - TF card support (128 GB), IP66 & IK 10 Rating, Power Over Ethernet (POE), IR distance upto 30 Meter. APPROVED BRAND - HIKVISION, DS-2CD3056G2-IS/ EQUIVALENT.

Supply, installation , testing & commissioning of POE switch of 10/100/1000 Mbps on each Ethernet port. The switch shall be mounted on rack. The rate shall also include cost of power supply and providing end termination.

24 port 10/100/1000 Mbps managed Giga Byte POE Switch APPROVED BRAND - One Touch, OT-1724P/ EQUIVALENT.

16 port 10/100/1000 Mbps managed Giga Byte POE Switch APPROVED BRAND - One Touch, OT-1716P/ EQUIVALENT.

HDMI Splitter” is a unit whereby you can send your HDMI output of set-top boxes, DVD Players, D-VHS Players, PC's and other HDTV devices. APPROVED BRAND - Mile Stone, ML 401 HMVS/ EQUIVALENT.

Supply, drawing and connecting of cat-6, UTP cable with conduit for cctv APPROVED BRAND - D-LINK/ Polycab, NCB-C6UGRYR-100/ EQUIVALENT.

Supply , Fixing of 6U Racks for POE switch installation in floor wise APPROVED BRAND - D-LINK, NWR-6U-5550-GR/ EQUIVALENT.

Supply , Fixing, Commissioining of 50 Inch Monitor for CCTV APPROVED BRAND - LG/ EQUIVALENT.

Supply , Fixing, Commissioining of HDMI cables for connecting monitor to NVR APPROVED BRAND - 4K/ EQUIVALENT.

Supply , Fixing, Commissioining necessary accessories for cctv , nvr and monitors

AUDITORIUM (STAGE CRAFT, STAGE LIGHTING & AUDIO SYSTEM

Supplying, Installation, Testing & Commissioning of Motorized DMX operated Main Curtain 15.5 Mtrs straight, Centre partting as per design. This mechanisam shall be provided with 01 Nos. of 1.5 HP, 1440 RPM, 90 B5 frame, 3Ph. 415VAC Motor with Brake for Motor System to lift a load which should be synchronized with Motor Control centre Panel. Winch shall have 3 phase motor with an RPM of 1440,KW (HP) : 1.1(1.5), Frame : 90S, EFF:75.0%, MTG : B5, AMP :2.7Y, Volt:415v, DE BRG : 62052Z, DUTY:S1, FREQ:50Hz, NDE BRG:62052Z, IP:55, AMB:50 degree.The outer surface temperature is limited.It shall have an Worm Reduction Gearbox with GMRV-90 80:1, 90B5, Single Reduction 7.5:1 to 100:1 and the size shall be 90. It shall have an drive unit base frame to fix the gear box which contains one shaftMade up of I Track for complete lengthCurtain holding trollies with ball bearing for smoother noiseless movement consisting of 4 wheeler master trolley and 2 wheeler trolley placed uniformly at specific interval of 200mm /250 mm throughout the track Overlap of 0.5~0.9 Mtrs. Motor Cable termination box Trollies uniformly distributed along the track at every 200/250mm with a master trolley. Open and close limit controller.Drive unit with suitable capacity of motor unit, Wire Rope shall be of GI Wire ropes Min 3mm Dai Undergone through various chemical treatment to keep them rust free, Black texture finish paint. All metal parts are powder coated

Supplying, Installation, Testing & Commissioning of FRLS Copper unarmoured Flexible cable IS694 having 7 Core each of 1.5 Sq mm size.

Supplying, Installation, Testing & Commissioning of FRLS Copper unarmoured Flexible cable IS694 having 4 Core each of 4 Sq mm size.

Supplying, Installation, Testing & Commissioning of High quality Velvet fabric fire retardant treated as per approved colour and make with a gathering of 100% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing on to curtain trollies (For Main Valance) Size: 14.5 Mtr x 1.2Mtr.

Supplying, Installation, Testing & Commissioning of High quality Velvet fabric fire retardant treated as per approved colour and make with a gathering of 100% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing on to curtain trollies (For Main Curtain) Size: 15.5 Mtr x 5 Mtr.

Supplying, Installation, Testing & Commissioning of On Stage Fixed Valance Bar 14.5 Mtrs Length Straight as per the design made out of 40NB 48 OD Mild steel pipe dual barrel, supported to hang the Main Valance of the stage system duly powder coated with matt black texture finish paint. All the materials under gone through 7 tank process with various chemical treatment to keep them rust free

Supplying, Installation, Testing & Commissioning of 100W High Quality LED Parcan Light complete with, Lamp source 3200K CCT Colour temperatureCRI & TLCI Values above 95COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) DmX 512 dimming with 3 channel controlBeam Angle of 9˚ / 25˚ / 35˚Total Power Consumption of 120W High quality output replacing 1000W Halogen Par Flicker Free 100% for Tv & Film Cameras 11.7KHz Refresh Rate, Linear Dimming 0 ~ 100%Fuse and Internal safety protections Strobe option Adjustable 1~25 times/Sec Variable Fixture provided with Yoke of Manual Adjustment 5 Pin XLR for DmX , Black powder coated body. RDM Control options with latest technology (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 LM79 Certificates from NABL Acrediated laboratory.Brand embosed impact on the light body for genuine product

Supplying, Installation, Testing & Commissioning of 200W LED Profile Spot 19 Degree Light complete with, 3200K CCT Colour Temperature COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) CRI & TLCI above 95, Strobe option Adjustable 1 ~ 25 times / Sec 4 Kinds of dimming curves, Black finish housing, Manual Focus with 4 Beam shaping cutters Efficient and well-designed Lamp reflector Efficient Copper tube based Heat Sink for Heat Dissipation Sleek and Unique Designed Light weight body Fixture provided with Yoke of Manual Adjustment DmX 512 dimming with 1 or 3 Channel modes IP20 protection having Lux @ 3 Mtrs above 9080 suitable to illuminate the key presentor or talent on stage. RDM Control options with latest technology (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 . CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 LM79 Certificates from NABL Acrediated laboratory. Brand embosed impact on the light body for genuine product

Supplying, Installation, Testing & Commissioning of 200W LED Blinder Light 30 Degree complete with 3200K CCT 2x100W Chip On Board LED Lamp source COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided); DmX 512 dimming with 4 /8 Channel modes CRI & TLCI Value > 90 , Strobe option Adjustable 1 ~ 25 times / Sec Variable, Beam Angle 30 Degree; Total Power Consumption of 220W 11.7KHz Refresh Rate, In built preset’s for effects Fuse and Internal safety protections, Active Cooling with Low Noise Fan, 5 Pin XLR for DmX, High quality well designed inbuilt reflector, Flicker Free 100% for Tv & Film Cameras, Black finish housing, IP20 protection, Having Strobe option and smooth dimming,illuminate Stage with uniform light intensity levels. RDM Control options with latest technology (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 LM79 Certificates from NABL Acrediated laboratory.RDM Control options with latest technology (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 . CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 LM79 Certificates from NABL Acrediated laboratory. Brand embosed impact on the light body for genuine product

Supplying, Installation, Testing & Commissioning of 100W LED Fresnel Light having COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) 3200K colour temperature High quality uniquely designed Fresnel Lens CRI,TLCI and R9 value above 96 LED COB Based Source No Multiple Shadows – Single Source illumination Total Power Consumption of 110W Linear dimming 0 ~ 100% Adjustment Flicker Free for High FPS, Power AC90-260V, 50/60HZ Working Temperature - +40° ~ -30° Active Cooling with Low Noise Fan DmX & RDM Control options with latest technology Fixture provided with Yoke of Manual Adjustment Manual and DMX control Option mode through 5pin xlr Black powder coated fabricated housing with normal yoke. RDM Control options with latest technology (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 LM79 Certificates from NABL Acrediated laboratory. Brand embosed impact on the light body for genuine product

Supplying, Installation, Testing & Commissioning of 54 x 3W LED Par Light RGBW, Beam Angle 25° complete with LED source from Lumiled / Seoul / Nichia or reputed make (LM80 to be provided) ; RGBW 3W Lamp source x 54 Pcs DmX 512 dimming with 8 Channel High Bright Red, Green, Blue, White LED’s Source Unlimited Color Mixing through DmX 0 ~ 100% Linear dimming , In built presets for different colors Strobe Mode 20 times/Sec Data DmX through 3 / 5 Pin XLR’s 65dB ~ 130dB Sound sensing capacity Power In and Out Connections High precision colors, IP20 protection Powder coated Black finish housing Having Sound Control & Master Slave Auto Run Mode Illuminate the Indoor stage with unlimited colour effects Rigidly built pressure die-casted Aluminium body. RDM Control options with latest technology (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 LM79 Certificates from NABL Acrediated laboratory. Brand embosed impact on the light body for genuine product

Supplying, Installation, Testing & Commissioning of 54x3W LED 3200K Par Light Beam Angle 25° complete with 3200K 3W Lamp source x 54 Pcs LED source from Lumiled / Seoul / Nichia or reputed make (LM80 to be provided) Having CRI TLCI Values above 95 ; Flicker Free for high FPS Smooth fade in and Fade out; High precision steady color No heat, DmX 512 dimming with 2 Channel 0 ~ 100%, Powder coated Black finish housing Rigidly built pressure die-casted Aluminium body LED Easy view display ; Data DmX through 3 / 5 Pin XLR’s 65dB ~ 130dB Sound sensing capacity Power In and Out Connections Total Power Consumption of 180W Sound Active Mode Control IP20 protection. RDM Control options with latest technology (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 Brand embosed impact on the light body for genuine product

Supplying, Installation, Testing & Commissioning of Light fixture mouting clamp Customized for suspending on fixed bars on stage Made up of Aluminium Die casted MS threaded T bolt with yellow passivation finish Complete with black powder coating matt black finish. Safe working load 150 KG Suitable to Batten of size 30 OD to 60 OD

Supplying, Installation, Testing & Commissioning of Light Fixture dual safety Chain made up of GI wire rope Bundled and twisted together Having load bearing capacity above 200 Kgs Sleve on the rope. Carabiner Clip

Supplying, Installation, Testing & Commissioning of Suspender cum clamps designed made out of MS material 150mm x 150mm x 5mm MS Base plate Threaded rod, Black powder coated finish All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Suitable to hold various type grid & other rigging systems.

Supplying, Installation, Testing & Commissioning of Fixed on stage Lighting bar/winch of 10 Mtr length constructed with an dual contruction light bar with an Mild Steel 40NB 48 OD black matt finish with an supporting flat patti of height 200mm x 50mm x 6mm thickness for the extra support with 2 holes of 10mm diameter to fix the cable tray on the bar.It shall be hanged from the roof to accommodate various type of stage light fittings. It should hang from the roof with MS anglewhich is suspended from the fish plate of 5mm thickness which is fixed on the rcc roof with 4 anchor fastners of 10mm which can take an total load of 400KG each fastner. Made out of 48mm Outer Dai, 40 Nominal Bore Material for the light bar shall be of Mild Steel Pipe. Dual Barrel Arrangement Powder coated with Matt black Texture Fixing Through Suspenders as per site conditions Dual Construction and an additional End Caps on the Pipe end shall be there Light bar Length shall be of customized type as per site condition. Upper pipe of dual construction is used to anchor the bar lower pipe is effectively used to hang the light fixtures

Supplying, Installation, Testing & Commissioning of Fixed FOH Lighting bar/winch of 12 Mtr length constructed with an dual contruction light bar with an Mild Steel 40NB 48 OD black matt finish with an supporting flat patti of height 200mm x 50mm x 6mm thickness for the extra support with 2 holes of 10mm diameter to fix the cable tray on the bar.It shall be hanged from the roof to accommodate various type of stage light fittings. It should hang from the roof with MS anglewhich is suspended from the fish plate of 5mm thickness which is fixed on the rcc roof with 4 anchor fastners of 10mm which can take an total load of 400KG each fastner. Made out of 48mm Outer Dai, 40 Nominal Bore Material for the light bar shall be of Mild Steel Pipe. Dual Barrel Arrangement Powder coated with Matt black Texture Fixing Through Suspenders as per site conditions Dual Construction and an additional End Caps on the Pipe end shall be there Light bar Length shall be of customized type as per site condition. Upper pipe of dual construction is used to anchor the bar lower pipe is effectively used to hang the light fixtures

Supplying, Installation, Testing & Commissioning of Power Distribution Electrical panel having a Incomer of 63A. Floor mount / rack mount / wall mount. Miniature circuit brakers of single poles shall be fixed of different ratings from 6/10/16/25A as per the lighting fixtures.Wiring inside the module for power, control protection and instrument etc. shall be done with use of 1100 V confirming to IS 694 and IS 8130 All welding slag grounded off and welding pits wiped smooth with plumber metal.Power panels shall be designed in such a way that the internal space is sufficient for hot air movement, and the electrical component does not attain temperature more than 40 degree Celsius.Fabricated panel shall be supported with ms angles of size 25mm x 25mm with an 1.8mm thickness sheet to hold the structure. Nuetral separation made using incomer of L&T or Schneider make, Voltmeter, Ammeter display for reading visualization Individual MCB control for 20 outgoing circuits RYB Phase indicators internally wired using IS certified wires and cables Terminal for both incoming and outgoing cable shall be suitable for 1100 volts grade, aluminum/copper conductor PVC insulated and sheathed, armoured cable and shall be suitable for connections. Provided with ivery connectors for the internal terminations and external outgoing connecting points Custom built as per specification and project requirement.

Supplying, Installation, Testing & Commissioning of High quality power junction box 4 way made up of MS Sheet metal fabricated housing. Snap fit fixing /15 (1.5mm ) Total Max Rating 10A, 250V A.C 20˚C to +70˚C Operating Temp Moldings: Nylon, Flammability Rating UL94V-0 Black powder coated, fibre glands of suitable size fitted with Powercon or IEC connector Box 10A. Clamp arrangement for fixing or Raul plug arrangement for wall / floor fixing

Supplying, Installation, Testing & Commissioning of High quality power junction box 2 way made up of MS Sheet metal fabricated housing. Snap fit fixing /15 (1.5mm ), Total Max Rating 10A, 250V A.C 20˚C to +70˚C Operating Temp Moldings: Nylon, Flammability Rating UL94V-0 Black powder coated, fibre glands of suitable size fitted with Powercon or IEC connector Box 10A. Clamp arrangement for fixing or Raul plug arrangement for wall/floor fixing

Supplying, Installation, Testing & Commissioning of High quality Dimming In junction box 1 way made up of MS Sheet metal fabricated housing ; High temperature resistant insulator material All metal housing offers best overall RF protection & electromagnetic shielding Black powder coated, fibre glands of suitable size fitted with 5 Pin DmX XLR Male socket Clamp arrangement for fixing or Raul plug arrangement for wall /floor fixing

Supplying, Installation, Testing & Commissioning of High quality Dimming Out junction box 1 way made up of MS Sheet metal fabricated housing High temperature resistant insulator material All metal housing offers best overall RF protection & electromagnetic shielding Black powder coated, fibre glands of suitable size fitted with 5 Pin DmX XLR Female socket Clamp arrangement for fixing or Raul plug arrangement for wall /floor fixing

Supplying, Installation, Testing & Commissioning of DmX Loop Junction Box having 1 No. of DmX 5 Pin XLR Female Socket & 1 No. DmX XLR Male Socket fitted on to a sheet metal fabricated compact Junction box powder coated with matt black texture finish paint. High temperature resistant insulator material All metal housing offers best overall RF protection & electromagnetic shielding. Clamp arrangement for fixing or Raul plug arrangement for wall /floor fixing

Supplying, Installation, Testing & Commissioning of Internal Earthing System with copper bare conductors all along the cable trays, metal parts and Installation Hardwares

Supplying, Installation, Testing & Commissioning of Black Powder coated cable trays made out of MS Sheet fabricated for a size of 40 x 150 x 40mm & 1.6 mm thickness undergone through 7 tank process with various chemical treatment to keep them rust free with perforation for heat dessipation provided with lid.

Supplying, Installation, Testing & Commissioning of Black Powder coated cable trays made out of MS Sheet fabricated for a size of 40 x 75 x 40mm & 1.6 mm thickness undergone through 7 tank process with various chemical treatment to keep them rust free with perforation for heat dessipation provided with lid.

Supplying, Installation, Testing & Commissioning of DmX Male Female Connectors 5 Pin having rubber sheeth protection for Cross connecting DmX wiring connections

Supplying, Installation, Testing & Commissioning of DmX Male Termination Connector 5 Pin soldered with required capacity of resistor for signal deframing

DmX Touch Screen based controller having 7” Multi touch screen option 2 DmX Outlets 5 Pin XLR’s, 512 Channels each, Optically isolated outputs, 4 Smooth Encoders for control operation of attributes, Backlit keys, 12 Fader Stacks, 600+ Playbacks, 350+ Group saving, 350+ Presets, User defined shape effects, Macro saving options, External Midi timecode options, Internal clock, Shortcut user interfaces, Master fader, Blackout Key under Master fader, Numerical keypad for the light command entry inbuilt embedded within controller, USB interface, Scene saving options, Show saves and load save features, custom built user interface library for fixture files.

Supplying, Installation, Testing & Commissioning of FRLS Copper unarmoured Flexible cable IS694 having 3 Core each of 1.5 Sq mm size.

Supplying, Installation, Testing & Commissioning of 5 Core DmX Cable with Sheathed housing on the cable, well designed insulation, low noise suitable to transmet DmX signal.

Supplying, Installation, Testing & Commissioning of Suspender cum clamps designed made out of MS material 150mm x 150mm x 5mm MS Base plate Threaded rod, Black powder coated finish . All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Suitable to hold various type grid & other rigging systems.

Supplying, Installation, Testing & Commissioning of C Profile MS Hot rolled strips 3mm thick with Extra U bend used either to create basic supports Customized 40 x 50mmm, All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Makes easier to suspend all the stage machinery Duly powder coated Matt black texture finish paint

Supplying, Installation, Testing & Commissioning of Cable Connecting Circuit Boxes for the termination of cables from Electrical panel to the grid level point made out of MS Sheet metal fabricated housing duly powder coated with matt black texture finish paint, fitted with required channels and ivery connectors, necessary glands etc.

Both side Prusenium in front of the Stage of 250 Sq. Ft on both side of the stage, made up of Irona angle structure, surface covered with ply wood vinyl board and iron structure for holding the Sub-Woofer speakers from the Ground. –

Side wings – Heavy duty Side wings made up of Iron angles, covered with ply vinyl Borads on both the sides, rotable, size 48” (1219mm) Breadth x 199” (5060mm) Height – 3 nos in each side

Control Room of size 6.5 ft (Height) x 6 ft (B) x 10 ft (L), structure Made up of Alumunium channel, covered by ACP Board from All side, Front side layer of 4 ft ACP Sheet, 2 ft Glass and ½ again ACP Sheet, Top covered with Alumunium Net, having Ply board Shelves for storing and operating the Light and sound system etc, With adequate AC Line connection inputs for all the Audio and sound equipments etc.

Wooden Podium, height 114 cm height; 60cm x 36cm Platform and 54cm x 38cm Wooden base, made up of ply wood vinyl board, covered with acrylic sheet.

Supplying, Installation, Testing & Commissioning of self standing Back Wall structure Made up of Alumunium / wodden structure, infilled by soft pinnable Board from All side, Covered by best quality texctured cloth of white colour to be used for Pinning of any Display materials and for Projection also Size 48 ft (L) And 14 ft (H).

FOH Passive Loudspeaker, Model QM700 Power Handling: 700W program ; 1400W peak Frequency Response: 50-16kHz Sensitivity: 98dB @ 1kHz Maximum SPL @ 1m: 130dB Impedance: 8 ohms Connections and Wiring: 2 x Speakon NL4 - 1+/1- (2+/2- through) Woofer: 15" High Power Woofer Tweeter: 1.4" Ferrite Compression Driver Directivity: Asymmetric +15/-45 ; 45/90 horizontal Dimensions: 725 x 432 x 369.5 mm Weight – 28 kg net Preferred Brand – QUEST / MAYERSOUND / AUDIOFOCUS / BOSE

Active (Powered) 18” subwoofer, Freq. Range (-10dB): 36Hz~140Hz Max Calculated SPL: 133dB Frequency Response (-3dB) 52.5Hz - 92.5Hz Amplifier Power: 1000W LF Transducer: 18" / 450mm Crossover Frequency: 110Hz Preset and Optimised Input Connector: Female XLR Output Connector: Male XLR AC Input: AC220~240V 50Hz/60Hz Net Weight: 38.5kg Shipping Weight: 43kg Dimensions (WxHxD): 700mm x 530mm x 700mm Carton Size (WxHxD): 790mm x 620mm x 800mm Preferred Brand – QUEST / MAYERSOUND / AUDIOFOCUS / BOSE

Active (Powered) Loudspeaker for Stage Monitor, Max SPL *calculated 125 dBSPL Sensitivity *5-band average 98 dBSPL Frequency Response 60Hz – 20kHz Amplifier Power RMS: 380W Peak: 470W Transducers HF: 34mm Compression Driver LF: 12” High Power Woofer Directivity *H x V 85° x 75° Connections XLR+¼” In, XLR Out Dimensions *H x W x D 620 x 380 x 347mm Net Weight 16.5kg Preferred Brand – QUEST / MAYERSOUND / AUDIOFOCUS / BOSE

Passive side running loudspeakers Rec Amplifier 320 - 500W Nom . Impedance 8 ohm Frequency Response 75Hz - 19kHz Max SPL 119dB Directivity Asymmetric +15/-45 Vertical, 30/45 Horizontal Woofer 8” High Powered Woofer Tweeter 1” Ferrite Compression Driver Connections & Wiring 2x Speakon 1+/- Dimensions 449 x 250 x 250mm Weight 8.9kg net Preferred Brand – QUEST / MAYERSOUND / AUDIOFOCUS / BOSE

Passive Speakers for BALCONY Area, Rec Amplifier 240 - 360W Nom . Impedance 16 ohm Frequency Response 75Hz - 19kHz Max SPL 117dB Directivity 100° x 60° [hor x ver] Woofer 5” Woofer Tweeter 1” Ferrite Compression Driver Connections & Wiring 2x Speakon 1+/- Dimensions 248 x 182 x 150mm Weight 6.2kg net Preferred Brand – QUEST / MAYERSOUND / AUDIOFOCUS / BOSE

Consealable sobwoofer for Balcony Area, Max SPL *calculated ; 118dBSPL Sensitivity 1W @ 1m - 60Hz : 96dB Frequency Response : -9dB 44Hz – 90Hz Impedence ; 8 ohms Power Handling : 300W RMS - 10" 50mm Voice Coil Dual Spider, Dual Magnet WooferDriver Connectivity ; Captive Screw Terminal Plug (In/Thru) Dimensions *L x W x H : 500 x 470 x 256mm Net weight – 15.1 Kg. Preferred Brand – QUEST / MAYERSOUND / AUDIOFOCUS / BOSE

Adaptor Plate for SPEAKERS.

4 channel Power Amplifier , 1500 Watt per channel Frequency Response 20-20kHz (+/-0.3dB) Peak Output Current 40A Dynamic Range 111dB (A-weighted) Noise Level -67dBu (A-weighted) Distortion (1kHz@1W/8Ohm) 0.004% Distortion (1kHz@50W/8Ohm) 0.003% Crosstalk (1kHz@1W/8Ohm) -90dB Gain 32dB Maximum Input Level +24dBu Input Type XLR Balanced Inputs and Euroblock Links (+ optional Expansion Module) Input Sensitivity +4dBu Input Impedance 10kOhm Output Resistance 13mOhm Front Controls Volume Adjust, 80Hz HPF Enable, 100Hz LPF Enable, Limiter Enable, Auto-Standby enable 1. Rate power : @8Ohm 4x 1500W as per speaker power rating. 2. Rate power: @4Ohm 4x 1400W as per speaker powr rating. 3. Standby, while mute option enables the amplifier to be activated within 1ms. 4. Voltage power rating available 70V (22Ohm) 4x 1500W 100V (33Ohm) 4x 1500W. 5. Connector Input Type XLR Balanced Inputs and Euroblock. MODEL SIZE PER CHANNEL BRIDGED-MONO MODE Maximum Dynamic Power (@1KHz, 1% THD) 8Ohm 4Ohm 70V (22Ohm) 100V (33Ohm) 8Ohm 4Ohm 70v 100V QX41500 2RU 4x 1500W 4x 1400W 4x 1500W 4x 1500W Preferred Brand – QUEST / MAYERSOUND / AUDIOFOCUS / BOSE

Digital Mixing Console (Mixer) 19” Rack Mountable 16 Mono Mic/Line Inputs (TRS + XLR) Recallable AnaLOGIQTM Preamps 3 Stereo Inputs (TRS) 12 Mix Outputs (XLR) 7 Monitor Mixes (4 mono + 3 stereo); 4 FX Engines 2 dedicated FX Sends / Returns; 4 Mute Groups 4 DCA Groups; AES Digital Out 24×22 USB Audio Interface dS NAKETM Remote Audio Port 17 Motor Faders 800×480 Touchscreen 4 Soft Keys Preferred Brand – ALLEN & HEATH / MAYERSOUND / AUDIOFOCUS / BOSE

Combo Wireless UHF Microphone system, (consisting 2 nos. Hand Held wireless microphones working on a single receiver) • Available Frequencies: between 794 –806 MHz • Operating Range: LO power mode: 18 m (60 ft.)* HI power mode: 75 m (250 ft.)* * under typical conditions • Audio Frequency Response: 50 Hz – 15 kHz • Transmitter RF Output Power: LO power mode: 1 mW maximum HI power mode: 10 mW maximum • Audio Output Connector: XLR balanced and ¼" unbalanced • Maximum Output Level: -19 dBV (XLR), -5 dBV (1/4”) (R25 - Band for Thailand Regulation) (ref. +/-33kHz deviation with 1 kHz tone) • Battery Life: Up to 10 hours with 2 AA batteries • Dynamic Range: >90dB, A-weighted • System Distortion: Preferred Brand – SHURE / MAYERSOUND / BOSCH / BOSE

Cardiode Wired Vocal Microphone, Total Harmonic Distortion Less than 0.25% (130 dB SPL at 250 Hz into 800-ohm load) Maximum SPL 142 dB with 800-ohm load 134 dB with 150-ohm load Hum Pickup -7.5 dB equivalent SPL in a 1 millioersted field (60 Hz) Output Noise (equivalent sound pressure levels; measured with true rms voltmeter) 29 dB typical, A-weighted 32 dB typical, weighted per DIN 45 405 Dynamic Range 113 dB (maximum SPL to A-weighted noise level) Signal-to-Noise Ratio 65 dB (IEC 179)* at 94 dB SPL Overvoltage and Reverse Polarity Protection Max.External Voltage Applied to Pin 2 and 3 with Respect to Pin 1 + 52 Vdc Reverse Polarity Protection,200 mA max. (diode-clamped) Phasing Positive pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 Cartridge Capacitance 27 pF Power Supply Voltage .ll to 52 Vdc, positive pins 2 and 3 Current Drain .1.0 mA to 1.2 mA Environmental Conditions Relative Humidity 0-50°/o -2g0 to 74OC (-20' to 165OF) Relative Humidity 0-95% -2g0 to 57OC (-20' to 135OF) Connector Three-pin professional audio** Case Aluminum construction with black finish and black steel grille. Preferred Brand – SHURE / MAYERSOUND / BOSCH / BOSE

Cardiode Wired Instrument Microphone, Type Dynamic Frequency Response 40 to 15,000 Hz Polar Pattern Cardioid Sensitivity (at 1,000 Hz Open Circuit Voltage) Open Circuit Voltage: -56.0 dBV/Pa (1.6 mV) (1 Pa = 94 dB SPL) Impedance Rated impedance is 150Ω (310Ω actual) for connection to microphone inputs rated low impedance. Polarity Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3. Case Dark gray, enamel-painted, die-cast steel with a polycarbonate grille and a stainless steel screen. Connector Three-pin professional audio connector (male XLR type) Net Weight 284 grams (10 oz) Dimensions 157 mm (6-3/16 in.) L x 32 mm (1-1/4 in.) W at the widest point Preferred Brand – SHURE / MAYERSOUND / BOSCH / BOSE

Dual-Section 12” Gooseneck Microphone, with Base and PS Cartridge Type Electret Condenser Frequency Response 70–16000 Hz Polar Pattern Cardioid Output Impedance 180 Ω Sensitivity (at 1 kHz , open circuit voltage) –33 dBV/Pa[1] (22 mV) Maximum SPL (1 kHz at 1% THD) 120 dB SPL Signal to Noise Ratio (referenced at 94 dB SPL) 67 dB Dynamic Range 93 dB Self Noise (equivalent SPL, A-weighted, typical) 27 dB SPL Common Mode Rejection (10 Hz to 100 kHz) >45 dB Preamplifier Output Clipping Level (1% THD) −7 dBV Polarity Positive pressure on diaphragm produces positive voltage on pin 2 with respect to pin 3 Power Requirements 11–52 V DC[4], 2.0 mA Environmental Requirements Operating Temperature Range: -18° C to 57° C (0° F to 135° F) Relative Humidity: 0 to 95% Preferred Brand – SHURE / MAYERSOUND / BOSCH / BOSE

Speaker cabels, Connecting cable, Sockets, jacks, Interconnecting cables, Power Points, Jacks, Sockets, Speakons, Microphone cable etc.- BRANDED

Installation, Commissioning and Programming charges for all the system, Mentioned above with fitting charges, labour charges etc.

WUXGA Blue Core Laser Projector, 5000 Lumens Brightness, WXGA Resolutions, Native Aspect Ratio 16:10 Contrast Ratio (FOFO) 3000000:1 Display Color 30 Bits (1,07 billion colors) Light Source Laser, Light Source Life 20000 hrs, Brightness (ANSI lumens) 5000, Throw Ratio 1.36 ~ 2.18 Zoom Ratio 1.6x Lens F/# = 1.81 ~ 2.1,f = 14.3 ~ 22.9 mm Projection Offset (Full-Height) 0% Keystone Adjustment 2D, Vertical ± 30 degrees; Horizontal ± 30 degrees Lens Shift Vertical ± 60% Lens Shift Horizontal ± 23%

Heavy Duty Ceiling Mounting Bracket, 4 to 6 ft Drop adjustable with Necessary cables for projectors (Mains, HDMI).

Supplying, Installation, Testing & Commissioning of Necessary cables, Infrastructures, Labour, Commissioning and installation charges.

Proving and finishing wall with art work or Painting with weatherproof plastic emulsion pants for Sohrai, Kohbar, Saura, Paithkar, Jadupetiya, Kalighat and Madhubani artwork, Etc. as per deign and required including all labours and materials complete job.

Providng, Designing and fixing of Glass Mosaic of 20MMX20MM Size Required Colour and Shapes for making of mural as per Concept Drawing and Approved

Providing and fixing 15" HT. Stainless Steel Lettering Over Building For Building & College Name including logo with all framework, etc. complete job as per approved text.

Supplying, Installing, Testing and Commissioning of split Heat Pump with enamel coated floor mounted Storage tank of required capacity with COP more than 4, water discharge @ 250 liter per hour up to 40 degree Celsius, minimum 3 kw heating element, 50mm thick puff insulated, Auto defrosting mode, 50mm thick puff insulated, working ambient temperature 7 degree Celsius – 43 degree Celsius including all fittings, fixtures and all complete job. Approved Brand – Jaquar Integra Prime/ Equivalent. A) 500 Liter – 3 NOS. B) 400 liter – 1 No.

VRF AC FOR SRC BUILDING

Supply Installation, Testing & Commissioning of modular type Variable Variable Refrigerant Volume air cooled Outdoor units with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 49°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. MS/GI powder coated stand with vibration isolation pads. The unit should have refrigerant-cooled PCB for better life of system.Compressor motor should have more than 4 poles.The ODU shall have low noise condenser fans with external static pressure of the outdoor unit shall be more then 75 Pa to avoid hot air recirculation, auto address setting, auto check function for connection error and complete with indoor and outdoor units with individual controller and with fittings etc. ODU having 100% inverter OEM make advanced hermetically sealed type compressor. Approved Make - Samsung/ Equivalent.

Out Door Unit- Top Discharge

66HP -System 01 (34HP+32HP) (HEAT PUMP)

Model 34, cooling 1 (95.2kw),cooling 324632.0btu/h),cooling 1 (31.73kw), cooling 1(49.9a) Heating 1 95.2kw ERR(nominal cooling 3.00),External Static pressure (80pa), liquid pipe (19.5mm), gas pipe (34.92mm), installtion max lanth (mm 220,110) transmission cable (0.75mm) Refrigerant type (R410A), Factory charing (12.5kg),Sound pressure (db(a)2) 66) net dimensions (WxHxD)(mm1,860*1,695*765) cooling(*C-5-53)

Model 32HP, cooling 1 (89.6kw),cooling 305536.0btu/h),cooling1 (27.57kw), cooling 1(43.4a) ERR(nominal cooling 3.25),External Static pressure (80pa), liquid pipe (19.5mm), gas pipe (34.92mm), installtion max lanth (mm 220,110) transmission cable (0.75mm) Refrigerant type (R410A), Factory charing (12.5kg),Sound pressure (db(a)2) 65) net dimensions (WxHxD)(mm1,860*1,695*765) cooling(*C-5-53)

88HP-System-02 (32HP+28HP+28HP) (HEAT PUMP)

Model 32HP, cooling 1 (89.6kw),cooling 305536.0btu/h),cooling1 (27.57kw), cooling 1(43.4a) ERR(nominal cooling 3.25),External Static pressure (80pa), liquid pipe (19.5mm), gas pipe (34.92mm), installtion max lanth (mm 220,110) transmission cable (0.75mm) Refrigerant type (R410A), Factory charing (12.5kg),Sound pressure (db(a)2) 65) net dimensions (WxHxD)(mm1,860*1,695*765) cooling(*C-5-53)

Model 28HP , cooling 1 (78.6kw),cooling 268026.0btu/h),cooling1 (23.93kw), cooling 1(38a) ERR(nominal cooling 3.28),External Static pressure (80pa), liquid pipe (19.5mm), gas pipe (34.92mm), installtion max lanth (mm 220,110) transmission cable (0.75mm) Refrigerant type (R410A), Factory charing (11kg),Sound pressure (db(a)2) 65) net dimensions (WxHxD)(mm1,295*1,695*765) cooling(*C-5-53)

VRF Indoor Unit

VRF 4-WAY CASSETTE unit with codred remotes & refnets

model 4-way cassete 4.8 tr, cooling (17.0kw), cooling (58120btu/h), heating(19.0kw),heating(64957btu/h),cooling1(98.0kw),heating2(98.0kw),cooling1 (0.83amp), heating2(0.83amp),air flow rate (high/mid/low/)(cfm1200/1024/918),liquid pipe (9.52mm), gas pipe(19.5mm),drainpipe(vp25(od32,id25), power source wire (1.5-2.5),transmission cable (075-1.5), refrigerant (R410A),control methed (eev included), sound pressure (high/mid/low)(db(a)45/43/40),net dimensions(wxhxd)(mm840*372*840), net dimensions (wxhxd)(mm 950*64*950),drain pipe (Built-in), Air filter (Aviailable)

Model 4-way Cassete 4.0 TR, cooling (14.0kw), cooling (47800.0btu/h), heating(16.0kw),heating(54600.0btu/h),cooling1(89.0kw),heating2(89.0kw),cooling1 (0.62amp), heating2(0.62amp),air flow rate (high/mid/low/)(cfm1059/988/918),liquid pipe (9.52mm), gas pipe(19.88mm),drainpipe(vp25(od32,id25), power source wire (1.5-2.5),transmission cable (075-1.5), refrigerant (R410A),control methed (eev included), sound pressure (high/mid/low)(db(a)45/43/40),net dimensions(wxhxd)(mm840*372*840), net dimensions (wxhxd)(mm 950*64*950),drain pipe (Built-in), Air filter (Aviailable)

Y-Joint

Cordless Remote

VRF Outdoor Installation with Proper Vibration isolation , testing & commissioning of the system (except lifting-sifting)

VRF Copper piping

Suction Line wiith closed cell nitrile rubber & necessary support

Liquid Line wiith closed cell nitrile rubber & necessary support

Refnet joint installation

SITC of 2C X 0.75 Sqmm Copper shilded communication cable

SITC Of PVC Drain Piping with support

25mm Dia

40mm dia

SITC Of GI Ducting with required support

9mm thick closed cell nitrile rubber thermal insulation with required adhesive

Duct Accoustic insulation with open cell nitrile rubber

SITC of Supply & Return air Grill/Diffusers with VCD

Canvas Connection

Extra Refrigerant charging with proper vaccumising

VRF AC FOR (AUDITORIUM)

Supply of Air-conditioning units

Supply of Top discharge type AI based Modular Variable refrigerant flow (VRF) system with Multiple Smart DC scroll type compressors (Advanced Flash Injection Compressor), Air cooled condenser with low noise Multi serration Fan, Dual Heatsink, having interconnected control wiring and refrigerant housed in compact housing duly powder coated of following capacities and matching air cooled condenser with copper tubes. Condenser shall be comprised with an anti-corrosive layer of epoxy acrylic and a hydrophilic layer of acrylic resin that disperses water and reinforces its corrosion-resistance. The units must have high COP/EER at AHRI condition as per following requirement. Bidder to submit the COP/EER declaration on OEM letterhead, duly sealed and signed. Approved Brand - Samsung/ Equivalent)

Air conditioning system with Heat Pump facility suitable for 415 +/- 10% Volt, 50Hz Outdoor Units complete with Individual controllers, accessories, including full charge of refrigerant.

Outdoor Units

26.0 HP (Heat Pump) having COP/EER not less than 4.55 / 3.81

Model 26 HP, cooling 1 (72.8.2kw),cooling 248248.0btu/h),Heating 1 kw 78.4 Heating 1 btu/h) 267344.0 cooling1 (18.86kw),Heating 1 kw 17.19 cooling 30a) heating 1 27 ERR(nominal cooling 3.00),External Static pressure (80pa), liquid pipe (19.5mm), gas pipe (34.92mm), installtion max lanth (mm 220,110) transmission cable (0.75mm) Refrigerant type (R410A), Factory charing (12.5kg),Sound pressure (db(a)2) 65) net dimensions (WxHxD)(mm1,860*1,695*765) cooling(*C-5-53)

20.0 HP (Heat Pump) having COP/EER not less than 4.61 / 4.55

Modal 20 HP, cooling 1 67.2 ),cooling 229152.02.20btu/h),cooling 1 (75.6kw), Heating 1 257796.0 cooling 1(16.8)Heating 1 16.61 ERR(nominal cooling 4.00),External Static pressure (80pa), liquid pipe (15.88.5mm), gas pipe (34.92mm), installtion max lanth (mm 220,110) transmission cable (0.75mm) Refrigerant type (R410A), Factory charing (12.5kg),Sound pressure (db(a)2) 65) net dimensions (WxHxD)(mm1,860*1,695*765) cooling(*C-5-53)

AHU KIT with Controller and Wired Remote Controller

Outer Skin 0.6 mm Pre-Costed GI,Inner Skin 0.6 mm Plain GI,Frame work Extruded Aluminum

Profile with thermal break & internal Covering, Thickkness of Insulated Panels

43 mm thcik PUF Insulated having density 38+2 kg/m3, Drain Pan Single skin SS 304 with

19 mm thikc nitrile Insulation, Base frame C section of 75 x 40 mm GI

64.0 TR AHU Kit with Wired Remote and controller

16.0 TR AHU Kit with Wired Remote and controller

Supply of Floor/ Ceiling mounted Double Skin AHU with 6-RD DX-Cooling coil, Backward curved fan with Motor, thermal Break profile, and Mixing box chamber. AHU shall be comprised with Pre filter. Total Static pressure shall be as follows. Approved Brand - Samsung/ Equivalent)

13000 CFM / 64 TR / 6-RD/ Floor Mounted / Static Pressure of 80 mm WC

4000 CFM / 16 TR / 6-RD/ Ceiling Suspended / Static Pressure of 45 mm WC

Supply of Y joints for Indoor / outdoor Unit Distribution

Supply of touch Screen Controller with 7" LCD Display for controlling the system. The controller shall be connactable up-to 128 indoor units having following options: a. Centralized Control, interface Control, b. Central management of AHU, c. Schedule function (Weekly/Daily), d. USB keyboard suppport, e. Error display, f. Temperature setting limit, g. Zone Control, h. Child Lock setting, i. operation Mode Lock, j. External Contact control etc.

Lowside: Installation, testing and comissioning of the VRF system

Installation testing and comissioning of VRF outdoor including Lifting, shifting

Installtion testing and comissioning Indoor Units with Controller

DX AHU

Touch screen based Central controller

Supply and charging of refrigerant (R410a) including Nitrogen Pressure testing and vaccumising.

Supply and laying of interconnecting Hard drawn Copper piping between Indoor to Outdoor units including Nitrille rubber insulation of 13 mm / 19 mm thickness. The piping shall be supported properly with necessery supporting arrangement as required.

53.98 mm dia copper piping with 19mm thick nitrille rubber

44.45 mm dia copper piping with 19mm thick nitrille rubber

41.28 mm dia copper piping with 19mm thick nitrille rubber

38.1 mm dia copper piping with 19mm thick nitrille rubber

34.93mm dia copper piping with 19mm thick nitrille rubber

31.8mm dia copper piping with 19mm thick nitrille rubber

28.58mm dia copper piping with 19mm thick nitrille rubber

25.4mm dia copper piping with 19mm thick nitrille rubber

22.22mm dia copper piping with 19mm thick nitrille rubber

19.05mm dia copper piping with 19mm thick nitrille rubber

15.88mm dia copper piping with 19mm thick nitrille rubber

12.7mm dia copper piping with 19mm thick nitrille rubber

9.53mm dia copper piping with 19mm thick nitrille rubber

PVC drain piping with 9 mm thick nitrill rubber insulation

Supply and fixing of site fabricated GI ducting as IS-656

Supply and Fixing of Grill/ Diffuser

Supply and fixing of Grill/Diffuser with VCD

Supply and fixing of Grill/Diffuser without VCD

Supply and fixing of Motorized fire damper with actuator and control panel

Actuator and Control Panel

Interconnecting control cum transmission wiring between indoor and Outdoor unit with flexible GI Conduit. The quantity shall include the transmission cabling upto Central controller

Supply and fixing of Outdoor stand including vibration isolator

Supply and fixing of Canvas connection

Thermal insulation with 19mm close cell nitrille rubber/XLPE with recommended Adhesive

Acoustic insulation with 10mm thick open cell nitrille rubber/XLPE with recommended adhesive

ELECTRICAL WORK

Main MCC Panel

Supply, installation, testing and commissioning of Cubical type sectinalised floor standing switch board by CPRI apprved firms of 31 MVA fault capacity at 415 V complete with 4 strip, 800 A capacity Aluminium Bus - Bar Electrolytic grade E-91, cable alley, switchgears suitable for AC-23 duty & of following capacity & as per specification given in the tender.

a) Incomer

Outgoings

a) VRF ODU, 19 Kw Each (9W+0S)

b) 2 Nos Feeder for Spare Each Type

c) 5 Nos Feeder for AHU (5 Nos AHU)

Electrical Power Distribution Box

Supply, installation, testing and commissioning of 415V, 3 Ph, 50 Hz, Wall Mounted Isolators with Box up-to 80 Amps.

Starter (DOL / Star Delta) cum Control panel for AHU Units

Power & Control Cabling

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium / Copper conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification.

4C x 16 Sq. mm Cu

4C x 10 Sq. mm Cu

3C X 10 Sq. mm Al

3C X 6 Sq. mm Al

Earthing Strip / Wires as per specs.

Supply & laying of 25 x 6 mm GI strip recess / surface as strip earth lead including soldering etc. as required.

Supply & laying of 8 SWG GI wire.

Cable Tray for Electrical cabling and Piping

Fabricating and installing following size of perforated M.S. Cable trays including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M.S. suspenders and including painting with powder coating etc as required.

200 mm wide x 50 mm x 1.6 mm

150 mm wide x 50 mm x 1.6 mm

Low-Side Installation Cost Inclusive of Material & labour : Copper Refrigerant piping Works with nitrile rubber insulations and supports, Drain piping works for IDU, Control cabling works with PVC conduits, GSS Ducting Woeks, complete with Canvass connections, thermal & acoustic insulations, Grilles/Diffusers etc., Lifting shifting and installation of IDU/AHU & ODU, Testing & commisioning of entire DVM VRF system including additional refrigerant charge as per requirement.

Add GST 18 %

Add Labour cess 1%

R.S.AGRAWAL INFRATECH PVT. LTD. (BID ID -640315)