ADDN/ALTN TO ROOF TREATMENT, GRIT PLASTERING WORK AND MISCC CONNECTED WORKS OF BLDG NO P-167 AND PAITENTS WAITING AREA OF ECHS POLYCLINIC (BHDC) AND 01 NO MINOR WORK OF HARDSTANDING AT P-17 BAIRD PLACE AOR OF AGE B/R-II UNDER GE (EAST) DELHI CANTT-10

Amount

M&L complete removal of existing water proofing treatment of roof including demolition of Mud phuska in roofs, any thickness, including plastering and leeping and removal to outside MD land complete all as specified and as directed.

M&L for plain cement concrete 1:2:4, type B-0, using 12.5 mm graded stone aggregate, as in roof padding, Gola, etc complete all as specified and as directed.

M&L for 15 mm thick Screed/rendering on concrete surface of roof with cement mortar 1:4, finished even and fair including mixing of water proofing compound as per manufacturers instruction complete all as specified and as directed. (Note : Water proofing compound shall be measured and paid separately under respective item of this Schedule).

Supply only integral water proofing compound complete all as specified & as directed.

M&L cleaning surface with wire brush and applying evenly a coat of bituminous primer conforming to IS- 3384 @ 0.30Ltr/Sqm. Over the primed surface, apply a coat of hot blown 85/25 penetration grade bitumen conforming to IS- 702 @ 1.2 Kg/Sqm of the surface area. Applying APP based polymeric membrane minimum weight 3.50kg/Sqm and of minimum thickness 3mm, reiforced with polyster non woven fabric ( weight not less than 150gm/Sqm ). APP membrane will be laid by torching overlaps with a propane or butane gastorch and laid across the slope from lowest line of roof towards ridge with over laps of 75mm in length side and 100mm on the width side of membrane bonded with hot blown bitumen. (Note : (1) The work shall be executed through authorised applicator of manufacturer only. (2) Authrised Applicator shall be approved by GE before starting of work. (3) Guarantee: The contractor shall furnish a written guarantee for the effectiveness of the water proofing treatment for a period of Ten years in favour of the GE. A sum equivalent to 2.5% (Two point Five Percent) of the cost of water proofing treatment shall be retained by the Govt from the contractor’s dues as security deposit. The contractor may, however, furnish a fixed deposit receipt in lieu from a Schedule bank pledged in favour of Garrison Engineer.

Demolition of brick work built in cement mortar complete all as specified and directed

M & L for brick work with sub-class B brick straight or curved on plan built in cement mortar 1 : 6 complete all as specified and directed

Taking down cement plaster of any description on brick or stone walls etc including raking out joints hacking for key scrubbing down with water etc

M&L rendering 15mm thick in Cement Mortar 1:4 on fair faces of brick or concrete, external surfaces of walls finished and even & fair without using extra cement complete all as specifed & as directed.

M&L rendering 15mm thick in Cement Mortar 1:6 on other than fair faces of brick surfaces of walls finished the surface even & Smooth without using extra cement complete all as specifed & as directed.

M&L 10 mm thick plastering in Cement Mortar 1:3 finished even and smooth w/o using extra cement on brick surface of ceilings complete all as specifed & as directed.

M&L for preparing the newly plastered wall surface then applying 2mm thick wall care putty followed by two coat of oil bound distemper over one coat of alkali resistant primer complete all as specified and directed.

M&L for two coat of oil bound distemper including prepration of new ceiling surface and priming plastered surfaces with alkali resistant priming paint over 1 mm thick wall care putty complete all as specified and directed.

M & L for preparing the newly plastered wall surface and applying two coat of cement base pant over one coat of cement primer complete all as specified and directed.

M & L for complete removal of existing treatment from old decorated wall surface by scrapping with electric regmal machine/hand scrapper then applying 2mm thick wall care putty followed by two coats of Oil bound distemper over one coat of alkali resistant primer of any tint on walls complete all as specified and directed.

M & L for complete removal of existing treatment from old decorated ceiling surface by scrapping with electric regmal machine/hand scrapper then applying 1mm thick wall care putty followed by two coats of Oil bound distemper over one coat of alkali resistant primer of any tint on ceiling complete all as specified and directed.

M&L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 white cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove of uniform size 15mm wide and 15mm deep in the top layer all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings .complete all as specified.

Taking up or down 25mm bore steel tubing and connections, including cleaning for refixing or removal to store

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store

Refixing old 25mm bore steel tubing and connections in new or old position (Walls, ceiling, floors, etc.complete.

S & F 25 mm bore galvanized steel tubing medium grade with all fitting and fixed to walls and ceiling or laid in floors complete all as specified and as directed.

S & F 20 mm bore galvanized steel tubing medium grade with all fitting and fixed to walls and ceiling or laid in floors complete all as specified and as directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings with outer dia 20mm on walls/ceiling or laying in floors complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding and rubbish off the premises complete all as specified and as directed.

M & L for Non-skid Coloured Ceramic tiles 7 to 8 mm thick (Square/rectangular) area of tile exc 0.11 Sqm but not exceeding 0.18 Sqm in floors, set and jointed in neat cement to match the shade over and including 15 mm thick screed bed in CM 1 : 6 complete all as specified and as directed.

M & L for Coloured Glazed ceramic tiles in vertifical surface 600 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in colour cement to match over and including 10 mm th rendering in CM 1:4 complete all as specified and as directed.

S & F in repair Vitreous China wash down water closet pan (pedestal pattern) of size 580 mm white with ‘P’ or ‘S” trap, any pattern including Seat Cover (excluding flushing cistern and flush pipe) complete all as specified and as directed.

S & F in repair Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white premier quality, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, etc complete all as specified and as directed.

S & F in repair 10 Ltr PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

S&F in repair Vitreous China Urinal,Half stall type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plug with CP Spinkle and including 60mm long brass screws, complete all as specified and as directed.

S&F in repair Vitreous china urinal partition white of size 310 x 700mm complete all as specified and as directed.

S&F in repair 15mm bore Angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms) complete all as specified and as directed.

S&F in repair PVC connection 15mm bore with PTMT nuts of length 600mm

S&F in repair one piece white Wash Basin with Pedestal fo size 560 x 415 x 820 mm complete all as specified and directed. Make : Prayag Cat No : 4602 or equivalent in Cera/ Parryware/ Hindware.

S&F in repair Waste coupling 32mm bore dia of PTMT half threaded for WHB complete all as specified and directed.

S&F in repair Waste coupling 32mm bore dia of PTMT half threaded for urinal complete all as specified and directed.

S&F in repair PVC Urnial Waste Pipe 32 mm dia for urinal complete all as specified and as directed. Make : Prayag Cat No345 or equivalent.

S&F in repair PVC Solid Waste Pipe 32 mm dia for WHB complete all as specified and as directed. Make : Prayag Cat No : 3271 or equivalent.

S&F in repair CP Bib Cock 15mm long body with flange complete all as specified and as directed. Make : Prayag Cat No : 6508 or equivalent in Cera/ Parryware/ Hindware.

S&F in repair CP Soap Dish including chromium plated brass screws and plastic cleats complete all as specified and as directed. Make : Prayag Cat No : BA-05 or equivalent in Cera/ Parryware/ Hindware.

S&F in repair 600 mm long CP Tubular Towel Rail 20mm dia complete all as specified and as directed. Make: Prayag/ Cera/ Parryware/ Hindware.

S & F in repair 15mm bore WHB Mixture with swan neck complete all as specified & as directed. Make : Prayag Cat No : PIS-02 or equivalent in Cera/ Parryware/ Hindware.

S & F in repair 80 mm dia CP Overhead RODIO Shower (with Arm) complete all as specified and as directed. Make : PRAYAG Cat No : BOS-103 or equivalent in Cera/ Parryware/ Hindware.

Dismantling water tanks exc 250 & n exc 500 ltr capacity and removing to store complete all as specified and as directed.

S&F 500 ltr Rotational moulded Polyethylene water storage 3 layered tank (Cylindrical vertical with closed top) hoisted and fixed in position all as specified and as directed.

S&F in repair 20 mm bore dia Gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

S&F in repair 20mm bore dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwedfor iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0mm-210gms./ 25mm-455gms/ 40mm - 690 gms) complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

M & L for Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

Taking down chowkhat or frame without taking off shutters of any description n.exc 1.5 sqm each for ventilators complete all as specified and as directed.

Taking down chowkhat or frame without taking off shutters of any description exc 1.5 sqm and n-exc 4 sqm each complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelam PVC sheet reinforced with MS Square tube, supplying & fixing in opening as per specification.

S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face supplying & fixing in frame at site as per specification.

S&F 150 mm Aluminium handles, cast type anodised complete all as specified and directed.

S&F stainless Steel 100mm butt hinges anodised and fixed type B-21 complete all as specified.

S&F 200mm aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F 250mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and as directed.

M&L for One coats of synthetic enamel paint on old wooden Surfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed.

M&L for One coats of synthetic enamel paint on old Steel Surfaces width or girth exc 10cm including preperation of surfaces complete all as specified and directed.

Hacking out old broken glass (any thickness) from metal frame/aluminium frames including punching or drilling out old galzing pins complete all as specified & directed.

S & F 4.0 mm thick ordinary glass glazing with oil putty in square n exc 0.5 Sqm in each pane or rubber beading as required complete all as specified & directed.

Dismantling of CI/PVC pipes & fitting of any description & position up to 100 mm dia complete all as specified & directed.

S&F PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed

S&F PVC (SWR) 75 mm bore pipe single socketed, in any length with rubber ring jointes , laid in trenches or in floor complete all as specified and directed.

S&F PVC (SWR) 110 bore pipe single socketed, in any length with rubber ring jointes, laid in trenches or in floor complete all as specified and directed.

S&F PVC (SWR) 110 bore pipe single socketed, in any length with rubber ring jointes ,fixed to wall complete all as specified and as directed.

S&F PVC (SWR) floor trap 75 mm dia, plain with grating including jointing with solvent cement complete all as specified and as directed.

S & F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed.

S&F 75mm bore PVC(SWR) vent cowl complete all as specified and directed.

S&F 110 x 75 mm PVC(SWR) reducers complete all as specified and directed.

S & F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays for 75 mm bore pipe, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed.

S & F Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays for 100mm bore pipe, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

Demolition and breaking up drain pipes (Salt glazed stoneware)/pvc set in cement mortar 150 mm internal dia of pipe complete all as specified and as directed.

M&L for Cutting into existing manholes for connecting new drains 150mm dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains 200mm dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed.

M&L for 150mm nominal size (DWCPE) Double wall corrugaged poly ethylene pipe ((SNB) including all fixing accessories of fittings like socket/spigot joint with elastomeric sealing ring, rubberring, SILAID rubber lubricants required for laying of pipes, laid in trenches, complete all as specified and as directed.

M&L cement mortar concrete bed to drain pipes in PCC 1:3:6 type C-2 (using 40 mm graded crushed stone agg) incl packing under and against the sides of pipes after they are laid and tested in bores of pipe150mm dia complete all as specified and as directed.

S& F in repair 75mm thick factory made SFRC manhole/ drain covers of approved shape & size complete all as specified and as directed. Make : Polycrete or equivalent.

M&L 75 mm thick PCC 1:3:6, type C1, using (20mm graded aggregate) as in Plinth protection and finished the surface fair & even without using extra cement, laid in panel , including filling the joints with sand mixed with bitumen in 1:1 ration complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 sq m on plan and n exc 1.5 m in depth and getting out complete all as specified and as directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded agg) in foundation filling, sub base and mass concrete filling etc. complete all as specified and as directed.

M & L for RCC type B1 1:11/2:3 Using 20mm graded stone aggregate in fdn filling and mass concrete complete all as specified and as directed

Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions for fair finisghed surfaces complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

S & F plain/chequered MS plate incl cutting / welding & drilling confirming to Fe-290( Gde -165)complete all as specified and directed.

S&F steel tubular trusses, purlins, rafter vertical post and similar works including special shaped washer etc. complete using ERW or induction butt weled tubes including cleats, plates, hold fast and including conforming to IS 1161-1998 Gde st-240 complete all as specified and directed

S&F pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 10 cm and n exc 15 cm long (Dia of neck 11 to 15 mm) complete all as specified and directed

M&L for painting steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described, applying two coats of synthetic enamel paint over coat of red oxide primer including preparation of new surface complete all as specified and directed

Surface dressing not exceeding 15 Cm deep and getting out in Soft/ Loose soil complete all as specified and as directed.

M&L for hardcore of broken stone or boulders guage n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

Supply and laying dry river sand for cushioning to interlocking paver block including punning down of sand complete all as specified and as directed.

M&L for 80mm thick, Machine pressed precast concrete interlocking rubber moulded paver block any shape, colour and size conforming to IS 15658-2006, M-40 Grade, with grey cement and pigment complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment conforming to IS 15658-2006 of 60mm thickness, M-35 Grade complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate for kerb stone, packing of side, edges, coping and similar work including all necessary form work complete all as specified and as directed.

S&F Kerb stone of 450x300x 150mm thick precasted plain cement concrete type B0, 1:2:4, using 12.5mm graded crushed stone aggregate incl earth work for laying kerb stones complete all as specified and as directed.

M&L for repairing of spelled concrete from RCC surfaces (such as ceiling beams, columns, parapets, chajjas etc) in the following stages:- (a) Preparation of existing surfaces like chipping of unsound weak/loose concrete with electric hammer or manually including tapping all edges, making square shoulder of cavities etc not exc 50mm thickness, removal of dabrises complete all as specified and directed. (b) Applying rust remover cum passivators sika rust off 100@ 0.20Kg/Sqm each coat as per manufacture instruction to remove rust from existing reinforcement (Make: Sika or equivalent). (c) Mixing and applying two components epoxy resin concrete bonding coat of Sikadur (R&R 42)-@ 0.40Kg/Sqm (mixing proportion as per manufactures instructions) including preparation of surfaces by chipping and thorougly cleaning of surfaces complete wherever required over new reinforcement (if required) and as directed by Engr-in-Charge. (Make: Sika or equivalent) Reinforcement shall be measured and paid separately. (d) Applying the prebached one component polymer modified cementious patch repair mortar n exc 50mm in layers of 15mm thick each of product Sika Mono Top 122F as per manufactures instructions to match with existing surface as in sides and soffits etc of slabs Chajjas, Fins, Facias, Parapets, Lintels, Columns and Beams etc complete including necessary scaffolding, shuttering, necessary chases to brick work or RCC members at any height upto 6 storey building including removing of small trees shrubs etc all as specified and as directed by Engr-in-Charge.

S&F Glass Brick of size 190mm x 190mm x 80mm set and pointed with adhesive and grounting powder including glass block spacers, GI wire, other connected items and MS frame work all around the brick walls complete all as per manufacturer instruction and specified and as directed.

M&L demolition of concrete of any description and in any position not otherwise specifically provided for.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in any soft soil complete all as specified and directed.

Removing excavated material to a distance exc. 50m and depositing where directed at a level n exc. 1.50m above the starting point.

M&L 75mm thick PCC 1:4:8 type D2 (40mm graded stone agg) as in base to receive floor finishes etc complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type D2 (40mm graded stone agg) as in sub base to receive floor finishes etc complete all as specified and directed.

Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete (fitting such as switches, ceiling roses, pendent, regulator socket etc shall be measured and paid separately) and making good disturbed surfaces of wall floor etc complete all as specified and as directed.

Taking down old and unserviceable sub main wiring and removing from the site and making good the disturbed surface complete all as specified and directed.

M&L point wiring for modular switches with 1.5 sqmm , single core , multi stranded copper conductor PVC insulated and unsheathed (FRLS) cable 1100 Volts grade, drawn through concealed Conduit 25 mm as requirement of site including cadmium plated screws as per ISI, 1.5 sqmm , single core , multi stranded copper conductor PVC insulated and unsheathed (FRLS) cable 1100 Volts grade as earth continuity conductor to common earth and connecting to earth dolly for One light/ fan point controlled by one switch 5 Amps one way single pole complete all as specified and directed. Make- Polycab/Havells/Finolex.

All as per item No. 117 here in before but for one three pin, 5 Amp, socket out let on independent board

All as per item No. 117 here in before but for one three pin, 5 Amp, socket out let on same board

All as per item No. 117 here in before but point wiring with 2.5 Sqmm, multistranded, copper conductor cable, for 15 Amps socket outlet on independent board with 2.5 Sqmm size earth conductor

All as per item No. 117 here in before but point wiring with 4 Sqmm, multistranded, copper conductor cable, for AC point on independent board with 4 Sqmm size earth conductor

S&F in replacement modular cover plate with frame, 3 modules complete all as specified and as directed.

S&F in replacement modular cover plate with frame, 6 modules complete all as specified and as directed.

S&F in replacement modular cover plate with frame, 12 modules complete all as specified and as directed.

S&F in replacement modular metal flush box, 3 modules complete all as specified and as directed.

S&F in replacement modular metal flush box, 6 modules complete all as specified and as directed.

S&F in replacement module metal flush box, 12 modules complete all as specified and as directed.

S&F modular switch, 1 way, 6 Amp, 1 Module, complete all as specified and as directed.

S&F modular Socket, 6Amp, 2/3 Pin, combined, 2 module complete all as specified and as directed.

S&F modular switch, 1 way, 16 Amp, 1 Module, complete all as specified and as directed.

S&F modular Socket, 16/6 Amp, 3/5 Pin, combined, 2 module complete all as specified and as directed.

S&F modular Fan step regulator, 120W - 1 module complete all as specified and as directed.

S&F Ceiling rose, PVC/ polycarbonate, isolated body type, three terminal, 240 volt, fixed in position & connecting complete

S&F in replacement sub main wiring with 2 runs of 6 Sqmm FRLS, single core, PVC insulated & unsheathed cable, 1100 Volts grade, with multi stranded, copper conductor, drawn through and including 25 mm dia, concealed, PVC rigid, non metallic conduit, medium grade, as per IS, with all fittings and one run of 6 Sqmm FRLS, single core, PVC insulated & unsheathed cable, 1100 Volts grade, with multi stranded, copper conductor as earth wire complete all as specified and as directed. Note:- Two run of cable along with earth conductor including PVC rigid conduit shall be measured as one RM length).

S&F in repair load line, distribution board, double door type, TPN, vertical, 8 way, suitable for accomodating upto 125 Amps MCCB with incomming frame three pole, including 250 Amp copper bus bar, neutral link, blanking plates etc complete all as specified and as directed.

S & F in repair for distribution board double door type, SPN, 12 way, complete including 200 Amps rated bus bar, neutral link, blanking plates etc complete all as specified and directed.

S&F in replacement Bldg security light fitting LED 25 Watt, highly efficient IP66 LED, high power having aluminium pressure die cast housing and PC cover in the front and high power lens for batwing light distribution with electric connection with suitable size of PVC insulated copper wire including GI bracket 1.5 Mtr with clamps and bolts complete all as specified and directed. Make : ORIENT Model No :- LSFS-25-CF-PC / Philps/ wipro

Supply, fixing and connecting in replacement of Slim LED Batten 10 watt with Surface/Wall Mounted integrated LED 2 feet Fitting Polycarbonate housing and diffuser with viewing angle of 120 degree used to enhance the luman output Height suitable for White Housing & Isolated Electronic Driver, with Output Short-circuit protection, Surge Voltage protection up to 2.5 KV . Total system Lumen of 10W Led should be 1000 or above in Cool day Light(6500K), Power factor>0.9, CRI (Ra) >80, System with Average life of 50000 Burning hours complete with all accessories as required complete all as specified and as directed.Make : ORIENT / Philps/ wipro

Supply, fixing and connecting in replacement of Slim LED Batten 20 watt with Surface/Wall Mounted integrated LED 4 feet Fitting Polycarbonate housing and diffuser with viewing angle of 120 degree used to enhance the luman output Height suitable for White Housing & Isolated Electronic Driver, with Output Short-circuit protection, Surge Voltage protection up to 2.5 KV . Total system Lumen of 20W Led should be 2000 or above in Cool day Light(6500K), Power factor>0.9, CRI (Ra) >80, System with Average life of 50000 Burning hours complete with all accessories as required complete all as specified and as directed.Make : ORIENT Model No :- LBLN-20-C- SQ/ Philps/ wipro

M&L Earthing complete with galvanised Iron earth plate eletrode 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25mtrdeep below GL) with top edge of the plate not less than 1.5 metre below normal grond level, surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all round the plate with using 4mm dia GI wire as earth wire electrode welded and revetted to earth plate at one end connected to main DBs of Building at another end GI earth wire encased in and including 15mm bore GI light grade pipe through upper end of earth plate upto main DB of bldg, with 20mm bore GI pipe light grade as water pipe from earth chamber to upper edge of earth plate, MS funnel with wire mesh fixed on water pipe including execvation earth work, Provn of PCC pit in PCC 1:2:4 type B-1 chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type BI duly reinforeced with MS bars 8mm dia @ 150 mm centre to centre, both ways complete with lifting handle all as shown in electrical plate No 3 of SSR of part-I complete all as specified and as directed.

S&F in repair modular blanking plate, 1 Module complete all as specified and as directed.

Supply and fix in repair for PVC T-COVER complete all as specified and as directed.

S& F in replacement Exhaust fan 300 mm sweep 240 Volt Heavy duty (Iron), 1375 RPM , with suppoting frame connection with flexible PVC copper wire from ceiling rose to exhaust fan including provn of opening of hole on brick wall and grouting nut and bolt of suitable size complete with minimum two year warranty on Product all as specified and directed.MAKE- BAHAR 300 MM METALLIC GREY EXHAUST FAN BAJAJ/ Havells/ CG Note :- Old unserveciable exhaust fan will be deposited to MES store yard.

Supply and Fixing in replacement Geysers of cap. 25 Ltr, five star BEE rating , Electric Driven, Single phase, 240 V, Storage vertical type and heating element 2 KW, inner shell Glass lined enamel coated incoloy heating elements , temperature indicating dial , tank design is suitable to withstand 8 bar pressure, shock resistant ABS outer body automatic cutoff , including electrical and water connection with hot and cold water connection pipe (PVC type) and fixed on the wall with mild steel fastner 150 mm long and 10 mm dia with pin and bolts complete with minimum two year warranty on Product all as specified and directed. Make: BAJAJ (CALENTA )/ HAVELLS/ /USHA.Note :- Old unserveciable Geyser will be deposited to MES store yard.

Supply & fix in replacement ceiling fan (White colour) 230 V, 1400 mm sweep,speed 400 RPM , having rod length 300 mm complete all as specified and directed by Enggr in charge.Make- Havells/Bajaj/Orient. Note :- Old unserveciable celing fan will be deposited to MES store yard.

S&F in replacement sheet metal enclosure with socket plug top, single pole and neutral enclosure with a two pin earth plug and socket complete with one MCB of capacity 20 Amps , 240 Volts complete all as specified and directed.

S & F in repair MCCB 415 V, 125 Amps, 25 KA, 4 Pole complete all as specified and directed.

S & F in repair MCB DP, 240 Volts, 40 Amps complete all as specified and directed.

S & F in repair MCB SP, 240 Volts, 10 Amps complete all as specified and directed.

S & F in repair MCB SP, 240 Volts, 16 Amps complete all as specified and directed.

S & F in repair MCB SP, 240 Volts, 32Amps complete all as specified and directed.

M&L point wiring with 1.5 sqmm (nominal area) copper conductor FRLS cable (multi-stranded) PVC insulated and unsheathed electric cable 1100 Volts drawn through PVC casing and caping of suitable size (as per conductor run) with all fittings and accessories and including PVC insulated unsheathed electric cable 1100 volts 1.5 sqmm (multi-stranded) copper conductor single core (green colour) as continuous earth wire connected to common earth dolly encluding 50mm deep box made out of 2nd class hard wood board of suitable size and shape and other boxes for mounting light fittings etc covered with 3mm thick plastic laminated Hylum ISI marked for follwoing complete all as specified and directed:-

One light point controlled by one 5 Amps one way switch.

One 3 pin socket outlet 5 Amps on same board

S&F wall mounted LED spot light fame type long life 30000 burning hours with CRI >80 ,12 watt capacity connecting to ceiling rose with three core twisted flexible copper cable of suitable size complete all as specified and as directed by Engr-in-Charge. (Make: CG Cat Part No CDR-212-12-40-SL-NWH or equivalent in Havells/ Philips/ Wipro)

M & L for wiring with two single core 6.00 sqmm stranded copper conductor PVC insulated and unsheathed cable ISI marked in 25 mm dia, medium grade, in PVC casing and capping main connection including 4 sqmm PVC insulated unsheathed copper conductor ISI marked as earth wire complete all as specified and directed.

S&F MCB DB sheet enclosure,DoubIe door type, single pole and neutral 240V with 200 Amp rated bus bar suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated complete confirming to IP 42/43 without MCB and with enclosure blank plates for unused way suitable for 4 way complete all as specified and directed.

Supply and fixing 240V, 10KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning all as specified and directed

Supply and fixing MCB SPN 240V, 10KA 'C' curve 32 Amp current carrying capacity in the MCB DB complete with connection testing and commissioning all as specified and directed.

Vishal Traders

M/s Durga Traders

M/S Rohit Enterprises

S D Constructions

imran construction company

VIJAY KUMAR GUPTA

THE LOTUS BUILDTECH

friends associeates