SPECIAL REPAIRS REPLACEMENT TO SECURITY FENCING FOR CERTAIN UNIT OF EW BN, PROVN OF PAVED AREA FOR TRG ACTIVITES FOR EW BN AND PROVN OF CERTAIN REVUNUE WORKS AT RAYANG MIL STN UNDER GE 872 EWS

Amount

Dismantling Posts or Struts (Steel or RCC) any Section, embedded in Natural Ground and Taking out embedded Portion of Posts or Struts including necessary Earthwork (as required at Site of Work) and Making Good Disturbed Ground, complete all as specified and as directed.

Dismantling Posts or Struts (Steel or RCC) any Section, embedded in Cement Concrete and Taking out embedded Portion of Posts or Struts including necessary Earthwork (as required at Site of Work) and Making Good Disturbed Ground, complete all as specified and as directed.

Demolition Brick Work or Pre-cast Concrete Block Masonry, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Dismantling Wrought Iron or Mild Steel Work of any description not otherwise provided for, Segregating Serviceable Mild Steel and Stacking properly at Sites and Keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling Structural Steel Work including Doors, Gates but excluding Framed Truss, etc., Segregating Serviceable Mild Steel and Stacking properly at Sites and Keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling Fencing Wire Mesh of any description, complete all as specified and as directed.

Dismantling Barbed Wire of any description, Segregating the Serviceable Barbed Wire and Stacking properly at Sites and Keep in Safe Custody for re-use, complete all as specified and as directed. NOTE : Each Line of Barbed Wire will be Measured for Payment.

Surface Dressing not exc. 15 Cm Deep in Soft/ Loose Soil and getting out, complete all as specified and as directed.

Excavating in Post Holes (or Similar Holes) in Soft/Loose Soil, each not exc. 0.50 CUM, getting out and Removing surplus Soil to a distance not exc. 50.00 Metre and Making Good Surfaces, complete all as specified and as directed.

Removing Excavated Materials (Soils) to a distance not exc. 50.00 Metre and depositing where directed at a level not exc. 1.50 Metre above the Starting Point, complete all as specified and as directed.

M&L Sand Gravels (as approved) Filling under Floors or in Foundations in layers not exc. 15 Cm thick including Watering and Consolidation, complete all as specified and as directed.

M&L Hardcore with Broken Stone or Boulder, Gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15 Cm thick, watered and well rammed to a True surface, complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (40mm graded aggregate) for embedding Mild Steel Work as Fencing Posts, etc. in Foundations, Filling and Mass Concrete, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deem to be include in the Quoted Unit Rate.

M&L Pre-cast Cement Concrete Block Masonry with Solid Blocks of Size 300x200x200mm or 300x200x100mm, having Compressive Strength of not less than 100 Kg/ Sq Cm (as per IS-2185) in Cement Concrete 1:3:6 (20mm graded stone aggregate), exc. 10 Cm in Width and Setting in Cement Mortar 1:6, complete all as specified and as directed.

M&L Mild Steel Works such as Posts and Struts in Fencing including cutting Tops to shape as directed, drilling holes, notching for Wire, etc.; including all necessary drilling, bolting or riveting, etc. and similar Work, conforming to Fe-290, Gde-E-165, complete all as specified and as directed.

M&L Mild Steel Round Bars 10mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Re-fixing Mild Steel Round Bars 10mm dia and over (Serviceable Mild Steel Round Bars obtained from BOQ Item No. 4 here-in-before), cut to length bent to shape required, including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Mild Steel Flat Iron 40x4.0mm (Fillet for securing Wire Mesh, etc.) cut to length including all necessary drilling, bolting or riveting, etc. and Similar Work, conforming to Fe-290 Gde E-165, complete all as specified and as directed.

M&L Re-fixing Mild Steel Flat Iron 40x4.0mm (Fillet for securing Wire Mesh, etc.) (Serviceable Mild Steel Flat Iron obtained from BOQ Item No. 4 here-in-before), cut to length including all necessary drilling, bolting or riveting, etc. and Similar Work, conforming to Fe-290 Gde E-165, complete all as specified and as directed.

M&L Rolled Mild Steel Framed Work as in Doors or Gates of Angle or Other Section with Gusset Plates, Rails, Braces, etc., drilled for fixing of Steel Sheeting or Other Covering. Doors, etc. to be prepared for hanging or sliding with and including either Hooks and Hinges or Steel Hanging Door Fittings (exclusive of Steel Sheeting or Other Covering, Running Rails and Guides) and hanging; also fastening and fixing, conforming to Fe-410-W (Gde E-250), Quality A, complete all as specified and as directed.

M&L Mild Steel Tublar Trusses, Rafter, Purlins, etc. including Special Shaped Washers, etc. complete using ERW or Induction Butt welded Tubes, confirming to IS:1161-1979, Grade St-240, complete all as specified and as directed.

M&L Plates (Plain or Chequered) Channels, Square cut or notched (Ordinary and Counter Sunk) forming Holes, without any attachment, conforming to Gde Fe-410-W (Gde E-250) Quality 'B', complete all as specified and as directed.

M&L Mild Steel Screw Bolts (Machine made) of any description or Size, with Hexagonal or Square Heads at One End and screwed the Other End, or screwed Both Ends, Each screwed End to be fitted with Washers and One Hexagonal or Square Nut, complete all as specified and as directed.

Supply only Mild Steel Galvanised Security Chain Link Fencing 100x100mm or 75x75mm Mesh with 4.0mm Nominal dia Mild Steel Galvanised Wire and both Ends without Knuckling/ Twisting, complete all as specified and as directed.

Fixing only Chain Link Fencing including Line Wires, any mesh, size and type to any type of Standards, Rails, Straining Bolts, etc. including Provission of Mild Steel Binding Wire (annealed) not less than 0.90mm dia, complete all as specified and as directed.

S&F Galvanised 2 Strand, Steel Barbed Wire 2.24mm dia barbed with 2mm dia Barbs at 75mm spacings and straining and fixing to any type of Standard Rails straining Bolts, including securing or tying at crossings with and provision of Galvanised Mild Steel Wire, Staples or Steel Pins, etc., complete all as specified and as directed. NOTE : Each Line of Barbed Wire will be Measured for Payment.

S&F Re-fixing Galvanised 2 Strand, Steel Barbed Wire 2.24mm dia barbed with 2mm dia Barbs at 75mm spacings (Serviceable Barbed Wire obtained from BOQ Item No. 1.002 here-in-before) and straining and fixing to any type of Standard Rails straining Bolts, including securing or tying at crossings with and provision of Galvanised Mild Steel Wire, Staples or Steel Pins, etc., complete all as specified and as directed. NOTE : Each Line of Barbed Wire will be Measured for Payment.

M&L Roughening Surfaces of Old Concrete Floor by Picking, Sweeping Clean and Washing down with Water to Remove Dust, etc. and Brushing Neat Cement Slurry with 3.0 Kg of Cement Per Squre Metre, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (40mm graded stone aggregate) 75mm thick in Footpaths, etc., laid in Alternate Panels, complete all as specified and as directed.

M&L Chequered Cement Concrete Coloured (Terracota Red or Yellow) Tiles 200x200x25mm/250x250x25mm thick, Set and Jointed in Neat Cement Slurry in Floors and Pointed in Grey Cement, laid over and including 15mm thick Cement Screed Bed in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Screed Bed will deem to include in the Quoted Unit Rate.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 150mm thick in Sub-base to Floors, etc., complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 100mm thick in Flooring, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without Using Extra Cement, complete all as specified and as directed.

M&L Forming 12mm thick Expansion Joints in Concrete Slab/Flooring 100mm thick, filled with Pre-formed Bituminous Filler and Top 30mm Primed and sealed with Sealing Compound, Grade ‘B', complete all as specified and as directed.

M&L Forming Contraction (Dummy Joint) 65mm Deep x 10mm Wide and filled with Sealing Compound Grade 'A', complete all as specified and as directed.

M&L Road Marking with Reflective Thermoplastic Paint 2.5mm thickness in Single Coat in White/ Yellow by in Digamous Modern Propelled Road Marking Machine with and including Glass Beats, coforming to BS:6088 and MOST Specifications including Cleaning of all Dirts, Scale, Oil, Grease and Foreign Materials, etc., complete all as specified and as directed.

M&L Rendering 10mm thick in Cement Mortar 1:4 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smoooth without Using Extra Cement, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint (of approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, over exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing Old Treated Steel and Iron Surfaces of any descriptions, over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing New Steel and Iron Surfaces of any description, not exc. 10 Cm in Width or Girth, not otherwise described and applying Two Coats of Synthetic Enamel Paint (1st Grade/ Quality) over a Coat of Red Oxide Zinc Chrome Primer complete all as specified and as directed.

M/s GOURAB JYOTI GOGOI

AFTAB ENTERPRISES

M/S CHANDAN ENTERPRISE