SPECIAL REPAIR TO CERTAIN AIRMEN BILLETS AT AF STN LEH UNDER GE (AF) LEH

Amount

PART-I B/R WORKS Demolition of brickwork or stone/bouder masonry,built in cement mortar or cement lime mortar including all quoins,arches,pillars,etc for ashlar fancings, dressed stonework, precast concrete articles and precast concrete block walling complete all as specified and as directed by Engr-in-charge.

M&L for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar, completeType C1 1:3:6 (20mm graded aggregate) Set in cement mortar 1:6 complete all as specified and directed by Engr-in-charge.

Taking down cement or cement lime plaster any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L Rendering 10mm thick Cement plaster 1:4 on fair faces of brick work or concrete sur faces complete all as specified and directed by Engr-in-charge.

M&L Rendering 10mm thick Cement plaster 1:6 on fair faces of brick work or concrete sur faces rendering is to be finished even and smooth (without using extra lime or cement) complete all as specified and directed by Engr-in-charge.

M& L for Preparation of new plastered surfaces of walls and applying three coats of cement base paint on walls complete all as specified and as directed by Engineer-in-Charge.

M&L for Preparation of new plastered surfaces of walls and applying two coat of distemper oil emulsion white or tinted on walls over a coat of chalk whiting on plastered surfaces ,preparatory to distempring complete all as specified and as directed by Engineer-in-Charge.

M&L for Preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint on steel surfaces complete all as specified and as directed by the Engineer-in-Charge.

M&L for Preparation of old decorated plastered or unplastered surfaces of walls and applying one coat of oil bound distemper on walls complete all as specified and as directed by Engineer-in-Charge.

M&L for Preparation of old decorated wooden surfaces of ceiling and applying one coats of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge.

M&L for Preparation of old decorated plastered or unplastered surfaces of walls and applying one coat of cement base paint on walls complete all as specified and as directed by Engineer-in-Charge.

M&L for Glazed ceramic coloured tiles in vertical surface area exc 0.06 Sqm but n exc 0.15 Sqm of 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with and including Rendering 10mm thick Cement plaster 1:3 on fair faces of brick work or concrete sur faces with and including Dismantling of wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engineer-in-Charge.

M&L for Non - skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including Screed bed or bedding layer of mortar 15 mm 1:4 thick for laying floor finishes with and including Dismantling of floor tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed by Engineer-in-Charge.

M&L Cement concrete in sub bases to floor,sunken floors, filling and mass concreteType D-2 1:4:8 (40 mm graded aggregate) complete all as specified and as directed by Engineer-in-Charge.

M&L Cement concrete in Surface to floor,sunken floors, filling and mass concrete Type B 2 1:2:4 (40 mm graded aggregate) complete all as specified and as directed by Engineer-in-Charge.

M&L 25 mm thick Cement concrete type B-0, 1:2:4 (20 mm graded aggregate) as in sub base or flooring complete all as specified and as directed by Engineer-in-Charge.

M&L 75 mm thick Cement concrete type C-2, 1:3:6 (40mm graded aggregate) as in Plinth protection complete all as specified and directed by Engr-in-charge.

M&L 100 mm thick Cement concrete type B-1, 1:2:4 (20 mm graded aggregate) as in floor complete all as specified and directed by Engr-in-charge.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base of mortar C:M 1:4 of 20mm thick for laying floor finishes laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and including dismantling of Stone slabs and tiles of any description or thickness in floors ,aprons,counters,plateforms etc laid bedded and pointed in any mortar and removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L for kota stone slab 20-25mm thick in riser of steps,skerting, dado and pillar laid over cement screed or cement plaster in 1:4 of 10mmthick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including dismantling of Stone slabs and tiles of any description or thickness in floors ,aprons,counters,plateforms etc laid bedded and pointed in any mortar and removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

M&L Granite 20mmm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, win dow-cills, cooking plat forms,washroom counters and like including Screed bed or bedding layer of mortar 15 mm 1:4 thick for laying including point ing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and Demolition of Stone slabs and tiles of any description or thickness in floors ,aprons,counters,plateforms etc laid bedded and pointed in any mortar and removing rubbish off the premises complete all as specified and directed by Engr-in-charge. .

M&L for Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; including dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc.laid bedded and pointed in any mortar complete all as specified and as directed by Engr-in-charge.

Dismantling of plain or corrugated steel sheeting,any gauge, thickness, including Nanital or similar pattern roof coverings complete all as specified and directed by Engr-in-charge.

S&F for pre–painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm of an colour having tensile strength of 550Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F for pre–painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm of an colour having tensile strength of 550Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F 0.63 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts , in roofs, walls etc. with grade of zinc coating 275.complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 complete all as specified and directed.

S&F for rolled mild steel sections as in column main and joist, channel, angle, or tee sections, fixed independently etc. (cut to ordinary lengths i.e. within 20mm of the length indicated, fixed with angle cleats or other connecting plates of Fe 410-W (Gde E-250) quality A complete all as specified and directed by Engr-in-Charge.

S&F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

M&L 3-layer PP-R Polypropylene random copolymer) concealed pipes Outer diameter of pipes 25 mm SDR 7.4 (PN16) UVstabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc including Taking up or down existing tubing and connections, complete all as specified and directed by Engr-in-Charge.

M&L 3-layer PP-R Polypropylene random copolymer) concealed pipes Outer diameter of pipes 32 mm SDR 7.4 (PN16) UVstabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc including Taking up or down existing tubing and connections complete all as specified and directed by Engr-in-Charge.

S&F in repair Bib taps,15 mm bore fancy type cast copper alloy Chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair Pillar taps,15 mm bore fancy type cast copper alloy, with capstan heads,chromium plated ,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair Stop valves/angle valve , 15 mm bore fancy type chromium plated cast copper alloy, screwed down,high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair Waste fittings, brass,32 /40 mm chromium plated for glazed ware sinks, basins, etc.with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair Waste coupling of PTMT 32/40 mm (half or full threaded) complete all as specified and directed by Engr-in-Charge.

S&F in repair Grating doom 100mm dia of PTMT complete all as specified and directed by Engr-in-Charge.

S&F in repair Grating doom 125 mm dia with waste hole of PTMT complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) 75 mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including all connections & fittings complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) 110 mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including all connections & fittings complete all as specified and directed by Engr-in-Charge.

S&F 75mm bore Sand Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints,fixed to walls including al connection and fittings and including dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar including dismantling old, complete all as specified and directed by Engr-in-Charge.

S&F 100mm bore Sand Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints,fixed to walls and including dismantling of cast iron or reinforced concrete drain pipes, jointed in cement mortar inclusding dismantling old complete all as specified and directed by Engr-in-Charge.

S&F in repair 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed by Engr-in-Charge.

S&F in repair 40mm bore Low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. Cm for WHB fixed with necessary fixing arrangements complete all as specified and directed by Engr-in-Charge.

S&F in repairs counter below Vitreous coloured China wash basin, size 550x400mm , excluding taps, waste, chain and plug and porcelain stopper but including brackets and waste fittings of 40mm complete all as specified and directed by Engr-in-Charge.

S&F in repairs Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges fixed in repair complete all as specified and directed by Engr-in-Charge.

S&F in repair fancy type Premium quality Chromium plated Soap Dish Square or Rectangular complete all as specified and as directed .

Taking down Chowkhats or frames not exc. 1.5 sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed by Engr-in-Charge.

Taking down Chowkhats or frames exc 1.5 sqm but n exc 4 sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed by Engr-in-Charge.

Taking down Shutters of any description n exc 1 sqm each complete all as specified and directed by Engr-in-Charge.

Taking down Shutters of any description exc 1 sqm and n exc 2 sqm each complete all as specified and directed by Engr-in-Charge.

M&L for 2nd class hard-wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered,put together with glue pinned at joints, supplied and fixed complete all as specified and directed by Engr-in-Charge.

M&L for Preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint treating ends of posts, back of chowkhats, etc, area tarred exc 0.1 sqm but n exc 0.50 sqm each complete all as specified and directed by Engr-in-Charge.

M&L for Preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint treating small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats, etc., area n exc 0.1 sqm each complete all as specified and directed by Engr-in-Charge.

M&L for Sanding newly tarred or painted surfaces with clean sharp sand complete all as specified and directed by Engr-in-Charge.

M&L for 30mm thick 2nd class hardwood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered partical board medium density, wood partical board with commercial face veneers: supplied and fitted to chowkhats complete all as specified and directed.

S&F anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, 3 hinges, anodised aluminum snap beading screws etc. complete all as specified and directed.

S&F anodised aluminium window and ventilator shutters, fixed type without sash bar,aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed.

S&F anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.), suitable handle (1no.) complete all as specified and directed.

S&F 12mm thick prelamineted particle board, interior grade, prelamineted one side with decorative choice lamination & other side balancing white lamination, fixed complete all as specified and as directed by Engr-in charge.

M&L for Door shutters with and including chowkhats as per manufacturer specification and instruction of 60 mm thick PUF panel with 0.5 mm thick prepainted galvalume sheet on both side (Colour as approved by GE) including 200mm aluminium tower bolt (2 Nos) aluminium sliding bolt 300mm (01 Nos) built in locking arrangement(mortice lock with handle) and handle 2 nos on both faces fixed with 03 Nos (150mm) heavy duty hinges, fixed with necessary fixing arrangements with existing structure by means of fasteners screws and necessary welded joints including dismantling old complete all as specified and directed by Engr-in-charge.

M&L for Door shutters with and including chowkhats as per manufacturer specification and instruction of 40 mm thick PUF panel with 0.5 mm thick prepainted galvalume sheet on both side (Colour as approved by GE) including 200mm aluminium tower bolt (2 Nos) aluminium sliding bolt 300mm (01 Nos) built in locking arrangement(mortice lock with handle) and handle 2 nos on both faces fixed with 03 Nos (150mm) heavy duty hinges, fixed with necessary fixing arrangements with existing structure by means of fasteners screws and necessary welded joints including dismantling old complete all as specified and directed by Engr-in-charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supply & fixing in opening complete all as specified and directed by Engr-in-charge.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed by Engr-in-charge.

S&F 4.8 mm thick Sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F 4.8 mm Sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane complete all as specified and directed.

S&F 4.8 mm thick Sheet glass, ordinary quality if sheet glass is ground or obscured or frosted, on one side in square exc 0.5 sq. m in each complete all as specified and directed.

S&F 3mm thick polycorbonate sheet fixed to wooden/metal frames with screws with and including taking down old broken sheets from the frame complete all as specified and directed.

S&F 100 mm Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F 125 mm Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F 300 mm Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 100 mm Aluminium anodised,barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150 mm Aluminium anodised,barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 125mm Aluminium handles, cast type, anodised complete all as specified and directed.

S&F 150mm Aluminium handles, cast type, anodised complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description exceeding 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-Charge.

S&F in repair for aluminium (die cast body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

M&L for Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

M&L for Anodised aluminium grill of approved design/pattern, with approved standard section and fixed to the existing window frame with suitable screws, including cutting the grill to proper opening size of fixing and operation of handles and fixing approved anodised aluminium standard section around the opening including dismantling old, all complete as per requirement and direction of Engineer-in-charge

Providing & fixing false ceiling with semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles at all height with GRG (Glass fiber reinforced Gypsum) false ceiling tiles of size 595x595 mm of approved texure, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRCO.50 as per IS 8225:1987, Noncombustible as per BS 476(part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @ 120 grams per sqm inculding both sides) comprising of maint runners of size 15x32mm of length 3000mm, cross-T of size 15*32mm of length 1200mm and secondary intermediate cross-T of size 15*32 mm of length 600mm to form grid module of size 600*600mm, suspended from ceiling using galvanized mild steel items (galvanized @ 80 grams per sqm) ie 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85x25x 2mm Galvanized iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wall wood screws including dismantling of wall and ceiling boards(fibre,pulp,insulation,etc.) or insulation boards /slabs/blankets,any thickness including cover fillets The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.

Removing building debries (other than spoil) to a distance of upto 5Km, beyond the lead included in the rates, including loading, unloading and stacking at the destination complete all as specified and directed by Engr-in-Charge.

M&L for Reinforced cement concrete type B-1 1:2:4 (20 mm graded aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engr-in-Charge.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed by Engr-in-Charge.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.

M&L for hardcore of guage exc 63mm but n exc. 100 mm, deposited,spread and levelled in layersn exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed by Engr in charge.

S&F Rolled mild Steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and directed.

S&F Rolled mild Steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.11611979 grade St.-240 complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finish smooth & even without using extra cement all as specified and directed.

M&L for preparation new plastered wall surfaces and applying two coat of cement paint complete all as specified and directed.

S&F 60mm thick PUF panels in wall with 0.5mm prepainted galvalume sheet on both face/side including all fixing arrangements as in replacement of old unserviceable damaged portion of wall panel complete all as per specification and as directed by Engr–in–Charge.

PART-II E/M WORKS Taking down carefully existing copper / aluminium point wiring for light / fan / bell / socket 5/15 Amp points complete with fitting and fixtures such as switches, sockets, ceiling roses, holders and bracket fittings with battens / conduits / wires and making good the disturbed surfaces of walls and roofs etc.and to match with existing colour complete all as specified and directed.

Material and labour for point wiring for one light/fan /bell point controlled by one switch one way in and including PVC conduit or cassing capping as per site requirement using FRLS (ISI marked) PVC unsheathed multi strand copper conductor cable 1.5sqmm single core for one light/fan point/ bell point controlled by one switch including 3mm thick plastic laminated sheet cover over PVC/wooden box for earth continuity insulated PVC unsheathed (green colour) 1.5sqmm copper earth wire connected to common earth duly using complete all as specified and directed . Note : (a) wiring shall be done by using proper colour coding.

All as per item No 100 here-in-before but for 06 Amp switch/socket outlet on independent board complete all as specified and directed

All as per item No 100 here-in-above but for 16 Amp switch/socket outlet on independent board of cable size 2.5Sqmm complete all as specified and directed

S&F in replacement of switch socket combination with PVC box 2-in-1 3 pin 6 Amps, flush type 230 volts complete all as specified and directed

S&F in replacement of switch socket combination with PVC box 2-in-1 3 pin 16 Amps, flush type 230 volts complete all as specified and directed

S&F in replacement of switch piano, flush type 5 Amps one way 230 volts complete all as specified and directed

Supply and fix in replacement of ceiling rose Bakelite white/black coloured of size 25x50mm two to three terminals, complete all as specified and as directed.

S&F in replacement of LED lights fitting 1x20W, 220V, AC decorative type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

S&F in replacement of LED adore lamp 9/10Watt, B22 base 6500k CDL type with and including holder insulated body pin type complete all as specified and directed

S&F in replacement of Energy saving new generation Endura Rugby Neo - IP65, 10W LED IP65 bulkhead luminaire with opal diffuser, etc complete with all accessories rewired electrically connected in and including taking down of old unservicable fitting, complete all as specified and direcred. Make:- Philips cat part No. WT202W LED 10S CW PSU S3 PC or equivalent in Havells/Bajaj/Wipro

S&F in replacement of ENDURA slim pro plus 2'x2' panel 36 W LED fitting 5700K with LED prisumatic optical modular luminaire suitable for reccesses mounting complete with HF electronic driver complete all as specified and directed, complete all as specified and direcred. Make:- Philips cat part No. RC370B LED36S-6500 G6 L60W60 PSU OD V3 or equivalent in Havells/Bajaj/Wipro

Material and labour, sub main wiring with two single core 4Sqmm (nominal area) PVC insulated and unsheathed cables with stranded copper conductor FRLS (ISI marked) , drawn in and including PVC casing capping with all standard accessories including one run of continuous PVC insulated stranded copper conductor FRLS cable 4Sqmm (nominal area) for earth continuity including taking down old, complete all as specified and directed. Note(s) :- 2runs of 4Sqmm main cable + 1 run of earth cable shall be measured as one unit/one Running Metre.

Supply and fix in repairs MCB TPN 63 Amps, 415V, 10kA "C" curve (ISI marked) complete all as specified and directed.

Supply and fix in repairs MCB SPN 32 Amp, 240 volt-10KA "C" curve (ISI marked) complete all as specified and directed

Supply and fix in repairs MCB SP 6 to 32 Amp, 240 volt-10KA "C" curve (ISI marked) complete all as specified and directed

S&F in replacement of exhaust fan plastic body, 250mm (12") sweep, single phase, 230 volts, 50 Hz AC, 1400RPM, energy saving, heavy duty totally enclosed, heavy duty motor with die-cast aluminium rotor mounted on two ball bearings complete with louvers and shutters including cutting hole for fixing exhaust fan to puf panel, connecting electrically using 3 core 0.75 Sqmm PVC insulated flexible copper conductor cable over all sheathed all as required at site complete all as specified and directed

S&F in replacement of sheet metal enclosure single door for DB's SPN 8 way 240V having 100A rated bus bar complete all as specified and directed

S&F in replacement of sheet metal enclosure single door for DB's TPN 4 way 415V having 200A rated bus bar complete all as specified and directed

Excavation in trenches in any type of soil not exc 1.5m wide and n.exc 1.5m in depth for under ground electric power cables and getting out complete all as specified and directed.

Returning, filling in. including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick in any type of soil complete all as specified and directed

Removing excavated surplus material to a distance exc 50m but n.exc 100m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Material and labour, sand cushioning with a layer of dry river sand, 80mm thick before laying of cable and 150mm thick (punned down to 100mm thick) after laying of cables, in trenches/ducts, complete all as specified and directed. Note : Punned down thickness (overall 18cm), shall be considered for measurement and payment.

Supplying and laying, factory made unreinforced precast concrete cable cover LV type-1, flat, of size 250x150x40mm, ISI marked for protection of LT cable , complete all as specified and directed.

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated, armoured, heavy duty, electric power cable (ISI marked) , cross sectional area 35 Sqmm 3.5 core aluminum conductor 1100volts grade underground cable ISI marked including both side connection with cable lugs etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc including taking down old unserviceable XLPE cable complete all as specified and as directed. Note(s): (i) Excavation & earth work, sand cushioning and PCC cover for protection of cable shall be measured and paid separately.

Material and labour for Earthing complete with GI earth plate electrode 600 x 600 x 6 mm thick burried directly in ground (earth pit not less than 2.5 m deep below ground level) with top edge of plate not less than 1.5 m below normal ground level, earth pit surrounded by 15 cm thick and packed layers of charcoal, dust and common salt, including GI wire 4 mm dia as earth lead fixed by means of nuts, bolts, check nuts and washers etc and other end connected to the test point including 15 mm dia light grade GI protection pipe and watering pipe 20 mm dia medium grade with funnel and wire mess including necessary earth work, PCC earth pit chamber in PCC 1:2:4 using 20 mm graded stone aggregate with precast RCC pit cover 80 mm thick etc all as shown in Electrical Plate No. 3 of SSR Part 1, complete all as directed and specified.

Note : Schedule of credit for Rs. 1,22,052.80 to be deducted on acceptance of bid.

M/s Aman Enterprises (BID ID -3087208)

M/S KAMLA CONSTRUCTION CO. (BID ID -3084864)