Construction of Marriage Hall in Temple Vacant land in Arulmigu Thirumalaikumaraswamy Thirukoil at Panpozhi Shenkottai Taluk Tenkasi District

Amount

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except to rock requiring blasting but including shoring strutting and bailing out water wherever necessary and refilling the sides of foundation with excavated earth in layers of not more than 15cm thick well consolidated and depositing the surplus earth within the compound with an initial lead of 10 metres and lift of 2 metres in places as shown by the departmental officers and clearing levelling the site etc complete complying with standard specification.

Cement Concrete 1:4:8 (One Cement, Four CS sand and Eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification.

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Supplying and filling in foundation and basement with Gravel in layers of not more than 15cm thick well rammed watered and consolidated etc.,

R.R.Masonry in Cement mortar 1 : 5 (One cement and five scs sand for Foundation and Basement above ground level pointing with cement morter neatly finished and curing etc. complete complying with standard specification

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton.

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as rectangular or square RCC columns

For Circular RCC columns, , etc.

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers..

Providing and laying in position, standardised concrete Mix M20 grade in accordance with IS 456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of work with minimum cement content of 325 Kg/m3 and maximum water cement ratio of 0.55 including admixyure (Plasticiser / super plasticiser ) in recommended proportions as per : 9103 to accelerate retard setting of concrete, improve workability without impairing strength and durability with about (5Cum) 7730kg. og 0mm machine crushed stone jelly and with about (3.3cu.m.) 5156kg. of 10-12 mm machine crushed stone jelly with about 4.79Cu.m. )7670kg. of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering and also including laying , vabricating with mechical vibrators, finishing curing etc., and providing fixtures like fan clamps in the RCC floor/ roof slab where ever necessary without claiming extra ,etc., complete.complying with standarde specification and as directed by departmental officers.The coarse and fine aggregates to be used should compling with the requirements of IS Standards. ( No separete payment will be made by the department for excess usage of materials)

Foundation and Basement

Ground floor

First Floor

Second Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Cement Concrete 1:3:6 (One Cement, Three CS sand and Six broken stone jelly) using 40mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. (Reinforced Cement Concrete 1:2:4 for slab to be extended upto top of splashing with pressed tiles and future extension rods to be embedded in CC 1:3:6 (One Cement, Three Sand and Six hard broken stone jelly). Dummy columns should be at least 1 metre height)

Brick work in following Cement Mortar 1:5 (One cement Five CS sand ) using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-1/4" for foundation and basement including curing, etc., complete complying with standard specifiction..

Foundation and basement

Superstructure in GF

Brick work in following Cement Mortar 1:6 (One cement six CS sand ) using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-1/4" for foundation and basement including curing, etc., complete complying with standard specifiction.

Super structure in ground floor

Super structure in First floor

Super structure in second floor

Brick partition walls of 10.80cm thickness using best quality country bricks of size 8-3/4" x 4-1/4" x 2-3/4" in Cement Mortar 1:3 (One Cement and Three CS Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Foundation and basement

Ground floor

First floor

Supplying nad fixing terra kotta jally 20x20x0.75mm including cost of materials nad labour charges cement mortat etc., complete as directed by departmental officer

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three CS Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five CS sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:3 (One Cement and Three CS Sand) 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Paving the flooring with high quality specail coloured and Double charged Virtified tiles of approved quality and brand of size 600mmX600mmx8mm thick for flooring of approved quality and colour set in cm1:3 (one cement an d three sand ) 20mm thick and pointing with white cement using at the rate of 0.40Kg/m2 including finishing the joint neatly ,pointing flush with tiles surface etc,complete complying with standard specification and as directed by the departmental officer.

Flooring with anti skid ceramic colour and design tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three CS Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification.

Flooring with Joint free rectified Ceramic Tiles of size 3O5 x 3O5 x 8mm laid over 20mm thick cement mortar 1:3 (One cement and Three CS sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in positionand and pointing with white cement mixed with colouring pigment at the rate of 0.3 kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be Johnson / Kajaria / Somany / Nitco / RAK or Equivalent which has to be got approved by Executive Engineer before use on works)

Dadooing walls with best approved quality, design colour glazed tiles of size 300mm x 450mm x 8mm set in Cement Mortar 1:2 (One Cement and Two CS sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Paving the floor with pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers.

Solid PVC Door Shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter

Supply and fixing Teak wood frame for door and windows ventilator wrought and putup including cost of matrerials and labour charges etc., complete as directed by departmental officer

Supply and fixing CRCA Pressed Steel Box Section 18 Gauge or 1.25mm thick for Door Frames including providing holes and fixing wooden blocks for fixing furniture and fittings etc., complete

Supplyand fixing Teak wood fully panelled shutters upto 4m Length and Teak wood 50mm thick for styles and 22mm thick for Planks including labour charges, fitting etc., complete as directed by departmental officer

Supplyand fixing UPVC windows of outer frame 60x58mm 100% corrosion free wall thick 2mm with multi power point locks with colour glass 4mm thick with hinges, locking system and got approved from EE wrought and putup including cost of matrerials and labour charges etc., complete as directed by departmental officer

Supply and fixing mild steel grills for windows, ventilator, gate, ladder etc including priming coat.including cost of matrerials and labour charges etc., complete as directed by departmental officer

Solid Core Flush Shutters with teakply on one side and commercial ply on other side with teak wook lipping alround 35mm thick (Double Leaf)

Solid Core Flush Shutters with teakply on one side and commercial ply on other side with teak wook lipping alround 35mm thick (Single Leaf)

Supplyand fixing UPVC louvered ventilator 60x58mm frame with glass panels ,wrought and putup including cost of matrerials and labour charges etc., complete as directed by departmental officer with 60x78mm shutter pin headed glass 4mm thick and got approved from Executive Engineer

Supplying and fixing of PVC Sliding Door with Roller The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the one coat of zinc chromite priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three CS Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing in position best approved of ISI quality of PVC rain water down fall pipes having a pressure of 4 Kg./sq.cm including cost of necessry PVC shoe, PVC bend, gratings of required diameter and special clamps, brass screws, nails, etc. and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc. complete. The rate shall be inclusive of cast of removable iron grating. The PVC pipe shall be fixed in wall with special type of clamps. Special type of "U" clamp at the centre of the pipe line shall be fixed in addition to those for more than 3.0 M pipe length complying with standard specification. 160mm dia PVC rain water down fall pipes

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification.

Supplying and fixing in position CP shower rose with CP stop cock arrangement of size 15mm dia inlet and 100mm outlet to the pipe line with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications.

Supplying & fixing inposition 15mm dia Chromium Plated brass screw down tap (heavy type) of approved make confirming to ISS and including cost of shellac, thread etc., complying with standard specification and including cutting and threading wherever necessary etc., complete complying with standard specifications.

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm White glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two CS sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing PVC ventilating shaft of 100mm dia with 3 metre height including cost of 100mm dia AC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers

Supply and fixing in poistion CI Manhole covers with CI Frames (Heavy Duty) of size 60 cm x 60 cm as directed by departmental officers.

Supply and fixing in position best quality PVC Soil/ waste pipes 6 kg / sqcm of various size (Above Ground Level) having ISI mark and providing leak proof joints including fixing to the wall with special PVC /MS clamps, etc., and making connection to all sanitory fittings, dismantling masontry / RCC works wherever necessary and making good the dismantled portion to the original condition, complying with standard specification etc., complete.

110mm dia

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

110 mm PVC Elbow

110 mm PVC Door Elbow

Supplying, laying and joining UPVC pipes of approved quality and best veriety conforming to ISS with ISI mark, of the the following size above Ground level up to 4 M hight laid properly to alignment including cutting, threading and fixing the required UPVC specials but excluding the cost of such specials and fixing to the wall with necessary TW plugs, clamps and screws, making holes on the wall or drilling holes in the roof and making good dismantled portion to original condition with necessary brick work, concrete and plastering wherever necessary with necessary scaffolding charges etc., complete.

32mm dia Upvc pipe

25mm dia UPVC pipe

Supplying and fixing in position UPVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the UPVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The UPVC specials should be got approved by the Executive Engineer before use on works).

32 mm dia elbow

32 mm dia TEE

32 mm x 25mm reducer

25 mm x 20mm reducer

20 mm x 15mm reducer

20 mm dia Elbow

20 mm dia Tee

Supplying and fixing in position first quality and approved variety Gun Metal Gate valve (Heavy type)/ Wheel Valve (Heavy Duty) with ISI Mark of approved quality of the following dia including cost of shellac, thread, labour charges for cutting, threading,fixing in position etc., for both internel and external water supply arrangements. 25mm dia Gate valve

32 mm dia Gate valve

32 mm dia Wheel Valve

Supplying and fixing position CI/PVC Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three CS sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)Nahani Trap of size 100 x 75mm with stainless steel gratings

Supply ami Fixing PVC water lank of 1000 Lit including cost of all materials and labour charges etc., complete

Drilling of Borewells anywhere in Tamilnadu including transportation from one place to another with in Tamilnadu in alluvial soil sedimentary strata of clay and sand stone shale pebbles boulders etc. By first taking a pilot bore of 140 mm/150mm dia and then enlarging to required dia direct or reverse rotary mud circulation method using rotary rigs, fuel, labour and drilling bentonite and water required for drilling at site ( Site will be shown by the Dept Officers) including construction of mud pit.

Depth 0 to 60m

Above 60m to 90m

Above 90m to 120m

Above 120m to 150m

Above 150m to 180m

Above 180m to 200m

Supplying and fixing of 150mm dia CS PVC casing pipe assembly with slota (or) with out slots in the driilled hole including welding the joints etc complete and supplying and packing the annular space with pebbles of size and quality as approved by the departmental officers etc complete

Supply and fixing of 5.00 HP Submersible pump including Labour charges for errection of Submersible pumpset in borewell all acessories vost and conveyance etc., complete as directed by departmental officer

Supplying and fixing of 3 phase electrical panel Board D.O.L with two level guard and auto start including cost and coveyance and fixing charges etc complete. as directed by departmental officer

Supplying and fixing of 4 core 6 PVC armoured UG cable including cost and conveyance and labour charges etc complete. as directed by departmental officer

Supplying and fixing of HDPE pipe 32mm dia HDPE pipes for 3 HP Submersible pumpset including cost and conveyance of all materials and all labour charges etc complete. as directed by departmental officer

Supply of Suitable dia PVC Nylon rope for submersible motor as directed by departmental officer

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supplying and fixing of fine Cuddapah slab of 38 / 40 mm thick for Cup - board arrangements in brick wall including levelling to correct alignment etc complete complying with standard specification and as directed by departmental officers

Providing cupboard shelf shutter using 19 mm thick water proof plywood shutter with country wood frame 12 x 5 cm size both vertical and horizontal frame .The edges of plywood shutter should be fixed with 25 x 12mm size teak wood beading .The MS piano hinges 2 Nos each 30 cm long should be fixed in each shelf .3 strip magnetic catcher 4 nos ,100 mm long handle 'D'type 2 nos ,50mm size door lock 1 no ,125 mm long brass pat lock 1 no should be fixed in each shelf .After the completion of the cupboard shutter the plywood areas both inside and outer side and country wood frame areas should be painted with two coats of enamel painting .The rates inclusive of nails ,fevicols,screws etc., complete.

Dry Brick work using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-1/4" for foundation and basement including etc., complete complying with standard specifiction.

Supplying and filling using 20mm gauge hand broken granite stone jelly for foundation and basement including dewatering if found necessary and laid of not more than 15cm thick and compacted. etc. complete complying with standard specifications

Supplying and filling using 40mm gauge hand broken granite stone jelly for foundation and basement including dewatering if found necessary and laid of not more than 15cm thick and compacted. etc. complete complying with standard specifications

Manufacturing and fixing in position of RCC Precast slab CC 1:2:4 - 50mm Thick using 20mm 'size of hard broken granite stone for all RCC works using machine for mixing concrete excluding cost of steel, fabrication of reinforcement, centering, strutting and shuttering and placing the grills in position etc., complete complying with standard specification

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings..... such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum- Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact.

Supplying and fixing 4 Nos. Fire Buckets made out of 40 x 40 x 6mm MS Angle etc., complete as directed by departmental officer (P 207)

Supplying and fixing Fire Extinguisher Co2, 4.5 kg. confirming to TAC Normsetc., complete as directed by departmental officer (P 207)

Supplying and Fixing of Aluminium Dye Cast Letters of approved size and colour. The colour treatment process is achieved with MRF colour coat and then the processed coloured layer is set into the kiln for the heat treatment process for the size Aluminium Dye Cast Letters 9’’ size the following letters பண்பொழி அருள்மிகு திருமலைக்குமாரசுவாமி திருக்கோவில் திருமண மண்டபம்

Supplying and filling using 10.12 mm gauge hand broken granite stone jelly for foundation and basement including dewatering if found necessary and laid of not more than 15cm thick and compacted. etc. complete complying with standard specifications

Plain Cement Concrete 1:3:6 (one cement, Three CS sand and six hard broken stone jelly) using 20mm jelly for for foundation including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

Supplying and filling foundation and basement with conveyed earth in layer of not more than 15cm thick well rammed watered and consolidated etc., complete

Supplying and filling Interlocking Paver block stone 83 mm thick over a base layer of crushed stone sand filling inclu. Cost of materials etc., complete

Electrical Work

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection by 1.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End (SD - 281)

Wiring with 3 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point Higher End (SD - 298)

Supply and fixing of single box type 4'20W LED fitting with TW round blocks on wall or ceiling with with PVC unsheathed copper leads from terminals to the fitting (LED fittings should be of Higherend company make like philips / cromption etc) Higher End (Data -1)

Supply and fixing of 4'20W LED fitting complete with 1.5 mt conduit pipe suspension from the ceiling PVC unsheathed copper leads from terminals to the fitting Higher End (Data-2)

Supply and fixing of 4'20W LED fitting complete with 2 mt conduit pipe suspension from the ceiling PVC unsheathed copper leads from terminals to the fitting Higher End (Data-3)

Supply and fixing of Havells jeta alba flood light 100W LED fitting with necessary wall grouting clamps with fixing bolts on the ceiling with PVC unsheathed copper leads from terminal to the fitting Higher End (Data-4)

Supply and fixing of fancy lamp Fitting with 9W LED bulb on wall connection (Data-5)

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting (SD - 535)

Supply and fixing of 1200mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 300mm down rod on the existing clamp (SD - 110)

Supply and fixing of 1200mm (48") AC ceiling fan complete with stepped electronic 300W regulator with 1 meter down rod on the existing clamp (SD - 107)

Supply and fixing of 750mm (30") sweep AC wall Mounting air circulator with suitable clamps and connection (DATA - 6)

Supply and fixing of 450mm (18") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall (SD - 118)

Supply and fixing of louvers shutters arrangements for 450mm (18") sweep light duty AC Exhaust fan (SD - 123)

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall(SD - 114)

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan (SD 120)

Supply and fixing of 4KVA stabiliser of cut off range (190V-270V) (Make V-Guard) (Data-7) SOR- M 1988

Supply, installation, testing and Commisioning of 1.5 ton split type air conditioner with copper tubes for outdoor unit and stand Make O- General/ Daiken)(Data-8)

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End (SD 464)

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End (SD-401)

Supply and fixing of 20A DP MCB Switch in suitable 2 pole sheet steel enclosure with earth connection (Data-9)

Supply and fixing of 40A DP MCB Switch in suitable 2 pole sheet steel enclosure with earth connection (Data-10)

Supply and fixing of 32A TP MCB Switch in suitable 4 pole sheet steel enclosure with earth connection (Data-11)

Supply and fixing of 100 A Three phase 500V 4 Pole Change over Switch in suitable angle iron frame work with MS cable entry boxes with earth connection only.(SD-736)

Supply and fixing of 100A MCCB Switch in suitable 4 pole sheet steel enclosure with earth connection (Data-12)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End.(SD-520)

Supply and fixing of 8 way Horizontal Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 24 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End.(SD-501)

Supply and fixing of 4 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB Incomer ) with double door (metal door ) with 1 no. 100 A 4 P MCCB switch as incoming and 2 nos. 63A 3P MCB , 6 nos. 6A to 32A SP MCB as outgoing with suitable cable end box on wall with earth connection only. Higher End.(Data-13)

Supply and Run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour.(SD-337)

Supply and Run of 2 of 4 sq.mm. (56/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 6 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour.(SD-430)

Supply and Run of 2 of 6 sq.mm. (84/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection by 6 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour.(SD-353)

Supply and Run of 4 of 10 sq.mm. (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 10 sq.mm. PVC insulated SC unsheathed copper wire with painting of suitable colour (SD- 347)

Supply and Run of 4 of 16 sqmm (101/0.45) PVC insulated Single Core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed on wall and ceiling with continuous earth wire connection of 1 of 40 sq.mm (50/0.3) PVC copper wire with suitable colour (Data-13)

Supply and Clamping of 3-1/2 x 95 sq.mm. PVC LTUG armoured cable on post or wall MS Clamps (SD-226)

Supply and fixing of brass cable gland for 3-1/2 x 95 sq.mm. PVC armoured LTUG cable with earth connection (SD-190)

Supply and fixng of TNEB meter board suitable for 3 phase 100A service connection made up of suitable angle iron frame work of size 2 feet x 1-1/2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1-1/2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 100A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with earth connection complete (SD-130)

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with necessary clamps to hold the LTUG aluminium Service cable with painting of suitable colour (DATA - 14)

Supply and run of 1 of No.8 SWG. PVC copper on suitable PVC rigid pipe on wall with painting of suitable colour for Earth Connection (DATA - 15)

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry(SD-233)

S.Selvaraj (BID ID -1205875)