SOPD_SIG_19_20_88

Amount

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300mm dia, removal of stumps of trees cut earlier and disposal of serviceable materials to be used or auctioned, upto 1000m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specifications Clause 201. (I) By Mannual Means B. In area of thorny jungle

Scarifying existing bituminous surface to a depth of 50 mm by mechanicalmeans (Scarifying the existing bituminous road surface to a depth of 50 mm and disposal of scarified material with in all lifts and lead upto 1000 metres

Dressing & profiling the existing WBM/Granular surface layer of the road from edge to edge of the existing carriage way, filling low spots and ravelled stretches by providing additional materials of same type as that of the existing top surface layer, cambering, watering, rolling with 8-10 tonne roller to obtain specified compaction, etc to obtain a uniform formation surface with cross fall from the road centre line to the outer edges of the existing embankment. Works to be carried out in accordance with MORT&H specifivation section 300 and as directed by the deptt. (rate considered as per SOR for road bridge and culvert works for all divisions inder PWD Assam 2009-10, at sections where the top level of the subgrade of the existing road surface is not proposed to be raised by more than 100mm. I) Roads having hard crust

Embankment Construction with Material Obtained from Borrow Pits (Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirment of table 300-2 ( including compensation of earth.)( Including cost of testing of materials at site and laboratory as directed by the deptt.) (a) From private land

Construction of Subgrade and Earthen shoulders with approved materials obtained from borrowpits, with all leads and lifts, transporting to site, spreading, grading to required slope and compacting to meet requirement of Table 300-2 (including land compensation of earth) as per drawing and Technical Specifications Clause 305.

Wet Mix Macadam (Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sb-base/base course on well prepared surface and compacting with vibratory roller to achieve the desired density

Prime coat Prime coat (Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 1.00 kg/sqm using mechanical means.)( Including cost of testing of materials at site and laboratory as directed by the deptt.) A. with bitumen emalsion-CSS- 1h

Tack Coat :- Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20kg per sqm on the prepared bituminous/ grannula surface cleaned with mechanical broom ( Including cost of testing of materials at site and laboratory as directed by the Deptt.) ii) With bitumen emulsion- CSS-1 (IS- 8887-2004 ) (b) dry & hungry bituminous surface

Dense Graded Bituminous Macadam (Providing and laying dense bituminous macadam with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixedwith bituminous binder@ 4.0 to 4.5% by weight of total mix and filler transporting the hot miox to work site,laying with a hydrostatic paver finisher with sensor control to the reqd. grade, lavel and alignment,rolling with smooth wheeled,vibratory and tandem rollers to achieve the desired compaction as per MoSRT&H cl. no. 507. complete in all respect. (As per analysys-3) ( Including cost of testing of materials at site and laboratoryas directed by the deptt.) ( Including extra lead beyond 5.00 km for carriage of materials from quarry toplant site and exrtra lead beyond 10.00Km from Plant site to Laying site.) (a)'with VG-30 grade bitumen (ii) for grading-II )19mm nominal size)

Bituminous Concrete (Providing and laying bituminous concrete with 100-120 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder@ 5.4 to 5.6 % of mix and filler transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the reqd. grade, lavel andalignment, rollingwith smooth wheeled,vibratoryand tandem rollers to achieve the desired compaction as per MoSRT&H cl. no.509. complete in all respect. (as per analysys-3 ( Including cost of testing of materials at site and laboratory as directed by the deptt. )( Including extra lead beyond 5.00 km for carriage of materials from quarry to plant site and exrtra lead beyond 10.00Km from Plant site to Laying site.) (a)'with 60/70 or VG-30 grade bitumen (ii) for grading-II )13mm nominal size)

Retro reflectorised Traffic sign: Providing and erecting of Retro-Reflectrorised cautionary, mandatory & informatory sign as per IRC: 67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly design foundation with M-15 grade Cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing and sign. ( All the Steel work must be Tata/Sail/or any other approved brand) (i) 60cm equilateral traingle

Retro reflectorised Traffic sign: Providing and erecting of Retro-Reflectrorised cautionary, mandatory & informatory sign as per IRC: 67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly design foundation with M-15 grade Cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing and sign. ( All the Steel work must be Tata/Sail/or any other approved brand) (ii) 60cm circular

Providing reflective pavement marker with a provision of spike at the bottom with Micro prismatic lens in both direction having thermoplastic body adhering to the specification and guidelines of MoSRTH & H's fixed to the road surface using the adhesives and the procedures recommended by the manufacturers with three months replacement warranty and free maintenance.

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.

Providing and laying Hump Type Speed Breaker as directed by department

Planting of Trees and their Maintenance for one Year (Planting of trees by the road side (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge mannure, planting the saplings, backfilling the trenches, watering , fixing the tree guatrd and maintaining the plants for one year.

E/Work in excavation for structures as per drawing and technical specification, clause 305-1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m., dressing sides and bottom and backfilling in trenches with excavated suitable material. 1. Ordinary soil (i) Upto 3.0 m. depth

Providing concrete for plain/reinforced concrete in open foundations complete as per drawing and technical specification Clause 802, 803, 1202 & 1203. A. With Crushed stone. I. PCC grade M15

Plain/reinforced cement concrete in Sub Structure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204. A. With Crushed Stone I. P.C.C grade M 15 I. Nominal mix (1:2.5:5)

Furnishing and Placing Reinforced/Prestressed cement concrete in super-structure as per drawing and Technical Specification' including steel shuttering formwork. A. With crushed stone I. RCC grade M 20 (iii) For design mix RCC M20 a) Height upto 5.0 m.

Providing and laying cement concrete wearing course M30 grade including reinforcement complete as per drawing and Technical Specification Clause 800 and 1206.3. A. With crushed stone

Providing weep wholes in brick masonry/ stone masonry, plain/ reinforced concrete abutment, wing wall, return wall with 100mm dia AC pipe extending through the full width of the structures with slope of 1(V) : 20(H) towards drawing face complete as per drawing and Technical Specification Clause 614, 709, 1204.3.7.

Drainage spouts complete as per drawing and Technical Specification Clause 1209.

Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification Clause 1204.3.8

Supplying, fitting and placing TMT bar reinforcement (Fe 500) in sub structure complete as per drawing and Technical Specification Clauses 1002, 1005, 1010 & 1202.

Sri Dhiraj Borgoyary