Providing Basic tourist infrastructure in Therku Kallikulam at Tirunelveli District .

Amount

Clearing the Heavy Jungle by deploying JCB and the same stacked away from the work spot for disposal. The rate inclusive of Hire charges for machinary, fuel and driver betta, etc., complete.

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. Rate to include backfilling, leveling, dressing of sides and ramming of bottom with all leads, lifts and filling inside the building plinth level including necessary compaction in layers of 150mm thick each complete as directed by the departmental officers. Note: The cost of earth work excavation shall be calculated based on the classifications of soils furnished in the trial pit details appended with the estimates.For 0 to 2m depth.

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification. Rate to include backfilling, leveling, dressing of sides and ramming of bottom with all leads, lifts and filling inside the building plinth level including necessary compaction in layers of 150mm thick each complete as directed by the departmental officers. Note: The cost of earth work excavation shall be calculated based on the classifications of soils furnished in the trial pit details appended with the estimates For 2 to 3m depth.

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification. 0 to 2m depth.

Supplying and filling in foundation, basement, etc with following Manufactured sand brought from outside filling materials in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc with following Good Earth brought from outside materials in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Suppply and Filling in foundation with 'M' sand in suitable thick layers well rammed and consolidated including watering complying with standard specifications

Providing Pre - construction Anti - termite treatment and creating a chemical barrier to the building by injecting chemical emulsion of required concentration under grade slab and grade beam and below the ground level as well as outside all-round the building at plinth level etc as per the instructions of manufacturer and as directed by the Client / departmental officers. The treatment shall be carried out strictly in accordance with the technical specification and conforming to IS 6313 or equivalent BS specification. The chemical to be used as insecticide for the treatment shall be Biflex Tc and the application shall be diluted 1 part of chemical Biflex Tc with 49 parts of water to get 0.05% emulsion and strictly in accordance with the manufacturer’s specification. The work should be carried out by an approved and registered specialist pest control agency only. Tenderer to furnish the name of the proposed specialist firm. A 10 years post application guarantee against defects shall be furnished by the main Contractor. Note : Horizontal plan area at ground floor level of the building will be measured and paid. The chemical to be used for the treatment and concentration of the chemical solutions should be as laid down in IS - 6313 Part II.as complete with all respects complying with relevant standard specification, as directed by the Client / departmental officers.

Cement Concrete 1:4:8 (One Cement, Four Manufactured sand and eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification

Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid) Cost of MS sheet and angles for each set weight of MS sheet BG 10 of size 90cm x 60cm x 3.175mm 3.175 x 7850/1000 = 24.92 Kg,24.92 Kg x 0.54 Sq.Mt = 13.46 Kg,Weight of MS angle of size 25mm x 25cm x 3mm 3.6 x 1.1Kg/Mt = 4.00 Kg.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such ascolumn footings, column pedestals, plinth beams, grade beams,staircase steps, etc.., requiring nominal strutting using mildsteel sheets of size 90cm x 60cm and 10 BG stiffened with weldedmild steel angles of size 25mm x 25mm x 3 mm for boarding, laidover silver oak joists of size 10cm x 6.5cm spaced at about 75cmcentre to centre or at suitable intervals etc. complete in all floorscomplying with standard specifcation.

Reinforced cement concrete Column footing, plinth / grade beam, bed blocks, template surfaces, steps, piers, pile cap, raft slab / beams and such other members

Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slab / beams and such other members

For plane surfaces such as rectangular, square columns and chamfered sunshades, top and bottom slab of boxing, kitchen platform, loft and such other structural members

Vertical surfaces - For all type of walls (any thickness) including, retaining wall, core walls, shear wall, parapet wall, fins, facia, kerb and median etc... for all floors & levels.

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.0 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kg/mᶾ and maximum water cement ratio of 0.50, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of Manufactured sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation and Basement

Ground Floor

1st Floor

Terrace Floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of 100mm thick, Precast slab in RCC 1:2:4 (one cement, two Manufactured sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed.

Brick work in following Cement Mortar 1:5 using best quality of Second Class Ground Moulded Chamber Burnt Bricks 9" x 4-3/8" x 2-3/4" in Cement Mortar 1:5 (One Cement and Five Manufactured Sand) for foundation and basement and for superstructure including curing, etc., complete complying with standard specifiction.

For foundation & basement

Ground Floor

1st Floor

Terrace Floor - 1

Brick partition walls of 11.50cm thickness using best quality II Class Ground Moulded Chamber Burnt Bricks of size 9" x 4-3/8" x 2-3/4" in Cement Mortar 1:3 (One Cement and Three Manufactured Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Ground Floor

1st Floor

Supplying and fixing Teak Wood Frames for Doors, Windows, Ventilators and other similar joinery works with the following sizes and sections including labour charges for wrought and put up in position and also for fixing hold fast in frames and masonry etc complete in all floors. Teak Wood Scantling upto 2m length

Supplying and fixing Teak Wood Frames for Doors, Windows, Ventilators and other similar joinery works with the following sizes and sections including labour charges for wrought and put up in position and also for fixing hold fast in frames and masonry etc complete in all floors. Teak Wood Scantling over 2.0m and below 3.0m in Length

Supplying and fixing of 200mm length mild steel hold fasts horizontally twisted with pair of suitable iron screwsetc complete in all respects complying with relevant standard specification and as directed by the Departmental officers.

Providing and fixing Single Leaf Solid core flush shutters with Teak ply on both side with teak wood lipping alround 35 mm thick. The shutter shall be made of solid core of block board type bonded with PF synthetic resin conforming to BWP grade of IS 848 with 6mm thick teak wood lipping as per drawing. The construction procedure of the shutter should be as per IS 2202. The shutter shall be shop prepared for taking mortice lock or latches suitable lock block of wood may be provided for fixing the hardware. The size of block, shall perfectly correspond to the maximum size of lock, covered in IS 2209. All the four edges of the door shutter shall be square. The shutter shall be free from twist or warp in its plane and of required size etc. complete as directed. The both side door shall be finished with 1mm thick laminate of approved color and pattern. Rate shall include for cost of hardwares (aluminium hinges 125x30mm size - 4 / 3Nos. aluminium aldrop of size - 250x16 mm - 1No. Aluminium tower bolt of size 250x12mm - 1Nos. tower bolt of size 200x12mm - 1No, D type aluminium handle of size 200mm-2No., aluminium door stopper with nylon bush - 1No) as required and fixing them all like lock, hinges, handle, tower bolts, and other accesories etc..as complete with all respects complying with relevant standard specification, as directed by the Departmental officers.

Foamed PVC Door Frame Providing of Factory made prelaminated FPVC (Foamed Polyvinyl Chloride) Door frame of the size 105x40mm with a wall thickness of 10mm made out of extruded rigid FPVC profile mitre joined with 6 Nos. of 50mm long screw. The door frame shall be fixed to the wall by using 80mm long screws through the frame with the help of PVC fasteners of 3 no's to be provided for each vertical member,GIstiffners of ("U" chanel of size 29x9x1mm, 150mm long) -3 no's at hinge point, Frame reinforcement of ("U" GI chanel of size 46x22x.06mm), Bottom tie rod of ("U" GI chanel size of 15x15x1mm) etc. complete as per manufacturers specification for finished item of work. The door frame should be got approved from the Executive Engineer before use on work

ABS DOOR / EQUIVALENT Providing of 35mm thick Facotry made Prelaminated ABS (AcrolynitrileButadyne Styrene) Door shutter moulded in different designs, consisting of all round Frame made out of water proof solid foam PVC bar of size 20x32mm, reinforced by 32x 32mm - 2 nos. for vertical made out of LVL (Laminated Veneer Lumber), core material of 32 mm thick high density craft paper honey comb board, sandwiched on both sides with prelaminated ABS sheet thickness of 1.5mm. PVC edge banding of size 0.45mm on the vertical sides. Hardware made out of steel coated butterfly hinges-3 nos for each shutter,aluminium aldrop of size - 250x16 mm - 1No. Aluminium tower bolt of size 250x12mm - 1Nos. tower / side bolt of size 200x12mm - 1No, 'D' SS pull handle 200 mm on both sides, with ISI make complete for finished item of work, complete complying with the standard specification. The door shutter and frame should be got approved from the Executive Engineer before use on work. 750 X 2100 mm

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Providing and fixing welded M.S. grills for the window openings and any openings as per drawing with necessary screws, bolts and fixed with necessary M.S. lugs embedded in masonry with C.C. 1:2:4 and finishing the surface neatly. Design of grills and the size of members to be used shall be got approval before put into use & as directed by the departmental officers.

Paving the floor / skirting with best quality Double charged vitrified tiles of Size of tiles shall be 800 X 800 X 10 mm Double charged vitrified tiles- Polished / Matt approved colour, shade and quality laid in cement mortar 1:3 (one cement and three Manufactured sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Manufactured Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the wash basin counter with best approved quality fine polished Granite Stone Slabs 18 / 20mm thick of Jet Black with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three Manufactured sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor / skirting with best approved quality Flamed finish Granite Stone Slabs of size 1200 x 600 of 16 / 18mm thick of Ruby Red, Raw silk and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three Manufactured sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Extra for pre finished Double nosing to treads of steps / counter slab of Granite stone

Extra for Grooving the Granite slab of steps

Dadooing walls with Size of Tile - 300 x 600mm x 10mm following best approved quality, polished Ceramic tile of following sizes set in Cement Mortar 1:3 (One Cement and Two plastering sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Plastering with Cement Mortar 1:5 (One cement and Five plastering sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three plastering Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Supplying and painting the walls and ceiling with two coats of cement paint over one coat of cement primer as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The colour and shade of the cement paint shall be got approved by the Executive Engineer before use of work).

Supplying and painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The wall putty shall be got approved by the Executive Engineer before use of work).

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat of over cement plastered wall surface ect., complete complying with standard specification.

Providing and applying Texture paint finish for exterior / interior surface as per Manufacturers specification and as directed. Application of primer by diluting the texture compound by mineral on the plastered surface and apply final two coats of exterior / interior emulsion on the primer. Rate including all brush, ladder, scrapping, washing, materials, labour charges, wastages, cleaning, necessary lead and lifts, scaffolding, stagging, working at all levels, elevations, transportaion charges, loading, unloading, curing, sanding, touchup putty, surface thoroughly cleaned and wetted before painting as complete with all respects complying with relevant standard specification and as directed by the departmental officers.

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades, Structural steel members etc., with two coats of best approved first quality and colour of synthetic enamel paint over one coat of red oxide priming coat in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Underground structures waterproofing with HDPE membrane Providing and laying water proofing treatment to the Rafts, Below grade slab, Lift pits, water retaining structures with fully bonded 1.5 mm thick HDPE waterproofing pressure sensitive adhesive membrane over PCC before laying raft concrete having higher puncture resistance of 1000N as per ASTM E 154, confirming to BS 8102 & IS 16471:2017, requirements of UG waterproofing structures. Laying adjacent sheets by keeping overlap of 75mm, end overlaps to be treated using double sided tape. The membrane shall have Tensile strength >25 Mpa as per ASTM D 412, Elongation > 500% as per ASTM D 412, Hydrostatic head resistance >70m head of water as per ASTM D 5385, Low Temperature Flexibility: -25 deg C, Peel Adhesion to Concrete >880 N/m as per ASTM D 903 Modified, UV Exposure > 45 Days. The finished cost including surface preparation completely as per specification.

Retaining wall/ UG tank wall (outside) Waterproofing with SBS Membrane Providing and laying water proofing treatment to the Retaining wall, water retaining structures outside with fully bonded 1.6mm Thick SBS modified self-adhesive, cross laminated HDPE lining waterproofing membrane, conforming to IS 16471:2017 Type A, requirements of UG waterproofing structures, The SBS membrane shall have Mass per Unit Area > 1.8 Kg/m2 as per ASTM D 5147, Puncture resistance > 200 N as per ASTM E 154, Elongation > 180% as per ASTM D 412-06, Tensile Strength > 4 Mpa as per ASTM D 412- 06, Tear resistance > 20 N/mm as per ASTM D 4073, Hydrostatic pressure > 50M as per DIN 1048. The lap with HDPE membrane shall be 100mm treated with TS tape. followed by the installation of 8-10mm THK polyethylene dimpled drain board having compressive strength > 400kN/m2 (as per ISO 25619-2). The finished cost includes surface preparation, making coving and a coat of solvent based bituminous primer @ 0.25l/m2 on entire surface before laying membrane completely as per specification.

Newly Constructed Roof/Bathroom/Toilet/ balcony /utility with Cementatius Waterproof coating Providing and Applying CFTRI approved two component flexible polymer modified acrylic cementitious waterproofing coating with a mix ratio of (5 Liquid :7 Powder) to the RCC surface like Roof, bathroom, toilet, balcony & utility area applied @ 2.2kg/m2 in 2 coats to achieve 1.2mm DFT, having Elongation at break >120% as per ASTM D 412, Tensile strength >1N/ mm2 as per ASTM D 412, Adhesion strength: 0.80N/mm2 as per ASTM D 4541, crack bridging upto 2mm as per ASTM C 836. The finished cost to include surface preparation, making coving of 50 mm X 50mm at all right angles of wall Junction with Polymer Repair Mortar and lay 45 gsm glass fibre mesh over the angle fillet when the first coat in still wet, treatment of cracks completely as per specification.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Paving the Top of roof with Solar refelective ceramic tiles of size 305 x 305 x 7mm thick of approved quality and colour laid in Cement mortar 1:3 (One cement and three crushed stone sand) 12mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint, curing etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Providing and laying in position the RCC humepipes of approved quality and make including collars,. necessary Excavation, PCC 1:2:4 supports, Manufactured Sand cushion of 150mm on all sides, Refilling with earth, Compaction and making good the level, alignment etc.,complete as directed by the departmental officers. 300mm dia NP3 class Hume pipe

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Designing, Providing and fixing in position Hot rolled structural steel Members / Sections consists of MS joists, channels, angles, purlins, pipes, hollow tubes, runners, insert plates, flats, gate for compound wall etc. at all levels. Rate to including all materials, labour charges, scaffolding, stagging, transportation, lead & Lifts, wastage, cost of bolts, nuts, washers, welding, electrodes and connections required for the work etc., as complete with all respects complying with relevant standard specification, as directed by the departmental officers.

Supply and Filling of 20mm brick jelly as shown in drawing. Rate to include all material, labour, lead and lifts etc, complete.

Supply and installation of wooden cot to the shape, size and profile as shown in the Architectural drawing, with the details listed below. Wooden legs are finished with melamine polish and the wooden ply are finished with 1mm laminate of approved colour and shade as directed by the departmental officers. (Size of the cot (0.90 x 1.83m )

Supply of Single mattres with with high density PU foam.

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting

Supplying and fixing Wash Hand Basin of size 550 x 400mm with all accessories such as cast Iron Brackets, 32 mm Dia C.P. Waste coupling, Rubber plug and Chain, 32 mm dia ' B ' Class G.I. Waste pipe, 15 mm Dia G.M Wheel valve; 15 mm Dia Nylon connection, 15 mm Dia Brass Nipples, 15 mm C.P. Pillar tap etc.,including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and as directed by the Department officers. (The Wash basin should be got approved by the Executive Engineer before use on works.

Supplying and fixing of CP Two Way Bib Cock with Health Faucet ,wall hook & one metre long flexible tube including cutting and making good the walls wherever required etc complete. complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Concern department Engineer before use on work.

Supplying and fixing the best quality approved make of SS heavy duty long body Tap including cutting and making good walls wherever required etc.complete,complying with standerd specification and as directed by the department officers. The quality and make of angular stop cock should be got approved by concern department engineer before use on work.

Supplying & fixing in position 15 mm dia brass/ C.P screw down tape(Piller tap) (Heavy duty) of approved make conforming to I.S. Specifications & quality including cost of shellac, thread etc., complying with standard specifications & including cutting & threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the work).

Supplying,installing,testing and commissioning best quality approved/equivalent make of Single Bowl with drain board 600X600X200 mm stainless steel sink with brass Chromium Plateds wivalty peex tended swing sink cock 32mm dia CP waste coupling, 32mm dia heavy duty waste hose with extension pipe, 15mm CP angle valve with CP inlet connection tube,CP wall flange, including necessary bracket set ccomplete complying with standard specification and as directed by the Department officers.The quality and make o fsink and brass CP coated swiv al type sink cock should be got approved by Concern department Engineer before use on work.

Supplying and fixing Brass Chromium Plated Towel Rail 60cm long and 20mm dia with brackets of same materials including cost of teak wood plug & CP screws etc., complying with standard specification and as directed by the Department officers.

Supplying and fixing C.P. Robe hook fixing with necessary screws etc., complete. fixed on the toilet door complying with standard specification and as directed by the Department officers. The quality and make of coat hook should be got approved by Concern department Engineer before use on work.

Supplying and fixing Brass Chromium Plated Soap Tray of size 150mm x 100mm using rawl plug & brass screws for fixing etc., complete complying with standard specification and as directed by the Engineer Incharge before use on work.

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works).

50 mm dia

75 mm dia

110 mm dia

160 mm dia

200 mm dia

Supplying & fixing in position PVC Nahini / Floor trap of size 100x75mm including stainless steel gratings of approved brand & quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( One part of lime, two parts of sand & five parts of 40 mm size brick jelly ) & finished with cement mortar 1:3 ( One cement & three sand ) including dismantling masonry works wherever found necessary & making good the damaged portions to the original condition & giving connections to the cast iron pipes etc., complete, complying with standard specification. (The PVC Nahini / Floor trap should be got approved by the Executive Engineer before use on works ). a) 110 x 75 mm dia (20 mm water seal)

Supplying & fixing in position 150 X 100 mm square mouth 'P' or 'S' trap stone ware Gully trap 'A' grade with cast iron double gratings of size 150 X 150 mm with C.I. air tight cover with frames of size 300 X 300 mm at bottom & top respectively with necessary earth work excavation, laid over a bed of brick jelly cement concrete 1:3:6, 150 mm thick using 20 mm size broken brick jelly including necessary brick work & plastering, &including dismantling masonry wherever necessary & redoing the damaged portions to the original condition & by using cement concrete 1:3:6 using 20 mm stone jelly for fixing the Gully trap & giving connections to the stone ware sewer line etc., complete, complying with standard specification. (The stone ware gully trap should be got approved by the Executive Engineer before use on works ).

Constructing Brick masonry manhole various size of deep in cement mortar 1:5 ( 1 Cement: 5 coarse sand ) R.C.C. Raft & top slab with cement concrete 1:2:4, plain cement concrete 1:4:8 mix for base course (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size )above that 150 mm thick RCC M25 raft slab inculding reinforcement 10mm dia 150mm c/c bothways. Plastering inside walls with 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand ) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ), finished with a floating coat of neat cement ,supplying and fixing SFRC manhole cover with farame of size 600x600 mm, PVC foot rest as per detailed drawing etc the quoted rate shall also necessary excavation and back filling etc complete.complete as per standard design : (the chamber and cover should be got approved by the Executive Engineer before use on works)).

600x600mmx 600mm deep

900x 900mm x 1000mm deep

1200x 1200mm x 2000mm deep

Supplying, laying and jointing CPVC pipes SDR 11(having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using CPVC adhesives and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works. Internal & Vertical

15 mm dia

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

Supplying, laying, jointing, testing & Commissioning of UPVC Schedule 80 pressure pipes as per ASTM D 1785 with Sch 80 Fittings as per specifications, jointing with hold tite / super tite & tefflon tape and complete with fittings such as sockets, unions, reducers long or short bends, elbows, nipples flanges,checknuts,etc. Pressure testing of piping and back filling of trench complete as required. The quoted rate shall include necessary earth works, fittings like Tees, Bends, Offsets etc., G.I. brackets with pvc coated GI clamps, nuts & bolts, anchor fasteners, grip bolts, GI threaded, rods, etc., complete for external pipes. (For under ground or above ground external water supply piping.) Vertical & External

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

Supplying, installing, testing and commissioning of approved make full way lever operated forged brass ball valve of brass body with forged brass hard chromeplated steel ball tested to a pressure not less than 20 Kg / sqcm with threaded joints complete.

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

Manufacturing, supply and delivery of resilient seated wafer type butterfly valve in accordance with EN 593, centric disk mounted in three maintenance-free bearing bushes, tight in both flow directions, Replaceable rubber sleeve with integrated seal for functionally reliable use for flared flanges, welding flanges, PE flanges as well as loose flanges with V-collar, Stable seat due to collar with vulcanized support ring. Vacuum tight upto 1 Torr. Face to face length acc.to 558-1, basic series 20(DIN 3202/k1). With Electrostatic epoxy powder coating (EP-P) inside and outside color blue RAL 5005 with minimum coating thickness of 250 microns. The EPDM rubber & Epoxy Powder should be approved by W 270.(EP-P it is resi-coat powder approved for drinking water application, applied through fusion bonding technology process by dipping the shot-blasted casted components heated up to 200 deg C) and with 5 years warranty

65 mm nominal bore

80 mm nominal bore

Supplying and installing, in position of approved quality high pressure rated Gun Metal/Bronze Float operated ball Valve with rough body with plastic ball float and brass rods of required length suitable for test pressure of not less than 10 Kg/sqcm. a)50 mm nominal bore

Supplying &installing, Chrome plated forged brass body and cover Auto Air release valve for domestic and flushing water supply risers, suitable for pressure not less than 15 Kg/Sq.cm. a)65 mm nominal bore

Construction of Valve chamber 900x800x900 MM with approved Brickwork in CM 1:5 over a bed of 100 mm thick PCC1:4:8 and 12 mm thick internal wall plaster smooth in CM 1:3 with water proofing compound of CICO No:1 and 12 mm thick external wall plaster rough with sponge finish in CM 1:3 with water proofing compound of CICO No:1, also providing RCC cover slab of 100 mm thick with 8mm dia reinforcements at 150 mm ctc bothways top and bottom with required shuttering including curing with all necessary provision for complete size of chambers for valves up to65/ 80mm / 100mm dia. etc. complete complying with standard specification and as directed by the Department officers. DI Cover will be paid in the separate item. a)Inside size 900 x 800mm and 900 mm deep

Supply and delivery of Woltman model with removal mechanism water meters, (Bulk type) conforming to ISO 4064 part I, II, III Class B and IS-2373 with life cycle test certificate from FCRI/ NABL accredited lab. The water meter shall have magnetic drivers or mechanical drivers and shall be versatile for installation in any position. The meters shall be hydrodynamically, hydrostatically balanced. The runner, runner chamber, pointers of the meter shall be as per ISO 4064 specification. Dry dial excavated counter housing fully protected against flooding ensuring easy reading in all climates. a)80 mm nominal bore

Conducting Geophysical survey, quality and quantity test and transportation charges etc, (This includes labour charges in the field, rent of the vehicle for reaching the place, rent of the instrument and excluding charges for the geologist)

Drilling of Borewells anywhere in Tamilnadu including transportation from one place to another within Tamilnadu in alluvial soil sedimentary strata of clay and sandstone shale pebbles boulders etc . By first taking a pilot bore of 140mm/150mm dia and then enlarging to required dia direct or reverse rotary mud circulation method using rotary rigs, fuel ,labour and drilling bentonite and water required for drilling at site (site will be shown by the concerned officers) including construction of mud pit (Tamil Nadu Water Supply and Drainage Board )

Upto 60 m Depth ending below ground level

From 60 m upto 90 m Depth ending from ground level

Reaming 140/150/200mm dia pilot bore to 300mm dia bore as directed Upto 120 mt. Depth ending below ground level

Upto 60 m Depth ending below ground level

From 60 m upto 90 m Depth ending from ground level

Supplying and delivery of Casing Pipes 150 mm Dia for Bore Wells. The rate including cost and conveyance of materials.

Supply of 150mm dia OD PVC End cap as per special specification.

Labour charges for inserting 150mm dia of PVC casing pipes- assembly in the drilled hole including jointing the pipes with PVC coupler with cement paste etc complete ,supply and packing the annular space with pebbles of size and quality as approved by the concerned departmental officers.

Charges for developing Borewell with air compressor of 300CFM (100/150 PSI) capacity (minimum 8.00 hours ) including transportation , labour and fuel charges for compressor as directed by the concerned departmental officers etc complete and also conducting by V notch method.

Supply and Delivery of Automatic Single Phase Panel Board Star Delta with Two Level Guard and Auto Start Suitable for 2.0HP Submersible Motor Pump Set with Duty Condition of 150 LPM and 25m Head with ISI Make Suitable for 150 mm Size Bore Well as per IS 8034 Specification.etc., Complete

Labour charges for the erection of submersible pumpset in borewell / openwell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, Voltmeter, Ammeter, three pilot indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pumpset and trail run for 10 days.

Supply of and Delivery of 63mm HDPE pipe class PN 8 With ISI Make including cost of all materials charges etc., complete as per Special Specification.

Supply and delivery of PVC insulated and sheathed three core 2.5 Sq.mm Flat type copper cable conforming to IS 694/1990. Complete.

Supply and delivery of the following water supply materials with ISI make

Supply 8" bore Cap for Bore well

Supply MS 32/40mm MS clamp set for Bore well

Supply 50mm dia GM Non return valve for Bore well

Supply 12mm dia Nylon Rope for borewell

Priming Tank mounted with the supporting arrangement fabricated using MS angle for the height of 3 metres from the floor level, inlet, outlet, and drain arrangements inside the firefighting pump room, as directed by the Departmental Officers. a)Sintax tank

Providing and laying spreading and compacting graded stone aggregate to Wet Mix Macadam(WMM) specification including premixing the material with water at OMC in machanical mix plant carriage of mixed material by tipper to site laying in uniform layers 250mm thick with pavers in SubBase/Base course on well prepared surface and compacting with vibratory roller to achieve the desired density including cost of material,labour charges, rentals for machinery, fuel and all other incidental charges etc., complete.

Supplying and laying of 83mm thick high strength type of interlocking using rubber mould for the paver blocks with design and approved colour and manufacture with concrete mix 1:1:2 using 10 to 12mm size HBG stone jelly, in required shapes and sizes having minimum compressive strength of 40N/m2 to be laid in flurrying bone pattern with approved non sticking surface at top. the rate is inclusive of levelling the site, providing 'M' Sand cushion 100mm thick below 6mm thick graded chips grouting and also inclusive of transportation charges, loading, unloading and labour charges for laying the paver block etc. complete complying with standard specification and as directed

Supply and fixng of TNEB meter board suitable for 3phase 100A service connection made up of suitable angle iron framework of size 2 feetx1-1/2 feet using angle iron of size1-1/2"x 1-1/2"x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1-1/2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3Nos. 100A fuse units (500V), 1No. neutrallink, copper earth flat of size1"x1/4" with interconnection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with earth connection complete

Supply and laying of 3-1/2 x 120 sq.mm. PVC LTUG aluminium armoured cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and fixing of brass cable gland for 3-1/2 x 120 sq.mm. PVC LTUG aluminium armoured cable with earth connection

Supply and providing cable end termination of 3-1/2 x 120 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Supply and fixing of 200 A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with earth connection only.

Supply and fixing of 8 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB Incomer ) with double door (metal door) with 1 no. 160 A 4 P MCCB switch as incoming and 6 nos. 63A 3P MCB , 6 nos. 6A to 32A SP MCB as outgoing with suitable cable end box on wall with earth connection only. Higher End

Supply and fixing of 7 segment 4 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 4 ways in each segment) and seperate provision for MCB / Isolators ( totally 12 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only.

Supply and fixing of 7 segment 8 way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and seperate provision for MCB / Isolators ( totally 24 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only.

Supply and laying of 4 x 10 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15metre layer of sand and covering the cable completely with brics and sand and refilling the earth to make good

Supply and laying of 4 x 16 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15metre layer of sand and covering the cable completely with brics and sand and refilling the earth to make good

Supply and laying of 4 x 6 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15metre layer of sand and covering the cable completely with brics and sand and refilling the earth to make good

Supply and installation of Miniature circuit breakers 240 v / 415v 50hz - ac supply suitable for both lighting and Motor circuits - higher end. Four Pole 6 A to 32A, 10KA

Supply and installation of Sheet steel enclosure for mcb’s - higher end 4 pole

Supply and installation of RCCB / ELCB four pole - higher end 40 Amps 30 MA

Supply and installation of RCCB / ELCB - higher end 10 Amps 30 MA DP

Supply and installation of Sheet steel enclosure for mcb’s - higher end 2 pole

Supply and fixing of brass cable gland for 4 core x 6 sq.mm. PVC LTUG armoured cable with earth connection.

Supply and fixing of brass cable gland for 4 core x 10 sq.mm. PVC LTUG armoured cable with earth connection.

Supply and fixing of brass cable gland for 4 core x 16 sq.mm. PVC LTUG armoured cable with earth connection.

Supply and providing cable end termination of 3-1/2 x 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete (FRM PARKING VTPN TO EXPANSION HIGHMAST-1&2)

Supply and Run of 2 of 2.5 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 2.5 sq.mm copper wire and making good of the concealed portion

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End

Wiring with 3 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC pipe Stair case Light point Higher End

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with painting of suitable colour for concealed PVC pipe Plug point ( 8 points / Coil) Higher End

Wiring with 2 x 4 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitablePVC rigid pipe Concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 16A one way module switch and 1 no. 16A 3/2 pin module socket with module front plate with continuous earth wire connection of 4 sq.mm copper wire and making good of the concealed portion with painting of suitable colour for Concealed PVC pipe power Plug point ( 8 points / Coil) Higher End

Supply and fixing of 20Amps DP Plug and Socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug) [ ISI marked / Reputed make] Wall mounted fan

Wiring with 2 x 4 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitablePVC rigid pipe Concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 16A one way module switch and 1 no. 16A 3/2 pin module socket with module front plate with continuous earth wire connection of 4 sq.mm copper wire and making good of the concealed portion with painting of suitable colour for Concealed PVC pipe power Plug point ( 8 points / Coil) Higher End (less 16A socket)

Supply and fixing of 300mm (12") sweep (lightduty) Ac exhaust fan complete with necessary wall opening and making good of the wall

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan

Supply and fixing of BEE Energy efficient 1200mm Sweep Ceiling Fan 5 Star Rated, inverter driven controlled by microprocessor with 300mm down rod with regulator / remote control (35 W)

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB Isolator as incoming and 12 nos. 6A to 32A SP MCB as outgoing on suitable angle iron frame on wall with earth connection only. Higher End

Supply and Run of 1 of No.8 SWG GI wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Supply and fixing of 18W 4 Feet LED Fitting with LED (higher end)

Supply and fixing of 18W 4 Feet LED Fitting with LED (Lower end)

Supply and fixing of LED indoor Fitting of 24W LED 4000K 2 x 2 Square Type Recessed Fitting with LED (Lower end)

Supply and installation of Mirror Light 20W LED Batten

Supply and installation of LED foot lamp.

Supply and fixing of LED indoor Fitting of 18W LED 3000K Square Type Recessed Fitting with LED (Lower end)

Supply and installation of Gong Bell 9” size suitable for 250V

Supply and installation of 20 Amps key card switch- Electronic(3M)

Supply and installation of 25mm X 6mm GI strip

GST at 18%

S J INFRA (BID ID -1257867)