PROVISION OF COVERED SHED FOR TECHNICAL TRAINING CLASSROOMS OF DRIVER MT FOR AGNIVEER TRG AREA ALONGWITH PATHWAY UNDER GE BHOPAL

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cmdeep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundations etc. or for shafts, well cess pits, manholes, pier holes, etc. but not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in hard/dense of soil complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation, sub base concrete etc complete all as specified and directed.

Use&waste for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams;and similar work, vertical or tobatter complete all as specified and directed.

Use&waste for formwork to sides of pillars,posts, struts, piers, columns and stanchions complete all as specified and directed.

Use&waste for formwork to sides and soffits offloor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelvesincluding supports, overhangs,etc. also splays between floors and beams, etc complete all as specified and directed.

M&L for design mix, M-25 cement concrete foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for design mix, M-25 cement concrete as in coloumns, lintel beam, roof beam etc. complete all as specified and as directed.

M&L mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per ser items 9.00 here-in-before but 6 to 8mm dia complete all as specified and directed.

All as per ser items 9.00 here-in-before but 5mm dia and over and upto 10mm as in stirups and binders complete all as specified and directed.

M&L for brick work with fly ash brick with modular size straight or curved on plan exc 6 m mean radius, built in CM 1:6 all as specified and directed.

S&F steel work in tubular/angle trusses including special shaped washers, purlins, rafters, posts etc complete all as specified and directed.

M&L pre galvalume aluminium zinc coating GI based corrugated steel sheet (AZ-150) of 0.50 mm thick of any colour having tensil strength of 550/MPA as in roof covering/cladding to wall/ ridge,fixed with self tapping screw/L type or J type cranked hook bolts all as specified and directed by Engr in Charge.

M&L pre-painted galvalume aluminum zinc coating GI based plain steel sheet (AZ-150) of 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding towall, fixed with self tapping screws all as specified and directed.

S & F mild stell work in hand rails, half round or other steel section or core for wooden hand-rail straight portion,drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concreteand screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shapeas directed, drilling holes,notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all as specified and directed

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth all as specified and directed

M&L for preparation new steel & iron surfaces of any description over 10cm in width or girth and applying two coat of synthetic enamel paint over and including a coat of red oxide zinc chrome primer complete all as specified .

M&L for galvanised cold rolled steel section frame work size 600x600 grid size 24x38x0.50 (composite thickness) Tee (bottom pre-coated ) and size 24x24x0.50m (composite thickness) thick wall angle , galvanised cold rolled steel section including suspenders as per (Gapsec) manufacturs insturction as in ceiling complete all as specified and directed.

M&L for 6mm asbestos free calcium silicate board of size 600x600x6mm thick fixed to steel frame work as in ceiling , including applying two coats of oil bound distemper all as specified and directed.

M & L for fabricating and fixing powder coated (Minimum 50 miciron ) aluminium sections of required size for doors, windows any type, frames and partitions including aluminium hinges of required size jointing cleats, screws salsh fasterners, plug for fixing with walls, column etc including taking down damage portion of damage door, windows complete all as specified and directed. Note :- Rates are inclusive of necessary new fitting for door/ window/partio i.e handle, tower bolt, butt hinges, beading etc complete

S & F of 4.8 mm thick sheet glass, ordinary quality fixed in aluminum doors/partions in square exc 0.5sq. m in each pane

S & F of 3mm thick Aluminum composte panel (ACP), exterior grade, PE core, PVDF coated of approved shade. Complete all as specified.

S & F 140mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed

M&L granite 16-18 mm thick (of any type) work (machine cut) in steps, jambs, pillar, window-cills, cooking platform and like in 15 mm thick cement mortar (1:4) including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 using water proofing compound faces of brick or concrete surfaces (external surfaces) finished fair, even and smooth without using any extra cement complete all as specified and directed.

Supply only Integral water profing compound mixed with cement mortar complete all as specified and directed.

M&L for 15mm thick rendereing brick or concrete surface in CM 1:6 finishing the surface fair & even without using extra cement complete all as specified and directed.

M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm incl preparation of new surfaces complete all as specified and directed.

M&L for applying one coat of white wall putty 1mm thick on walls complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all as spd and as directed.

Removing surplus soil obtained from excavation to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting paint complete all as specified and directed.

M&L moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for design mix M-25 cement concrete as in floor slab complete all as specified and as directed.

M&L for light colour vitrified ceramic tile light shade 7 - 8 mm thick (square /rectangular ) polished, area of each tile n.exceeding 0.36sqm as on floor with expoxy filling in joints over and including 15mm thick rendering in CM 1:6 set & jointed in neat cement slurry & pointed in white or coloured cement to match complete all as specified & directed.

M&L for vitrified ceramic tile light shade 7 - 8 mm thick (Square /rectangular ) polished , area of each tile n.exceeding 0.36 on vertical surfaces with expoxy filling in joints for skirting dado and risers to steps etc over & including 10mm thick rendering in CM 1:4 set & jointed in neat cement slurry & pointed in white or coloured cement to match complete all as specified & directed.

M&L for 75mm thick PCC 1:3:6 type C-2 using 40mm gradded stone aggregate as in plinth protection including bitumen and sand filling in joints complete all as specified and directed.

M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed..

M&L for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L treating the soil along with externalperimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658 -2006 of 60 mm thickness, M-35 grade with grey cement and pigment for path etc over and including 50 mm thick sand cushion complete all as specified and directed.

M&L for point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits), with multi-stranded copper conductor-stranded copper conductor 1.5 Sq. mm nominal cross-sectional area, single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked with valid CML No. in and including medium grade, PVC concealed conduit and conduit accessories concealed in wall/roof/floor etc, ISI marked with valid CML No.(IS-9537-1983 for conduits and IS:3419:1976 for conduit accessories), with sheel metal mild steel flush box, white cover plate with frame for fixing modular switches, sockets and fan regulators etc, including PVC insulated multi-stranded copper conductor 1.5 Sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed.

All as per item No 43.00 but here-in-before but 3 pin socket outlet 5 Amps 240 volt on same board complete all as specified and directed.

All as per item No 43.00 but here-in-befor 3 pin socket outlet 5 amps on independent board elect wiring 1.5 sq mm complete all as specified and directed.

All as per item No. 43.00 here -in- before but wiring with 4.0 Sq mm FRLS mutistranded copper conductor cable for 5/15 amp switch socket combination on independent board and with 4.0 Sqmm, FRLS insulated multi-stranded single core earth wire for earth continuity, connected to common earth dolly complete all as specified and directed.

S&F Modular, single pole, 1 module, one way, 6/16 Amps, 240 volt, 50Hz, AC, ISI marked complete all as specified and as directed.

S&F in repairs ceiling rose surface bakelite, three terminals, 240V, 50Hz, ISI marked complete all as specified and as directed.

S&F modular socket outlet, 2 module, multipurpose having provision for 2 & 3 pin, 6/16 Amp flush type, 240 volt AC complete all as specified and as directed.

Supply and fixing BEE 5, star, rated, BIS certified BLDC decorative ceiling fan 1200mm sweep, 230Volt, Minimum air delivery 225 CFM, anti dust, aerodynamic aluminium blades & body with advanced brushless technology bosed BLDC copper winding motor with all accessories such as regulator, conneting down rod, clamps, canopy, remote with boost, timer & sleep mode including taking down old fan complete all as specidied and directed. Note:-(i) Cost of taking down old ceiling fan, regulator & deposit to MES Store yard in deemed to be included in quoted rate. (ii) Warranty of BLDC ceiling fan for 2 year & 5 Year of BLDC Motor.

Supply and fixing energy saving LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum housing toughened glass thermal shock and impact resistance and heat resistant complete with powered by integrad electronice driver with out put short circuit protection, surge protection, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete toughened glass, lens IP 66, IK-08 and with system efficacy of 125 lm/W CRI >70 , PF≥0.95 complete all as specified and directed.

M&L for sub main wiring with two single core FRLS PVC insulated unsheathed cable 1100 volts grade, 4.0 Sqmm size, ISI marked with multistranded copper conductor, drawn in non metallic rigid PVC conduit of size 25 mm dia ISI marked including PVC insulated unsheathed 4.0 Sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dolly complete all as specified and directed. Note:- Two runs of 4.0 sqm dia FRLS wire, one runs of earth wire and one PVC conduit will be measured in one length.

S&F LED 20/21Watt tube light fitting (T8 type), including LED retrofit tube 20/21 W one side connection type, 240 v, PF > 0.90, colour Temp 6500 K, System Luminious efficacy > 100Lm/W, complete with powder coated CRCA decorative patti suitable for surface mounting on wall, complete fitting including connecting with PVC insulated multistranded copper flexible cable 0.5 sqmm two core, and PVC round block white colour x 2 Nos for mounting of fitting complete all as specified & directed.

S & F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 200 amps rated busbar, 08 way, double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43, including wooden rectangle board of first quality of suitable size for mounting of DB box complete all as specified and directed.Make- Legrand/ Seimens/ Schinder.

S & F in repairs MCB, SPN suitable for 240 volts, AC supply 32 Amps, C Curve, with over load and short circuit protection and rupturing capacity not less than 10KA complete all as specified and directed. Legrand/Siemens/ Schneider or equivalent all as specified and directed.

S&F MCB, SP 240 volts 6 to 32 Amps, 10 KA breaking capacity, 'B' Curve including connection with suitable size aluminium / copper lugs complete all as specified and directed.

Supply & fixed star energy saving Air Circulator fans 230 volts single phase oscillating 450 mm sweep suitable for wall mounting. complete all as specified and directed by Engr-in-charge.

S & F lamp holder PVC/polycarbonate type with back plate ISI marked suitable for batten fittings with 9 Watt LED Bulb inveter type complete all as specified and directed by Engr-in-Charge.

M&L for earthing complete with galvanised steel earth plate electrode 60×60cm×6mm thick, buried directly in ground (earth pit not less level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised iron earth wire of 4.0 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 SSR including earth pit in any soil char coal common salt , 15 mm all around earth plate PCC (1:3:6) type culprit, with 40 x40x6 mm angle iron frame and PCC cover (1:2:4) type B1 using 20mm graded stone aggregate, water pipe funnel and GI protection pipe light grade 15mm dia upto panel connecting earth lead to panel all as specified and directed by EIC. Note : Earth continuity conductor including protection pipe up to 7.5 mtrs from earth electrode will be included in unit rate.

Excavation in trenches nexc 1.5 mtr wide and n exc 1.5 mtr in depth and getting out in soft/ loose for laying cables, erection of poles complete all as specified.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified.

Removing surplus excavated soil nexc 50 mtr and depositing where directed at a level n-exc 1.5 mtr above the starting point.

Sand cushioning/sand covering for underground cable protection complete all as specified and directed.

Supplying and laying Class LV, Type I, flat, size 250mm x 150mm x 40mmfor cable protection cover laid flat and dry in trenches over the cable perpendicular to the direction of cable complete all as specified and directed.

Supply and Laying XLPE insulated, PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 16x4 sqmm, laid in trenches/floor or fixed on wall/pole complete all as specified and directed.

S&F for 25 mm bore GI tubes, 'light grade' galvanised, with all fitting and laid in floors, under road, pavement or hard standing steel water tubing complete all as specified and directed.

Deduct Schedule of credit (calculation will be done off line) Rs. 0.00