IMPROVEMENT OF BUSSTAND AT WARD NO 5,SURVEY NO 132 IN THIRUTHURAIPOONDI

Amount

IMPROVEMENT OF NEW BUSSTAND

BORED PILE 400 mm Dia Boring, Providing and installing Bored cast-in-situ reinforcde cement concrete pile of specified diameter and length beloow the pile cap in cement concrete 1:1.5:3 ( 1 cement 1.5 coarse sand & 3 graded stone aggregate of 20 mm nominal size) to carry a than specified, excluding the cost of steel reinforcement but including Benotite solution machinery charges labour charges etc., all complete. (Length of pile for payment shall be measured bottem pile to the bottem of pile cap). 300mm dia piles Details of cost for 20m length of pile material- Pile Cap

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete Footpath

Earth work excavation for foundation in all type of soils as may be directed except in hard rock requiring blasting with initial lead of 10m and lift of 2mts, including refilling the sides of foundations with excavated soil in layers of 15cm thick well rammed and consolidated and depositing the surplus earth within the compound in places shown by the departmental officers complying with the standard specification and drawing as directed by departmental Engineers.

Supplying and filling in 'foundation and basement with filling sand in layers of not more than 15cm.thick well rammed watered and compacted -1m3 etc., complete complying with standard specification.

Supplying and filling in 'foundation and basement with Well Gravel in layers of not more than 15cm.thick well rammed watered and compacted -1m3 etc., complete complying with standard specification.

Plain cement concrete of mix 1:4:8 (one cement four sand eight course agreegate using hard broken granite stone jelly of 40mm gauge for foundation levelling course including shuttering dewatering wherever necessary and laid in layers of not more than 15cm thick etc., complete cost including all materials costs, labour chrages, conveyance and all other costs etc., complete as per standard specification.

Cement Concrete 1:3:6 (One Cement, Three sand and Six broken stone jelly) using 20mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. (Reinforced Cement Concrete 1:2:4 for slab to be extended upto top of splashing with pressed tiles and future extension rods to be embedded in CC 1:3:6 (One Cement, Three Sand and Six hard broken stone jelly). Dummy columns should be at least 1 metre height) Cycle Shed

Plain Cement Concrete 1:2:4 (one cement, two fine aggregates and four coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification

Supplying and erecting centering for sides and soffits including support and strutting upto 3.50m high for plain surface with all cross bracing using mild steelsheet of 90cm X 60cm and stiffened with welded mild steel angle of size 25mm X 25mm X 3mm for boarding laid over silver oak ( country wood) joists of size 10cm X 6.5cm ( space at about 90cm c/c and supported by casurina props 10cm to 13cm dia spaced 75cm c/c etc., complete, cost including all materials costs, labour chrages, conveyance and all other costs etc., complete as per standard specification. For Grade beam Without Strutting (For Plinth Beam and Footing)

Supplying and erecting centering for sides and soffits including support and strutting upto 3.50m high for plain surface with all cross bracing using mild steelsheet of 90cm X 60cm and stiffened with welded mild steel angle of size 25mm X 25mm X 3mm for boarding laid over silver oak ( country wood) joists of size 10cm X 6.5cm ( space at about 90cm c/c and supported by casurina props 10cm to 13cm dia spaced 75cm c/c etc., complete, cost including all materials costs, labour chrages, conveyance and all other costs etc., complete as per standard specification.For Columns

Supplying and erecting centering for sides and soffits including support and strutting upto 3.50m high for plain surface with all cross bracing using mild steelsheet of 90cm X 60cm and stiffened with welded mild steel angle of size 25mm X 25mm X 3mm for boarding laid over silver oak ( country wood) joists of size 10cm X 6.5cm ( space at about 90cm c/c and supported by casurina props 10cm to 13cm dia spaced 75cm c/c etc., complete, cost including all materials costs, labour chrages, conveyance and all other costs etc., complete as per standard specification.With Strutting (Lintel, Beams and Slabs)

Supplying and erecting centering for sides and soffits including support and strutting upto 3.50m high for plain surface with all cross bracing using mild steelsheet of 90cm X 60cm and stiffened with welded mild steel angle of size 25mm X 25mm X 3mm for boarding laid over silver oak ( country wood) joists of size 10cm X 6.5cm ( space at about 90cm c/c and supported by casurina props 10cm to 13cm dia spaced 75cm c/c etc., complete, cost including all materials costs, labour chrages, conveyance and all other costs etc., complete as per standard specification.With StruttingAngular Bus Bays (Half the slab rate)

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors.

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification Solar Minimast

Supplying and laying Rubberised interlocking Paver block M40 grade Providing and laying of 63mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, stone dust cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification, - Footpath

Supplying and fixing in position FRC.Manhole covers (light or heavy duty) mof 60cm sizes of best approved quality and as per atandard specifications etc.,complete - Footpath

Providing Bitumen Felt Pad of 15mm thick including cost of materials, labour charges etc., - M-30 Pavement Area

Polished Rajasthan Kota Stone Slabs of 20mm thick with Machine Cut Edges of size 2'0" x 2'0" in size laid over base layer of cement mortar 1:3 (one cement and three plastering sand) - 20 mm thick and applying cement slurry & pointed with white cement and colour pigments to the colour of stones and polished neatly as directed by the departmental officers. - Angular Bus Bay Area

Supply and Installation of Tensile Polyester Fabric minimum of 1050 gsm (Ferrari TX 30) Tensile Membrane with 30 years warranty, including MS Structural Steel work finished with two coats of epoxy paint colou, 12mm SS rope with stay accessories etc., complete. - Tensile roof area

Supplying and Erecting Pull and Push Type Rolling Shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc - Double Row Shops

Supply and Installation of Tensile Polyester Fabric minimum of 1050 gsm (Ferrari TX 30) Tensile Membrane with 30 years warranty, including MS Structural Steel work finished with two coats of epoxy paint colou, 12mm SS rope with stay accessories etc., complete.- Cycle Shed.

Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS staandards. (No separate payment will be made by the Department for the excess usage of materials) .Upto Basement

Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS staandards. (No separate payment will be made by the Department for the excess usage of materials) Above Basement

Providing and laying in position Standardised Concrete Mix M-25 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 350Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone sand (M- Sand) but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS standards. Angular Bus Bays

Providing and laying in position Standardised Concrete Mix M-30 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 400Kg/ cum and maximum water cement ratio of 0.45 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone sand (M- Sand) but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS standards. M-30 Pavement Area

Reinforced Cement concrete 1:1.5 :3 (one cement, one and half sand & three course aggregate) using 20mm gauge hand broken/ and broken granite stone for all RCC items of works excluding centering shuttering and cost of reinforcement but including curing etc.,complete and also including fixing fan clamps and fixtures in rcc works wherever necessary as directed by departmental officer etc., complete. - Sewage arrangements

A) Brick work in cement mortar 1:5 (one cement, five sand) using II class ground moulded chamber burnt bricks of size 8-3/4 " x 4 -1/4" x 2-3/4" approved quality & strength etc., complete, cost including all materials costs, labour chrages, conveyance and all other costs etc., complete as per standard specification. For Upto Basement and Foundation

B) Brick work in cement mortar 1:5 (one cement, five sand) using II class ground moulded chamber burnt bricks of size 8-3/4 " x 4 -1/4" x 2-3/4" approved quality & strength etc., complete, cost including all materials costs, labour chrages, conveyance and all other costs etc., complete as per standard specification. For Superstructure

Plastering CM 1:5 (One cement and five sand) mix 12 mm thick etc., complete, cost including all materials costs, labour chrages, conveyance and all other costs etc., complete as per standard specification.

Plastering CM 1:3 (One cement and three sand) mix 10 mm thick etc., complete, cost including all materials costs, labour charges, conveyance and all other costs etc., complete as per standard specification.

White washing two coats using best quality slacked shell lime including cleaning surface watering curing including cost and conveyance of all materials at site and all labour charges etc., complete, cost including cost and conveyance of all materials, labour charges and all other incidental charges etc., complete as per standard specifications.

Painting two coats with approved First quality plastic emulsion paint over cement plastered wall surface and ceiling including cost of one priming coat, Cost of all materials, all labour charges, brushes, cleaning preparing the surface,scaffolding charges and curing charges etc., complete, cost including cost and conveyance of all materials, labour charges and all other incidental charges etc., complete as per standard specifications.

Painting two coats for Exterior surface with approved Exterior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. Cycle Shed

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the departmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 200mm x 200mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Flooring with following antiskid tiles of size 600 x 600 x 9 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with Glazed tiles of sizes 305mm X200mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:2 (one cement ,two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Supply and Fixing of 10 Metre Length octagonal Pole with Base Plate fully Galvanised with fittings (bottom 240mm, Top 120mm and 3m thick ) with 60 watts Solar Street light - 6 Nos (60 watts LED, 80 watts Mono Panel, 36 AH lifepo 4 Battery) Foundation Bolt, Nut M24-800mm long- 4 Nos,including Errection and Commissiong of 10 Meter Mini Mast Complete set with the help of suitable Special type Machinery such as crane and all tools Paints and including all cost and coveyence etc complete - Solar arrangements

Supply and Delivery of LT Cables 3.5 Core, 240 Sqmm 11KV armoured aluminium conductor cross linked Poly methylane insulated PVC sheathed cable conforming to IS 7098 part 1 1988 Ano as amended thereafter with ISI making

Labour charges for Cable below the Ground Level including earthwork, cost and conveyance etc.,

Supply, Delivery and Fixing of Panel Board for getting 70m. New EB Service connection

Supply and clarnping of 2 x 10 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply, Delivery and Fixing of 20 W 4 Feet LED Fitting etc., complete.

Supply and Delivery of 120W LED Street Light Fitting with LED Fitting etc., complete.

Labour charges for fixing above LED Fitting etc., complete.

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Wiring with 2x1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires in flush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch and making good of the concealed portion with suitable colour for PVC concealed light / Fan Point (For electronic regulator) (5 Points Per Coil) as per (SD 25)

Wiring with 2x1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, with 150mm x 100mm x 113mm TW switch box with 3 mm thick Hylem sheet cover for 5 A 3 pin non inter locking CS Plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point.as per (SD 38)

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC ccessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed light point / Fan point (For Electronic regulator). etc, complete as per standard specifications. SD 23

Supply and run of 2 of 1.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour.etc, complete as per standard specifications SD 54

Earthing as per P.W.D. standard with an earth electrode of 2Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work. etc, complete as per standard specifications SD 234

Supply and fixing of 3 phase 4 wire 4 way ICDB of 32 A per way with 100 A TPN MC switch with suitable trunking box Ms cable entry boxes and internal connection on suitable angle iron frame work with earth connection etc, complete as per standard specifications SD. 175

Supply and fixing of Horizontal type 4 way triple pole neutral MCB distribution board in sheet steel enclosure with 40 A 4 pole MCB isolater as incoming and 12 Nos. 6A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. The MCBDB and MCB's should be with the ISI mark etc, complete as per standard specifications SD.179 1

Wiring with 2 x 4sqmm (56 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 15A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC power plug point. etc, complete as per standard specifications. SD 40

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1" x 1/8" copper flat) on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit sd 125.

Supply and fixing of 32 A TPN MC switch on incoming and 3 Nos 32 A DPMC Switch (Front Handle) as outgoing with suitable adoptor box with suitable MS cable entry box trunking boxes and internal connections on internal connections on suitable AI frame work with earth connection etc, complete.SD 172 1

Supply and fixing PVC Rainwater pipe of 110mm dia of 4 kg/cm2 for rain water down fall pipe with necessary specials, clamps etc., complete cost including all costs etc., complete as per standard specification.

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).complete.

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings.....

Wash Hand Basin of size 550mm x 400mm with all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia 'B' Class GI Waste Pipe, 15mm dia GM Wheel Valve, 15mm dia Nylon Connection, 15mm dia Brass Nipples, 15mm CP Pillar Tap etc

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works) SD Tap For Toilet & Urinals

Supplying and fixing of single box type 4' 20W LEDFitting complete with TW round blocks on wall or ceiling with PVC unsheathed leads from terminals to the fitting

Internal Water Supply - P.V.C. Pipes (6Kg/SqCm) Supplying laying and jointing P.V.C pipes (6Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.

32mm UPVC Pipe

32mm UPVC Union

25mm UPVC Union

32x25 UPVC Brass reducer

25x20 UPVC Reducer Elbow

25mm UPVC pipe

25mm UPVC bend

25mm UPVC tee

20mm UPVC tap

Supply and fixing in position of HDPE drinking water storage IS 12701/1996 tank of 1000 Litre capacity including loading, unloading transportation and labour charges for fixing G.I pipes and specials for pipe connection works with isi mark etc completed. (TWAD- Category no.17)

Supplying and Fixing of 6" dia PVC pipe 6 kg/cm2 including cost of materials, labour charges etc.,

Lowering PVC/ DWSC rigid pipes and specials to trench and laying to proper grade and alignment, jointing with PVC couplers with cement paste.

Refilling with excavated sand complying with standard specification for filling in foundation and basement

Supply and fixing of Heavy FRP Manhole cover upto 60mm dia of size including cost of materials, labour charges etc.,

SM Associates