SPL REPAIR TO (BLDG NO. -- 4 63) INCL REPLACEMENT OF LIGHTENING CONDUCTOR IN AM N CO Y DEPOT AREA AND SPECIAL REPAIR OF DRAINAGE NEAR CL K s PLAT OON TO SIGNAL DE T AT AM N CO Y UNIT AREA AND SPL REPAIR TO GUR AD POST NO 01 (BLDG NO P-1 71) AND G

Taking down cement plaster on stone masonry/Brick Masonry incl racking out joints, hacking for key scrubbing down with water and direction by Engr- In Charge.

M&L for 10 mm rendering in CM 1:6 on fair face of brick work or on concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for 05 mm rendering in CM 1:3 on fair face of ceiling or on concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 10 mm rendering in CM 1:4 on fair face of wall or on concrete surfaces finished even and fair with water profinfing compound (WPC) complete all as specified and directed.(WPC Measured seprately)

M &L for Preparation of new plastered surface of wall and applying two coat of oil emulsion distemper of approved tints over a coat of interior wall primer complete all as specified and directed by Engineer-in-Charge..

M &L for Preparation of new plastered surface of Ceiling and applying two coat of oil emulsion distemper of approved tints over a coat of interior wall primer complete all as specified and directed by Engineer-in-Charge..

M&L for preparing new plastered surface of wall and applying Two or more coats of 100% Premium acrylic emulsion paint of required shade, on external walls/RCC surfaces/soffits of chajjas/roof projection/cantilivers/balcony etc having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm, including necessary scaffolding arrangement as required at site complete all as specified and-as-directed.

M&L for complete removal of existing treatment incl preparation of wall surfaces and fill the crack of wall with crack filler paste and applying two coat of oil emulsion distemper of approved tints over one coat of primer to prepare the surface even and smooth, complete all as specified and directed by Engineer-in-Charge..

M&L for complete removal of existing treatment incl preparation of ceiling surfaces and fill the crack of ceiling with crack filler paste and applying two coat of oil emulsion distemper of approved tints over one coat of primer complete all as specified and directed by Engineer-in-Charge..

M&L for complete removal of existing treatment incl preparation of wall surfaces and fill the crack of wall with crack filler paste and applying Two or more coats of 100% Premium acrylic emulsion paint of required shade, , having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm, including necessary scaffolding arrangement as required at site complete all as specified and-as-directed.

M&L for preparation of old decorated steel surfaces of any description, not otherwise described over 10 Cm width & girth and applying one coat of synthetic enamel paint as camouflage / Ordinary pattern complete all as specified and directed by Engineer-in-Charge.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) area not exc1.5 Sqm each and removing from site complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each and complete all as specified and directed.

Taking down door/ windows incl frames and complete fittings of area exc 1.50 sqm but n. exc 4 sqm complete all as specified and as directed.

Supply and fixing 35mm thick, IInd class hard wood plain, framed, panelled factory made shutters with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete incl S & F fwg items As approved by Accepting Officer. (a) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (b) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16 x 300mm-1 No per leaf (d) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 No per leaf

S & F 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-I section 8 clause 8.20 (a) kiln seasoned and chemically pressure treated all as specifeid including stainless steel 304 grade wire cloth ( 0.36mm nominal dia of wire and average width of aperture 1.40 mm ) and incl supply and fixing following items:- (a) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf (b) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos per leaf

S&F in repair 100mm size MS butt hinges and fixed to PVC frame /Wooden Frame and angle iron frame by necessary welding complete all as directed.

S & F in repairs 200 mm long SS tower bolt (304 Grade) fixed with SS screw, complete all as specified and directed

S & F in repairs SS (304 Grade) bow handle, of 200 mm long fixed with SS Screw complete all as specified and as directed.

S & F in repairs SS (304 Grade) sliding door bolts of 300mm long with hasp and staple(bolt type) and fixing clips of sheets , fixing bolts and sliding bolts of extruded section with SS Screw, complete all as specified and directed.

S&F in repairs 140 mm floor door stopper of aluminium alloy body and tongue , anodised ,with hard drawn steel spring ,fixed in floor complete all as specified and directed

M&L for preparation of new wooden surfaces of any description, over 10cm in width or girth, not otherwise specified with two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as specified and as per drawing.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification incl the fwg S & F As approved by Accepting Officer (a) Stainless Steel (304 Grade) Finished Butt Hinges 125mm - 3 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf

S&F powder coated aluminium, three track sliding window frame of section minimum size 92.00x 31.75x 1.00 mm comprising of one No of fly proof shutter and two nos of glazed shutter frames of section size 32x18x1.00 mm thick with necessary joining cleats, glazing clips, rubber gasket, anodised aluminium snap beading and connected locking arrangement all as specified and directed. (Notes. (i) Glass filling in panels of window and stainless steel wire mesh/wire cloth shall be demed to be included in the quoted rate for the item, ii) stainless steel wire cloth in panels of fly proof shutter shall be 0.36mm nominal dia of wire and avg width of aperture 1.40mm, fixed with aluminium wire staples,. iii) Glass filling in panels of glazed shutter shall be 5mm thick tinted sheet glass of approved make and shade/tint and directed by Engineer Incharge.

M&L for powder coated aluminium frame and shutter for door, window, ventilators, partion and sliding shutters etc ( Minimum thickeness of powder coating 50 micron) with one or more rebates including jointing cleat, aluminium snap beading 20 x 15mm, rubber gasket, glazing clip for fixing etc .complete all as specified and directed by Engr in charge.

S&F 5mm thick figured / tinted sheet glass of approved make and shade/tint filling in aluminium panels door/window/partion with necessary joining cleats, beading all as specified and directed.

S&F aluminium grill made out of 7mm x 4.5mm w'ide flat, square ractangular or similar section, fixed with channel of size 38mm x 12mm x 13mm incl taking down (section 8778 complete all as specified (make: DECO GRILL No. DG 102 with aperture- 80mm or equipment as approved by GE.

S&F stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staples or with aluminium / wooden beads, stainless steel screws and nuts bolts etc for ventilator complete all as specified.

S & F for Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet, fixing of float valveand over flow pipe if required etc including taking down existing tank complete .

S&F in repair Stainless steel tubing of 20 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets & finials fency type, stops fixed with ss screws etc all as specified & directed. Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered as approved by accepting officer.

Supply & Fixing in repair 20 mm bore tubes medium grade galvanized with all fitting such as Tee, elbows, sockets, unions, plugs, short lenghts etc and fixed complete to walls and ceilings or laid in floors of any length including taking down or up existing GI tubing & connections all as specified and directed by Engr-in-charge.

S&F in repair 15 mm dia bib tap,fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified anddirected.

S&F in repair 15mm bore CP fancy type stop valves/angle cock, cast copper alloy, screwed both ends for iron pipe or for union complete all as specified and as directed.

S&F in repair 15mm bore CP fancy type, chromium plated with long shank and cup (concealed type) stop valves, cast copper alloy, screwed both ends for iron pipe or for union complete all as specified and as directed.

S&F in repair 15mm bore brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed. complete all as specified and as directed.

S&f in repair 15mm bore pillar tap cast copper alloy fancy type with capston heads, chromium plated screwed down high pressure, with or without letters Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipes and fixed all as specified and directed.

S&F in repair 110mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on trenches or in floors /wall complete all as specified and as directed.

S&F in repairs 75mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and as directed.

S & F in repair Vitreous china squatting pan of Orissa patten size 580 x 440 white colour including CI S/P trap long size as directed joint run and lead front or back inlet with integral footrest including connection to trap and to flushing pipe,anti-syphonage pipe, etc, fixed in repair complete and making good to floor in PCC 1:2:4 all as directed and specified.

S & F in repair Vitreous china premium/1st quality urinal half stall type, white colour, of size 465x355x265 mm incl providing and fixing plugs/brackets, bedding urinal against wall in CM 1:2, securing urinals to plugs with and incl S&F of all accessories for fixing as recommended by manufacturer like 60mm long brass secrews/fasteners/rag bolts etc, pointing urinal back in white cement; connecting for discharge pipe incl necessary packing, union complete all as specified.

S&F in repair Urinal spreader of PTMT any colour for fixing with 15mm dia pipe. (Minimum weight 60gms).

S & F in repair Vitreous china premium/1st quality wash basin (under counter), white, size 550x400 mm including S&F all accessories as recommended by manufacturer complete fixed in position in all respect as per manufacturer's instructions and all as specified including all Waste fittings, brass,chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, Note : The items for counter will be measured and paid separately.

S & F in repair Flushing cistern of PVC 10 ltr. cap. with dual flushing system, valveless syphonic action type, , low level, white/ivory/off white with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete in all respect all as specified.

S&F in repair PVC connection 15mm bore length not less than 450 mm long with both ends PTMT nuts complete all as specified.

S&F in repairs chromium plated swivel shower roses with or without swivel joints, for fixing with 15mm pipe fixed all as specified

S&F in repairs tubular towel rail, brass cromium plated, 20mm dia, D type, 60cm long between flanges complete all as specified and directed Engrs-In Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding, removing serviceable tiles to stores and removing debris outside the MD land.

S&F Non-Skid ceramic Coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4 complete all as specified.

S&F Non Skid Ceramic tiles 7 to 8 mm thick in light shed ,area of each tiles exc 0.18 sqm but not exc 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4, complete all as specified and directed

Ditto as item above but as in skirting over cement mortar backing plaster in CM1:4 15mm thick

M&L for Glazed ceramic glossy finish tiles coloured in vertical surface 450X300X7mm in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar. Note : Work will be in patches or in bulk

Demolition of cement Concrete is ground floors andy pavings n exc 15 cm thickness (below or above ground level), complete all as specified and directed

M&L for 25mm thk PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in subbase of floors & finishing the surface even & smooth without using extra cement.

M&L 100mm thick cement concrete type D-2, 1:4:8 (40mm graded crushed stone aggregate) finishing cement concrete surface even and smooth without using extra cement as specified and directed.

M&L for 40mm thk PCC 1:2:4 type B1 using 20mm graded stone aggregate as in subbase of floors & finishing the surface even & smooth without using extra cement.

M&L PCC (1:2:4) type B-1 (using 20mm graded stone aggregates) as in coping,benching/channels of manholes including demolition of existing pcc etc complete all as specified and directed

M&L for 75mm thick plain cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection finished even and smooth without using extra cement, including making joints to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:2 by weight complete all as specified and as directed.

Demolition for ( Rcc jhali)ashlar facings,dressed stonework,precast concrete articles and precast concrete block walling complete all as specified and directed

M&L for providing precast cement concrete louvres and jallies incl RCC pillars as directed by Engr-in-charge, of type B0 1:2:4 (12.5MM GRADED AGGREGATE) set in cement mortar 1:4, of 40mm thick (measured solid), including all mould-ings but excluding frame (pre cast frame shall be measured separately and paid for under item 4032) and applying two coat of cement based paint over a coat of primer complete all as specified and directed. complete all as specified and directed

M&L for 10 mm rendering in CM 1:4 on fair face of brick work or on concrete surface incl Chajja/Facia etc finished even and fair with water profinfing compound (WPC) complete all as specified and directed.(WPC Measured seprately)

M&L for 15 mm rendering in CM 1:4 on stone masonry suravce or surface other than fair face of vrickwork or on one side of lathing with water profinfing compound (WPC) complete all as specified and directed.(WPC Measured seprately)

M&L for preparation of new plastered surfaces of external walls/RCC surfaces/soffits of chajjas/roof projection/cantilivers/balcony etc including cornices and applying two coat of cement base paint as camouflage / ordinary pattern pattern over a one coat of of external primer.complete all as specified & as directed by engr-in-charge.

M&L for complete removal of existing treatment of any type/description such as cement base paint,external emulsion etc from external surfaces of walls/RCC surfaces/soffits of chajjas/roof projections/cantilivers/balcony etc with mechanical means/grinder and preparing existing treated surfaces of external walls/RCC surfaces/soffits of chajjas/roof projection/cantilivers/balcony etc including cornices and and fill the crack of wall with crack filler paste and applying two coat of cement base paint as camouflage / ordinary pattern over a coat of primer by complete all as specified & as directed by engr-in-charge. Note for above items of external finishing :- the cost for steel tubular double scaffolding necessary for execution of work and protective measures for height more than height of double storey building as directed by engr-in-charge shall be included in the quoted rate against the respective item and nothing shall be admisible for this.

Demolition of cement concrete ( unreinforced) in roofs , floors (other than ground floors) beams, staircases,landing, chajjas and similar suspended work

M/L plain cement concrete 1:2:4 type B-0, using 12.5 mm graded aggregate as in roof for maint. the uniform slope etc any thickness at any height and in any position all as specified and directed by engr-in-charge at site.

M&L Applying evenly a coat of bituminous primer confirming to IS 3384 - 1986 @ 0.40 Kg/Sqm

M&L APP based polymeric membrane minimum weight 3 Kg/Sqm and minimum 3 mm thick reinforced with polyster non wove fabric (wt not less than 150 gms/Sqm) land on primed surface by forced application complete all as specified

S&F for Cement concrete tiles 20cm x 20cm x 20mm thick, ma c h i n e pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished on terraace/roof surface over 15mm thick screed bed in CM 1:4 set and jointed grouted and flush pointed complete all as specified and directed. (WPC Measured seprately)

Supply only liquid water proofing compound ( For external new plaster surfaces)

Taking down chowkat or frames area not exc1.5 Sqm each and refix. complete all as specified and directed.

S&F in repair stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or stainless steel wire staples or with wooden beads, stainless steel screws and nuts bolts etc for ventilator complete all as specified.

M & L for rolled mild steel work frame work as in doors /windows/ vent/gates ,angle or other section with gusset plates , rails, braces, etc complete drilled welded to frame and shutter, four Nos lugs welded to frame inculding necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4 type B-1 including synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured & paid separately under respective items for fixing and confirming to Fe-410W (Gde E-250 quality 'A') complete all as specified and directed.

Repairs to structural members like columns, beams, slab by removing the corrosion from reinfrocement and applying one coat of nito zinc primer or equivalent to renforcement and applying one coat of NITOBOND SBR or equivalent to old concerete and applying cement concrete 1:1.5:3 using 6mm aggregate and approved Fosroc or equivalent chemical for additional strength including necessary formwork as required the thickness of concrete is 15mm to 50mm as per requirement at site (Nitobond EP & Nitobond SBR)

M&L for servicing of magzine and ESH iron door (any size), making it operational including application of greas, cleaning of sliding channel, making good defective parts like wheel, hinges, iron frames sliding channels as required, including welding as required, maintaining slider door or openeable door to operative condition including making good of distrubed adjoinning plastered/unplastered surfaced of wall as brick/stone work/PCC etc, throughtout the period of contract complete all as specified and directed. (Note: Unit rate quoted against this item shall deemed to be inclusive of all the above provision per unit i.e. each shutter and shall be assumed to be inclusive of arrangement for fixing magazine/ESH doors by engaging cranes (Hydraulic)/ manual methods as per site requirement.

Demolition of Brick or Stone Masonry built in cement mortar etc complete all as specified and directed.

M&L for walling Random rubble masonry uncoursed well bonded bedded and solidly hearted and built in cement mortar 1:4 etc complete all as specified and directed.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, with maximum depression on face from straight edge held against the dressed surface n exc. 20 mm of random rubble walling of sand stone, uncoursed or brought upto courses

M & L for 15mm thick rendering on stone masonry surface ,in (CM 1:4,) finished fair and even without using extra cement including neeru finish to plastering complete all as spfd and directed.

M&L PCC 1:2:4 (Nominal mix) type B-1 using 20mm graded aggregate as in surface channel and drain all as specified.

M&L cement concrete type D-2, 1:4:8(40 mm graded aggregate), 100 mm thick, complete all as specified and directed.

Extra for fair finishes drain or channel 30cm and over in girth in C. conc using extra cement including forma mounds metred/stopped ends etc.

Taking down old, unsv aluminium/copper point wiring (light, fan, socket or power) complete, incl fixture & fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit & making good the disturbed surfaces of walls, floors, etc. complete all as specified and directed by Engr-in-Charge.

Taking down old sub-main wiring incl fixture & fittings etc. removing materials to store for keeping in safe custody or for taking credit & making good the disturbed surfaces of walls, floors, etc. complete all as specified and directed by Engr-in-Charge.

Disconnecting/dismantling of old existing un serviceable DB's along with metal enclosue concealed in walls of any type/way 240/415 Volts with their old/un serviceable burnt MCCB/MCB's etc.incl making good the disturbed surfaces and matching with existing surfces complete all as specified and directed by Engr-in-Charge. NOTE for Item Nos 85 to 87 : Cost of making good the disturbed surfaces is deemed to be included in the unit quote rates.

M & L for concealed point wiring with two single core 1.5 sqmm PVC insulated, unsheathed, FRLS cable, 1100 volts grade, ISI marked with multi stranded copper conductor drawn through and including non-metallic PVC rigid conduit (medium grade) with all fittings and accessories ISI marked incl provision of 1.5 sqmm PVC insulated, multistranded, unsheathed, copper conductor cable, FRLS, ISI marked as earth continuity conductor (green in colour) & incl fixing of modular metal flush boxes of appropriate size & thickness fixed flush to wall for mounting switch, sockets etc. with including cutting chases for conduits & sinkings for modular boxes & making good the disturbed surfaces, matching to the existing one etc. complete all as specified & as directed for the following (a) One Light/fan/Call Bell etc. point controlled by one switch 5/6 Amps. NOTE : 1) Modular metal flush boxes shall be measured & paid separately. 2) Cutting chases & making good the disturbed surfaces is deemed to be included in the unit quoted rates.

All as per Item No-88.00 here-in-above, but One switch socket outlet point 5/6 Amps on Same board.

All as per Item No-88.00 here-in-above, but One switch socket outlet point 5/6 Amps on independent board.

All as per Item No-88.00 here-in-above, but with FRLS PVC insulated copper conductor cable of size 2.5 Sqmm and 2.5 Sqmm for earth continuity conductor green in colour for 16A switch socket complete.

M & L for concealed sub-main wiring alongwith earth wire of size (2 x 4.00) sq. mm + (1 x 4.00) sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including non-metallic PVC conduit (medium grade) with all fittings and accessories ISI marked for conduits & sinkings for modular boxes & making good to walls, floors,ceiling etc. complete all as specified & as directed. .NOTE : 1) Two runs of PVC wire, one run of earth wire & one run of PVC rigid conduit (medium grade) will be measured as one length. 2) Modular metal flush boxes (if req) shall be measured & paid separately.2) Cutting chases & making good, including necessary Putty work of the disturbed surfaces is deemed to be included in the unit quoted rates.

S & F Modular switch, one way, 6 Amp, 1 Module, 240 volt complete all as specified and as directed. NOTE for Item Nos 93 to 102 : The make/model of modular metal flush boxes & modular cover plates shall be same as that of modular switches & sockets.

S & F Modular switch with indicator, one way, 16 Amp, 1 Module, 240 volt complete all as specified and as directed.

S & F Modular shuttered socket outlet 3 Pin, 6 Amp, 2 Module, 240 volts, ISI marked complete all as specified and as directed.

S & F Modular shuttered socket outlet 3 Pin, 6/16 Amp, 2 Module, 240 volts, ISI marked complete all as specified and as directed.

Supply & Fixing and concealing modular metal flush box suitable for fixing switches/sockets of 1/2 modules all as directed.

Supply & Fixing and concealing modular metal flush box suitable for fixing switches/sockets of 3 modules all as directed.

Supply & Fixing and concealing modular metal flush box suitable for fixing switches/sockets of 12 modules all as directed.

Supply & Fixing modular cover plate suitable for fixing switches/sockets of 1/2 modules all as directed.

Supply & Fixing modular cover plate suitable for fixing switches/sockets of 3 modules all as directed.

Supply & Fixing modular cover plate suitable for fixing switches/sockets of 12 modules all as directed.

S&F ceiling rose surface PVC/ Polycarbonate, Isolated body with face Bakelite three terminal complete all as specified and directed.

S&F IP>=20, Class I Wall mounted 4 feet LED batten with integrated electronic driver & Aluminium body complete with all accessories, prewired, including 20 W with min 120 lumens/Watt output,6500 K, LED 4 feet tube light and connecting of flexible wire twin core from ceiling rose to fitting through & including flexible conduit from ceiling rose to fitting complete incl taking down old/unsv fittings all as specified and directed by Engr-in-Charge.

S&F IP>=20, Class I Wall mounted 2 feet LED batten with integrated electronic driver & Aluminium body complete with all accessories, prewired, including 10 W with min 120 lumens/Watt output,6500 K, LED 2 feet tube light and connecting of flexible wire twin core from ceiling rose to fitting through & including flexible conduit from ceiling rose to fitting complete incl taking down old/unsv fittings all as specified and directed by Engr-in-Charge.

S&F IP >= 65,IK>=07, Class I Environment friendly, energy saving, surface mounted, decorative bulk head edge lit LED luminaire 10W with min 120 lumens/watt output made of pressure die cast aluminium housing with suitable fixing arrangement complete with all accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable of suitable size complete incl taking down old/unsv fittings all as specified and directed by Engr-in-Charge.

S&F IP >= 65, IK>=07, Class I energy saving and environment friendly long life high power LED as source of building security light of 30W with min 110 Lumens/Watts, made up of pressure die cast aluminum housing with acrylic cover as diffuser with including GI pipe bracket made out of 40mm dia light grade pipe of length 1.2 Mtrs, bend to shape 120-130 degree and MS clamps made out of 25x3mm flat iron 2 Nos including nut and bolts for fixing the bracket and making connections through & including flexible conduit from ceiling rose to fitting complete incl taking down old/unsv fittings all as specified and directed by Engr-in-Charge.

Supply, install, testing & commissioning of Exhaust fan, metal body with automatic back shutter louvers 300 mm sweep, 1400 RPM or more, Air Delivery not less than 1850 CMH, single phase, 240 Volts, AC, 50 Hz and connecting up complete including louvers and provision of cable 3/2 core of suitable size from ceiling rose to fan in flexible hose and making of suitable sized hole in the wall/existing window/ventillator etc. for fixing of the exhaust fan & making good the disturbed surfaces (if any) complete all as specified & as directed. Note :- (i) The cost of making hole in walls/other surfaces & making good the disturbed surfaces incl any framework/cement work/wood work/welding work etc. required for proper fixing of the exhaust fan & matching to the existing surface is deemed to be included in the unit quoted rates.

Supply and Fixing ceiling fans complete with blades, down rods of suitable lengh upto Ceiling/false ceiling level, with fan regulator 2M and accessories, 230 V, 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE Five star rating with Brushless direct current rating (BLDC) including connecting up with and including twin/three core twisted flexible copper conductor cable of suitable size complete all as specified and directed by the Engr-in-Charge incl taking down old/unsv fan. Note : (i) Installed Ceiling fan's warranty card should be submitted to the Engr-in-Charge. (ii)The cost of making good the disturbed surfaces and matching to the existing/original surface is deemed to be included in the unit quoted rates (iii)The cost of taking down old unserviable Ceiling fan's and tranportation of old Ceiling fan's to be submitted to MES Store yard is deemed to be included in the quoted rate.

S & Fand concealing SPN DB, 04 Way, IP43, IK09, Metal double door type 240 volts fitted with busbar and blanking plates, neutral link and making good the disturbed surfaces with all other accessories including necessary connection all as specified and directed by Engr-in-Charge.

S & F and concealing SPN DB, 08 Way, IP43, IK09, Metal double door type 240 volts fitted with busbar and blanking plates, neutral link and making good the disturbed surfaces with all other accessories including necessary connection all as specified and directed by Engr-in-Charge.

S&F Miniature circuit Breakers, SPN,C-Series 240 Volts of capacity 6-32 Amps with breaking capacity 10 KA all as specified and dircted by Engr-in-Charge.

S&F Miniature circuit Breakers, single pole,C-Series 240 Volts of capacity (6-32 Amps) as ordered with breaking capacity 10 KA all as specified and dircted by Engr-in-Charge.

Supply, laying, jointing & testing XLPE insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6 sq mm 2.0 core in trenches / through GI pipe / fixed along with pole structure etc with all fixing & connecting accessories like Lugs, Gland etc incl taking down old existing Cable of any size/type complete all as specified & as directed.

Supply, install, testing & commissioning of LT busbar junction box "out-door type" of size 600 mm (height) x 600 mm (breadth) x 300 mm (depth) (minimum dimensions), factory fabricated CPRI approved (type-tested) with suitable neoprene rubber gasket to make it completely dust & vermin proof & degree of protection not less than IP-55 & general construction confirming to IS-13947, double door, front & back openable. The box shall be provided with ventilation facility in the form of louvers for better heat dissipation & high grade Copper bus-bar of Size 300mm x 20mm x 3mm , min spacing of 75mm between the busbars & wrapped with coloured PVC tape /sleeves of rating in conformity to the Incoming cable rating. The panel board shall be fabricated out of 3.15 mm thick (for outer portions) & 2.00 mm thick (for inner portions) CRCA sheet duly pre-treated & powder coated, supporting angle iron frame of size 50X50X6mm fixed at 75 cm height from groud level & MC channel base suitable for 3 Phase, 4 wire system 415 /440 volts grade including I/C & O/G cable opening on bottom & at both sides including cable glands of suitable sizes with suitable PCC (1:3:6) type C-2 foundation , necessary earthwork (if any) incl Incoming MCCB of 63 Amps in seprate portion complete all as specified & as directed.

S&F in repairs/replacement of flame proof SPN 8 Way Enclosure Size (330X350X190mm) FLP/WP Lighting Distribution Panel Incoming: MCB,2P,32A- 1 No. Outgoing: MCB,1P,6-32A- 6 Nos. with complete internal bus bar & wiring up terminals incl taking down old Unsv complete all as specified and as directed

S&F in repairs/replacement of flame proof TPN 4 Way Enclosure Size (390X390X190mm) FLP/WP Lighting Distribution Panel Incoming: MCB,4P,63A- 1 No. Outgoing: MCB,1P,6-32A- 12 Nos. with complete internal bus bar & wiring up terminals incl taking down old Unsv complete all as specified and as directed

M&L for Air termination, single pointed, Aluminium rod 12mm dia, 300mm long fixed with roof in and including all fittings, fixtures shaddles, insulators, etc including taking down unsv Air terminantion rod of any size complete all as specified and directed.

S&F aluminium stip 25mm x3.15mm fixed with saddles & fixing screws of size not less than 4mm dia , 32mm long for roof conductors and down conduxctors above ground level with porcelin insulators of 15 BMD size 'T' type placed not more than 50cm apart with screws/nut/bolts etc including taking down unsv Aluminum Strip of any size/type complete all as specified and directed.

S&F in replacement of test point terminal block made of phasphorus broze size 75x75x25mm, drilled and screwed including 3 nos. 8mm dia, 25mm long hex head screw incliding test point Enclosed in fiber box of size 125x125x50mm fixed on wall incl taking down old Unsv one complete all as specified and directed.

S&F in replacement of galvanized iron strip of size 32x6 mm incl saddles /supporting insulators to run over the roof/wall or drawn in conduit/pipe or fixed to poles/wall or any other indicated situation incl taking down old existing earth strip complete all as specified and directed by Engr-in-charge.

M&L for Earth continuity conductor fixed to wall or recess or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 32x6mm galvanised iron strip incl taking down old existing earth strip complete all as specified and directed by Engr-in-Charge.

Supply and fixing in replacement of GI tubing 40 mm dia light grade with all fittings for protection of GI strip burried in ground depth not less than 30 cm and grouting at PCC Foundation in cement concrete complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of GI tubing 50 mm dia light grade with all fitting for protection of GI strip and fixed complete to walls and ceilings or grouting at PCC Foundation in cement concrete complete all as specified and directed by Engineer-in-Charge.

M&L for earthing complete with Galvanised steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (in vertical position) earth pit not less than 2.25 mtr below normal ground level with the top edge of the earth plate not less than 1.5 mtr (B.G.L.) and connected to GI earth strip 32 x 6 mm by means of bolts, nuts, check nuts, and washers of galvanized iron including PCC pit & cover with suitable handle, including necessary excavation and earth work in any type of soil, 20 mm dia med grade galvanized steel tube for watering with one end fixed with suitable funnel and wire mesh, 40 mm bore Medium grade galvanized steel tubing for drawing earth lead GI strip protection & common salt, charcoal in alternate layers etc. complete all as shown in EP No 3 of SSR Part 1 and testing on completion complete incl taking out old u/s earthing all as specified and as directed by the Engr-in-Charge/GE.

M & L for bore well earthing by drilling bore with bore machine for lightening protection system using GI pipe heavy duty 50 mm dia as earth electrode driven up to a depth of 50 meters below ground level, duly made holes at 20 cm intervals, along the length of GI pipe and providing the charcoal salt mixture incl GI pipe 150 mm dia Medium grade as protection upto a depth of 12 meters and GI strip of 32x6 mm so as to acheive desired earth results. Testing and commissioning complete. (Earth strip of size 32x6mm upto a length of 7.5m is deemed to incl in this item rate).