PROVISION OF 01 X ELEVATED SENTRY POST FOR (02 X GUARD CDR AND 06 SENTRIES WITH LIVING ACCN AND TOILET) 977 AD REGT WKSP AT KALINA, MIL CAMP MUMBAI, SPL REPAIR / REPLACEMENT OF CEILING FAN AGAINST BER CEILING FANS AT VARIOUS LOCATIONS UNDER GE (N) SA

Amount

M&L for surface dressing n exc 30cm and averaging 15cm deep in soft / loose soil including cutting of grass and small trees etc complete all as specified and as directed by Engineer-in-Charge.

M&L for surface dressing n exc 30cm and averaging 15cm deep in hard/dense soil including cutting of grass and small trees etc complete all as specified and as directed by Engineer-in-Charge.

Excavation over areas n. exc 1.5 m in deep and getting out in any type of soil and removal outside MD land complete all as specified and as directed by Engr-in-Charge

Material and labour for excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in deep for foundation , getting out in hard/dense soil or soft disintegrated rock complete all as specified and as directed by Engineer-in-Charge

Material and labour for Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in deep for foundation,or pole or laying of cable,pipe laying pipes etc or for shaft, walls, manholes, pier holes etc not exceeding 10 sqm on plan and not exceed 1.5m in depth and getting out in hard/dense soill complete all as specified and as directed by Engineer-in-Charge

Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed by Engineer-in-Charge

Removing excavated soil to a distance exceeding exc 250m but n exc 500m and depositing where directed outside MD land complete all as specified and as directed by Engr-in-Charge.

Removing excavated soil to a distance exceeding 1.5 Km but not exceeding 5 Km and depositing where directed outside MD land complete all as specified and as directed by Engineer-in-Charge.

Returning, filling in including spreading, leveling, watering and well ramming soil in layers n.exc 25 cm thick complete all as specified and as directed by the Engineer-in-Charge

Material and labour for Plain Cement Concrete 1:4:8 type D2 using 40mm graded stone aggregate as in foundation / mass concrete/filling complete all as specified and as directed by the Engineer-in-charge

Material and labour for Plain Cement Concrete 1:2:4 type B1 using 20mm graded stone aggregate as in coping including necessary formwork for fair finished surfaces etc complete all as specified and as directed by the Engineer-in-charge

Material and labour for Plain Cement Concrete 1:3:6 type C2 using 40mm graded stone aggregate as in foundation, footing, bases of columns, raft and raft beams, plinth beams, mass concrete and similar work etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Pre-cast cement concrete block masonry 1:3:6 type C1, (using 20mm graded stone aqggregate), with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge.

M & L for cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate), as bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in, bore of pipe 150mm bore of pipe complete all as specifed and directed

M & L for salt glazed stoneware drain pipes of grade 'A' laid in trenches and jointed with cement mortar (1:1) with spun yarn of dia 150mm complete all as specified and as directed by Engr-in-Charge.

M & L for extra for forming fair finished drain or channel 30cm inner girth in cement concrete with using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and as directed.

Material and labour for rendering 5mm thick in cement mortar 1:4 with water proofing compound over 10mm thick in cement mortar 1:6 on fair faces of concrete surfaces of ceiling and finished even and fair without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed by Engineer-in-Charge.

Material and labour for providing Anti-termite Treatment with treating the bottom and sides of excavation surface of filled earth chemical emulsion at the rate of 5 litre per square metre including drilling and plugging holes etc in apron complete all as specified and as directed by Engineer-in-Charge.

Material and labour for providing and injecting chemical emulsion for Anti-termite Treatment on backfill in contact with foundation at the rate of 7.5 litres per square meter of vertical surface area (area of the substructure in contact with backfill to be measured ) complete all as specified and as directed by Engr-in-Charge.

Material and labour for providing and injecting chemical emulsion for Anti-termite Treatment on top surface of filled earth at the rate of 5.0 litres per square meter complete all as specified and as directed by Engr-in-Charge.

Material and labour for providing and injecting chemical emulsion for Anti-termite Treatment under plinth protection at the rate of 5.0 litres per square meter complete all as specified and as directed by Engr-in-Charge.

Material and labour for providing Anti-termite Treatment with treating soil along with external perimeter with chemical emulsion at the rate of 2.25 litre per linear metre including drilling and plugging holes etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for post construction Anti-termite Treatment along the external wall where the apron is not provided using chemical emulsion @ 7.5 litres per Sqm metre of the vertical surface of the sub structure to a depth of 300mm including excavating channel along the wall and rodding etc complete all as specified and as directed by Engineer-in-Charge. .

Material and labour for 40mm thick Plain Cement Concrete 1:4:8 type D2 using 40mm graded stone aggregate as in Damp Proof Course, mixed with water proofing compound complete all as specified and as directed by the Engineer-in-charge. Note: water proofing compound shall be measured & paid seprately

Material and labour for Plain Cement Concrete 1:2:4 type B1 using 20mm graded stone aggregate as in Damp Proof Course, mixed with water proofing compound complete all as specified and as directed by the Engineer-in-charge. Note: water proofing compound shall be measured & paid seprately

Supply only integral water proofing compound ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Pidilite Industries Ltd, Taloja /Super Aquacem (India) Ltd /FOSROC/Siko/Dr Fixit

Material and labour for walling random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge.

Material and labour for old brick work with sub class 'B' bricks, straight or curved on plan, exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

M&L 75mm hardcore broken stone or boulders of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface at transformer yard complete all as specified and directed by Engr-in-Charge.

Material and labour for 40mm thick & 750mm wide cement concrete (1:3:6) type C2, using 40mm graded stone aggregate as in plinth protection and finishing the surfaces even and smooth without using extra cementcomplete all as specified and as directed by Engineer-in-Charge.

Material and labour for 75mm thick cement concrete (1:3:6) type C2, using 40mm graded stone aggregate as in plinth protection and finishing the surfaces even and smooth without using extra cementcomplete all as specified and as directed by Engineer-in-Charge.

Material and labour for 25 mm thick cement concrete (1:2:4) type B1 using 20 mm graded stone aggregate as in flooring, path/hardstanding and finishing the surface even and fair without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 75mm thick Plain Cement Concrete 1:4:8 type D2, using 40mm graded stone aggregate as in sub base of flooring/ hard standing/path and finished even and fair without using extra cement etc complete all as specified and as directed by Engineer-in-Charge

Material and labour for machine cut Kota stone slab flooring 20-25 mm thick over and including cement screed bed 15 mm in Cement Mortar (1:6) base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

All as per item No.35 described here-in-before but 20-25mm kota stone as in riser of steps, skirting, dados etc laid over cement screed and jointed complete all as specified and as directed by Engineer-in-Charge.

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or colour cement to match over and including screed bed of 20mm thick in Cement mortar 1:4 etc complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / RAK tiles/ Orient bell

Material and labour for non skid joint free coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or colour cement to match over and including screed bed of 15mm thick in Cement mortar 1:6 etc complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / RAK tiles/ Orient bell/Orient bell

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or colour cement to match over and including screed bed of 15mm thick in Cement mortar 1:6 etc complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / RAK tiles/ Orient bell/Orient bell

Material and labour for coloured glazed ceramic tiles of size 300mm x 200mm x 7 mm thick, on vertical surfaces etc, set and jointed in neat cement slurry and pointed in coloured cement to match including 12mm thick backing coat in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell / M/s RAK tiles

Material and labour for coloured glazed ceramic tiles of size 300mm x 200mm x 7 mm thick, on vertical surfaces etc, set and jointed in neat cement slurry and pointed in coloured cement to match including 10mm thick backing coat in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell / M/s RAK tiles

Material and labour for machine pressed cement concrete tiles 300 x 300 x 20mm thick with grey cement and no pigments, set, jointed and pointed in neat cement slurry in floors including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge. Make- (a) M/S Mehatab Tiles, Indore (b) National Tiles(c) Bharat Tiles and Engg Coy, Bangalore (d) Modern Tiles and Marbles Bangalore (e) M/s NITCO, Mumbai (f) Ultra (g) Duracrete

Material and labour for 10 mm thick rendering in cement mortar (1:4) on brick/concrete surfaces & finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 10 mm thick rendering in cement mortar (1:6) on brick/concrete surfaces & finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for renderingin two layers 12mm thick plaster in cement mortar (1:4) on other than fair faces of brick work or cement concrete surfaces mixed with waterproofing compound @ 3% by weight of cement or as per manufacturer's instructions and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Note: waterproofing compound shall be measured and paid separately

Material and labour for renderingin two layers 15mm thick plaster in cement mortar (1:4) on other than fair faces of brick work or cement concrete surfaces mixed with waterproofing compound @ 3% by weight of cement or as per manufacturer's instructions and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Note: waterproofing compound shall be measured and paid separately

Material and labour for rendering 5mm thick in cement mortar 1:3 on ceiling and finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of newly plastered internal wall surfaces and applying two coats of oil bound distemper with roller over a coat of alkali resistant wall primer complete all as specified and directed by Engineer in Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints/Berger paints

Material and labour for preparation of new plastered surfaces of wall/ floor surfaces & applying two coats of cement based paint complete all as specified and as directed by Engineer-in-Charge. Make : Snowcem/Duracem/Aquacem/Berger/Shalimar

Material and labour for preparation of newly plastered ceiling surfaces and applying three coates of white wash complete all as specified and directed by Engineer in Charge.

Material and labour for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper with roller over a coat of alkali resistant wall primer over 1.5mm thick layer of wall care putty complete all as specified and as directed Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints/Berger paints

Supply and fix factory pressed steel frames made out of mild steel black sheet 1.25mm thick of profile 165 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, including shop coat of primer and threshold of 12mm dia round bar 1 No welded at bottom of frame etc.,with PCC type C0 1:3:6 using 12.5mm graded crushed stone aggregate complete all as specified and as directed Make:M/s Madhu Industries, Jangid Engineering Jaipur, Decan Structural Pvt Ltd Bangaluru, Chandni Industries, Ashwani & Sons, Anoop Industries,Trisul Industries, Ashish Industries

Supply and fix stainless steel butt hinges, medium weight, 100mm size all as specified and directed. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminium anodised barrel tower bolt of extruded section size 200mm complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix extruded aluminium alloy handles fabricated types, anodised, of size 150 mm long complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminum anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy 300mm long, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix 300mm long mild steel ordinary rat rail rod pattern springs including roller and roller plate complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 15 micron coloured powder coated aluminium sections for sliding (3 Track) or openable windows, ventilators, doors, partitions etc including fabrication of frame & shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc including all accessories such as glazing clips and rubber beadings for fixing glass panes / wire mesh in frame complete all as specified and as directed by Engineer-in-Charge. Make : Hindalco/Indal (Indian Al Coy)/Jindal/Associated Profile & Aluminium Ltd/Ajit India Note: (i) Glass panes /wire mesh will be measured & paid separately. (ii) Rubber beading will not be weighed.

Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of M. S. tubes for top & bottom rails. M.S. frame shall be covered with heat molded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at site as per specification & drawing on Serial Page No 149 & 176 of SSR Part II (pertaining to item No 08080) including necessary aluminium builders hardware for one door to be provided such as 100mm dia butt hinges - 3Nos, tower bolt 200mm dia - 2Nos, handle 200mm long - 2 Nos etc complete all as specified and as directed by Engineer-in-Charge. Make: M/S RajshriPlastiwood, Indore (Rajshri)/ M/S Sintex Industries Ltd (Sintex)/ M/S Accura Polytech (Accucel)/ M/S Dura Plast Extrusion (Duraplast)/ M/S Madhu Industries (Madhu Industries)/ M/S Navratna Co Speciality Chemicals(GIZA)

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with 19mm x 19mm MS square tube EPDM rubber gasket weather seal to be provided through the frame, the profile shall be mitre cut at two corners and jointed by inserted 2mm of 150mm long bracket of 15mm x 15mm MS square tube inside the 19mm x 19mm MS square tube and suitable screwed the door frame shall be fixed to the wall using PVC fasteners. A minimum of 6 Nos screws to be provided for each frame as per specification & drawing on Serial Page No 180 of SSR Part II (pertaining to item No 08095) all as specified and as directed by Engineer-in-Charge. Note: The quoted rates are deemed to be included for cutting holes, providing concrete for hold fast and making good to the disturbed surfaces. Make: M/S RajshriPlastiwood, Indore (Rajshri)/ M/S Sintex Industries Ltd (Sintex)/ M/S Accura Polytech (Accucel)/ M/S Dura Plast Extrusion (Duraplast)/ M/S Madhu Industries (Madhu Industries)/ M/S Navratna Co Speciality Chemicals(GIZA)

Supply and fix 35mm thick factory made plain framed panelled shutter 2nd class hardwood rail and style (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces, the size of rail and stile as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in-Charge. Make : M/s Goel Brothers, Raipur / M/s Pioneer Timber, Chandigarh / M/s Goyal Industries, New Delhi / M/s Jain Doors pvt Ltd, Haryana / M/s India Wood & Wood Pdts, Mangalore / M/s MP Wood Products, Indore / M/s A1 Teak Products, Indore / M/s Jain Wood industries( Brand : JAYNA)

Supply and fix plain solid straight chowkats, second class hardwood, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints including making good frame in cement concrete complete all as specified and as directed by Engineer-in-Charge.

Material and labour for MS framed work such as grills , gratings, brackets of chajja etc with ends of bars shouldered and /or riveted or forged into spikes, framed guard bars, framed work of garbage bin, barred iron doors, ladders, framed balusters, walk ways, railings, framework of watertanks and similar work conforming to FE 290 Gde 165 etc. complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to conforming to Fe-410-W (Gde-E-250) quality-B complete all as specified and directed by Engineer in charge.

Supply and fix 35mm thick factory made 2nd class hard wood glazed and skelton shutter, open rebated, prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutter as specified in SSR Part-I section 8, clause No 8.24 (b) complete all as specified and as directed by Engineer-in-Charge. Make : M/s Goel Brothers, Raipur / M/s Pioneer Timber, Chandigarh / M/s Goyal Industries, New Delhi / M/s Jain Doors pvt Ltd, Haryana / M/s India Wood & Wood Pvts, Mangalore / M/s MP Wood Products, Indore / M/s A1 Teak Products, Indore / M/s Jain Wood industries( Brand : JAYNA)

Supply and fix mild steel TMT bars, 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

Ditto all as per item no.66 above but 5mm dia and over up to incl. 10mm dia in stirrups, spaces and binders complete all as specified as directed by Eng-in-charge.

Material and labour for providing precast reinforced cement concrete, 1:2:4, type B-1 (using 20 mm graded stone aggregate) for manhole / drain covers etc., set in cement mortar 1:4 and finishing the exposed faces even and smooth without using extra cement including necessary form work for fair finished surfaces complete all as specified and as directed by Engineer-in-Charge. Note : Reinforcement shall be measured and paid separately.

Material and Labour for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter for rough finished surfaces complete all as specified and as directed by Engr-in-Charge.

M&L for Formwork to sides of pillars, posts, struts, piers, columns, etc. for rough finished square or rectangular surfaces of concrete complete all as specified and as directed by Engineer-in-Charge.

M&L for Formwork to sides and soffits of floor or roof beams, cantilevers, bressummers, etc. for rough finished flat surfaces of concrete complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for Formwork to soffits of suspended slabs such as floor slabs, roof slabs, landings and similar work not exceeding 200mm thick (horinzontal or sloping) for fair finish surface of concrete complete all as specified and as directed by Engineer-in-Charge.

Material and labour forl formwork to chullah hoods, chajjas, troughs and similar items including edges not exceeding 200mm thick for rough finished surfaces of concrete complete all as specified and as directed by Engineer-in-Charge

Material and labour for reinforced cement concrete M-30 (design mix) (using 20mm graded stone aggregate) as in foundation, footing, bases of columns, raft and raft beams, plinth beams, mass concrete and similar work etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour forreinforced cement concrete M-30 (design mix) (using 20mm graded stone aggregate) sides of pillars, posts, struts, piers, columns, etc. for rough finished square or rectangular surfaces of concrete complete all as specified and as directed by Engineer-in-Charge.

Material and labour for reinforced cement concrete M-30 design mix as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for Reinforced cement concrete of M-30 design mix using 20mm graded stone aggregate as in chajja including attached pilasters and buttresses and similar work complete all as specified and as directed by Engineer-in-Charge

Material and labour for Reinforced cement concrete of M-30 design mix using 20mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span and similar work complete all as specified and as directed by Engineer-in-Charge

Supply and fix galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with aluminium wire staples complete all as specified and as directed by Engineer-in-Charge

Supplying and laying CPVC pipes, heavy duty, SDR 11 of outer diameter 16mm & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors with suitable fixing clamps/ fastners including taking down existing pipes complete all as specified and as directed by Engineer-in-Charge. Make- FINOLEX/ Dutron/ SFMC/ Birla Aerocon/Astral

Supplying and laying CPVC pipes, heavy duty, SDR 11 of outer diameter 20mm & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors with suitable fixing clamps/ fastners complete all as specified and as directed by Engineer-in-Charge. Make- FINOLEX/ Dutron/ SFMC/ Birla Aerocon/Astral

Supplying and laying CPVC pipes, heavy duty, SDR 11 of outer diameter 25mm & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors with suitable fixing clamps/ fastners complete all as specified and as directed by Engineer-in-Charge. Make- FINOLEX/ Dutron/ SFMC/ Birla Aerocon/Astral

Supply and fix mild steel tubing medium grade 15mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239 including fixed to wall / ceiling or laid in floor with suitable size GI clamps including cutting chases in brick walls pinning in if required and making good disturbed surfaces using with cement mortar 1:3 as per existing surfaces including taking down of old GI tubing with fittings complete all as specified and as directed by Engineer-in-Charge. Make: Tata/ Jindal/ BST/ Surya/ KS Engineering/ Zenith/ Swastik/ Prakash

Supply and fix mild steel tubing medium grade 20mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239 including fixed to wall / ceiling or laid in floor with suitable size GI clamps including cutting chases in brick walls pinning in if required and making good disturbed surfaces using with cement mortar 1:3 as per existing surfaces including taking down of old GI tubing with fittings complete all as specified and as directed by Engineer-in-Charge. Make: Tata/ Jindal/ BST/ Surya/ KS Engineering/ Zenith/ Swastik/ Prakash

Supply and fix mild steel tubing medium grade 25mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239 including fixed to wall / ceiling or laid in floor with suitable size GI clamps including cutting chases in brick walls pinning in if required and making good disturbed surfaces using with cement mortar 1:3 as per existing surfaces including taking down of old GI tubing with fittings complete all as specified and as directed by Engineer-in-Charge. Make: Tata/ Jindal/ BST/ Surya/ KS Engineering/ Zenith/ Swastik/ Prakash

Supply and fix overhead shower rose brass chromium plated 125 mm dia, heavy duty pattern with swivel joints, suitable for jointing to 15 mm bore steel water tubing or union complete all as specified and as directed by Engineer-in-Charge. Make :Soma / Leader / Zoloto / Jaquar

Supply and fix gun metal globe/ gate valve, 20mm bore, with iron wheel head, screwed both ends for iron pipes, ISI marked and fixed with suitable size of new union, nipple and reducer complete all as specified and as directed by Engineer-in-Charge. Make : Leader/Zoloto/Seiko/Sant/ Essco/Prayag

Supply and fix , stop valve/push cocks , cast copper alloy, chromium plated fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed by Engineer-in-Charge Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix vitreous china bowl urinal, (flat back or corner wall type) , size 465 x 355x 265 mm white (minimum), with grating and urinal for discharge pipe, waste pipe complete including providing and fixing plugs, bedding urinal against wall in CM 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around, fixing cistern with brackets, flush pipe grating and union for discharge pipe excluding flushing cistern, flush ppe and waste pipe complete all as specified and as directed by Engineer-in-Charge. Note: Fixing supply pipe to flushing cistern, trap and waste pipe shall be measured and paid seperartely Make: Parryware/Cera(Iquality)/Jaguar/Hindware/Johnson

Supply and fix flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified and as directed by Engineer-in-Charge. Make: Finolex/Prince/Kisan/Supreme/SFMC

Supply and fix PVC connection, 15 mm size 600 mm long both end socket fix complete all as specified and as directed by Engineer-in-Charge.

Supply and fix PVC (SWR) floor trap, plain with grating including jointing with solvent cement, outlet dia 75mm complete all as specified and as directed by Engineer-in-Charge. Make : Supreme/ PRINCE (Ultrafit)/ Kisan/ Finolex/ Astral

Supply and fix PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed by Engineer-in-Charge. Make :Supreme/ PRINCE (Ultrafit)/ Kisan/ Finolex/ Astral

Supply and fix tubular towel rail aluminium anodised 20mm dia, 'D' type, 60cm long between flanges fixed to walls with screws complete all as specified and as directed by Engineer-in-Charge. Make : Crown / Jindal / Essess / Swastik

Supply and fix pillar taps fancy type cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes, 15mm bore complete all as specified and directed by Engineer-in-Charge. Make : Jaquar/ Marc/ CERA/ Kohler/ Player

Supply and fix grating of PTMT (minimum weight 25gms) 100mmcluding jointing with waste pipe, fixed in cement concrete 1:2:4 type B1, Complete all as specified and as directed by Engineer-in-Charge. Make : Electro-Steel/ Kejriwal/ NECO/ Kesoram

Supply & Fix PVC waste pipe 32mm dia for wash hand basin / half stall urinals complete all as specified and as directed by Engineer-in- Charge.

Supply and fix PVC (SWR), type B, single socketed rain water/soil waste/vent pipes with rubber ring joints, 110mm dia, fixed to walls complete all as specified and as directed by Engineer-in-Charge.. Make: Supreme/ PRINCE (Ultrafit)/ Kisan/ Finolex/ Astral

Supply and fix PVC (SWR), type B, single socketed rain water/soil waste/vent pipes with rubber ring joints, 75mm dia, fixed to walls complete all as specified and as directed by Engineer-in-Charge.. Make: Supreme/ PRINCE (Ultrafit)/ Kisan/ Finolex/ Astral

Supply and fix PVC (SWR) branch piece, single (single Y) equal or unequal of any radius 110mm bore with access door etc complete all as specified and as directed. Make :Supreme/ PRINCE (Ultrafit)/ Kisan/ Finolex/ Astral

Supply and fix PVC (SWR) branch piece, double (double Y) equal or unequal of any radius 110mm bore with access door etc complete all as specified and as directed. Make :Supreme/ PRINCE (Ultrafit)/ Kisan/ Finolex/ Astral

Supply and fix in repairs PVC (SWR) bends any radius, 110mm dia. complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex/Astral

Supply and fix in repairs PVC (SWR) bends any radius, 75mm dia. complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex/Astral

Supply and fix PVC (SWR) vent cowl 110 mm dia complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex/Astral

Material & Labour for cutting into existing manholes for 150mm internal dia of pipes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B1, smooth finished and reforming benching as required complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 15mm bore bib taps, fancy type, chromium plated, cast copper alloy, with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed by Engineer-in-Charge. Make : Jaquar/ Marc/ CERA/ Kohler/ Player

Supply and fix ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed of 20 mm bore complete all as specified and as directed by Engineer-in-Charge Make : Leader/Zoloto/Seiko/Sant/GEM

Supply and fix in repair vitreous china squatting pan Orissa pattern of size 580 x 440mm white with integral foot rest, 'P' or 'S' trap front and back inlet and including connection to trap and to flushing pipe, anti syphonage pipe etc (excluding flushing cistern & flush pipe) all as specified and as directed by Engineer-in-Charge. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson

Supply and fix PVC valveless, syphonic action type low level flushing cistern 10 ltr capacity white with inlet ball valve, float and handle including brackets, flush pipe of polyethylene of low or high density or PVC 32mm dia including connection to pipe and fixing of chains and pull or lever complete all as specified and as directed. Make : M/S Johnson Peddar/ Parryware/ RAK Ceramics/ CERA

Supply and fix flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete all as specified and as directed by Engineer-in-Charge. Make: Finolex/Prince/Kisan/Supreme/SFMC

Supply and fix vitreous china wash down, white, water closet pan (pedestal pattern) with 'P' of 'S' trap (of size 465mm x 355mm x 265mm),including plastic seat cover to match with colour of WC, closed pattern with flat bottom & cover and chromium plated mild steel or aluminium anodized hinging device including connecting to trap and flushing pipe, anti-syphonage pipe etc complete all as specified and directed by Engineer-in-Charge. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson

Supply and fix vitreous china wash hand basin white flat back size 550 x 400 mm excluding taps, waste chain and plug and porcelain stopper but including CI brackets, cutting for and pinning in ends of brackets or erecting stand including 32mm bore discharge pipe with waste coupling of PTMT etc complete all as specified and as directed by Engineer-in-Charge. Make : CERA/ RAK Ceramics/ Parryware/ Hindware/ Neyveli Ceramics (Neycer)/ Jaquar/ Kajaria (KEROVIT)

Supply and fix vitreous china wash hand basin white flat back size 450 x 300 mm excluding taps, waste chain and plug and porcelain stopper but including CI brackets, cutting for and pinning in ends of brackets or erecting stand including 32mm bore discharge pipe with waste coupling of PTMT etc complete all as specified and as directed by Engineer-in-Charge. Make : CERA/ RAK Ceramics/ Parryware/ Hindware/ Neyveli Ceramics (Neycer)/ Jaquar/ Kajaria (KEROVIT)

Supply and fix rotational molded polyethylene water storage tanks 250 litres capacity with inlet connections, three layer (cylindrical or vertical with closed top) HDPE with ISI marked, hoisted and fixed in position either inside or out side of the building, including fixing accessories and connecting up pipes securing access covers etc complete all as specified and directed by Engineer-in-Charge Make : Sintex / Polycon, Jaipur / Rotex / Infra

Supply and fix rotational molded polyethylene water storage tanks 500 litres capacity with inlet connections, three layer (cylindrical or vertical with closed top) HDPE with ISI marked, hoisted and fixed in position either inside or out side of the building, including fixing accessories and connecting up pipes securing access covers etc complete all as specified and directed by Engineer-in-Charge Make : Sintex / Polycon, Jaipur / Rotex / Infra

Material and labour for preparing new wooden surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-Charge. Make : Asian Paints/ Nerolac Paints/ Dulux ( Akzonobel)/ Nippon Paint India Pvt Ltd

Material and labour for preparing new wooden surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-Charge. Make : Asian Paints/ Nerolac Paints/ Dulux ( Akzonobel)/ Nippon Paint India Pvt Ltd

Material and labour for preparing new steel surfaces of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge. Make: Make : Asian Paints/ Nerolac Paints/ Dulux ( Akzonobel)/ Nippon Paint India Pvt Ltd

Supply and fix floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring 150mm size, fixed in floor, complete all as specified and as directed. Make : Classic/ Shalimar/ CLIF/ARGET

Material & Labour for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified and as per directed by Engineer-in-Charge.

Material & Labour for applying industrial bitumen 85/25 as in sealing compound for plinth protection complete all as specified and as per directed by Engineer-in-Charge.

Material and labour for APP modified waterproofing treatment with following specification including brushing off the surface to receive the treatment to obtain the required surface complete as directed by Engineer-in-Charge :- (a) Laying of 15mm thick cement mortar screed (1:6) mixed with and including waterproofong ompound (b) Applying oil bound bituminous primer @ 0.4lit/Sqm of density 0.87-0.89Kg/lit of 250C on the prepared dry roof surface. (c) Laying minimum 3mm thick APP membrane weight not less than 3.00 kg per sqm by torch application with minimum 10cm side lap and 15cm end lap. The laying of membrane shall be got done through an authorized applicator of manufacturer of APP membrane. (d) Over the membrane provide a solar reflective bituminous aluminium paint as prescribed by manufacturer complete all as specified. Make: STP Ltd/Texsa India Ltd/IWL Ltd/TIKIDAN Note : (i) Quoted rate includes the disconnection existing tanks of any litres capacity including all fittings, setting aside (for lowering if reqd) for roof treatment & reconnecting and refixing in position including all fittings complete all as directed.

Supply and fix powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc, aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. Make : Hindalco/Indal (Indian Al Coy)/Jindal/Associated Profile & Aluminium Ltd/Ajit India Note: (i) Glass panes /wire mesh will be measured & paid separately. (ii) Rubber beading will not be weighed.

Supply and fix Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc, aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. Make : Hindalco/Indal (Indian Al Coy)/Jindal/Associated Profile & Aluminium Ltd/Ajit India Note: (i) Glass panes /wire mesh will be measured & paid separately. (ii) Rubber beading will not be weighed.

Supply and fix anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/ pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in- charge. Make: DECOGRILLE of Associated group / Royal Alum grill Pvt Ltd or equivalent make as approved by GE

Supply and fix 4.0mm thick black glass, ordinary quality, in square exceeding 0.5 Sqm in each pane, fixed in aluminium windows complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Supply and fix 4.0mm thick figured glass, pin headed type, ordinary quality, fixing with oil putty and glazing clip, in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Supply and fix Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge. Make: JINDAL / INDALCO / HINDALCO / TATA/ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets

Supply and fix Pre- painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick as per approved profile of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws or L type or J type or cranked hook bolts or as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge. Make: JINDAL / INDALCO / HINDALCO / TATA/ASSOCIATED Profiles and Aluminium Ltd / ESSAR colour coated sheets

Material and labour for rolled mild steel sections as in joist, channel, angle, or tee sections, fixed independently, without connecting plates etc conforming to Fe 410 W Gde E- 250, Quality B complete all as specified and as directed by Engineer-in-Charge.

Material and labour for machine cut, machine polished, green marble slab 18 to 20mm thick as in jambs and cills of windows etc , set, bedded and jointed with grey cement slurry & pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble slab laid over and including backing coat of 10mm thick in cement mortar (1:4) all as specified and as directed.

Material and labour for LLDPE Septic tank (10 users) with ISI marked, installed below the ground level and the same shall be placed over 150mm thick Plain cement concrete 1:4:8 (Nominal Mix) using 40mm graded coarse aggregate including necessary connection for inlet, outlet, vent pipe, rodding eye, backfilling as required as per manufacturer's instructions etc complete all as specified and as directed by Engineer-in-Charge. Make : Sintex Cat Part No: CCST-300-01 or equivalent Note : The unit quoted rate shall be deemed to include for following: (i) Excavation in soft/loose soil, RFR, removal of excavated soil and depositing the same outside the MD land. (ii) Size of excavation pit shall be approximately 600mm from external wall of the tank for work space. Depth of the pit should be decided based on position of inlet and outlet with required gradient and disposal point plus 150mm extra for bedding as directed by Engineer-in-Charge . (iii) Contractor is responsible for lowering the tank properly and positioning it in the pit vertically, centrally positioned, correctly aligned and leveled using a spirit level. The outlet pipe should face the soak pit and inlet pipe swivels, ensuring a straight connection and tank shall be checked for any leakage after installation and any damage during installation shall be borne by contractor.

M&L for Construction of soakage well of size 1.20 mtrs dia and 1.5 mtrs effective depth including excavation in any type of soil, foundation in PCC 1:3:6 type C2, wells of honey combed wall and solid slab in M-25 concrete ,, filter media , brick work, RCC cover slab M-25 filling withbrick bats complete all as specified and as shown in Drawing No CEPZ/2019/03 SHEET NO 1/2 and 2/2 dated 30 Apr 2019 and as directed.

Material and labour for Point wiring including necessary chases cutting in wall/flor/ceiling complete with PVC insulated FRLSH unsheathed cable 1100 volts grade with multi stranded copper conductor conforming to IS-694, 1.5sqmm (nominal area) ( Phase- R Y B, Neutral-Black), drawn through and including non metallic PVC conduit not less than 25mm dia (ISI marked) , ivory colour and accessories with sunken type modular GI box, not less than 1.2mm thick, for mounting of fittings like modular cover plates for mounting of switches, socket outlets,fan regulators etc. with modular metal inner plate and PVC cover plate and making good the disturbed surfaces as per the existing , including provision of PVC insulated FRLSH unsheathed copper cable 1100 volts grade with multi stranded copper conductor 1.5sqmm as earth continuity conductor and connecting to common earth dolly for One light point/ exhaust Fan point/Call bell point, controlled by one, one way switch complete all as specified and as directed by Engineer-in-Charge. Note- The rate of point wiring includes the following. :- Copper cables, PVC conduit with accessories , and other accessories such as modular GI box, modular inner plate and modular cover plate etc . Make of Cable-Plaza, Finolex, Havells, Polycab Make of PVC conduit-Anchor, Modi, Pressfit, Precision, Astral, Panasonic Anchor, Polycab, Presto Plast, Supreme

All as per item No.135 above but for one 3 pin socket outlet point, 5/6 Amps, on the same board with other switches, controlled by one switch.

All as per item No.135 above but for socket outlet point, 5/6 Amps, on independent board, controlled by one switch.

All as per item No.135 above but for one fan point controlled by one switch.

All as per item No.135 here-in before but for 3 pin 15 Amps socket point ,controlled by one switch on independent board with 2.5sqmm copper cable and provision of 2.5sqmm PVC insulated, FRLSH cable 1100 volts grade with multi stranded copper conductor for earth continuity conductor connected to common earth dolly connecting up to fittings complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Switch modular, flush type, single pole, one way, 5 Amps, 240 volts, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / Havells/.Crabtree/Leader

Supply and fix modular switch socket outlet, combination 2 in 1, 3 Pin, 5 Amps, flush type, universal ISI marked complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / Havells/.Crabtree/Leader

Supply and fix modular switch socket outlet, combination 5 in 1, 3 Pin, 5/16 Amps, flush type, universal ISI marked complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / Havells/.Crabtree/Leader

Supply and fix ceiling rose, 3 plate, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed by Engineer-in-Charge. Make: Legrand /crabtree/ Honeywell/ Anchor

Supply and fix modular stepped type electronic fan regulator,120W, 230 V etc complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / Havells/.Crabtree/Leader

Supply and fix LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose including 02 Nos of PVC square /round boxes , screws clips complete all as specified and as directed by Engineer-in-Charge. Make: Phillips Cat No BNO21C LED20S PSU CW GR S2 or equivalent of Havells cat part No LHEXARP7SN1W020 / Bajaj, as approved by GE.

Supply and fix angle holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / L&T

Supply and fix LED building security light fitting 35 Watt, luminaire fixture in IP 66 protection level output of LED lamp efficiency minium 100 luman per watt after all losses , pressure die-cast aluminium housing LED Street light complete with GI clamp including connected accessories and bracket made of GI Pipe 50mm dia light grade 1.25 m long, bend to shape with two sets of MS flat iron clamps, nuts, bolts, washers etc. complete all as directed by Engineer-in-Charge. Make Philips /Wipro / Havells

Supply & fix LED light fitting 10W bulkhead luminaires outdoor type including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size including all necessary fittings complete all as specified and directed by Engineer-in-Charge. Make: Havells/Crompton Greaves /Philips/ Bajaj

Supply and fix double door, sheet metal enclosure powder coated MCB DB SPN 4 way with 100 Amps rated bus bar, 240 volt, horizontal type, IP 43 protection, flush in walls including making good of disturbed surface to match with existing surface complete all as specified and as directed by Engineer-in-Charge. Make : Havells / Legrand / L&T / ABB / Siemens / Schneider

Supply and fix double door, sheet metal enclosure powder coated MCB DB SPN 8 way with 100 Amps rated bus bar, 240 volt, horizontal type, IP 43 protection, flush in walls including making good of disturbed surface to match with existing surface complete all as specified and as directed by Engineer-in-Charge. Make : Havells / Legrand / L&T / ABB / Siemens / Schneider

Supply and fix MCB SPN, 40 to 63 Amps, 240 volts,10 KA complete all as specified and as directed by Engineer-in-Charge. Make : Legrand / L&T / Havells / ABB / Siemens / Schneider

Supply and fix in repairs MCB SP, 6-32 Amps, 240 volts,10 KA complete all as specified and as directed by Engineer-in-Charge. Make : Legrand / L&T / Havells / ABB / Siemens / Schneider

Supply and fix in repairs MCB DP, 6-32 Amps, 240 volts,10 KA complete all as specified and as directed by Engineer-in-Charge. Make : Legrand / L&T / Havells / ABB / Siemens / Schneider

Supply and fix exhaust fan, AC, single phase, 230V, 250mm sweep, 1200 RPM, plastic body & blade with louver for protection of bird and rain water including cutting in wall, grouting the foundation bolt in the wall, making good the disturbed surfaces of wall including rendering, painting to match the existing surfaces and connecting up with three core flexible copper conductor cable of size 24/0.20sqmm etc from ceilling rose to fitting complete all as specified and as directed by Engr-in-Charge. Make- Crompton Greaves, Bajaj, Orient, Khaitan, Havells

Supply and fix ceiling fan complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep, minimum air delivery 210 CFM with service value 6.00 BEE, Five star rated with brushless direct current motor (BLDC) including suitable size of hanging clamp, nut and bolt etc complete all as specified and as directed by Engineer-in-Charge. Make : Usha/Bajaj /Orient/Havells/Crompton

Supply & Fix LED bulb of capacity 9 watt, retrofit type to fit in lamp holder complete all as specified and directed. Make: Havells/Bajaj/ CG/Shakti

Material and labour for Earthing complete with Galvanised steel earth plate electrode 60 cm x 60 cm x 6.0 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of earth the plate not less than 1.5 metres below normal ground level, connected to and including galvanised earth lead wire 4 mm dia, duly protected by 15mm dia light grade GI pipe upto test the point terminal block b means of bolts, nuts check nuts and washers of galvanised iron or steel as shown in electrial plate no.3 SSR-I connected to earth test point all as specified including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in pcc 1:3:6 type c-1 of size not less than 540mm x 540mm with RCC (1:2:4) type B precast cover (40cmx40cmx5cm) duly reinforced with including 8mm dia TMT bar @ 100mm c/c both ways one lifting handle made of 8mm dia TMT bar, embeded in precast cover slab flush to pit funnel 20mm dia GI medium grade watering pipe, charcoal and common slat in alternate layer and mixing of not less than 50 Kg Benzonite powder, 20 KG in each earthing packed upto maximum 30 cm on both side of plate for reducing the earth resistance complete all as specified and as directed by Engineer-in-Charge.

Supply and lay double wall corrugated (DWC) HDPE pipe 40mm outer dia and inner dia 32mm , as per IS-16205 including couplers and bend for cable protection laid in trenches and including all fittings as requied at site including cutting floor and making good the same to match the existing /adjoining surfaces etc complete all as specified and as directed by Engineer-in-Charge Make : TELEREX 450N/ Rex Polyextrusion Ltd/ Finolex/ Prince Pipes and fittings ltd/Kisan/Supreme/JAIN IRRIGATION SYS/ Astral

Supplying, laying,connecting, testing & commissioning LT UG XLPE insulated, heavy duty, 1100 V grade electric cable with aluminium conductor, served with an inner sheathing of PVC tape, armoured with galvanised steel wire or tape and overall PVC sheathed of size 16 Sqmm x 2 core, laid in trenches or passing through pipe or fixed to wall, making all connections with and including provision of necessary glands, lugs, bushing etc as required including taking down old unserviceable cable complete all as specified and as directed by Engineer-in-Charge of following sizes:- Note : Earthwork excavation, DWC pipe for cable protection shall be measured and paid separately in their respective items Make: Cable Corporation of India (CCI)/ Asian Cable Co, Chattisgarh/ Finolex/ Polycab/ Gloster/Universal/ RPG Cables Ltd , Thane/ Havells India Ltd/ RR Kabel/ KEI Industries Ltd(KEI)

Supply and fix galvanised iron pipe, light grade, 32mm bore for laying cable protection on wall, trenches, road crossings etc. with suitable size of GI saddle,clamps, nut & bolts wherever necessary complete all as specified and as directed by Engineer-in-Charge. Make: TATA/SWASTIK/JINDAL/Bharat Steel tube/ZENITH/Indian Tube Company

Supply and fix gun metal globe/ gate valve, 25mm bore, with iron wheel head, screwed both ends for iron pipes, ISI marked and fixed with suitable size of new union, nipple and reducer complete all as specified and as directed by Engineer-in-Charge. Make : Leader/Zoloto/Seiko/Sant/ Essco/Prayag

Material and labour for cutting the existing Bitumen Road /hard standing to size not exceeding 45cm wide and depth not less than 45cm for passing of UG cable through GI pipe and making good the disturbed surface filled with excavated material and top 200mm depth with plain cement concrete 1:3:6 type C2 using 40mm graded aggregate complete all as specified and as directed by Engineer-in-Charge

Material and labour for cutting the existing steel tubing for alterations or additions of pipe size 40/50mm bore and screwing complete all as specified and as directed by Engineer-in-Charge

mp construction co (BID ID -3448269)