Construction of Block 218 at NRB BARC Tarapur

Amount

Part -A Civil Dismantling of RCC works carefully manually without damaging adjacent structures excluding cutting of reinforcement including stacking of steel reinforcement bars and disposal of unserviceable materials within 200 m lead as per direction of Engineer-in-charge

Removing /dismantling chain link mesh from the existing chain linked fncing including removing GI hooks, nuts, bolts, washers, fixing rods etc.Making into rolls, transporting the dismantled materials to the scrap yard and stacking as directed by engineer in charge.

Demolishing Stone rubble masonry (In cement mortar) manually / by mechanical means carefully without damaging adjacent structures including stacking of serviceable materials and disposal of unserviceable materials within 100 m lead as per direction of Engineer-in-charge

Dismantling and stacking within 100 m lead fencing posts or struts including all earth work and dismantling of concrete etc "T" or "L" iron or pipe

From 0.00 to 1.50 m depth from average ground level

From 1.50 to 3.00 m depth from average ground level

From 3.00 to 4.50 m depth from average ground level

From 4.50 to 6.00 m depth from average ground level

From 1.50 to 3.00 m depth from average ground level

From 3.00 to 4.50 m depth from average ground level

From 4.50 to 6.00 m depth from average ground level

From 3.00 to 4.50 m depth from average ground level

From 4.50 to 6.00 m depth from average ground level

From 6.00 to 7.50 m depth from average ground level

Supplying and injecting with approved quality chemical emulsion at the rates and concentrations as per IS 6313-2001 Part II for preconstructional antitermite treatment and creating a chemical barrier under and around the masonry pits, masonry foundations, wall trenches, plinth filling, junctions of wall and floor, expansion joints, surfaces of RCC works for a depth of min. 500 mm from the finished ground level, surrounding of pipes, conduits etc., walls retaining soil above floor level, apron and drain along the perimeter of the building including all byeworks complete as per specification / IS 6313:2001 or latest revision and direction of Engineer In charge (only ground floor plinth area of the building will be measured for the payment in the following three stages. i)20% after completion of the foundations ii) 50% after completion of the ground floor flooring iii)30% after completion of all treatment works including ground floor doors & windows. Work to be executed by approved agency and specified guarantee for 10 (ten) years shall be furnished by the contractor.

Supplying, stacking and laying of 230 mm thick rubble soling stones as under floor base including packing with smaller stone and compacting, ramming including spreading and consolidation of blinding material, moorum etc. complete all as per specifications and as directed by the Engineer-in-charge

230mm With outside material

Supplying, Stacking and Laying of 150 mm thick rubble soling stones as under floor base including packing with smaller stone and compacting, ramming including spreading and consolidation of blinding material, moorum etc. complete all as per specifications and as directed by the Engineer-in-charge

Providing and laying in position PLUM Concrete with 70 % cement concrete of 1:3:6 (1 cement, 3 crushed sand, 6 graded stone aggregate of maximum size 20 mm) and 30 % 150 to 230 mm size soling stones spreading uniformly as per directions of the Engineer-in-Charge including consolidation, finishing, curing etc. complete as per specifications and drawings but excluding the cost of Form work shuttering, centering complete at all levels

Providing and laying in position cement concrete of 1:1.5:3 at all levels (1 cement, 1.5 crushed sand, 3 graded stone aggregate of nominal size 20 mm) including consolidation, finishing, curing etc.. complete as per specifications and drawings but excluding the cost of shuttering, centering and steel reinforcement.

Providing and laying in position Reinforced Cement Concrete (RCC) of grade M-30 using 20mm maximum size aggregates and crushed sand of approved quality including admixtures of approved brand and quality (plasticiser or super plasticiser) if required, including weigh batching, mechanical mixing, transporting, placing, pumping,vibrating, consolidation, finishing, curing etc. complete but excluding the cost of centering, shuttering and reinforcement complete as per specifications up to Plinth Level.

Providing and laying in position Reinforced Cement Concrete (RCC) of grade M-30 using 20mm maximum size aggregates and crushed sand of approved quality including admixtures of approved brand and quality (plasticiser or super plasticiser) if required, including weigh batching, mechanical mixing, transporting, placing, pumping,vibrating, consolidation, finishing, curing etc. complete but excluding the cost of centering, shuttering and reinforcement complete as per specifications above Plinth Level.

Providing , centering ,shuttering Form work using PVC film faced plywood to get a neat form finish surface for all types of structures including necessary strutting, proping, staging, supports etc and deshuttering the same after the specified time all as per drawings, specifications and as directed by the Engineer-in-charge at all levels

For Sub Structure

For Super Structure

Extra over above for staging / additional height in centering, shuttering in suspended floors, roofs, landing, high bays, beams and balconies or wherever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over height of 4.50m.(where exceeding 4.5 metre height in one floor shall be measured and paid for separately. Plan area to be measured for payment).

Staging / additional height in centering, shuttering upto 20 height

Providing & fixing in position ANCHOR SHELLS/EXPANSION SHELLS of standard & high quality of approved make suitable for various dia of bolts as mentioned below, with necessary bolts for structural steel work including drilling holes in RCC/masonry surfaces, aligning the bolts to the proper position& correct level all as per the specifications of the manufacturers including necessary scaffolding, bolts, washers & labour etc. complete as per the specifications and as directed by the Engineer-in-Charge

10mm Dia

12mm Dia

16mm Dia

Providing and fixing at all levels precast members using cement concrete of Grade M-30 in copings and / or bed blocks, plain window sills, shelves, louvers, steps, staircases, trench covers, drain covers etc. including hoisting and setting in position with C.M 1:3 (using crushed sand) cost of required centering, shuttering and finishing smooth with 6 mm thick cement plaster 1:3 (using crushed sand) on exposed surfaces complete as per specifications and as directed by the Engineer-in-charge

Providing & mixing pure acrylic based Polymer Modified Cementitious water proofing compound in concrete work (of approved brand & quality) mixed with cement in required proportions as per manufacturer's guidelines, specifications and as directed by the Engineer.

Treatment of construction joints by cutting of green concrete when in final set condition using approved air water jet at a suitable pressure in early age concrete including removal of laitance, draining the water from the air jet after the joint cutting process, treating the construction joint using surface retarding solvent free poly-hydroxyl chemical agent by removing the cement-sand matrix upto 5 to 7mm depth with an air water jet having pressure of 7 kg per Sqm., wire brushing, cleaning etc. complete all as per specifications and directed by the Engineer-in-charge.

Providing and fixing 20mm thick insulation cork surrounding of foundation area to provide insulation in vibration, thermal and accoustic applicaton complte all as pe specifications and direction of Engineer-In-Charge.

Providing and fixing in position 150 mm thick (adding and pasting 3 nos of 50 mm thick boards) Joint filler board of approved make in expansion joints to the required size and shape, placing and keeping in position complete as per specifications and drawings and as directed by the Engineer in charge.

Providing and filling in low-lying / backfill areas with approved self compacting controlled low strength material (Fillcrete with 1 cement : 28.58 crushed / manufactured sand : 0.429 fly ash : 0.0287 admixture mix) & flowable consistency comprising of cement, crushed / manufactured sand, fly ash & admixtures in the recommended proportions as specified below including mixing with water to achieve water cement ratio as approved, including loading, mechanical transportation, unloading, mixing, pumping, laying in layers, levelling all equipment, labour, supervision, scaffolding / staging for all leads, heights & levels etc. complete as per drawings, specifications and directions of the Engineer-in-Charge

Providing Reinforcement Steel for reinforced cement concrete at all levels including supplying, preparation of bar bending schedules, cutting, bending, transporting, fixing, tieing in position with PVC coated G.I binding wire, all labour charges, cost of cover blocks in specified grade of concrete etc. complete as per specifications and drawings.

Upto and including 32mm dia reinforcement: Using TMT bars of specified grades. TMT bars to be supplied as per specification in tender book using virgin materials

Providing Structural steel work using angles, channels, joists and other sections, welded and / or bolted in built up sections for trusses , structural steel floors, frame works, monorails and other structures including supplying, cutting, welding, fabricating, hoisting, fixing in position, applying a priming coat of approved steel primer etc. complete all as per specifications, drawings and as directed by the Engineer in charge

Up to and including 300 mm Joists, 350 mm channels, and below sections using materials as per specification in tender book.

Providing Structural steel work in M.S Plain Plates and chequered Plates for Embedded Parts, Trench Covers, Connection plates etc. Including cutting, hoisting, fixing in position and applying a priming coat of approved zinc chromate steel primer etc. Including cost of structural steel Plates, welding all labour charges etc. complete as per drawings and specifications. Using materials produced by vendors as per specification in tender book using virgin materials.

Providing and Fixing Anchor Fastener of approved make including drilling in concrete as per requirement for fixing Eps or other structures all as specified by the manufacturer complete all as per specifications and drawings

16 MM diameter 150 mm Long

20 mm diameter 100 mm Long

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing & staircases railing including applying a priming coat of zinc chromate steel primer etc. complete as per specifications using M.S tubes of ISI marked (Medium) of specified diameter and thickness

Providing and fixing at all levels MS bolts including nuts and washers of approved size, quality and make as per requirements and as per specifications, drawings complete all as directed at site by the Engineer in charge

Grouting below base plates of columns, equipments, around the foundation bolts, or locations as specified using pre-packed cementetious non-shrink grout (of approved brand & quality) including cleaning the base by water / compressed air, pre-soaking, shuttering / formwork, mixing, placing, curing etc. complete all as per manufacturer's guidelines and as directed by the Engineer-incharge.

Supplying and fixing Rolling shutters of approved make as per ISI standards made out of required size of MS lathes 18 gauge interlocked together throughout entire length and jointed together at the end by end locks mounted on specially designed pipes shaft with brackets, side guides and arrangements for inside & outside locking with push and pull operation complete including the cost of providing and fixing necessary springs of required size and M. S top cover of required thickness for rolling shutters

Rolling shutters (Laths Interlocked) gear operated type with handles including top hood 1.25mm thick

Extra over the cost of rolling shutters for providing and fixing motorized arrangements( with remote & manual operation) including designing, control panels, limit switches, required wiring and cables from panel to motor and required size of shaft etc of approved make all as per standard specifications including commissioning and testing complete as directed by the Engineer-in-charge.(only power supply point will be provided)

For rolling shutters up to 15.00 sq.m opening area.

For rolling shutters above 15.00 Sq.m and up to 30.00 sq.m opening area.

Extra over the cost of rolling shutters for providing wicket gate of specified size in the M.S rolling shutters including fixing with fixing arrangements, hinges, locking arrangements, frames etc. all as per standard specifications and as directed by the Engineer-in-charge complete.

Supplying, Assembling, fabricating, inspecting, testing, packaging, hoisting / erecting and fixing in position at indicated locations in RCC / Masonry/ Formwork, Stainless Steel Embedded Parts (EPs) (conforming to 304 L grade) of various sections such as plates, pipes etc. and in required sizes including mechanical transportation, aligning, fixing in position, providing necessary supporting arrangements etc. complete all as per drawings and specifications and as directed by the Engineer-in-Charge. The work includes preparation of fabrication drawings, documentation, safe delivery of materials to the project site etc. during civil construction. The work includes preparation of fabrication drawings, collection of Purchaser's Free Issue Materials, supply of requisite materials other than Purchaser's free issue materials (FIM), documentation, safe delivery to the project site, return of balance of FIM / scrap and erection during civil construction.

Providing and Laying Autoclaved Aerated cement block masonry of approved make with specified thick AAC Blocks in Super structure above plinth level up to 20 m height in cement mortar 1:4 (using crushed sand). The rate shall also include providing and placing in position 2 nos of 8 mm dia bars at every third course of the masonry work

Providing and fixing Glazed VITRIFIED floor tiles of approved make in different sizes conforming to IS 15622 in all colours and shades in Glossy or Matt or satin finish laid over a bed of minimum 20 mm thick bed of cement mortar 1:4 (using Crushed sand) and jointing with grey cement slurry including grouting with the joints with white cement based Tile Grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Engineer-in-charge

Using Tiles of size 600 X 600 mm

Using Tiles of size above 600x 600mm and up to and including 900 x 900mm

Providing and laying 50 mm thick cement concrete flooring with concrete hardener topping under layer 38 mm thick cement concrete 1:2:4 and top layer 12 mm thick wearing surface with metallic floor hardener, cement being mixed with metallic floor hardener of approved quality and make in the ratio of 4:1 (4 cement and 1 metallic floor hardener) by weight and this cement hardener compound mixed with 6 mm down graded stone aggregate in the ratio of 1:2 by volume including providing and fixing 25 X 3 mm aluminium strip, This includes cost of cement slurry, finishing to the required finishing and cleaning neatly while handing over the areas etc. complete as per specifications and drawings.

Providing and laying (IPS Flooring) cement concrete flooring 1:2:4, using crushed sand 50 mm thick finished smooth to the required level, finishing with a floating coat of neat cement including cement slurry, providing and fixing 25 X 3 mm aluminium strip, curing, cleaning the surface neatly at the time of handing over the area complete as per specifications and drawings as directed by the Engineer in charge

Providing and Laying Minimum 25 mm thick uniform shade Kotah stone treads and risers of steps, skirting, window sills in single length up to 2.00 metres length slab dado and pillars laid on 12 mm thick (average) cement mortar 1:3 (using crushed sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing to obtain mirror finish complete as per specifications, drawings and as directed by the Engineer-incharge

Extra for nosing in steps of treads Using Kotah stone

Providing and fixing 1st quality ceramic glazed floor tiles of minimum 300 - 600 mm long and 300 - 600 mm wide and thickness not less than 6 mm conforming to IS 15622 of approved make in all colours and shades as approved by Engineer-in-charge over a bed of 20 mm thick bed of cement mortar 1:4 (using crushed sand) and jointing with grey cement slurry including pointing with white cement based Tile grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Engineer-in-charge

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS 15622 of approved make. shade and colour of size ranging from 300 - 600 mm long and 300 mm - 600 mm wide and thickness not less than 6 mm as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (using crushed sand), setting the tiles in cement slurry and pointing the joints with matching colour Tile grout of approved make of matching shade including using PVC tile trim in the exposed corners, complete as per drawings, patterns and specifications complete as directed by the Engineer-in-charge.

Providing and fixing Minimum 17 mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut Granite of Jet Black colour for kitchen platforms, vanity counters, wash basin counters, door frames, window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (using crushed sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing the edges to give high gloss finish etc. complete at all levels

Providing wood work in frames of doors, windows, clear story openings and other frames, wrought framed and fixed in position of required size and shape including sawing, jointing, making rebates for shutters, making grooves as shown in the drawings, finishing the surfaces to the required finish all as per specifications and drawings including necessary MS hold fasts 40 mm X 3 mm thick, 200 mm long / with coach screws including protective painting to the surface that will come in contact with walls, joining materials, labour etc. complete all as per specifications and as directed by the Engineer-in-charge

Second class teak wood

Providing and fixing panelled teak wood door shutters (35 mm thick frames and 25 mm thick shutters) using second class teak wood using styles & middle rails 100 mm x 35 mm, bottom rail 200 mm x 35 mm, top rail & lock rails 150 X 35 mm and panelling with 25 mm thick best quality teak wood planks including fixing in existing door frame including ISI marked 100 mm stainless hinges with SS screws complete all as per specifications and as directed.

Providing and fixing FRP door shutters flush door / panelled type with plain colour or wooden veneer finish of approved make, design & colour. made out of 1.5 mm thick FRP skin moulded over wooden frame work of 40 mm wide and required thickness wooden styles and minimum 100 mm wide lock rails and wooden blocks for door stoppers, tower bolts, baby latch, aldrop, handles etc. wherever required and core filled with Polyurethane Foam and fixing with 4 Nos 100 mm (ISI marked) stainless steel hinges with S.S. wood screws

35 mm thick panelled door type of approved colours including the cost of 100 mm ISI marked heavy quality stainless steel butt hinges with necessary screws.

Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer of approved make with necessary accessories and screws etc. in wooden doors / steel doors with necessary bolts & nuts complete as per specifications and as directed by the Engineer-in-charge.

Providing and fixing stainless steel aldrops of size 300 X 14 mm of approved make with necessary screws, bolting from rear side complete as per specifications complete

Providing and fixing in position tapered / parallel threaded Tension Compression Mechanical Couplers for rebars conforming to IS code on “Reinforcement Couplers for Mechanical Splices of Bars for Concrete Reinforcement - Specification”. The couplers shall have bar break properties for 100% Tension and compression joints as per manufacturer's specifications and as per the direction of the Engineer. The item shall include all operations and arrangements such as threading with manufacturer's machines and operators, enlargement at connection by forging, provision of bar caps to protect the threads on rebar and related operations and arrangements as required for completing the work. The cost shall include testing of joints before usage of the splice as required by the Engineer at intervals

For 20mm dia. bars

For 25mm dia. Bars

For 32mm dia. Bars

Providing and fixing stainless steel tower bolts of size 250 X 12 mm of approved make with necessary screws etc.all as per specifications and as per drawings.

Providing and fixing pair of stainless steel "C" type door handles 10 mm dia, 250 mm long SS 304 grade solid rod , of specified size in steel doors/ wooden doors including screws / bolts etc. all as per drawings and specifications complete.

Providing and fixing brass mortise latch and lock of approved make with 6 levers and a pair of lever Brass handles with necessary screws etc complete suitable for fixing in wooden / steel/ FRP/ doors as per specifications.

Providing and fixing aluminium hanging heavy quality floor door stopper ISI marked with twin rubber stoppers, anodised transparent or dyed to required. colour or shade with necessary screws etc. complete.

Providing and fixing anodized aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / panelling, C.P brass / stainless screws all complete as per drawings and and directions of Engineer-in-charge including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required filling the gaps using silicon grout sealant etc. (fittings glazing and panelling shall be paid for separately)

Colour Anodised Aluminium sections (Minimum anodizing thickness of 15 micron)

Providing and fixing glazing in aluminium doors, window, ventilator shutters and partitions etc with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-charge (Cost of snap beading shall be paid in basic item)

With clear float glass panes of 6.00 mm thickness

Providing and fixing of Two Hour fire rated doors consisting of door frame and shutters and all hardware fittings as per IS 3614 part-1 & part-2 for stability and integrity. Pressed Galvanized steel confirming to IS 277 with the following specifications. The recommended fire doors shall have type test report from CBRI or ARAI or NABL approved lab for minimum rating of 2 hours with vision panel. Deviation in specification and sheet thickness other than what is entioned in the test certificates shall not be allowed. Proper label confirming the type of door and the hourly rating shall be mandatory. Door shall include fixing 4 nos heavy duty stainless steel 304 grade ball bearing, fire tested stainless steel butt hinges of size 100 x 75 x 3.00 mm (heavy weight) of approved make with suitable stainless steel screws, mortise / dead lock of approved make, a pair of 200 mm long stainless steel handles, 250 mm long stainless steel tower bolt / concealed tower bolt etc. frame hollow portion filled with PCC 1:2:4, necessary hold fast embedded in concrete, fixing in concrete with anchor fasteners. finished with Polyurethane painting of a pproved colour complete all as per drawings and specifications and as directed by the Engineer-in-charge

Providing and fixing fire rated Steel Rim Panic Exit Device of approved brand & quality in single leaf door upto 1000mm wide including all accessories etc. complete.

Providing 15 mm thick plastering using Ready mix internal plastering compound of approved make for internal faces of brickwork / concrete surfaces including preparation of the surface, curing, cleaning, scaffolding complete all as per specifications and as directed at site by the Engineer-in-charge

Providing 20 mm thick plastering using Ready mix external plastering compound of approved make for external faces of brickwork / concrete surfaces including preparation of the surface, curing, cleaning scaffolding up to 10 metres height complete.all as per specifications including forming drip moulds wherever necessary and as directed by the Engineer-in-charge

Providing and fixing G.I. chicken mesh in the junctions of concrete & brick work / masonry or as directed by the Engineer in charge including cutting, fixing with nails in position before plastering complete all as directed by the Engineer-in-charge. (only area of the chicken mesh used alone will be measured)

Providing and painting with two coats with oil bound distemper of approved make and manufacturer over new work to give an even approved shade and including priming coat with one coat of cement primer including preparation of surfaces, filling with putty if required, scaffolding complete as per specifications and as directed by the Engineer-in-charge.

Providing and applying white cement based wall putty of approved make over concrete or Plastered surface up to 3 mm thick to get uniform surface free from undulation including cleaning complete all as directed by the Engineer-in-charge

Providing and Painting with Epoxy PU paint using 2 coats of (120 Micron dry film thickness) Epoxy PU high build coating as finishing coat over a priming coat of EPILUX-13 High Build primer of 50 micron thickness over steel surfaces at all locations prepared and applied as per manufacturer' specifications including preparation of surface by cleaning with wire brush and rubbing, scraping , applying sand paper , making free of Rust, dust, dirt etc. filling the holes, joint, cracks if any using epoxy putty complete. all as per manufacturers technical data and as directed at site to achieve minimum overall dry Film thickness of 170 micron (50 Micron primer Coat + 120 micron finishing Coat). On STEEL surfaces

Providing, painting, finishing walls with two coats of anti-algae, weather proof acrylic smooth emulsion paint of approved make with silicon additives on sand face plaster/ plain plaster & concrete surfaces of required shade over new work over a base coat of exterior cement primer including preparation of the surfaces, scaffolding upto20m complete. as per specifications and as directed by the Engineer-in-charge.

Providing and applying Epoxy putty of approved make over concrete or Plastered surface up to 3 mm thick to get uniform surface free from undulation including cleaning complete all as directed by the Engineer-in-charge

Providing and painting two (or) more coats with Epoxy paint at all locations prepared and applied as per manufacturer' specifications including a priming coat if specified by the manufacturer, preparation of surface by cleaning with wire brush and rubbing with sand paper to remove dust, dirt etc, after first coat Epoxy based trowelling compound if required, including preparation of the surface by scrapping, applying sand paper, by cleaning with wire brush and rubbing, making free of rust, dirt etc. filling the holes, joints, cracks if any etc. complete.all as per manufacturers technical data and as directed at site to achieve 200 micron film thickness (50 micron primer coat + 150 micron finishing coat).

Providing and laying Self levelling Epoxy flooring , including preparation of the surface, primer coat, screeding & levelling coat and finishing coat with Polyurethane coat of approved colour and shade of approved make all as per manufacturers specifications complete as directed at site by the Engineer-in-charge (This Job to be carried out through a specialized approved agency)

2 mm thickness

Providing cement based water proofing treatment to the new terraces, chajjas, cleaning the concrete surfaces, giving injections to the top slab as required with cement and approved waterproofing compound solution to fill up all inherent holes, voids, honeycombs etc. in the concrete slab, setting brickbat coba in waterproof mortar with necessary gradient for easy flow of water and continue the treatment along the inner faces of parapet or other adjoining wall up to a height of 300 mm in thew shape of vattas, with waterproof plaster finished smooth with trowel in cement / geru with false markings of 300 mm squares complete as directed by the Engineer-incharge

With Average thickness of 120 mm and minimum thickness at khurra as 65 mm using river sand / crushed sand

Providing and laying water proofing treatment in sunken portions of WCs, bath rooms etc. by applying cement slurry mixed with water proofing cement compound consisting of applying: (a) 1st layer of slurry of cement @ 0.488 kg / sq.m mixed with water proofing cement compound @ 0.253 kg per sq.m. including injecting cement slurry .This layer will be allowed to air cure for 4 hours. (b) 2nd layer of slurry of cement @ 0.242 kg / sq.m mixed with water proofing cement compound @ 0.126 kg / sq.m. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with cement slurry. Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (using crushed sand) admixed with proprietary water proofing compound conforming to relevant IS and approved by Engineer-in-charge including mixing 'RECRON 3S' fibre at the rate of 125 grams per 50 kg of cement in top layer of plaster and finally finishing the surface with trowel with neat cement slurry in bottom and all the sides of sunken portion. complete as directed by the Engineer-in-charge. The treatment to be tested for water tightness before filling the sunken areas.

Providing and Fixing in position Suspended false ceiling system using 600 x 600mm Calcium Silicate Ceiling tiles having 15mm densified edges and 100% humidity resistance, incombustible as per BS476 part IV with thermal conductivity of 0.043 w/m KC and approved surface design and edge profile placed in a suspended grid of size of 600 x 600mm made of hot-dipped G.I steel sections having an exposed surface capping of pre-finished baked polyester painted coil wherein the main tee of size 24mm x 38mm x 0.33mm shall be suspended at 1200 mm centres along the length of ceiling with 4mm dia G.I wire with necessary level adjusters and cross tees of size 24 x 28 x 0.33mm x 1200 mm shall be inserted in to slots between the main tees at 600mm centres and thereafter in direction vertical to the longer tees, cross tees of size 24 x 28 x 0.33mm x 600mm shall be inserted to form a grid size of 600 x 600 mm resting on the periphery walls on wall angles of size 20mm x 20mm x 3000 mm x 0.40 mm thickness. The rate shall include providing necessary openings for light fixtures, diffusers, trap doors etc to be made as per layout drawings. The work shall be carried out as per directions of Engineer-incharge. The main tees to be suspended from the ceiling/ soffit with the help of metal dash fasteners of 6mmx50mm, soffit clits of 25mmx35mmx1.60mm and 4mm dia G.I wire with galvanised spring steel levelling clips. the entire grid system shall be designed to bear a distributed load of minimum 15 kg/Sq.m (Only calcium silicate false ceiling area will be measured for the purpose of payment)

False Ceiling- tiles

Providing and fixing Lay in False Ceiling 600 x 600mm unperforated corrosion resistant aluminium magnesium alloy metal panel fixed in 24 mm 'T' Frame work of Module 600 x 600 mm. Panels shall be manufactured by of size 575 mm x 575 mm of approved colour in 0.70 mm thick Aluminium Alloy 3105 with square edges Tiles to be stove enamelled on a continuous application for pre-treatment. The coils to be go through 4 stages of pre treatment Three times of oven baked through conversion coating , priming and finish coat ensuring superior adhesion, high corrosion resistance and good colour stability. The coils to be painted on both sides after degreasing. Inside surface to have a primer of 5 microns and a coat of natural colour of 5 microns, exposed surface to have a primer of 5 microns, binder of 5 microns and a topcoat of approved colour 15 microns. Grid system for fixing ceiling tiles shall comprise of tees. The 24 mm main tee runners shall be suspended at an interval of 1200 mm centre to centre. The 24 mm cross tee runner shall be suspended at an interval of 600 mm centre to centre and further supported with 24 mm cross tee with inter locking arrangements to form a Grid of 600 mm x 600 mm. The main tee shall be supported by means of 4 mm G.I.rod from slab / roof. The suspension shall be provided at 1200 to 1500 mm centre to centre. Provision for lights, diffusers etc to be made including extra supports wherever necessary. Measurements shall be as per actual area of false ceiling with out deductions for lights and diffusers.

Providing and fixing hand rail using 304 grade Stainless Steel pipes of approved size and make and quality by welding, mirror / matt polishing, fixing at site etc. for balcony railing & staircases railing including special sections as per drawings, specifications. complete as directed by the Engineer-in-charge

Providing and fixing white vitreous china European type Water Closet with 'P' or 'S' Trap with solid seat and lid of approved make, 10 litre low level white PVC flushing cistern with manually controlled device (handle lever) conforming to IS:7231, flush bend, fixing EWC with C.P brass screws, 15 mm PVC heavy quality inlet connection of 450 mm long, including testing , commissioning & cleaning etc. complete all as per drawings and specifications and as directed by the Engineer-in-charge

E.W.C. pan in White colour with ISI marked white solid plastic seat and lid.

Providing and fixing white vitreous china flat back half stall urinal size 580 x 380 x350 mm / 610 mm Aquaseal model of approved make with approved make 32mm C.P flush value with standard flush pipe and C.P. brass spreaders, 32mm urinal waste coupling with dome grating and clamp etc. including making G.I water line connection complete as directed by the Engineer-incharge (Only G.I. pipes will be paid under relevant Item )

Single half stall urinal with C.P brass Flush valve. Note : For fixing flush valve 32 mm G.I water line provision to be made which will be paid under relevant Item .

Providing and fixing vitreous China wash basin of approved make and colour with C.I. brackets, 15 m C.P. brass pillar tap of approved make,15 mm x 600mm long PVC Inlet connection, 32 mm heavy quality C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls and testing complete all as per specifications and as directed by the Engineer-in-charge

White vitreous China counter top / counter below wash basin size 560 x 410 mm / 560 x 450 mm with single 15 mm C.P. brass pillar tap (OVAL / ROUND Models)

Providing and fixing stainless steel toilet paper holder recessed type of approved make and type with S.S screws as directed by the Engineer-in-charge complete.

Providing and fixing heavy quality CP brass bottle trap 31 / 32 mm of approved make single piece moulded with height of 270mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, of approved make for wash basins / urinal etc all as per specifications and directed by the Engineer in charge.

Providing and fixing heavy quality health faucet with 1.50 metres long flexible hose (hand shower) of approved make with wall brackets and type as per specifications and as directed by the Engineer-in-charge

Providing and fixing C.P brass Angle cock of heavy quality of specified / approved make, for wash basin inlet / flush cistern etc. as per specifications and as directed by the Engineer-in-charge

Providing and Fixing 15 mm CP brass Angle stop cock of approved make- quarter Turn

Providing and fixing C.P brass 2 way Angle cock (2 Angle cock combination in single fitting) of heavy quality of approved make as per specifications and as directed by the Engineer-in-charge.

Providing and fixing 15 mm C.P brass tube 600 mm long with nuts and washers complete for wash basins / urinals with all necessary accessories complete as directed by the Engineer-incharge

Providing and fixing cast iron nahani trap / floor trap of 100 mm inlet and 75 mm outlet, (weighing 5.80 Kg each), jointing with lead with the connection pipes, placing as per the drawings, embedding in cement concrete 1:2: 4 and making circular hole up to floor level using 110 mm O/D PVC pipes of 6 Kg / sq.cm pressure and fixing 1 No 125 mm dia C. P brass grating , complete all as specifications and drawings and as directed by the Engineer-in-charge

Providing, laying , jointing, fixing and testing heavy quality ( (ISI Marked C-Class) Galvanised Iron pipes and ISI marked fittings like, tees, elbows, bends, unions, nipples, reducers etc. as required for the work, including testing the pipes and fittings for 10.00 Kg / Sq.Cm hydraulic pressure with a minimum period of two hours duration with clean water, including cutting , threading, jointing with hemp yarn, white lead, jointing teflon tape, chasing walls and making good by filling with concrete 1:3:6, complete all as per specifications and drawings, including two coats of anti corrosive bitumastic paint, all as directed by the Engineer-in-charge. Pipes with ISI marked 'C' - Class heavy quality pipes of approved make.

15 mm dia G.I pipe

20 mm dia G.I pipe

25 mm dia G.I pipe

32 mm dia G.I pipe

Providing & fixing in position heavy pattern screw down gun metal gate valve with handles and wheels of approved make including testing for 10Kg/cm2 pressure with clean and potable water with a minimum testing duration of two hours etc.as per specification and as directed by the Engineer-in-charge

Providing, hoisting and installing at required elevation moulded HDPE cylindrical vertical water storage tanks of approved make of the following capacities with suitable S. M. C cover at top including the cost of labour for making hole in the storage tank for inlet, outlet, scour and overflow, providing and fixing necessary G.I Nipples ranging from 15 mm to 50 nn n.b of average150 mm length with double check nuts, washers etc. complete as directed by the Engineer-in-charge

HDPE CYLINDRICAL vertical storage water tank 1000 lit capacity

Providing and laying non pressure NP2 class RCC Hume pipes of approved make, with collars jointed with stiff mixture of cement mortar in the proportion of 1:2, laying to the levels, slopes and as per the drawings and specifications and as directed by the Engineer-in-charge including testing of joints etc. complete.

250 mm Dia RCC Hume pipe class Np2

150 mm Dia RCC Hume pipe class Np2

Providing and constructioning Inspection chambers of Internal size clear dimension of 900 x 600 mm in 230 thick brick masonry with cement mortar 1:4 over a bed of 150 mm thick 1:4:8 cement concrete foundation, plastering with cement mortar 1:4 20 mm thick on inside, out side and all exposed surfaces finished with a floating coat of neat cement, brick corbelling at top to provide opening of 900 X 450 mm, embedding the frame and cover with CC 1:2:4 concrete, and fixing cast iron steps if necessary at 300mm intervals complete . Depth of chamber not exceeding 900 mm. (excavation, soling, cast iron cover and C.I steps will be paid separately under relevant item)

Extra depth over initial depth of 900 mm for chambers of 900 x 600 mm internal size. Including fixing cast iron steps (C.I steps shall be paid under relevant item)

Supplying and fixing Cast Iron Man hole or Cast Iron Steps cover of approved make and weight as specified in the drawings or as directed by the Engineer in charge.

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix cement plastered on both sides with cement mortar 1:3 finished with a floating coat of neat cement and making necessary channels for the drain etc. complete.

For pipes 100 to 230 mm diameter

Providing, supplying, fixing in position, under floors or in walls sand cast iron pipes including required specials like bends, tees, 'Y' collars, cowl etc for soil, waste and ventilation pipes conforming to IS.1729 of approved make including cost of jointing with spun yarn and molten lead of specified quantity, caulking the joints, including testing of pipes, painting with primer, fixing at walls with necessary approved type of clamps and brackets complete all as per drawings and specifications and as directed at site.

75 mm dia sand cast iron S&S pipe as per IS:1729 with 0.90 kg lead / joint

100 mm dia sand cast iron S&S pipe as per IS:1729 with 1.00 kg lead / joint

Providing and fixing square mouth S.W. gully trap complete with CI grating brick masonry chamber with water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.5 kg and frame to be not less than 2.70 kg as per standard design

150 x 100 mm size gully trap "P" type

Providing, supplying, fixing in position in walls Rain water down take pipes using Centrifugally cast iron pipes (3.00 metres long) including required specials like bends, shoes etc for Rain water down take pipes Confirming to IS.3989 of approved make including cost of Jointing with spun yarn and molten lead of specified quantity, caulking the joints, including testing of pipes, painting with primer , fixing at walls with necessary approved type of clamps and brackets complete all as per drawings and specifications and as directed at site.

150 mm C.I . rainwater down take pipe with 1.20 Kg lead per joint (pipe as per IS 3989)

Providing and fixing cast iron grating for rain water down takes at roof including chipping and grouting complete all as directed by the Engineer-in-charge

200 mm x 200mm

Providing and fixing G.I pipe sleeves 600 mm long of specified size with puddle flange of specified size for rain water down takes to be embedded in RCC slabs/ RCC roof gutters to connect rain water pipes by welding or with screwed sockets all as per the drawings and as directed at site. (These sleeves to be fabricated and embedded at the time of concreting in true vertical )

Heavy quality 'C' class 100 mm n/b G.I pipe of approved Make with 200mm x 200mm puddle flange

Providing and constructing storm water chambers of internal clear dimension of 600 x 600 x 1200 mm deep in 230 thick brick masonry with cement mortar 1:4 over a bed of 150 mm thick 1:4:8 cement concrete foundation, plastering with cement mortar 1:4 20 mm thick on inside, outside and all exposed surfaces finished with a floating coat of neat cement, embedding the C.I frame and cover / RCC with 1:2:4 concrete / RCC Precast slab by making suitable rebate in concrete, and fixing cast Iron steps if necessary at 300 mm intervals complete as directed by the Engineerin- charge. Depth of Chamber not exceeding 1200 mm. (Excavation, soling, cast iron cover, C.I steps and precast slab will be paid separately under relevant item)

Providing and constructing brick work in cement mortar using Standard bricks of approved quality / class, make / brand in super structure above plinth and upto floor II in all shapes and sizes including curing, raking out joints complete as per specifications and as directed by the Engineer-in-charge

Brickwork in super structure with standard bricks in C.M 1:4 using crushed Sand

Providing and fixing GI chain link fabric fencing Made of GI wire of dia 4 mm of required width in mesh size 50 x 50 mm including strengthening with 2mm dia wire or nuts, bolts and washers as requeid complete as per direction of Engineer-in-charge.

Fencing with RCC post placed at required distance, embedded in cement concrete blocks every 15th post, last but one end post and corner post shall be strutted on both sides and end post one side only, provided with horizontal lines and two diagonals of barbed wire 9.38 kg per 100 metres (min) between the two posts fitted and fixed with G.I. staples on wooden plugs or G.I. binding wire tied to 6 mm bar nibs fixed while casting the post etc. complete as directed by the Engineer-in-charge. (cost of RCC posts, struts, earth work and concrete to be paid for separately) : Payment to be made per metre cost of total length of barbed wire used

With G.I. barbed wire 12 swg

Providing, supplying and fixing hollow metal flush steel doors 40 mm thick of approved make consisting of door frame and shutters and all hardware fittings, frame made out of 14g thick G.I sheets and shutters made of 16g thick sheets, hollow portion filled with puff, including necessary stiffeners in shutters and frame, vision panel of specified size with 4 mm glass and clip on pressed steel frame for vision panels, fixing 4 nos heavy duty stainless steel 304 grade ball bearing, fire tested stainless steel butt hinges of size 100 x 75 x 3.00 mm (heavy weight) of approved make with suitable stainless steel screws, mortise / dead lock of approved make, a pair of 200 mm long stainless steel handles, 250 mm long stainless steel tower bolt, etc. frame hollow portion filled with PCC 1:2:4, necessary hold fast embedded in concrete, fixing in concrete with anchor fasteners. finished with Polyurethane painting of approved colour complete all as per drawings and specifications and as directed by the Engineer-in-charge

Part-B Electrical ELECTRICAL PANELS Power & Motor Control Centres (N-PMCC & E-PMCC & LPBS)

Supply & testing at manufacturer's works, installation & commissioning of 415V, single front, fixed type Normal Power & Motor Control Centre comprising of Electrolytic grade Copper busbar (TPN) of 400A rating, suitable for top cable entry & exit, IP 54, suitable for withstanding a symmetrical short circuit fault current of 50 kA (rms) for 1 sec. and other necessary accessories as per detailed technical specifications & SLD. The panel shall comprise of following incoming & outgoing feeders: Incoming feeder: 1 No. 4P, 400A, Icu=Ics=50kA, MCCB with Extended Rotary handle and Thermal based releases for overload, short circuit and earth fault protections along with shunt release. Outgoing feeders: i) 2 Nos. 110KW VFD Motor Starter (open transition type) along with Short circuit Protection Device (SFU 200A) complying Type-2 coordination. ii) 6 Nos. 63A, 3P-N, Icu=Ics=50kA, MCCB and SFU with Extended Rotary handle and adjustable type thermal and fixed magnetic releases for overload and short circuit protections. iii) 1 No. 63A, 3P-N, Icu=Ics=50kA, MCCB with adjustable thermal and fixed magnetic releases for overload and short circuit protections respectively. Outgoing Distribution Board shall consist of 04 nos. 32A, TPN, MCCB, Icu=Ics=25kA, MCCB with adjustable thermal and fixed magnetic releases for overload and short circuit protections respectively.

Supply & testing at manufacturer's works, installation & commissioning of 415V, single front, fixed type Emergency Power & Motor Control Centre comprising of Electrolytic grade Copper busbar (TPN) of 400A rating, suitable for top cable entry & exit, IP 54, suitable for withstanding a symmetrical short circuit fault current of 50 kA (rms) for 1 sec. and other necessary accessories as per detailed technical specifications & SLD. The panel shall comprise of following incoming & outgoing feeders: Incoming feeder: 1 No. 4P, 400A, Icu=Ics=50kA, MCCB with Extended Rotary handle and Thermal based releases for overload, short circuit and earth fault protections along with shunt release. Outgoing feeders: i) 2 Nos. 110KW VFD Motor Starter (open transition type) along with Short circuit Protection Device (SFU 200A) complying Type-2 coordination. ii) 6 Nos. 63A, 3P-N, Icu=Ics=50kA, MCCB and SFU with Extended Rotary handle and adjustable type thermal and fixed magnetic releases for overload and short circuit protections. iii) 1 No. 63A, 3P-N, Icu=Ics=50kA, MCCB with adjustable thermal and fixed magnetic releases for overload and short circuit protections respectively. Outgoing Distribution Board shall consist of 04 nos. 32A, TPN, MCCB, Icu=Ics=25kA, MCCB with adjustable thermal and fixed magnetic releases for overload and short circuit protections respectively.

Supply & testing at manufacturer's works, installation & commissioning of 415V, single front, fixed type Distribution Board of Electrolytic grade Aluminium busbar (TPN) of 80A rating, suitable for top cable entry & exit, IP 54, suitable for withstanding a symmetrical short circuit fault current of 50 kA (rms) for 1 sec. and other necessary accessories as per detailed technical specifications & SLD. The panel shall comprise of following incoming & outgoing feeders: i) 01 Nos. 80A, 2P, Icu=Ics=25kA, MCCB and Extended Rotary handle and adjustable type thermal and fixed magnetic releases for overload and short circuit protections. ii) 2 Nos. 63A, 40A & 32A Each, 2P, Icu=Ics=25kA, MCCB with adjustable thermal and fixed magnetic releases for overload and short circuit protections respectively.

EARTHING & LIGHTNING PROTECTION SYSTEM Earth Pits

Earthing with tinned copper earth plate 600mm x 600mm x 3.15mm thick including accessories, GI clamp, test link,connection of 2 x 95sqmm copper conductor, providing concrete inspection pit with cast iron cover having lifting lug and locking arrangement, 50mm dia GI watering pipe with funnel, charcoal/coke, salt, excavation, backfiling with black cotton soil, compacting watering, etc as required.

Earthing with tinned copper earth rod 25mm dia x 3mtr long including accessories,GI clamp, test link, connection of 2 x 95sqmm copper conductor, providing concrete inspection pit with cast iron cover having lifting lug and locking arrangement, 50mm dia GI watering pipe with funnel, charcoal/coke, salt, excavation/piling, backfiling with black cotton soil, compacting watering, etc as required.

Earthing Conductor Supply and laying of following size earthing conductor at 1000mm below ground level including excavation, connection to earth pits, refilling the trench, etc as required. 2x95 sqmm stranded bare tinned copper conductor

Supply and embedment of following size earthing conductor at 100mm below finish floor level including brazing with earth continuity conductor, claming etc as required. 2x95 sqmm stranded bare tinned copper conductor

Supply and laying of following size earthing conductor on surface/surfaced including clamping/cleating on structure/floor/ceiling/wall/tray, making chase, repairing the same,interconnection through brazing/bolting, etc as required.

2x95 sqmm stranded bare tinned copper conductor

70 sqmm stranded bare tinned copper conductor

10 sqmm stranded bare tinned copper conductor

14 SWG solid bare tinned copper conductor

25mm x 3mm tinned copper flat

Supply and fixing of 25mm x 6mm GI strip along tray using suitable size GI saddle/clamp including interconnection, hardwares, etc as required

Earth Plates Supply and embedment of copper earth plate/pad of size 40mm wide x 6mm thick x 500mm long having 09 nos. of 10 mm dia tapped holes for outgoing connections and 11mm dia rod on back side for brazing of 2 nos. of 95 sqmm copper conductor including brazing, connection with suitable hardwares etc as required.

Earth Tails Providing and fixing earth tails of 300mm length of following size including connection and brazing with earth continuity conductor.

95 sqmm stranded bare tinned copper conductor

70 sqmm stranded bare tinned copper conductor

Earth Connection Providing earthing conductor end terminations using suitable size heavy duty tinned copper lugs for connection to earth plate/pad, motor and other equipment, etc

95 sqmm stranded bare tinned copper conductor

70 sqmm stranded bare tinned copper conductor

10 sqmm stranded bare tinned copper conductor

14 SWG solid bare tinned copper conductor

Providing and fixing 300mm length cable tray equipotential bonding conductor made up of 10sqmm flexible stranded bare copper conductor having copper lugs at both ends for connection.

Vertical Air Termination Supply and fixing vertical air termination made up of 20mm dia, 1 mtr long copper rod attached to 50mm dia. Copper sphere having drilled and tapped holes for fixing 5 nos. of 150mm long spikes.

Test Link Box Supply and installation of test link box for interconnection of down conductor from lightning protection system to lightning earth pit and should consist of 2 mm thick CRCA weather proof sheet enclosure with cover, having 25mm x 3mm copper strip link, teflon sealing after connection, earthing stud, etc as required.

LIGHTING SYSTEM Distribution Boards Supply, installation, testing and commissioning of following configuration 415V, 3-phase, 4 wire, pre-wired with copper HFFR wires, IP-54, MCB Distribution Board fabricated out of 2mm thick Hot dip galvanised G.I. sheet steel, duly powder coated with RAL 7032 shade, suitable for surface/recess mounting complete with fork (or comb type) busbar, earth bar with connection screws or nut bolts, DIN rails for MCB mounting, terminal blocks (screw connection type), 2 mm thick removable gland plate on both top and bottom sides with required number of knock out holes, neoprene gasket etc. as required as per SLD and technical specifications.

6 way having 1 no. main incomer of 16A TPN MCB with 3 nos. 16A, DP, RCBO (10kA,100mA) as incomer for each phase and 18 nos. outgoing of 6A, 10kA SPN MCB (Isc=10kA)

4 way having 1 no. main incomer of 16A TPN MCB with 3 nos. 16A, DP, RCBO (10kA,100mA) as incomer for each phase and 12 nos. outgoing of 6A, 10kA SPN MCB (Isc=10kA)

4 way having 1 no. main incomer of 25A TPN MCB with 3 nos. 25A, DP, RCBO (10kA,100mA) as incomer for each phase and 12 nos. outgoing of 16A, 10kA SPN MCB (Isc=10kA)

Supply, installation, testing and commissioning of following configuration 240V, 1-phase, 2 wire, pre-wired with copper HFFR wires, IP-54, MCB Distribution Board fabricated out of 2mm thick, hot dip galvanised G.I. sheet steel, duly powder coated with RAL7032 shade, suitable for surface/recess mounting complete with appropriate rating fork (or comb type) busbar, earth bar, DIN bar for MCB mounting, 2 mm thick removable gland plate on both top and bottom sides with required number of knock out holes, neoprene gasket etc., as required, as per SLD and technical specifications.

6 way having 1 no. main incomer of 25A DP MCB and 6 nos. outgoing of 16A, 10 kA DP MCB (Isc=10kA)

Lighting Fixtures

Supply, testing & installation of 1x150 W, 240V, 50Hz, Highbay LED with luminaire efficacy>150 lm/W, system output ≥ 22500 lm, THD < 10%, PF ≥ 0.9, CRI >70, CCT > 5700K, IP 65, IK06 impact rating. Driver shall have 4KV surge protection. Luminaire should have service life of 50,000 hrs. Pendant mount kit with necessary brackets, anchor fasteners, plates etc. is included for installation in ceiling.

Supply, testing & installation of 1x80 W, 240V, 50Hz, Highbay LED, luminaire efficacy>150 lm/W, system output ≥12000 lm, THD<10%, PF≥0.9, CRI>80, CCT > 5700K, IP 65, IK08 impact rating. Driver shall have 4KV surge protection. Luminaire should have service life of 50,000 hrs. Surface mount kit with necessary brackets, anchor fasteners, plates etc. is included for installation in ceiling.

Supply, testing and installation of 4ft Functional Batten with 2x18W LED Tube with a nominal system lumen output of 4200 lumens and a minimum system efficacynot less than 100lm/W. The luminaire should have a colour temperature of 6500K and CRI>80. The luminaire shall meet IP20 rating with THD < 10% and PF > 0.95. The luminaire housing should be made of white powder coated CRCA sheet steel. The total power consumption should not exceed 38W (including driver).

Supply, testing and installation of LED wellglass luminaire with a nominal system lumen output of 3700 lumens and a minimum system efficacy of not less than 110 lumen/watt. The luminaire should have cool white colour temperature and a CRI>70. The luminaire shall meet IP65, IK 08 rating with THD<10% & Pf>0.9. The luminaire housing should be made of pressure die cast aluminium. The total power consumption should not exceed 34W (including driver).

Supply, testing and installation of LED integral driver flood light with a nominal system lumen output of 7000 lumens and a minimum system efficacyof 100 lumen/watt. The luminaire should have cool white colour temperature and a CRI>70. The luminaire shall meet IP66 rating with THD<20% & Pf>0.9. The luminaire housing should be made of pressure die cast aluminium. The total power consumption should not exceed 72W (including driver).

Supply, testing and installation of LED Bulkhead with a nominal system lumen output of 700 lumens and a minimum system efficacy of 105 lm/W. The luminaire should have a color temperature of 6500K and CRI > 70. The luminaire shall meet IP65 rating and IK 08 rating with THD < 20% and PF > 0.9. The luminaire housing should be made of High pressure die cast Aluminium with high quality PMMA diffuser. The total power consumption should not exceed 6.5W (including driver).

Sockets & Switches

6A, 2P+E, 1PH, MCB controlled Industrial socket with plug.

16A, 2P+E, 1PH, MCB controlled Industrial socket with plug.

6A, 5 pin, 1PH, modular type decorative switch socket unit with pre-fabricated GI switch box with front plate.

16A, 5 pin, 1PH, modular type decorative switch socket unit with pre-fabricated GI switch box with front plate.

6A, 2P+E, 1PH, Industrial socket without MCB for filter bank area.

6A, 2P+E, 1PH Modular type decorative sockets with pre-fabricated GI switch box with front plate (for Beam Detector & PPS).

6A, single pole industrial tumbler type switch with pre-fabricated GI switch box with outer GI cover or front plate.

Conduits Supply and embedment of 16 SWG black enamaled heavy duty rigid mild steel (MS) ERW conduit pipe of following sizes along with all accessories such as bends, junction box, socket, check nut etc. including making threads, removing burrs, connection of accessories, drawing of fish wire, laying in RCC slab, beam and wall, cutting & laying in brick wall etc. as required under the instruction of Engineer-in-charge surface type junction boxes of min. 75mm deep shall be provided in slab.

Wiring Wiring for primary light point/exhaust fan point and secondary light points (For length above 10 m) with 1.5 sqmm HFFR PVC insulated copper conductor single core flexible wire in recessed conduit with round block, ceiling rose, etc as required but without switch, switchbox and switchbox cover.

Wiring for secondary light points/exhaust fan points with 1.5 sqmm HFFR PVC insulated copper conductor single core flexible wire in recessed conduit with round block, ceiling rose, etc as required but without switch, switchbox and switchbox cover.

Type-A (up to 5 m length)

Type-B (up to 7 m length)

Type-C (up to 10 m length)

Wiring for power point with 2 x 2.5 sqmm HFFR PVC insulated copper conductor single core flexible wire in existing laid surface/recessed conduit but without power socket and switch unit, switchbox and switchbox cover.

Supply and laying 14SWG bare copper wire along conduit with clamping etc. for open wiring.

Junction Boxes/ Cable Pull Boxes (For Building Periphery Lights) Junction box/Cable pull box shall be weather proof type, fabricated out of 2 mm thick CRCA sheet, cable gland plate at the bottom, suitable to terminate 2 nos. of 3 core x 1.5 sqmm cable, 8 nos of terminals, etc as required.

CABLING SYSTEM CABLES Supply and laying of 1.1kV grade aluminium conductor (H2/ Class 2 stranded shaped), extruded XLPE insulated, extruded PVC (ST-2) inner sheathed and extruded FRLS PVC (ST-2) outer sheathed, GI round wire armoured power cable (on steel drums) of following sizes on overhead cable tray or cleating on wall/ceiling,including tying, clamping, putting cable tag, marking, etc as required:

3.5 core x 300 sq.mm

3 core x 120 sq.mm

Supply and laying of 1.1KV grade copper conductor (annealed/ Class 2 stranded shaped), extruded XLPE insulated, extruded PVC inner sheathed and extruded FRLS PVC outer sheathed, GI round wire armoured power cable (on steel drums) of following sizes on overhead cable tray or cleating on wall/ceiling,including tying, clamping, putting cable tag, marking, etc as required:

2 core x 6 sq.mm

2 core x 16 sq.mm

2 core x 35 sq.mm

4 core x 4 sq.mm

4 core x 10 sq.mm

Supply and laying of 1.1 kV grade copper conductor, extruded PVC (Type-A) insulated, extruded PVC (ST-1) inner sheathed and extruded FRLS PVC (ST-1) outer sheathed, GI round wire armoured control cable (on steel drums) of following sizes on overhead cable tray or cleating on wall/ceiling,including tying, clamping, putting cable tag, marking, etc as required:

10 core x 1.5 sq.mm

Supply and making cable end termination with brass double compression gland with PVC shroud and crimping type aluminum lugs for following size of XLPE insulated FRLS PVC sheathed aluminum conductor power cable of 1.1KV grade.

3.5 core x 300 sq.mm

3 core x 120 sq.mm

Supply and making cable end termination with brass double compression gland with PVC shroud and crimping type copper lugs for following size of XLPE insulated FRLS PVC sheathed copper conductor power cable of 1.1KV grade.

2 core x 6 sq.mm

2 core x 16 sq.mm

2 core x 35 sq.mm

4 core x 4 sq.mm

4 core x 10 sq.mm

Supply and making cable end termination with brass double compression gland with PVC shroud and crimping type copper lugs for following size of PVC insulated FRLS PVC sheathed copper conductor control cable of 1.1kV grade.

10 core x 1.5 sq mm

Cable Trays & Accessories Supply and installation of ladder type cable tray of following size fabricated out of 2 mm thick sheet steel having side channel of 100 mm, rungs spaced at 250 mm, hot dip galvanized, single length not less than 2.5 m with two coupling/joint plates per tray length having one long groove for adjustment and suitable for indoor environment

300 mm wide

Supply and installation of ladder type cable tray of following size fabricated out of 2 mm thick sheet steel having side channel of 50 mm, rungs spaced at 250 mm, hot dip galvanized, single length not less than 2.5 m with two coupling/joint plates per tray length having one long groove for adjustment and suitable for indoor environment.

150 mm wide

Supply and installation of perforated type cable tray of following size fabricated out of 2 mm sheet steel having side channel of 50 mm, cross perforation not more than 17.5%, hot dip galvanized, single length not less than 2.5 m with two coupling/joint plates per tray length having one long groove for adjustment and suitable for indoor environment.

150 mm wide

Fire Barrier & Fire Breaks

Water based fire stop/fire barrier with min 3 hr fire rating for cable opening and suitable for retrofitting along with fire sealant,making frames, finishing, etc as required

Fire retardent cable coating paint with min 30 min fire rating for horizontal and vertical cable runs

EMBEDDED PLATES/ STRUCTURAL STEEL Supply and erection of MS enclosure box (for DBs) of following sizes made of 2 mm thick sheet steel with required cutting, welding, bending, stiffners, removable plate on four sides, 2 nos. earthing studs on outer and inner sides, two coats of red oxide paint etc. and embed in concrete or brick wall, cutting brick wall to suit size, etc. as required under the instruction of engineer-in-charge.

797 mm (L) x 115 mm (B) x 765 mm (H) (for 6-way, 3-Ph, DB)

722 mm (L) x 115 mm (B) x 765 mm (H) (for 4-way, 3-Ph, DB)

450 mm (L) x 115 mm (B) x 290 mm (H) (for 6-way, 1-Ph, DB)

Supply and erection of MS enclosure box (for switches & plug sockets) of following sizes made of 2 mm thick sheet steel with required cutting, welding, bending, stiffners, removable plate on four sides, 2 nos. earthing studs on outer and inner sides, two coats of red oxide paint etc. and embed in concrete or brick wall, cutting brick wall to suit size, as required under instruction from engineer-in-charge.

270 mm (L) x 220 mm (W) x 70 mm (D) (for industrial plug sockets with MCB)

250 mm (L) x 150 mm (W) x 70 mm (D) (for industrial switches)

Supply and embedment of MS Embedded plates (EP) of different sizes on ceiling/column/walls for cable tray support & periphery lighting.

Supply of structural steel viz. MS channels/ angles for cable tray support.

( Part-C ) CCTV,ACCESS CONTROL, FIRE ALARM SYSTEM , PAS SYSTEM , NETWORKING AND CABLING Supply and Installation of Radiation monitoring instruments

Supply of Area Gamma Monitors range (0-100 mR/hr) as per the specification attached

Supply of Low range Area Gamma Monitors /Gate monitors as per the specification attached

Supply of dual hand, foot, clothing monitor (dual) as per the specification attached

Supply of Palm alpha monitors as per the specification attached

Supply of Portable alpha Alscin monitor as per the specification attached

Supply of Personal contamination monitor (alpha + beta) as per the specification attached

Supply of Dual continuous air monitors (alpha + beta) as per the specification attached

Supply of alpha counting System as per the specification attached

Supply of Beta counting System as per the specification attached

Supply of contamination cum survey meter as per the specification attached

Installation and commissioning of part-C items (135.1 to135.10)

Supply and Installation of Control and Instrumentation

Supply and installation of DP transmitters as per the attached technical specification

Standalone, PLC system with 32 or more Digital input, 32 or more Analog inputs (Differential ended), 16 or more digital outputs ,Scada license, RIO modules, Modbus TcP/IP master Communication modules, Back plane, connecting cables and all required accessories/Hardware as per the attached technical specification

Supply and installation of CCTV system and access control system

Supply of PTZ IP cameras as per the specification

Installation and commissioning charges for PTZ IP camera.

Supply and Installation of fixed dome cameras as per the specification

Supply of Fixed Ip cameras as per the specification

Installation and commissioning of Fixed Ip cameras

Supply of 32 channel NVR as per the specification

Supply and installation of 55" CCTV surveillance display monitor with necessary wall mounting accessories

Supply of HDMI/Display port adaptor(Gold plated) with the video cable suitable for above display with length of minimum 10 meter for interfacing graphics card to display station

Installation, commissioning, testing of HDMI/Display port adaptor(Gold plated) with the video cable suitable for above display with length of minimum 10 meter for interfacing graphics card to display station

Supply of Desktop type CCTV Client workstation with 32" LED display monitor

Installation, commissioning, testing of Desktop type CCTV Client workstation with 32" LED display monitor

Fabrication, supply, installation and commissioning of full height single Lane Stainless Steel Turnstile gate, fixed SS Grill above turnstile, spares, its associate cabling (specification attached)

Supply of RFID card Reader (MIFARE) and Accessories.

Supply, installation, testing & commissioning of Fire alarm system

Supply, installation, testing & commissioning of addressable intelligent microprocessor-based fire detection and alarm control panel complying to EN54/VDS (2 LOOPS)

Supply, installation, testing & commissioning of digital Linear heat sensing (LHS) cable.

Monitoring and Control module with enclosure for Linear heat sensing (LHS) cable having two elements for LHS circuit.

End of line resistor with interface module, enclosure, etc for Linear heat sensing (LHS) cable.

Supply and laying of 660V grade 1P x 1.5 sq.mm twisted pair copper conductor PVC insulated FRLS PVC inner and outer sheath armoured red outer sheath cables on surface including clamping/cleating on structure/floor/ceiling/wall/tray, etc as required.

Supply, installation, testing & commissioning of Wall mounted loop powered hooter with addresable sounder base and junction or fixing box having minimum sound pressure level of 90dBA basic rating.

Supply, installation, testing & commissioning of analogue addressable (double action) break glass or resettable plastic element type manual call point with inbuilt isolator including base junction or fixing box as required.

PA system, Networking and Field Cable laying, digging & Termination work for Interfacing of field devices and all the above-mentioned (RMS, Instrumentation and CCTV) systems LOUD SPEAKERS

Supply and installation of Wall mounted horn type loud speaker of rated power 15W and maximum power of 22W with sound pressure level of min 114dBA at 15W (1m) complete with ABS/polycarbonate holding box, mounting bracket etc as required.

Supply & Installation of wall mounted Junction Box (PJB) fabricated out of 2mm thick CRCA sheet, punched hole for signal cable (instrumentation FRLS cable) entry on all sides and suitable for incoming cable of size 6pairx0.75 sq.mm. armoured twisted pair cable. The junction box shall consist of 50nos. terminals suitable for 0.75 sq.mm.

Supply & installation of wall mounted Junction box for PA speakers fabricated out of 2 mm thick CRCA sheet, punched hole for conduit entry on all sides and having 4 nos. of terminals, suitable for terminating 0.75 sq. mm PA cable.

Supply and installation of PA amplifier (500 watts)

WIRES, CABLES, CONDUITS AND ACCESSORIES

Supply and drawing of 1PairX0.75 sqmm twisted pair PVC insulated,FRLS PVC outer sheath, stranded copper conductor, flexible cable in surface conduit.

Supply and drawing of 6PairX0.75sqmm twisted pair PVC insulated, FRLS PVC outer sheath, stranded copper conductor, flexible cable in surface conduit.

Supply and drawing of 30PairX0.75sqmm twisted pair PVC insulated, FRLS PVC outer sheath, stranded copper conductor, flexible cable in surface conduit.

Supply and drawing CAT-6 cable from Field instruments to the network switch

Supply CAT6 UTP Patch cords, 1 meter

Installation, commissioning, testing of CAT6 UTP Patch cords, 1 meter

Supply and embedment of 16 SWG black enamelled heavy duty rigid mild steel (MS) ERW conduit pipe of following sizes along with all accessories such as bends, junction box, socket, check nut, etc. including making threads, removing burrs, drawing of fish wire, laying n RCC slab, beam and wall, cutting & laying in brick wall,etc. as required under the instruction of Engineer-in-charge. Deep junction box of min 75mm deep shall be provided in slab.

Supply and drawing 50 Pair 0.5Mm Armoured Jelly filled Telephone Cable

Networking

Supply and installation of POE N/W switch ((8x10/100 Mbps RJ45, 2x1 Gbps SFP port)) with SFP port as per the specification attached

Supply and installation of 9u rack

Supply of Fully Loaded drawout type, LC type 12-port Fiber Distribution(LIU) System of 1U size

Installation, commissioning, testing of Fully Loaded drawout type, LC type 12-port Fiber Distribution(LIU) System of 1U size

Supply of 1 Gbps Single Mode (SFP) 1000BASE-LX LC Module compatible with above supplied switch(5sets=10 nos)

Installation, commissioning, testing of 1 Gbps Single Mode (SFP) 1000BASE-LX LC Module compatible with above supplied switch(5 sets = 10 nos)

Supply LC-LC SM Duplex Fiber Patchcords 1 meter length.

Installation, commissioning, testing of LC-LC SM Duplex Fiber Patchcords 1 meter length.

Supply 6-core Armoured Single Mode (9/125 um) loosely buffered Fiber optic cable

Laying of 6-core Armoured Single Mode (9/125 um) loosely buffered Fiber optic cable

( Part-D ) Mechanical Section-I SUPPLY OF MECHANICAL ITEMS Supply of Centrifugal fans, DIDW backward curved, up blast type complete with motor, protection equipment, base frame, belt guard, flexible connection at inlet & outlet, vibration isolators etc. of capacity 50,000 m3/hr @ static pressure 75 mm WG and as per the technical specifications. Casing, impeller, base frame, etc. shall be epoxy painted.

Supply of Centrifugal fans, SISW backward curved, up blast type complete with motor with necessary protection equipment, base frame, belt guard, flexible connection at inlet & outlet, vibration isolators etc. of capacity 55,000 m3/hr @ static pressure 200 mm WG and as per the technical specifications. Casing, impeller, base frame, etc. shall be epoxy painted.

Supply of Isolation dampers (butterfly type): – for ventilation fan inlet & outlet with flexible metallic sealing to ensure leak tightness of minimum 99.8%, Double acting Rotary type pneumatic actuator for the following sizes as per the specifications:

1400x 1100 x 300 mm (Supply & Exhaust Fan outlet)

Dia. 1600mm x 300 mm (Exhaust Fan Inlet)

1500x 1500 x 300 mm (Main Exhaust Duct Damper)

Dia. 1200mm x 300 mm (Exhaust filter bank Inlet)

Supply of SS304L Leak tight doors for filter banks of Exhaust system as per the specification.

a) Size: 900 x 2200mm

a) Size: 750 x 1250 mm

Section-II SITE INSTALLATION, FABRICATION, TESTING & COMMISSIONING OF MECH. ITEMS Installation, Testing and Commissioning of Centrifugal Type ventilation supply & exhaust fans along with motor, protection equipment, base frame, belt guard, flexible connection at inlet & outlet, vibration isolators etc. of capacity 50000 m3/hr @ static pressure 75 mm WG (2 Nos.) and Capacity 55,000 m3/hr @ static pressure 200 mm WG. (2Nos) capacity as per technical specification and site requirement.

M.S. Support for ducts, plenums, structural supports, ducts stiffeners, bracings along with epoxy primer and epoxy painting (angle/ channel / plate/ pipe / rod / fasteners/ E.P etc.). Supply of materials, fabrication and installation as per the specification and site condition.

Installation of Butterfly type isolation dampers – for fans inlet / outlet, duct along with necessary MS support structure as per the specification and site condition. (support material & fabrication cost is paid separately as per item no.2)

Supply, fabrication & Installation of Exhaust system SS 304L filter retainer frame (5x3 module) for Pre and HEPA filters onto the E.P.'s provided in RCC filter bank as per the specification and site condition.

Supply, fabrication & Installation of Supply system Mild Steel filter retainer frame (5x3 module) for Washable filters in supply fan room as per the specification and site condition.

Supply, fabrication and installation of Louvers & SS wire mesh bird screen along with its mounting frame as per the specification and site condition.

Supply Duct (GI, 20G, Grade 120 gm/m2 Zinc Coating): Preparation of fabrication drawings/site erection drawings, Procurement of material, fabrication, installation, complete with supports out of angles / channels /rods, anchor fasteners wherever required, GS nuts, bolts, gaskets, testing, painting, brick wall opening and as per the specification and site condition. This cost will be based on the weight of actual GI sheet used. However, support material & its fabrication cost will be paid separately as per item no.2.

M.S. 3 mm thick return air duct, Preparation of fabrication drawings /site erection drawings, Procurement of material, fabrication, welding, DPT, installation complete with supports out of angles / channels / rods, anchor fasteners wherever required, all welded joints with its support, testing, painting, brick wall opening and as per the specification and site condition. This cost will be based on the weight of actual MS sheet used. However, support material & its fabrication cost will be paid separately as per item no.2.

M.S. 5mm thick plenum / riser, Preparation of fabrication drawings / site erection drawings, Procurement of material, fabrication, welding, DPT, installation complete with supports out of angles / channels /rods, anchor fasteners wherever required, all welded joints with its support, testing, painting, brick wall opening and as per the specification and site condition. This cost will be based on the weight of actual MS sheet used. However, support material & its fabrication cost will be paid separately as per item no.2).

SS 304L, 3 mm thick, ducting near the outer boundary of building, stiffeners: Preparation of fabrication drawings / site erection drawings, Procurement of material, Fabrication, welding, DPT, installation along with its support, testing, painting, brick wall opening and as per the specification and site condition. This cost will be based on the weight of actual SS 304L sheet used. However, support material & its fabrication cost will be paid separately as per item no.2).

Flow balancing dampers for supply and exhaust ducting (Al powder coating with gear operated manual operated): procurement, installation, testing and as per the specification and site condition, Cost is based on area of the duct in which damper is installed.

Supply air grilles with opposed blade volume control dampers (VCD), (18 G thk. blade Al with powder coating): procurement, installation, testing and as per the specification and site condition, Cost is based on the neck area of the grill.

Return air grilles with opposed blade volume control dampers (VCD) and MOC as 1.6 mm thk MS with powder coating: procurement, installation, testing and as per the specification and site condition. Cost is based on the neck area of the grill.

Supply and installation of Propeller Fans complete with motor, cables, installation frame, wall cowl etc and electrical wiring with plug top from the nearest socket point for fans as per the specification and site condition.

15 NB threaded nozzle with metallic cap on supply and exhaust duct / Plenum as per requirement.

Supply of GI Coated anchor fasteners as per standard specifications (Size M12 x minimum length 110mm, HSL-3G Type or Fischer model FH-II.

Supply, Installation and testing of Instrumentation and control for ventilation system as per TTS and approved documents and drawings.

Functional testing of ventilation system as per tender technical specification

Supply and installation of Split Air conditioner unit: 2 TR as per the specifications.

DIPAK S PIMPLE ENGINEERS AND CONTRACTORS (BID ID -3166718)

Shubham EPC Private Limited (BID ID -3166839)