PROVN OF GUARD REST ROOM ALONGWITH TOILET FACILITY NEAR FOOTBALL GROUND POST PROVN OF FOUR PARKING SHEDS AREA 144 SQM SPECIAL REPAIR TO ROOF TREATMENT OF BLDG NO P 96 AT 35 FD REGT AT MADUKKARAI LOCATION AND PROVN OF CHAIN LINK FENCING AT NORTH CAMP

Amount

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard/ dense soil complete all as specified and as directed.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sq m on plan and not exceeding 1.5m depth and getting out in hard/ dense soil complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick each layer in hard/dense soil complete all as specified and directed

Removing of excavated soils not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

M&L for PCC 1:4:8 type - D2 (using 40mm graded stone aggregate) as in foundations filling and mass concrete complete all as specified and as directed.

M&L for reinforced cement concrete (nominal mix) Type B1, 1:2:4 using 20 mm graded stone aggregate as in foundations, including rafts, footing, foundations, beams, plinth beams, bases for columns, etc., basement slabs, under reamed piles and mass concrete etc complete all as specified and directed.

M&L for use and waste of formwork to sides of concrete foundations, footings, base of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work; vertical or to batter flat surface rough finished complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) Type B1, 1:2:4, using 20mm graded stone aggregate as in columns, pillars, piers, posts and struts all as specified and directed.

M&L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions with rough finished surface of concrete complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) Type B1, 1:2:4, using 20mm graded stone aggregate for beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for use and waste of steel formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. fair finished surfaces of concrete flat complete all as speicified and directed.

M&L for reinforced cement concrete (nominal mix) 1:2:4 type B1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and directed.

M&L for use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick column, beam etc (Horizontal or sloping) rough finished all as specified and directed.

M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floors and roofs not exceeding 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work all exceeding 10cm wide and not exceeding 20cm wide with rough finished surfaces complete all as specified and as directed.

M&L for reinforced cement concrete (nominal mix) Type B1, 1:2:4, using 20mm graded stone aggregate as in chajjas and the like etc., complete all as specified and directed.

M&L for use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges etc., fair finished flat surface complete ll as specified and directed.

M&L for mild steel TMT bars 10mm dia and over grade Fe-500/500D, cut to length, bent to shape as required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and directed.

M&L for mild steel TMT bars 6mm to 8mm dia of grade Fe-500/500D and over cut to length, bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

M&L for mild steel TMT bars 5mm dia and over Fe-500/500D cut and upto and including 10mm dia stirrups, spacers and binders, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.90mm dia or securing with clips all as specified and directed.

M&L for extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exc 15cm but n.exc 30cm in width or girth, including cutting to edges, mitred and stopped ends etc., complete all as specified and directed.

M&L for plain cement concrete type B1, 1:2:4 (using 20mm graded stone aggregate) as in coving, plinth courses, coping and the like including weathering, slightly rounded or chamfered angles and throating including necessary form work, complete all as specified and directed.

M&L for Moorum / Red bajri filling in floors or pavings laid in layers not exceeding 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L hardcore of broken stone or boulders of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface all as specified and directed.

M&L for pre-cast cement concrete block masnory with solid block exceeding 10cm in width and setting in mortar 1:6 type C1 1:3:6 type - C1 using 20mm graded stone aggregate complete all as specified and directed

M&L for pre-cast cement concrete block masnory with solid block not exceeding 10cm in width and setting in mortar 1:4 type C1 1:3:6 type - C1 using 20mm graded stone aggregate complete all as specified and directed

M&L for 10 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 5mm thick rendering in cement mortar 1:4 mixed with water proofing compound over 10 mm thick rendering (backing coat) in cement mortar 1:6 as on (external surfaces) of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed. Note : Water proofing compound shall be measured and paid seperately.

M&L for 5 mm thick rendering in cement mortar 1:3 to ceiling on fair faces of concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for 100mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base of flooring / hard standing and finished even and fair including necessary formwork complete all as specified and directed.

M&L for 25mm thick cement concrete type B1 1:2:4 (using 20mm graded stone aggregate) as in floorings and pavings etc finished even and smooth without using extra ement complete all as specified and directed.

M&L for Non-skid coloured ceramic tiles 7 to 8mm thick (square / rectangle) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick cement screed bed in CM 1:4 complete all as specified and directed.

All as per Item No 34 here-in-before but as on vertical surfaces such as dado/skirting over 10mm thick in CM 1:3 as backing coat with coloured glazed ceramic tiles complete all as specified and as directed.

M&L for white coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for coloured glazed ceramic tiles as in vertical surfaces of size 450mm x 350 x 7to 8mm/350mm x 250mm x 7mm to 8mm thick as in dados, skirting, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigments to match the surface, including 10mm thick rendering in cement mortar 1:3 for fixing dado tiles complete all as specified and directed.

S&F of solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specification and drawing all as specified and directed.

S&F of factory made solid panel PVC door shutter 30mm (Stile) consisting of frame made out of M.S tubes for top and bottom rails M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheets to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame all as specified and directed.

S&F pressed steel frames of size 125x60 mm for doors with one or more rebates including necessary fixing lugs, lock strike plate etc, and filling with PCC 1:2:4 Type - B0 including necessary formwork complete all as specified and directed.

M&L for second class HW plain, framed, panelled shutters 35mm thick (any No of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkats complete all as specified and directed.

M&L for 35mm thick second class hardwood glazed and skeleton door shutters open rebated and prepared to receive glass, gauze etc, (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, sizes of members of shutter as specified in SSR Part-I section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed. Note: Glazing and gauze will be measured and paid separately.

S&F steel windows with side hung shutters incl projecting type hinges with steel handles and steel pegs stay complete with glazing bars dovetailed or welded with glazing bars all as shown on drg complete all as specified and directed.

S&F steel windows with side hung shutters incl projecting type hinges with steel handle complete with out glazing bars dovetailed or welded as fly proof shutters complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay fixed including welding complete all as specified and directed. (Box type frame and shutters.)

M&L for applying two coats of oil bound distemper over a coat of alkali resistant priming paint including prepration of new plastered or unplastered surfaces of walls complete all as specified and directed bythe Engr-in-charge.

M&L for three coats of white wash on ceiling surfaces including preperation of new plastered surfaces complete all as specified and directed bythe Engr-in-charge.

M&L for applying two coats of cement based paint over a coat of primer including prepration of new plastered or unplastered surfaces of walls complete all as specified and directed bythe Engr-in-charge.

M&L for preparation of new steel surfaces of any description not otherwise specified over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description not otherwise specified over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for 4mm thick figured glass, pin headed type and glazing with oil putty in squares not exc. 0.5 sqm in each pane complete all as specified and directed.

S&F chimney bars (stright or camber) bearing bars, tongues or water bars for window frames, window guard bars, plain, let in and fixed independently in steel frames, L or T section supports for shelves etc., including welding and similar articles conforming to Fe-290 Gde E-165 complete all as specified and as directed.

S&F Aluminium anodized barrel tower bolt of extruded section and fixed 200mm length complete all as specified and directed.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F MS Butt hinges medium weight cold rolled mild steel 100mm long complete all as specified and directed.

S&F aluminum handles, cast type ,anodised extruded section 150 mm long complete all as specified and directed.

M&L for providing plain cement concrete type C1 1:3:6 using 20mm graded stone aggregate as in bed blocks for holdfasts including necessary formwork complete all as specified and directed.

M&L for treating ends of posts, back of chowkats etc, area tarred exceeding 0.10 Sqm but not exceeding 0.50 Sqm each including preperation of the surfaces and treated with coal tar or black bituminous paint complete all as specified and directed.

M&L for sanding newly tarred surfaces with clean sharp sand complete all as specified and as directed.

S&F Vitreous China Wash down water closet pan (Pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed.

S&F PVC low level flushing cistern 10 litres capacity, valveless, syphonic action type, white, with inlet ball valve, float and handle including connecting to bracket complete all as specified and directed.

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

M&L for PVC connection 15mm size with PTMT nuts of length 750mm complete all as specified and as directed.

S&F bib tap 15mm dia fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F pillar taps, fancy type, 15mm dia cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F stop valves 15mm dia bore, cast copper alloy screwed down high pressure fancy type, chromium plated with crutch or butterfly handle,screwed both ends for iron pipe or unions and complete all as specified and directed.

S&F tubular towel rail 20mm dia, 600mm long between flanges, D type brass chromium plated fancy type with brackets complete all as specified and directed.

M&L for 20mm bore unplasticised PVC pipes including fittings of pressure rating 10 Kgf/cm² laid and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M&L for 15mm bore unplasticised PVC pipes including fittings of pressure rating 10 Kgf/cm² laid and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks, ISI marked three layer (cylindrical vertical with closed top) hoisted and fixed in position, 1000 ltrs capacity complete all as specified and directed.

S&F of ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed of size 20mm dia (minimum weight 142gms) complete all as specified and directed.

S&F in 20 mm dia nipple of PTMT, suitable for HDPE water tank, min weight 45 gms, complete as as specified and as directed.

S&F of harrison rails of anodised aluminium alloy in repairs fixing with brackets, stops, rollers etc complete all as specified and as directed.

S&F vitreous china wash basin, white, flat back, size 550 x 400mm including brackets and waste coupling including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

M&L for PVC (SWR) gully traps 125 x 110mm, setting and jointing with solvent cement including concrete pedestal etc complete all as specified and directed.

M&L for PVC (SWR) Tee any radius, 110mm bore fitted with oval access door complete all as specified and directed.

M&L for PVC (SWR) bends any radius, 110mm bore complete all as specified and directed.

M&L for PVC (SWR) bends any radius, 110mm bore with access door complete all as specified and directed.

S&F PVC (SWR) vent cowl of size 110mm bore dia complete all as specified and directed.

M&L for 110mm bore PVC (SWR) pipes single socketed, with rubber ring joints in any length, fixed to walls / laid in trenches or in floors complete all as specified and directed.

M&L for 75mm bore PVC (SWR) pipes single socketed, with rubber ring joints in any length, fixed to walls / laid in trenches or in floors complete all as specified and directed.

M&L for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

M&L for treating the backfill in contact with foundation at the rate of 7.5 litre of emulsion per square metre of vertical surfaces (Area of the sub structure in contact with backfill shall be measured) complete all as specified and as directed.

M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

M&L for treating the top soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

M&L for treating the soil alongwith the external perimeter of building at the rate of 2.25 liter of emulsion per square metra of the perimeter wall complete all as specified and as directed.

M&L for 75mm thick plain Cement concrete, 1:3:6, type C-2 using 40 mm graded stone aggregate as in plinth protection, hardstanding/path and finished even and smooth without using extra cement complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks, (old size) straight or curved on plan exceeding 6 mtr mean radius built in cement mortar (1:6) for all as specified and directed.

M&L for precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in cement mortar 1:4 complete with joints to match all as specified and directed. Note :- Reinforcement shall be measured and paid separately.

M&L for concrete bed to drain pipes including packing under and haunching against the sides of the pipes after they are laid and tested in cement concrete 1:4:8 type D-2 using 40mm graded aggregate for 110mm bore PVC (SWR) pipe complete all as specified and directed.

M&L for Precast hume pipe septic tank for 25 users capacity and of dia 1.2mtr, length 2.40mtr including transportation, excavation, returning filling and removal of surplus soil etc., complete and all as specified and as directed by the Engr-in-charge.

Fixing of septic tank in position using crane or by any other mechanical means complete all as specified and as directed.

M&L for 900mm dia and 1.5m depth precast soakage well including transportation, excavation, returning filling/removal of surplus soil and fixing etc.,complete all as specified and as directed.

Excavating in post holes (or similar holes) each in hard /dense soil not exceeding 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm thick, watering and removal of excavated materials to a distance not exceeding 50mtr and making good surfaces, but depth beyond 1.5m for pole complete all as specified and directed

M&L for plain cement concrete 1:3:6 type - C2 (using 40mm graded stone aggregate) as in post hole foundations filling mass concrete includinh necessary formwork complete all as specified and as directed.

M&L for plain cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) 50mm thick as in foot path, floors and pavings etc., surface finished even and fair including necessary formwork complete all as specified and directed.

M&L for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and directed.

M&L for steel work in square/rectangualr tubular trusses/vertical members/purlins, fencing post, etc. including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St.-240 etc con- forming to Fe.290.Gde-E-165 including painted one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication all as specified and directed.

M&L for plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment con- forming to Fe.290.Gde-E-165 complete all as specified and directed by the Engr-in-charge.

M&L for purpose made mild steel bolt 75mm long 12mm dia with hexagonal or square head one end screwed the other or screwed both ends each screwed is to be fitted with washers and one hexagonal or square nut complete all as specified and as directed by the Engr-in-charge.

Supply only chain link fencing PVC coated (1mm thick coat) exceeding 2 Kg per Sqm but not exceeding 3.5Kg per sqm with size of mesh 50x50mm and thickness of wire not exceeding 2.83mm complete all as specified and as directed.

Fixing only PVC coated chain link fencing including fixing of line wires any mesh, size and type of standards, rails, straining bolts etc including provision of binding wires complete alla specified and as directed.

S&F galvanised 2 starnd steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of atandard rail straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc complete all as specified and as directed. (Each line of wire to be measured seperately.)

Dismantling/Taking down existing hessain base felt or clay tiles or any other water proofing treatment from roof/chajja including dismantling existing old padding concrete of any thickness over the RCC roof slab other than beams, chajjas, staircase etc by chipping of with proper tools viz., chisel and with applying reasonable force so as to avoid any famages to exusting RCC roof slab and remove the dismantled debris to a distance exceeding 1.50Km but not exc 5Km to outside the MD land etc complete all as specified and as directed by the Engr-in-charge.

M&L for 40mm average thick cement concrete type -B0 1:2:4 using 12.5mm graded stone aggregate as in levelling course/padding course on top of roof slab, projection on similar surfaces with existing slope complete all as specified and as directed.

M&L for rendering 10mm thick cement plaster in CM 1:3 on fair faces of brick or concrete surfaces finished even and smooth with WPC @ 200ml Per cement bag etc., curved well at the junction of wall & slab before laying of APP membrane complete all as specified and as directed. Note : Supply only WPC will be measured and paid seperately.

M&L for water proofing treatment using 4mm thick APP modified water proofing membrane as per IS 1654-2017/IS 16532-2017 consisting five layer membrane with features as specifed weighing not less than 4.5Kg per Sqm with Non-woven polyster matt black finished weighing not less than 160gm/Sqm having softening point not less than 140 degree celsius longitudinal tensile strength not less than 300 N/sqcm laid over a coat of cold applied bituminous primer @ 0.4ltrs per Sqm on surface. The APP modified membrane is laid by torching applications incluiding sealing the overlap while torching with 100mm on length side and 100mm on width side as per manufacturer's instructions and provide a finishing coat with solar reflective bituminous aluminium paint @ 0.1Kg/Sqm as prescribed by the manufacturer complete all as specified and as directed. Note : The water proofing work shall be carried out by the authorised applicator of original manufacturer.

M&L for point wiring with multistranded copper conductor 1.5 sq mm nominal cross-sectional area single core, PVC insulated and unsheathed FRLS cable 1100 Volts grade, ISI-694 marked with valid CML No. in and including medium grade, PVC conduit pipe and accessories on wall/roof/floor etc, ISI marked with mild steel/pressed steel sunken box (with earth dolly) duly painted with two coats of anti corrosive paint/aluminium paint over a coat of red oxide primer internally. and two coats of black bituminous paint over a coat of red oxide primer externally, covered with 3 mm thick plastic laminated sheet cover for fixing of switches, socket and fan regulators etc, including PVC insulated multistranded copper conductor 1.5 sq mm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth duly completed for one light point controlled by one modular switch 5 Amps complete all as specified and directed.

All as per Item No 110 here-n-before but for one fan point controlled by one modular switch 5 Amps.

All as per Item No 110 here-n-before but for one socket outlet 3 pin 5 Amps on independent board.

All as per Item No 110 here-n-before but 4 Sqmm PVC insulated and PVC unsheathed copper multi stranded conductor cable and 4 Sqmm multi stranded conductor for earth wire for 3 pin 15 Amps power point complete.

M&L for switch Piano flush type 5 Amps single pole one way 240V, 50Hz AC, ISI marked complete all as specified and directed

M&L for switch socket combination 2 in 1, 5 Amps flush type 240V, 50Hz AC, ISI marked complete all as specified and directed

M&L for switch socket combination 2 in 1, 5 Amps and 15 Amps flush type 240V, 50Hz AC, ISI marked complete all as specified and directed

M&L for stepped socket type electronic fan regulator ISI marked flush type on the existing phenolic laminated sheet etc as required all as specified and directed.

M&L for ceiling rose surface bakelite three terminals 65x25mm PVC/ Polycarbonate isolated body all as specified and directed.

M&L for exhaust fan steel body ISI marked AC single phase, 230V of size 300mm sweep copper winding with blades and frame and louvers and including making opening in brick/stone masonry wall as per requirement at site and making good with cement mortar and finishing/matching with the existing surfaces complete all as specified and directed.

S&F ceiling fans 1200mm sweep 230 Volts, ISI marked with three blades, down rod and with squirrel cage induction motor complete with all other accessories required and all as specified and as directed.

M&L for distribution board double door sheet steel phosphatised powder coated MCB/DB with copper bus bar and neutral link earthing stud (confirming to IS-13032, IS-8623) 4 way SPN surface mounted with 200amps rated bus bar 240Volt matching with the existing surface complete all as specified and directed.

S&F amps rating 240V, 10KA 'C' curve miniature circute breaker (MCB) of following poles and current carrying in the MCB DB complete with connection testing and commissioning SPN 32 Amps complete all as specified and directed.

S&F MCB SP 5 to 32 Amps, 240 Volts, 50HZ AC supply complete all as specified and directed.

S&F LED light fitting 1x20 watt, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED Light fitting mirror type with high out put diffuser 2 feet, 1 x 10watt 220V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanized earth wire of size 4mm dia by means of bolts, nuts, check nuts and washers made out of galvanized iron and earth wire protected by GI pipe light grade 20mm bore and connected to main control baord all as shown in electrical plate No 5 of SSR Part - I connected to earth testing point including necessary excavation in any type of soil, PCC 1:2:4 type -B1 chamber 40mm thick, RCC coverslab in 1:2:4 B1 with 6 mm dia MS bars at 100 c/c, funnel,watering pipe etc.complete all specified and directed including testing on completion.

UNIQUE INDIA CONSTRUCTIONS

Narendran Enterprises

SREE PARABRAHMA CONSTRUCTION

p.chinnasamy