REPAIRS TO ROOF, JOINARY, FLOORING AND OTHER B/R WORKS AT BIKRAM ENCLAVE UNDER AGE B/R-II, GE (SOUTH) UDHAMPUR

Amount

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 Square Metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt ) complete all as specified and directed by Engineer-in- Charge.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.50 square metre and not exceeding 4.0 square metre each, including cutting holes for taking out hold fasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.) complete all as specified and directed by Engineer-in-Charge.

Taking down door shutters of any description exceeding 1 square metre and not exceeding 2 square metre each easing, and adjusting as required and re-fixing in same opening including renewal of screws complete all as specified and directed by Engineer-in-Charge.

Taking down door shutters of any description exceeding 1 square metre and not exceeding 2 square metre each complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description not exceeding 1 square metre each complete all as specified and directed by Engineer-in- Charge.

Pressed steel frames of 1.25 mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete, of frame size 125 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and directed.

Pressed steel frames of 1.25 mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete, of frame size 105 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified and directed.

Factory made, 2nd class hard wood 35 mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

35 mm thick second class hard wood factory made Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars) chamfered or rounded, fitted with cut and mitred beads for securing glass etc. sizes of members of shutters complete all as specified and directed in SSR Pt I Section 8, clause 8.24 (a)

Rolled mild steel work of angle iron as in frames of doors & Cup Board etc conforming to grade Fe 410-O or Fe-310-O complete all as specified and directed.

19 mm thick ISI, termite proof, chemically well pressed, prelaminated particle board exterior grade prelaminated, one side with decorative choice lamination and other side balancing white lamination fixed with screws to frame work for kitchen cabinetstand & cup boards etc includimg 6 mm th teak wood beading all around complete all as specified and directed.

Steel window (box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified and directed. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

All as per ser item No 12 but without glazing bar complete all as specified and directed. Note : (i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge shall be measured and paid separately

Factory made mild steel ventilators box type with upper top hung shutters and bottom fixed type shutters including pintol hinges, steel peg stay and one shop coat of red oxide primer complete all as specified and directed. Note : ( i) The window shall be fabricated as per Drg No CEUZ/TD/1302/2009 Sheet 1/3 to 3/3 (ii) MS fillets, glazing, wire gauge shall be measured and paid separately

Door seal in wooden door/aluminium door complete all as specified and directed. Make : Beeta or equivalent

Magic eye fixed in wooden door complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Mild steel framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; railing; frame work for water tanks and similar work conforming to Fe 290 Gd E-165 complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden or metal frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

3 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete (steel or wooden metal) complete all as specified and directed.

Stainless steel wire cloth 0.36 mm nominal and average width of apreture 1.40 mm and fixed with tinned teaks or wire staple complete all as specified and directed.

Mild steel sliding door bolt plate type 250 mm long stove enamelled black with bright bolt not less 12 mm dia bolt with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, complete all as specified and directed.

Mild steel cold rolled butt hinges medium weight 100 mm log fixed to steel/angle iron frame by welding, if required complete all as specified and directed.

All as per ser item No 23 here in before above but 75 mm complete all as specified and directed.

All as per ser item No 23 here in before above but 50 mm complete all as specified and directed.

Continuous MS piano type hinges 30 mm flap (when opened), bright finish or electrogalvanised complete all as specified and directed.

Mild steel pressed steel handle, oval type, stove enamelled black 150 mm long complete all as specified and directed.

100 mm size hasp and staple safty type aluminum anodized with mild steel hinges pin including bolt to hinge plate and fixed with screw complete all as specified and directed.

2nd class hard wood small fittings such as shaped door & window stops, cleat including all necessary labours, articles not exceeding 200 cubic centimetre each complete all as specified and directed.

150 mm ordinary rat tail rod pattern spring with roller and roller plate (mild steel) including welding to steel frame complete all as specified and directed.

150 mm ordinary rat tail rod pattern spring including roller and roller plate (mild steel) complete all as specified and directed.

Mild steel barrel tower bolts, stove enamelled black, with bright bolt 200 mm long complete all as specified and directed.

Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. Square tube, in opening complete all as specified and directed.

Factory made solid panel PVC door shutter 30 mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width struck inside with solvent cement forstyle and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site complete all as specified and directed.

Preparation of wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Preparation of steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Preparation of new surfaces and applying two coats of distemper oil emulsion on walls over coat of primer complete all as specified and directed.

Preparation on old surfaces and applying two coats of distemper oil emulsion on walls over coat of primer complete all as specified and directed.

Preparation of newly plastered surfaces and applying three coats of white washing on walls complete all as specified and directed.

Providing cement concrete 1:3:6 type C-0 (using 12.5 mm graded crushed stone aggregates) for filling in the pressed steel door frame/hold fast complete all as specified and directed.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

Rendering 15 mm thick on brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.

Screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 laying floor finishes complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Glazed coloured ceramic tiles in dado/ vertical surface (600 mm x 300 mm x 7 mm/450 x 300 x 7 mm thick set and jointed in neat cement slurry and pointed in coloured cement to match the surface complete all as specified and directed.

Non skid coloured ceramic tiles (square/ rectengular) 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18s qm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and directed.

20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

10 mm thick rendering as backing coat on fair faces of brick/concrete surfaces in cement mortar 1:4 and finished even and fair complete all as specified and directed.

Aluminum handles cast type, anodised, 150 mm size complete all as specified and directed.

Aluminum anodised barrel tower bolts of extruded section with 150 mm long bolt complete all as specified and directed.

Galvanised mild steel wire clothcut to size, 0.56 mm nominal dia wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed.

Welding in repairs not exceeding 6 mm thick metal and not exceeding 2.5 cm in length complete all as specified and directed.

Rubber gasket for fixing glass pane complete all as specified and directed.

Glass panes of plain sheet glass 5.50 mm thick of ordinary quality in square exceeding 0.50 sqm each pane complete all as specified and directed.

100 mm size butt hinges, extruded aluminum alloy ISI marked complete all as specified and directed.

Aluminum door closer (aluminum extruded section) hydraullically regulated, designation No 3, universal type, suitable for door shutters of 851 mm to 1000 in width and of weight 61 to 80 kg complete all as specified and directed.

Checking of joinery (wooden/steel) iron/ aluminium mongery, pelmet box, door springs etc requiring carpentry work and carrying out minor repairs such as tightening of screws/nails, fixing glass panes, minor adjustment of joinery, door etc. including petty repairs material like screws/nails, plug etc. to make it functional complete all as specified and directed by Engineer-in-Charge. Note : Any items required to be replaced shall be paid under respective items.

19 mm thick ISI, termite proof, chemically well pressed, prelaminated particle board exterior grade prelaminated, one side with decorative choice lamination and other side balancing white lamination fixed with screws to frame work for kitchen cabinetstand cup boards etc includimg 6 mm th teak wood beading all around complete all as specified and directed. Make:- Win Tuff or its equivalent

100 mm long aluminium anodised hasp and staple complete all as specified and directed.

Providing 50 mm thick cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregates) as in plinth protection laid in alternate bays (not exceeding 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulaton boards/ slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

4 mm thick AC board (designer ceiling) of size 600 mm x 600 mm panel confirming to IS 14862 type-B category three including GI frame work with size of grid 605 mm x 605 mm for seanless ceiling comprises of GI perimeter including all accessories complete all as specified and directed. Make : Charminar/Everst.

Dismantling asbestos cement (corrugated, semi corrugated etc) sheets as in roof covering complete all as specified and directed.

0.50 mm thick steel roof sheets prepainted galvalume having through depth and fixing with self driven suitable GI screws complete all as specified and directed. Make :- JSW/ CRIL (Colour roof India Ltd)/Unimet or its equivalent .

6 mm thick asbestos cement corrugated sheet in roof with two corrugation side lap fixed with J or L hooks complete all as specified and directed.

Providing and injecting Along the external wall below concrete or masonry apron using Antitermite Treatment chemical emulsion @ 2.25 litres per running metre including drilling and plugging holes etc. in apron. complete all as specified and directed by Engr-in-Charge. Note : The treatment work shall be carried through authorised agency only and certificate for the same for waranty shall have to be furnished before submitting payment.

Providing and injecting Antitermite Treatment of soil under existing floors using emulsion @ 1 litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand to match the existing floors complete all as specified and directed by Engr-in-Charge. Note : The treatment work shall be carried through authorised agency only and certificate for the same for waranty shall have to be furnished before submitting payment.

Providing and injecting Antitermite Treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same complete all as specified and directed by Engr-in-Charge. Note : The treatment work shall be carried through authorised agency only and certificate for the same for warranty shall have to be furnished before submitting payment.

Roughening surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @ 3 kg/Sqm including 40 mm thick PCC and 15 mm thick plastering in cement mortar (1:3) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separately). Applying bituminous primer on roof surfaces @ 0.40 ltr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and provide modified polymeric five layred APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polyethylene film. Min wt of membrane will be 3.5 Kg/Sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitument 85/25 @ 1.2 Kg/Sqm blinded with fine sand in dry condition @ 0.5 Kg/Sqm & including two coats of bituminous Aluminium paint complete all as specified and directed by Engr-in-Charge.

Supply only integral water proofing compound complete all as specified and directed.

khajuria builders

RAJ MOHD

PARDEEP SHARMA

VARDHMAN INTERNATIONAL

RAMAN CONSTRUCTION CO

KALSOTRA CONSTRUCTION CO