Phairuang Thenhlum Bolia to Thenhlum

Amount

FORMATION CUTTING & SETTING OUT WORKS

Clearing and grubbing of road land including uprooting wild vegetation, grass, brushes, shrubs, saplings and trees of girth upto 300mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable materials to be used or auctioned, upto a lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness as per technical specification clause 201. (I) By Manual means. (B) In area of thorny Jungle.

Cutting of trees Cutting of trees including cutting of trunks,branches and removal of stumps and root, refilling, compaction of backfilling and stacking of serviceable materials by manual means with all lifts as per technical specification clause 201 (A) Lead upto 100m. (i) Girth above 300mm to 600mm.

Cutting of trees Cutting of trees including cutting of trunks,branches and removal of stumps and root, refilling, compaction of backfilling and stacking of serviceable materials by manual means with all lifts as per technical specification clause 201 (A) Lead upto 100m. (ii) Girth above 600mm to 900mm.

Cutting of trees Cutting of trees including cutting of trunks,branches and removal of stumps and root, refilling, compaction of backfilling and stacking of serviceable materials by manual means with all lifts as per technical specification clause 201 (A) Lead upto 100m. (iii) Girth above 900mm to 1800mm.

Setting Out Construction of reference pillar as per Fig 1600.1 (b) as per drawing and technical specification clause 1602.1

Construction of back pillar as per Fig 1600.1 (c) as per drawing and technical specification clause 1602.3

Construction of Job pillar as per Fig 1600.1 (d) as per drawing and technical specification clause 1602.4

Excavation in soil in Hilly Area by mechanical means including cutting and trimming of side slopes and disposing of excavated earth with a lift upto 1.5 m and a lead upto 20 m as per drawing and Technical Specification Clause 1603.1

Excavation in Hilly Areas in Ordinary Rock not requiring blasting by mechanical means including cutting and trimming of side slopes and disposal of cut materials with a lift upto 1.5 m and a lead upto 20 m as per Clause 1603.2

Excavation in Hilly Areas in Hard Rock requiring blasting by mechanical means, lift upto 1.5 m and disposal of excavated rock upto a lead of 20 m as per Clause 1603.2

Deduct reuseable hard rock @ 15 %

Construction of unlined side drain Earthwork in excavation for structures as per drawing and technical Specification Clause 305.1. including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50m, dressing of sides and bottom and back filling in trenches with excavated suitable material. I. Ordinary soil

Construction of unlined side drain Earthwork in excavation for structures as per drawing and technical Specification Clause 305.1. including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50m, dressing of sides and bottom and back filling in trenches with excavated suitable material. II. Ordinary rock (not requiring blasting)

Construction of unlined side drain Earthwork in excavation for structures as per drawing and technical Specification Clause 305.1. including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50m, dressing of sides and bottom and back filling in trenches with excavated suitable material. III. Hard rock (requiring blasting)

Construction of Lined Side Drain Earthwork in excavation for structures as per drawing and technical specifications clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deletirious material and disposal upto a lead of 50m, dressing of sides

Construction of Lined Side Drain Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications clauses 702, 704, 1202 & 1203. II. Coursed rubble masonry (ii) In 1 : 4 cement mortar

Flexible Pavement Compacting Original Ground. (ii) Compacting original ground supporting subgrade. Loosening of the ground upto a level of 300 mm below the subgrade level, watered, graded and compacted in layers for subgrade construction as per Technical Specification Clause 303.5.2.

Scarifying Existing Bituminous Surface. Scarifying the existing bituminous road surface to a depth of 150 mm and disposal of scarified material with a lift upto 3 m and lead upto 1000 m as per Technical Specification Clause 301.4.

Flexible Pavement Water Bound Macadam (Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density.) ii)Grading- 2

Flexible Pavement WBM Grading 3 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405.

Prime Coat (i) Low porosity Providing and applying primer coat with Bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70- 1.0 kg/sqm using mechanical means as per Technical Specification Clause 502.

Tack Coat Tack coat (Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom)

Mix Seal Surfacing Providing, laying and rolling of close-graded premix surfacing material (Hot Mix) of 25 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification Clause 509 By Mechanical Means (Hot Mix)

Construction of subgrade and earthen shoulder with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compavted to meet requirement of table 300.2 with lead upto 1000m as per technical specification clause 303.1.- Construction of earthen shoulder.

Road marking paint Painting lines, dashes, arrows, etc. on roads in two coats on old work with ready mixed road marking paint conforming to IS:164 on bituminous/concrete surface, including cleaning the surface of all dirt, dust and other foreign matter, demarcation at site and traffic control as per drawing and technical specification Clause 1702 Side line and zebra crossing

Rigid Pavement Water Bound Macadam with Crushable Screenings Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405.

Rigid Pavement Construction of un-reinforced panelled concrete pavement as per design,thickness as per design,Over a prepared sub base,eith concrete strength M30(Grade),Coarse and fine aggregates conforming to IS:383,maximum size of coarse and fine aggregates not exceeding 25mm mixed in a concrete mixer of not less than 0.2cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork spreading the concrete with shovel, rakes,compacted using needle,screed and plate vibrators and finished in continuouse opereation including provision of admixtures approved,curing of concrete slabs for 14-days,including cutting of groove at 1 meter interval in both direction using concrete joint cutting machine

Protection Works Earthwork in excavation for structures as per drawing and technical Specification Clause 305.1. including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50m, dressing of sides and bottom and back filling in trenches with excavated suitable material.

Protection Works Providing concrete for plain/reinforced concrete in open foundation complete as per drawing and technical specification clause 802, 803, 1202 & 1203. I. Pcc grade M10 Nominal mix 1 : 3 : 6 (hand mixing)

Protection Works Stone masonry in cement mortar for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204 II. Course rubble masonry (2nd sort) (iii) in cement mortar 1 : 5

Protection Works Providing and laying filter media with granular crush aggregates as per specification to a thickness of not less than 600mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind retaining wall to the full height compacted to firm condition complete as per drawing and technical specification clause 1204.3.8

Protection Works Stone masonry in cement mortar 1:3 for parapet complete as per drawing and technical specifications Clauses 700 and 1208.4 I. Random rubble masonry

Protection Works Plastering with cement mortar ( 1:4) 15mm thick on Brick/Stone works as per drawing and technical specification clauses 613.4 and 1204

Protection Works Providing PCC M20 architectural coping on the top of retaining wall complete as per drawing and technical specification clause 615,710 and 1204.3.11

HP Culverts Earthwork in excavation for foundation of structures upto 3m depth as per drawing and technical Specification Clause 1104 including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and back filling with approved material.

HP Culverts Providing concrete for plain/reinforced concrete in open foundation complete as per drawing and technical specification clause 802, 803, 1202 & 1203. I. Pcc grade M10 Nominal mix 1 : 3 : 6 (hand mixing)

HP Culverts Stone Masonry Work in cement mortar in foundation of head walls complete as per drawing and technical specification Clause 1109 (A) in 1:4 cement Mortar

HP Culverts Bedding for pipe Type-B (First class) bedding : Laying (First class) bedding of well compacted sand, moorum or approve granular materials as per clause1105 (ii)

HP Culverts Providing and laying RCC Pipe NP3 for Culvert on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection work etc.

HP Culverts Backfilling in abutment, wing wall and return wall complete as per drawing and technical specification I. Granular material

HP Culverts Backfilling in Foundation Trenches as per drawing and technical specification Clause 1108 II. Earth filling

HP Culverts Stone masonry in cement mortar 1:3 for parapet complete as per drawing and technical specifications Clauses 700 and 1208.4 I. Random rubble masonry

HP Culverts Plastering with cement mortar (1:4) 15mm thick on Brick/Stone works as per drawing and technical specification clauses 613.4 and 1204

HP Culverts Providing PCC M20 architectural coping on the top of retaining wall complete as per drawing and technical specification clause 615,710 and 1204.3.11

Slab Culverts Earthwork in excavation for foundation of structures upto 3m depth as per drawing and technical Specification Clause 1104 including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and back filling with approved material. I. Ordinary soil (upto 3m depth)

Slab Culverts Providing concrete for plain/reinforced concrete in open foundation complete as per drawing and technical specification clause 802, 803, 1202 & 1203. II. PCC grade M15 (ii) Nominal mix 1:2.5:5

Slab Culverts Stone Masonry Work in cement mortar for sub-structure complete as per drawing and technical specification Clauses 702, 704, 1202 and 1204. II. Course rubble masonry (2nd sort) (A) in 1:4 cement Mortar

Slab Culverts Providing and laying reinforce cement concrete in super structure as per drawing and technical specifications clause 800,1205.4 and 1205.5 II. RCC M25 grade

Slab Culverts Supplying, fitting and placing HYSD bar reinforcement in super structure complete as per drawing and technical specifications clauses 1002,1010 and 1202.

Slab Culverts Backfilling in abutment, wing wall and return wall complete as per drawing and technical specification clause 1204.3.8 I. Granular material

Slab Culverts Stone masonry in cement mortar 1:3 for parapet complete as per drawing and technical specifications Clauses 700 and 1208.4 I. Random rubble masonry

Slab Culverts Plastering with cement mortar (1:4) 15mm thick on Brick/Stone works as per drawing and technical specification clauses 613.4 and 1204

Slab Culverts Providing PCC M20 architectural coping on the top of retaining wall complete as per drawing and technical specification clause 615,710 and 1204.3.11

Reinforced cement concrete M15 grade kilometre stone of standard design as per IRC : 8 fixing in position including painting and printing, etc. as per drawing and Technical specification clause 1703. i) 5th kilometre stone (precast)

ii) Ordinary kilometre stone (precast)

iii) 200m stone (precast)

Reinforced cement concrete M15 grade boundary pillars of standard design as per IRC : 25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical specification clause 1704.

Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new plastered surfaces as per drawing and Technical specification clause 1701. ( For boundary pillars )

Providing and fixing of retro-reflectorised cautionery, mandatory and informatory sign as per IRC : 67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3 fixed over alluminium sheeting 1.5mm thick supported on mild steel angle iron post 75x75x6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450mmx 450mmx 600mm, 600mm below ground level as per drawing and Technical specification clause 801. (ii) 60cm equilateral Triangle

Providing and erecting direction and place identification retro-reflectorised sign as per IRC : 67 made of encapsulated lens type reflective sheeting vide clause 1701.2.3 fixed over alluminium sheeting 2mm thick with area not exceeding 0.9sqm supported on

Earthwork in excavation for structures as per drawing and technical specifications clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deletirious material and disposal upto a lead of 50m, dressing of sides (ii) Ordinary rock (i) Upto 3m depth

Providing and laying parapet with pcc M15 as per drawing and technical specification clause 800 and 1208.4 (i) Nominal mix 1:2.5:5(Hand Mixing)

Plastering with cement mortar (1:3) 15mm thick works as per drawing and technical specification clauses 613.4 and 1204

PMGSY LOGO

Title in formation

Citizen information

AMC for 1st Year

AMC for 2nd Year

AMC for 3rd Year

AMC for 4th Year

AMC for 5th Year

Laltlanmawia