CA NO. CWE SGNR - 71 OF 2020-21 SPECIAL REPAIRS TO OFFICERS MESS BUILDING NO. P-19 AT MILITARY STATION LALGARH JATTAN

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm in thickness (below or above ground level) complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick / stone walls including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed by Engineer-in-Charge.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

M&L for brickwork with fly ash old size bricks, strait of curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for Vitrified Ceramic tiles 8 to10 mm thick (square/ rectangular) (light shed,Matt finish/Digital)polished, area of each tiles not exceeding 0.36 sqm, in floors etc. over and including 15 mm thick screed bedding in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor complete all as specified and directed by Engineer-in-Charge.

M&L for Vitrified Ceramic tiles 8 to10 mm thick (square/ rectangular) light shed polished, area of each tiles not exceeding 0.36 sqm,on vertical surfaces such as skirting / dados over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor complete all as specified and directed by Engineer-in-Charge.

M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectengular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm in floor over and including 15 mm thick screed bedding in cement mortar 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match the floor complete all as specified and directed by Engineer-in-Charge.

M&L for glazed ceramic (coloured tiles/matt finish) of size 450 x 300 x 7 mm thick on vertical surfaces such as skirting / dados over and including 10 mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed in coloured cement to match the floor complete all as specified and directed by Engineer-in-Charge.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engineer-in-Charge.

M&L for machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid over cement screed base laid over and including 15 mm thick screed bed in cement mortar 1:6, set and jointed with grey cement slurry mixed with pigment to match shade of the slab including rubbing and plishing complete all as specified and directed by Engineer-in-Charge.

M&L for machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over and including 10 mm thick backing coat in cement mortar 1:4 set and jointed in neat cement slurry mixed with pigment to match shade of the slab including rubbing and plishing complete all as specified and directed by Engineer-in-Charge.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed by Engineer-in-Charge.

M&L for rendering, 10 mm thick on brick work or concrete surfaces in cement mortar 1:6 on wall finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering, 15 mm thick on brick work or concrete surfaces in cement mortar 1:4 on wall, finished even and fair including mixing of WPC in mortar complete all as specified and directed by Engineer-in-Charge. Note :- WPC shall be mearured and paid separately

M&L for rendering, 5 mm thick on brick work or concrete surfaces in cement mortar 1:3 on ceiling finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of oil bound distemper over 3 mm thick wall care putty on newly plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment and two coats of oil bound distemper over 3 mm thick wall care putty on plastered surfaces of walls including preparation of surfaces complete all as specified and directed by Engineer-in-Charge.

M&L for three coats of white wash on newly plastered surfaces incl preparation etc. on ceiling complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of white wash on old plastered surfaces incl preparation etc. on ceiling complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of cement base paint on newly plastered surfaces including preparation etc. on wall complete all as specified and directed by Engineer-in-Charge.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded mechanically crushed stone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10 mm wide, 30 mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with bitumen & sand mixture complete all as specified and directed by Engineer-in-Charge.

Dismantling of brick tiles in floor laid dry and pointed in cement morter complete all as specified and directed by Engineer-in-Charge.

Demolition mud in roofs, any thickness, including plastering and leeping complete all as specified and directed by Engineer-in-Charge.

M&L applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per sqm as in roof surface including cleaning surfaces complete all as specified and directed by Engineer-in-Charge.

M & L APP based membrance minimum weighing 3 KG per sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than150 gms/sqm) laid on primed surface by torced application with APP membrane covered with 40mm thick brick tiles (manufactured with canal water) over and including 10mm thick screed bed in CM 1:4 complete all as specified and directed by Engineer-in-Charge. Note : Brick tiles shall be measured & paid separately under respective item of this BOQ

M & L Lime concrete terracing as specified in roof (excluding bitumen tack coat) complete all as specified and directed by Engineer-in-Charge.

M&L 40mm thick brick tiles laid flat on lime concrete & joints grouted flush in cement mortar (1:3) bedded in 15mm th cement morter (1:6) mixed with 5% of crude oil by weight of cement on lime concrete complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 29 here-in-before but for except tiles complete all as specified and directed by Engineer-in-Charge.

M&L PCC 1:2:4 type B-1, using 20mm graded stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges including necessary form work etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for repair to damage RCC coloumns/Beam/Slab by using micro mortar and concrete in Following Stages :- (a) Removing the mortar and loose concrete from RCC elements. (b) Cleaning the rusted reinforcement and applying rust removal. (c) Inserting the additional reinforcement in cape the coves sectional area reduction in more than 20 percent welding the reinforcement with existing area and supporting adequate on walls if required with grout. (d) Providing micro morter and concrete over bond coat to cover the reinforcement and slet surface. (e) Providing adequate from wave and scafolding if required. (f) Curing the surface. Note :- (i) Rust removal, bonding agent, grout, micro morter and concrete and related chemicals shall be of Dr Fixit/BASF and STP (ii) Work is to be got executed from authorised applicator and company. (iii) Steel reinforcement measured and paid separately

M&L providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear meter including drilling and plugging holes etc. in apron complete all as specified and directed by Engineer-in-Charge.

M&L providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment of soil under existing floors using emulsion @ one litrre per hole, 300mm apart including drilling and plugging 12mm dia holes with CM 1:2 to match the existing floors complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames n.exc 1.5 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames exc 1.5 sq. m but n.exc 4.0 sq. m each with shutters (without taking off shutters from the frame) complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 Sqm and n.exc 2 Sqm each complete all as specified and directed by Engineer-in-Charge.

S&F powder coated aluminium frame/shutter for doors, windows, ventilators and aluminium partition with one or more rebates including jointing cleats glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete with locking arrangements for fixing with powder coating on aluminium sections, minimum thickness of powder coating shall be 50 micron as per the specification. The top and bottom horizontal members and vertical members adjacent to wall shall be fixed with floor, ceiling, walls and cills where required and fixed with the help of rawl plugs and screws or with fixing clips or with expansion hold plate fastners. Aluminium section shall be smooth, rust free, straight, mitred and jointed mechanically whereever required complete all as specified and directed by Engineer-in-Charge.

S&F powder coated anodised aluminium window and ventilator shutters, side hung type without sash bar, aluminium sections weighing exc 0.55 Kg/m (1.50 to1.80mm thick) including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (01 No) hinges type B-21 100 mm long (2 Nos) suitable handle (01 No) in each window shutter and necessary accessories as required complete all as specified and directed by Engineer-in-Charge.

S&F Neoprene / EPDM rubber gasket complete all as specified and directed by Engineer-in-Charge. Note : Taken for other than door/window shutter if required

M&L 4.8 mm thick sheet glass, ordinary quality and glazing with aluminium snap beading of any size of glass in each pane with solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and directed by Engineer-in-Charge.

S&F powder coated standard aluminium anodised grill size of mesh 75mm x 75mm and 8mm thick section using U channel 25x12mm complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of Fibre glass Reinforced plastic (FRP) door frame of required built in colour in three legged of cross-section 90mm x 45mm having single ribate of 32mm x 15mm to recieve shutter of 30mm thick including laminated door frame moulded with fire retardant grade unsaturated polyster resin and chopped strand mat(CSM) also door frame laminated shall be 2mm thick and shall be filled with suitable wooden block of 2nd class hard wood in all three legs frame shall be covered with fibreglass from all sides MS stay flat iron 25mm x 3mm shall be provided at the bottom to steady the frame complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of 30 mm thick glass fibre reinforced plastic (FRP) paneled doorshutter conferming to IS:14856-2000 of required colour and made with fire retardant grade unsaturated polyster resin,moulded to 3mm thick FRP laminated for forming hollow rails and style with suitable second class hardwood timber block inside at required places for fixing of fittings,cast molithically with 5mm thick FRP laminated for panels including fixing to frames, complete all as specified and directed by Engineer-in-Charge.

Taking down existing shutter and refixing in same opening shutters of any description exc 1.0 Sqm but not exc 2.0 Sqm each complete all as specified and directed by Engineer-in-Charge. (Note:- 'Refixing' includes taking down, easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc.

S&F 35 mm thick 2nd class hard wood factory made plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer-in-Charge.

S&F 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed by Engineer-in-Charge.

S&F 100 mm long butt hinge, extruded aluminium alloy with galvanised mild steel hinge pin, anodized and fixed type B-21 complete all as specified and directed by Engineer-in-Charge.

S&F 200 mm long aluminium anodised barrel tower bolt, of extruded sections complete all as specified and directed by Engineer-in-Charge.

S&F 125 mm long aluminium anodised handle, cast type complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm long extruded aluminium alloy handle, fabricated type anodised complete all as specified and directed by Engineer-in-Charge.

S&F 100 mm long butt hinge, medium weight, cold rolled mild steel complete all as specified and directed by Engineer-in-Charge.

S&F 300 mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed by Engineer-in-Charge.

S&F for 300mm long aluminium alloy, anodised, sliding door bolt type not less than 16mm dia fixed complete all as specified and directed by Engineer-in-Charge.

S&F as 300mm ordinary rat tail rod pattern springs including roller and roller plate mild steel fixed complete all as specified and directed by Engineer-in-Charge.

M&L providing kitchen cabinet in required sizes at site made out of 18mm thick one decoative lamination sheet consisting of Careass 18mm thick PVC & provision of shutters made out of 18mm thick one side decoative laminated PVC sheet all required brackets 5.5 screws etc for PVC 18mm Celluca Ply (Prelaminated) for shutters. The Panels shall be fabricated using adhesive and screws where ever required. All the edges shal be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification mentioned as drawing and specification complete all as specified and directed by Engineer-in-Charge.

M&L providing kitchen cabinet in required sizes at site made out of 18mm thick one decoative lamination sheet consisting of Careass 18mm thick PVC & provision of shutters made out of 18mm thick one side decoative laminated PVC sheet all required brackets 5.5 screws etc for PVC 18mm Prelaminated Stainless Steel for frame, partition, shelves etc. The Panels shall be fabricated using adhesive and screws where ever required. All the edges shal be covered with 2mm thick edge bonding tape or 90 degree edge bent finish as per make and specification mentioned as drawing and specification complete all as specified and directed by Engineer-in-Charge.

S&F telescopic drawer slides channel - zink plated complete all as specified and directed by Engineer-in-Charge.

S&F stainless steel soft close crank hinges suitable size and shape as required complete all as specified and directed by Engineer-in-Charge.

S&F magnetic catcher fixed with nut, screw and washer complete all as specified and directed by Engineer-in-Charge.

M&L Plywood grade BWP 12MM Thick type BB, Fixed with screws to timber frame work includng decorative laminate 0.9mm thick type 1of surface finish coloured and pattern as approved fixed with approved adhesive as per manufacturer's instruction complete all as specified and directed by Engineer-in-Charge.

S&F continuous (Piano) hinges width of flaps (when open) 40mm, brass, bright finish or electro galvanised complete all as specified and directed by Engineer-in-Charge.

S&F steel reinforcement of TMT bars of size 10mm dia and over, cut to length, bent to shape as required including cranking, hooking ends & binding with mild steel wire (annealed) not less than 0.090mm dia complete all as specified and directed by Engineer-in-Charge.

M&L for reinforced cement concrete, type B1 1:2:4 using 20 mm graded stone aggregate in lintels upto 1.5m span, cills steps, seismic and other similar bands, plinth courses, copings, bed plates, and the like including weathering, slightly rounded or chamfered angles and throating, incl formworks complete all as specified and directed by Engineer-in-Charge. Note : Reinforcement shall be measured and paid seperately.

M&L for form work to soffits of suspended slabs such as roof slabs, n. exc. 20cm thick (horizontal or sloping for fair finished concrete surface complete all as specified and directed by Engineer-in-Charge.

S&F Dholpur stone cladding 16 to 18 mm thick gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.25 Sqm but n exc 0.50 sqm fixed with and including 15 mm thick backing coat in cement mortar 1:4, making V groove at top and bottom of stone and drilling hole for hold fastener, polishing, rubbing & including silicon treatment complete all as specified and directed by Engineer-in-Charge.

S&F 40 mm dia, cupboard/drawers knobs with nut, screw and washer of brass, polished complete all as specified and directed by Engineer-in-Charge.

S&F 100 mm extuded, bars handles, fabricated type polished for cabinet shutters complete all as specified and directed by Engineer-in-Charge.

S&F stainless steel wire cloth 0.63 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 69 here-in-before but for fixing in repairs complete all as specified and directed by Engineer-in-Charge.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in squares n. exc. 0.5 Sqm in each pane complete all as specified and directed by Engineer-in-Charge.

S&F 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed by Engineer-in-Charge.

M&L preparation of new or previously untreated wooden surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M&L preparation of old painted wooden surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

S&F drapery rods, coloured, standrad quality, powder coated not less than 25mm dia with heads at both ends and middle support, rings, etc. complete all as specified and directed by Engineer-in-Charge.

S&F in repair coloured vitrieous china WC (European type) wall mounted cascade wall with push type flushing in wall including all necessary fitting like CP brass push type flushing in wall, flush pipe, connection to trap and to flushing pipe etc complete making good to wall complete all as specified and directed by Engineer-in-Charge.

S&F in repair coloured seat cover for water closet (European type) complete all as specified and directed by Engineer-in-Charge.

S&F in repair vitreous china wash hand basin coloured table top bowl type of size 380x380mm, long screwed shank fly nut flange end including cutting for and pinning in granite slab of hole including 32mm dia chromium plated waste coupling and bottle trap complete all as specified and directed by Engineer-in-Charge.

Supply and fix in repairs central pillar tap for wash hand basin two in one duly hot and cold marked complete all as specified and directed by Engineer-in-Charge.

S&F in repair bib tap 15mm bore cast copper alloy chromium plated long body fancy type with capston head and cup screwed down, hand operated, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge.

S&F in repair chromium plated fancy type health faucet with 1mtr tube & hook complete all as specified and directed by Engineer-in-Charge.

S&F in repair brass chromium plated Liquid soap dispenser including fixing to 15mm bore pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repair corner glass shelf 200mm with Abs brackets complete all as specified and directed by Engineer-in-Charge.

S&F in repair brass chromium plated PEG SET 6 including fixing to 15mm bore pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repair chromium plated fancy type soap dish complete all as specified and directed by Engineer-in-Charge.

S&F in repair stainless steel grating round or square 150mm size (minimum weight 100gms) complete all as specified and directed by Engineer-in-Charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

S&F in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed by Engineer-in-Charge.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engineer-in-Charge.

S&F in repair tubular towel rail, Brass chromium plated 20 mm dia, 'D' type, 60cm long between flanges complete all as specified and directed by Engineer-in-Charge.

Dismentling of water tanks of capacity exc 500 and n.exc 1000 ltrs and removing from site complete all as specified and directed by Engineer-in-Charge.

S&F rotational moulded polythene water storage tank 1000 ltr capacity, tripple layers in white colour, vertical with closed top hoisted and fixed in position all as specified in SSR part-I complete all as specified and directed by Engineer-in-Charge.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20mm bore complete all as specified and directed by Engineer-in-Charge.

S&F in repair ball valves, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball scewed for iron pipe and fixed, (Minimum weight 20 mm-210 gms) in 20mm dia bore pipe complete all as specified and directed by Engineer-in-Charge.

Taking down 15 mm dia steel GI tubing including all connected fittings of any dia and in any position including cleaning for re fixing the serviceable pipe complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 95 here-in-before but for 20mm dia pipe complete all as specified and directed by Engineer-in-Charge.

S&F 15 mm dia galvanised steel tubing medium grade including necessary fittings like sockets, tees, elbows, reducers, unions etc fixed to walls / ceiling complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 97 here-in-before but for fixing only with new fittings complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 97 here-in-before but for 20mm dia pipe complete all as specified and directed by Engineer-in-Charge.

Taking down eaves gutters and rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-necks etc., including cleaning or refixing or removal to Store complete all as specified and directed by Engineer-in-Charge. Note : measured overalll as fixed along the cente line over fittings and accessories

S&F 110 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls complete all as specified and directed by Engineer-in-Charge.

S&F 75 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm dia PVC (SWR) vent cowl complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm bore PVC (SWR) branch piece double (single Y) equal or unequal complete all as specified and directed by Engineer-in-Charge.

S&F 110 mm dia PVC (SWR) bend any radius complete all as specified and directed by Engineer-in-Charge.

S&F 75 mm dia PVC (SWR) bend with access door any radius complete all as specified and directed by Engineer-in-Charge.

S&F PVC (SWR) floor trap, 75 mm dia with grating including jointing with solvent cement etc complete all as specified and directed by Engineer-in-Charge.

S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flangesof 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approximate 900 mm centreto centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed by Engineer-in-Charge.

S&F Seamless calcium silicate ceiling made out of 1800 x 1200 mm size 12MM Thick board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish complete all as specified and directed by Engineer-in-Charge. Note : Frame work for ceiling shall be measured and paid separately

S&F Roof tiles of mangalore pattern interlocking at side joints, laid dry complete all as specified and directed by Engineer-in-Charge.

M&L for Framed work as in doors or gates of hollow section (Square / rectangle) with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings including hold fast, locking arrangement incl wheel track and sliding door bolt as required and hanging; also fastening and fixing complete all as specified and directed by Engineer-in-Charge.

S&F Gumti (base size 50cm x50 cm) and height not less then 60 cm made of dhulmera (bikaner) stone including carving work as per design approved by GE complete all as specified and directed by Engineer-in-Charge.

Surface excavation n. exc. 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge.

Removing excavated materials n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed by Engineer-in-Charge.

M&L for precast cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in kerb stones size 300mm x 300mm x 100mm with plain fair faces, including chamfers, weathering, throating etc setting in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

M&L for 100mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base below floors complete all as specified and directed by Engineer-in-Charge.

M&L Machined pressed precast concrete interlocking paver block glossy with grey cement and pigment, any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade with over 50mm thick Fazilka sand cushion complete all as specified and directed by Engineer-in-Charge.

M&L for filleting in any position and to any shape in cement mortar 1:4 including all mitres, stops, etc section of fillet n.exc. 25 sq. cm complete all as specified and directed by Engineer-in-Charge.

S&F bath tub with all necessary fittings and fixtures of size 1670 x 760 x 400mm including front panel, side panel and supporting structure complete all as specified and directed by Engineer-in-Charge. Model : Cat part No. B2521101 , B2521104 , B2522101 (a) Diverter Body Hi Flow (Cat Part No. F4030101) (b) Diverter Plate (Ruby) (Cat Part No. F1005721) (c) Spout - Tipton (Cat Part No. F1005662) (d) Hand Shower (Cat Part No. F7030103) (e) Shower tube with holders (Cat Part No. F8070401) (f) Shower 8 Inches (Cat Part No. F7010102) (g) Shower rod 24 Inches (h) Bath tub jali (Cat Part No. F8050501)

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete including fittings such as switches, ceiling rose, pendent holder, sketch fitting, sockets, regulator etc and making good distrubed surfaces of walls and floors etc to match with the existing complete all as specified and directed by Engineer-in-Charge.

M&L point wiring with 1.5 Sqmm (nominal cross section area) PVC insulated unsheathed multistranded copper conduct cable in and including medium grade rigid PVC concealed conduit in wall after cutting chases in wall including cast iron or pressed steel terminal box covered with and including 3 mm thick bakelite sheet top cover fixed flush with wall using brass screws, washers and 1.5 Sqmm single core PVC insulated unsheathed copper conductor wire as earth continuity to common earth and connecting to earth dolly for one light point controlled by one switch and making good diturbed surfaces complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 121 here-in-before but for one three pin 5 Amps socket outlet with 2 pin out let of 5 Amps on independent board complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 121 here-in-before but for controlled with two No. two way switches complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 121 here -in- before but for point wiring with 4 sqmm multi stranded conductor cable and 4 sqmm unsheathed copper conductor earth wire for two in one 6 pin 15 Amps socket outlet on independent board complete all as specified and directed by Engineer-in-Charge.

Supply & fixing switch piano type flush button single pole one way 5/6 Amps, 230 volts complete all as specified and directed by Engineer-in-Charge.

Supply & fixing socket outlet 3 pin 5 Amp,flush type complete all as specified and directed by Engineer-in-Charge.

Supply & fixing socket outlet two in one, 6 pin 5 Amp and 15 Amp flush type complete all as specified and directed by Engineer-in-Charge.

S&F for switch piano flush type 15 Amps one way complete all as specified and directed by Engineer-in-Charge

Supply & fixing ceiling rose surface bakelite 65 mm x 50 mm size, 3 terminals complete all as specified and directed by Engineer-in-Charge.

Supply & fix in replair batton integrated LED light fitting 1x18 W aluminium LED Channels pre wired for LED tube fixed to roof/ceiling /wall with necessary wooden/PVC blocks etc and connecting with 2 core flexible PVC insulated multistranded copper conductor from ceiling rose to fitting including taking down old one complete all as specified and directed by Engineer-in-Charge.

S&F in repair LED down lighter recessed, circle in square shape with aluminium PDC body, Luman 100 / watt complete all as specified and directed by Engineer-in-Charge.

S & F LED wall bracket light with lamp holder including 9 watt LED lamp complete all as specified and directed by Engineer-in-Charge.

Sub main wiring with two single core PVC sheathed insulated cable of 6 sqmm size copper multi stranded conductor 1100 volts grade drawn-through and including 25 mm dia stove enamelled rigid steel conduit of adequate size of conduit and junction boxes, terminal boxs and accessories such as tees, bend elbows, reducers, bell mouth tube ends fixed concealed in wall including one run of 6 sqmm copper conductor unsheathed multi stranded earth wire earth continuty conductor. (Two run of single core cable and one run of 6 sqmm copper wire earth continuty conductor and conduit with accessories shall be measured as one length) complete all as specified and directed by Engineer-in-Charge. -------------------------------------------------------------------------- Note : A sum of Rs. 38,800.00 will be deducted on account of credit for dismantled/ demolished / taken down material. Please refer details on Srl Page No. 30 & 31 (Schedule of Credit) of Tender document

PAREEK AND COMPANY

Aggarwal brothers and company