MISC CERTAIN REPAIR IN BLDGS, CLEANING AND REPAIR OF SEWAGE LINES AND REPAIR TO ELECTRICAL INTERNAL WIRING, PUMP SET, STREET LIGHT, AIR CONDITIONE (AC) AT CHAUHTAN HILL UNDER GE (AF) UTARLAI

Amount

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified.

M&L for 10mm thick rendering in CM 1:6 on stone masonry surfaces and finishing the surface even and smooth without using extra cement complete all as specified.

M&L for 15mm thick rendering in CM 1:4 on stone masonry surfaces and finishing the surface even and smooth without using extra cement complete all as specified.

M&L for complete removal of existing treatment on walls and applying two coats of oil bound distemper over and including 3mm thick wall care putty complete all as specified.

M&L for two coats of oil bound distemper on newly plastered walls including necessary preparation of surfaces over and including 3mm thick wall care putty complete all as specified.

M&L for two coats of cement base paint on newly plastered surfaces of walls including necessary preparation of surfaces complete all as specified.

Demolition of cement concrete of any type description and in any position complete all as specified.

M&L for 75mm thick PCC (1:4:8) type D-2, using 40mm garded stone aggregates as in sub base complete all as specified.

M&L for 25mm thick PCC (1:2:4) type B-0, using 12.5mm garded stone aggregates as in base concrete to floors finished even and fair complete all as specified.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premises complete all as specified.

M&L for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles laid over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for non-skid ceramic tiles 7 to 8 mm thick (square/rectangular), coloured tiles, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match shade of tiles laid over and including 15mm thick screed bed in CM 1:6 finished even and fair complete all as specified and directed.

M&L for Non-skid Ceramic tiles 7 to 8 mm thick (square/ rectangular), coloured tiles, area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match shade of tiles laid over and including 15mm thick screed bed in CM 1:6 finished even and fair complete all as specified and directed.

M&L for Glazed ceramic tiles in vertical surface 350 x 250 x 7 mm /450 x 350 x 7 mm thick (glossy finish) on walls/vertical surfaces laid over and including 10mm thick rendering in CM 1:4 finished even and fair, complete all as directed.

Taking up or down steel tubing and connection including cleaning for refixing of 15 mm bore complete all as specified.

-ditto- as per item Ser No 15 above but 20 mm bore pipe complete all as specified.

Refixing old steel tubing and connections in new or old position as in walls, ceiling floors etc bore of pipe 15mm complete all as specified.

-ditto- as per item Ser No. 17 above but 20mm bore pipe complete all as specified.

S&F 15 mm dia galvanized steel tubing, "medium grade", with all fitting and fixed complete to walls celling or laid in floors complete all as specified and directed.

-ditto- as per item Ser No.19 above but 20mm bore pipe complete all as specified.

S&F in repairs Vitreous China wash basin, white, flat back, size 550x400mm including S&F of 15mm bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed, including waste coupling and brackets complete all as specified.

S&F in repairs PVC waste pipe of 32mm bore of 900mm length for WHB & Sink complete all as specified.

S&F in repairs grating doom 100mm dia of PTMT (min weight 25 gms) complete all as specified.

S&F in repairs Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms) complete all as specified.

S&F in repairs bath room cabinet 350 x 450mm Make : Prayag, Commander, Polytuff complete all as specified.

S&F in reapirs 15mm bore two ways angle cock capstan head cast copper alloy chromium plated screwed down high pressure complete all as specified.

S&F in repairs 15mm bore brass CP wall mixer mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified.

S&F in repairs Brass chromium plated health faucet with necessary arrangements complete all as specified.

S&F in repairs stop valves cast copper alloy fancy type, chromium plated screwed down high pressure with crutch or butterfly handle for 15mm bore complete all as specified.

-ditto- all as per item Ser No 29 but cup concealed type complete all as specified

S&F in repairs brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified.

S&F in repairs 15mm bore bib taps cast copper alloy, chromium plated, facncy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified.

S&F in repairs 15mm bore pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified.

S&F in repairs brass chromium plated shower rose 125mm size complete all as specified.

S&F in repairs 25mm bore (medium weight) Stainless steel curtain rod bright finish of best quality complete all as specified

S&F in repairs stainless steel brackets for 25mm dia stainless steel curtain rod of best quality complete all as specified

S&F in repairs stainless steel fancy knob end cap for 25mm dia stainless steel curtain rod complete all as specified

S&F in repairs Vitreous China squatting pan, `Orrisa' pattern, size 580 x440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified

Taking down chowkats or frames with shutters (without taking off shutters) n exc 1.5 sqm each complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters) exc 1.5 sqm but n exc 4sqm each complete all as specified.

S&F factory made solid PVC door frame of size 50 x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification complete all as specified

S&F Factory made solid panel PVC door shutter 30mm thick (stiles) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap inserted for top rail and bottom rail. Penelling of plain colour PVC sheet to be fitted to the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at site complete all as specified

S&F 35 mm thick factory made, second class hard wood, plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part - I), kiln seasoned and chemically pressure treated complete all as specified.

S&F 35 mm thick factory made second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24(a), supplied and fitted to chowkats complete all as specified.

S&F factory made steel windows with side hung shutters including box type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded complete all as specified.

S&F factory made steel windows with side hung shutters including box type hinges with steel handle and steel peg stay complete without glazing bars complete all as specified.

S&F mild steel of grade Fe-290 (Grade E-165) in framed work such as grills, grating etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders etc and similar works complete all as specified.

S&F rolled mild steel of grade Fe-290 (Grade E-165) in rolled section as in frames for doors/windows, framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc complete all as specified.

S&F 300 mm long mild steel sliding door bolts, clip type, stove enameled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified.

S&F 150 mm size mild steel pressed handles, oval type, stove enameled black complete all as specified.

S&F 200 mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified.

S&F floor door stopper, with 140 mm long cover plate, of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor complete all as specified.

S&F Butt hinges,100 mm size extruded aluminium alloy with galvanised mild steel hinge pin,anodised & fixed type B-22 complete all as specified.

S&F Aluminium tower bolts of extruded section of size 150mm complete all as specified.

S&F extruded aluminium alloy handles, fabricated type, anodized of size 100 mm complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads or from metal frame glazed with putty including punching or drilling out old glazing pin/spring, clips and providing new ones complete all as specified.

S&F sheet glass 3 mm thick, ordinary quality and glazing with oil putty or wooden beads in square n.exc. 0.5 sqm in each pane complete all as specified.

S&F in repairs stainless steel wire cloth, 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or wooden beads supplied with shutters complete all as specified.

S&F stainless steel wire cloth, 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or wooden beads supplied with shutters complete all as specified.

M&L for preparation of old surface of walls including pillars etc (plastered or unplastered) by scrapping down smoke soot moulds, moss and efflorescent salt and greasy oil and greasy spots and applying one coat of white wash complete all as specified

-ditto- all as per item Ser No 60 above but one coat of white wash on ceiling complete all as specified.

M&L for preparation of of old surface of walls including pillars etc by washing rubbing down and scrapping of distempered and painted surfaces and applying one coat of distemper oil emulsion complete all as specified and as directed.

M&L for preparation of old wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint of any tint complete all as specified and as directed.

M&L for preparation of old painted surfaces of iron steel works of any description over 10 cm width or girth and applying one coat of synthetic enamel paint of any tint complete all as specified and as directed.

M&L for one coat of cement base paint on old surfaces of walls including necessary preparation of surfaces complete all as specified.

Excavation in post holes (or similar holes) each n.exc 0.5 Cum getting out, returning filling in and ramming with earth around in layers n.exc 25 cm thick, watering and removing surplus soil to a distance n.exc 50 mtr and making good surfaces in Soft/ disintegrated rock complete all as specified.

M&L cement concrete (1:3:6) type C-2 using (40 mm graded stone aggregate) as in boundry pillars, posts (including caps and bases) complete all as specified

S&F in repairs mild steel work as in posts and struts n fencing including cutting tops in shape as directed drilling holes, notching for wire etc complete all as specified.

M&L for two coats of synthetic enamel paint on steel surfaces or surface of any description over one coat of red oxide over 10 cm in width or girth not otherwise described including preparation of surfaces complete all as specified.

S&F in repairs galvanised, 2 strands, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolt including securing or tying at crossings with and provision of galvanised mild steel wire staples or steel pins etc complete all as specified.

Dismantling of stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc complete all as specified and directed.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified.

M&L PCC Block masonry with solid block exc 10cm in width in PCC 1:3:6 type C-1 using 20mm graded stone aggregate and setting in CM 1:6 complete all as specified.

Cleaning and removing all scale and dirt etc from storage water tanks of capacity exc 250 ltrs but n exc 500 ltrs including cleaning of mouths of circulating pipes by applying bleaching powder and brushing with wire brushes taking out all scales etc cleaning of tank with fresh water, flushing out disinfecting of tank with potassium permaganate 2% solution till stored in tank become clear complete all as specified and as directed

S&F Rotational moulded polythylene water storage tank of capacity 500 litres (Cylindrical, Vertical with closed top) hoisted an fixed in position and painting the tank with two coats of heat resistant paint including dismantling of the old unserviceable water tank complete all as specified and directed. Note : PVC tanks shall be ISI marked and having two layers.

S&F in repairs 20mm bore Ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed compete all as specified and directed Note : Minimum weight of ball valve shall be 210 gms

Taking down old broken cover and M&L PVC threaded coller with PVC cover fitted on PVC water tank with help 4 Nos PVC nut & bolt suitable for 500 & 1000 ltrs capacity water tank complete all as specified

-ditto- as per item No 77 above but tank of capacity 1000 ltrs complete all as specified

M&L for one coat of heat resistance paint on existing painted surface over head PVC tank over 10 Cm width or grith complete all as specified

S&F in repairs 10 litres capacity, cast iron, valveless, syphonic action type, flushing cistern, high level, with intlet, ball valve, float, chain and pull, and brackets complete all as specified.

M&L for rendering 15 mm thick in CM (1:4) on stone masonry surfaces finished even and smooth without using extra cement with using integral water proofing compound as per manufacturer's instructions complete all as specified. Note: Integral Water Proofing compound shall be measured and paid for separately as “Supply only”.

Supply only integral water proofing compound ISI marked.

M&L for precast reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, shelves and similar articles with plain faces, set in CM 1:4, including necessary form work moulds and dismantling etc complete all as specified. (Reinforcement shall be measured and paid for separately).

M&L for mild steel TMT bars 6 mm to 8 mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.

Labour only for cleaning pipe lines 150mm dia by rodding from Man holes and well flushing with water after cleaning complete all as specified & directed. Note:- Contractor shall be depute his supervisor to collect complaint from AGE(B/R)-II office at 9.00 am to 5.00 pm & after cleaning the line get checked from Engineer-in-Charge.Complaint of blockages should be completed with in 24 hrs, if the same is not attended, a recovery of Rs 250/- per complaint shall be made.

-ditto- all as per item Ser No. 85 above but 100mm dia complete all as specified.

Labour only for Clearing of blockage of Nahani Trap of bath room, kitchen by rodding blockage including taking down/refixing of grating etc complete all as specified and directed by Engineer-in-Charge. Note- Contractor shall depute his supervisor to collect complaint from AGE(B/R)-II office at 9.00 am to 5.00 pm & after cleaning the line get checked from Engineer-in-Charge.Complaint of blockages should be completed with in 24 hrs, if the same is not attended, a recovery of Rs 250/- per complaint shall be made.

Labour only for Clearing of blockage of gully trap of bath room, kitchen by rodding blockage including taking down/refixing cover complete all as specified and directed by Engineer-in-Charge. Note- Contractor shall depute his supervisor to collect complaint from AGE(B/R)-II office at 9.00 am to 5.00 pm & after cleaning the line get checked from Engineer-in-Charge.Complaint of blockages should be completed with in 24 hrs, if the same is not attended, a recovery of Rs 250/- per complaint shall be made.

Labour only for Clearing of blockage of Indian type WC/ Europion type WC by rodding/ pumping by hand including taking out door/refixing of over access covers etc complete all as specified and directed by Engr-in-Charge. Note:Contractor shall depute his supervisor to collect complaint from AGE(B/R)-II office at 9.00 am to 5.00 pm & after cleaning the line get checked from Engineer-in-Charge.Complaint of blockages should be completed with in 24 hrs, if the same is not attended, a recovery of Rs 250/- per complaint shall be made.

Labour only for Cleaning of manholes of size n.exc 1.00 Mtr plan area (internal) and n.exc 1.00 Sqm depth from GL including removal of manhole covers carefully, cleaning of sludge etc and refixing the manhole covers with cement mortar (1:4) (Sluge shall be removed outside MD land)

Pumping out sewage water/sludge from existing septic tank/soak well of any size & capacity and removal the sludge to out side MD land

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified.

M&L for Point wiring with PVC insulated unsheathed copper stranded conductor single core cable (FRLS) of 1.5 Sqmm size with and including drawn through PVC casing & caping fixed on walls/ceilings with PVC terminal box fixed on wall with 3mm thick plastic laminated sheet cover for fixing switch/sockets/regulators etc complete with 1.5 Sqmm PVC insulated copper conductor single core cable (FRLS) as earth continuity conductor connected to common earth dolly for the following:-

One light point controlled by one switch

One ceiling fan/exhaust fan point controlled by one switch

One 5 Amps socket point on independent board.

S&F switch 5 Amps piano flush type single pole one way

S&F switch socket combination flush type 5 Amps, 2/3 pin multipurpose

S & F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings

S & F switch socket combination outlet 2 in 1, 3 pin 5 Amps and 15 Amp flush type (Multi purpose) piano type AC 230 Volts complete all as specified.

S & F electronic fan regulator, 250 V, flush type, on the exiting phenolic laminated sheet etc. as reqd complete all as specified.

S & F ceiling rose 65x50mm two to three terminal AC 230 volts complete all as specified.

S&F LED light fitting, 18 /20 Watt, 6000K decorative ultra slim LED tube fixture with extruded heat shrink environmental friendly energy efficient complete with all accessories pre wired and including taking down old u/s fittings and connecting up with three core flexible copper conductor cable with suitable size complete all as specified & directed by Engr- in - Charge.

S&F LED, two feet,white LED light fitting 9/10 Watt 6000Kdecorative ultra slim along with linear LED Tube lighting fixture with extruded heat shrink environmental friendly energy efficient complete with all accessories pre wired and including taking down old u/s fittings andconnecting up with three core flexible copper conductor cable with suitable size complete of all as specified & directed by Engr-in-Charge.

S & F of Building security lights LED type 25 W pressure die cast aluminium housing luminaires including provision of GI bracket and taking down old u/s fittings and complete all as specified & directed by Engr-in-Charge.

S&F recessed mounted LED light fitting (2 X2 ft) size for POP/modular /gypsum ceiling fitting 45 Watt 6000K with highly translucent wide window opal diffuser envirmental pre wired and including taking down old u/s fittings and connecting up with three core flexible copper conductor cable with suitable size complete all as specified

Dismantling all components of ceiling fan 1200/1400mm sweep, cutting and removing burnt out copper winding from the rotor assy and rewinding with super enamelled copper winding wire of suitable guage and turns with necessary insulation materials, varnishing, reassembling, greasing to bearings, replacing bushes, replacement of capacitor and complete testing including taking down and refixing the ceiling fan complete all as specified Note : a) The spares like ball bearing, capacitor required for repair the fan will be measured and paid seperetely under respective items. b) Expendable stores like cotton waste/cleaning materials, grease, lubricants, machine screws, safety split pin, bolt/nuts and transportation to and fro from site to work place are deemed to be included in rate quoted.

Supply and fix the following spares for repairs to fans :-

Ball bearing suitable for ceiling fan

Capacitor 230 volts, 50 Hz, 2.5 mfd

Replacement of rubber shackle and split pin with galvanised clamp complete with nuts, bults washer.

S&F in repairs of 2 core flexible PVC copper wire for connecting from ceiling rose to capacitor complete all as specified

Supply and fixing in replacement MCB SP, 6 to 32 Amps 10 KA single pole AC 230 volts curve 'C' complete all as specified

Supply and fixing in replacement MCB SPN 6 to 40 Amps 10 KA AC 230 volts curve 'C' complete all as specified

S&F in replacement Sheet of metal enclosures for fixing MCBs Single pole and neutral 8 ways, 240 volts with 200 Amps rated bus bar with double door fixed on flush to the wall including making the hole in the wall and fixing the DB including cement work and plastering complete all as specified and directed.

S&F in replacement Sheet metal enclosures for fixing MCBs Single pole and neutral 4 ways, 240 volts withe 200 Amps rated bus bar withe double door fixed on flush to thee wall including making the hole in the wall and fixing thee DB including cement work and plastering complete complete all as specified and directed

S & F in repairs for submain wiring with 2 runs of 4.0 sqmm single core PVC insulated stranded copper conductor cable (FRLS) drawn through rigid non metallic PVC casing & caping with one run of 2.5 Sqmm PVC insulated copper conductor cable (FRLS) as earth continuity conductor and necessary connections complete all as specified and directed Note : 2 runs of 4.0 sqmm PVC insulated unsheathed copper conductor and 1 run of 2.5 sqmm PVC insulated unsheathed copper conductor and 1 run of PVC casing caping of suitable size will be measured as single run

M & L in replacement for Earthing complete with 600x600x6.00mm thick GI earth plate electrode burried directly in ground not less than 2.25 mtr below GL with the top edge of the plate at a depth not less than 1.5 mtr from GL, connected to GI earth lead of 4.0 mm dia by means of nuts, bolts, washers, checknuts, made out of galvanised iron or steel,(as shown in electrical plate No 03) earth wire protected by galvanised iron pipe, connected to main switch board complete including necessary earth work,excavation,PCC chamber, watering pipe, funnel, wiremesh, RCC chamber cover etc all as specified and directed.

S& F in replacement switches Air Break, Gang operated of 11000 volts Triple pole, mechanically operated, mounted on insulator and steel frame, with operating mechanism worked from ground level, for current rating upto 400 Amps complete all as specified

S&F in repairs Lightning arresters expulsion type complete with all fittings, transmission class, discharge capacity 65 kilo amp suitable for 11000 volts complete all as specified

S&F in repairs Expulsion fuse single pole upto 25Amps complete all as specified

S&F in replacement disc type insulator, porcelain, vitreous 145mm high and 255mm dia ball and socket type, white, brown or green Single disc assembly for tension with tension clamps for conductors, working pressure 11000 volts complete all as specified

S&F in replacement pin type, porcelain, vitreous, white, brown or green insulator including one galvanised mild steel spindle, two galvanised iron washers and one galvanised iron nut, 150mm height, 150mm dia for 11000 volts grade complete all as specified

M & L in replacement for earthing complete with 600x600x6.00MM thick GI steel earth plate electrode burried directly in ground not less than 2.25 mtr below GL with the top edge of the plate at a depth not less than 1.5 mtr from GL, connected to GI earthstrip size 32X6mm all shown in electrical plate No 03 by means of nuts, bolts, washers, checknuts, made out of galvanised iron or steel, earth wire protected by galvanised iron pipe, connected to main switch board complete including necessary earth work,excavation,PCC chamber, watering pipe, funnel, wiremesh, RCC chamber cover etc complete all as specifiedand directed.

Supplying, fixing and testing of Street lights LED type 60 /70W pressure die cast aluminium housing luminaires complete including taking down of old unserviceable light fittings complete all as specified & directed by Engr-in-Charge.

M&L for bracket for street light fitting made out of 40 mm bore pipe GI tube "light grade" bent to shape required, fixed with and including MS flat iron clamps, bolts, nuts, washers complete including taking out old UNSV complete all as specified and directed by Engr -in - charge.

Supplying,fixing and SMC box fixed on street lights pole with MCB SPN and neutral busbar all as specified complete including taking down of old unserviceable SMC box complete all as specified & directed by Engr-in-Charge.

Supplying , fixing and testing in replacement of timer switch 32A 2 pole/230V analogue time switch with connecting items fixing on pole/wall/panel complete all as specified

S&F in repairs MCCB 4 pole, 415 V, adjustable type 100 Amps with breaking capacity 25 KA including necessary modification in the panel complete all as specified and directed.

S&F in repairs MCCB 4 pole, 415 V, adjustable type 63 Amps with breaking capacity 25 KA including necessary modification in the panel complete all as specified and directed.

M&L for Repair & Calibration of Fuel Pump & Injectors as per calibration procedure and norms including replacement of unserviceable 'O' rings, Plungers and cups etc. for the 15 KVA of DG Set complete all as specified.

Repair of Self Starter including re-winding of Commutator, replacing Carbon bush set, carbon bush holder, King Pins Holders, armature check nuts, body screws, clutch plate assembly and solenoid etc. as required for the 15 KVA of DG Set complete all as specified

M&L for De-scaling of radiator by dismantling the upper & lower tank and cleaning the core pipes with cleaning suitale chemicals, components and arrest the leaking core by brazing/ dummy with lead including cleaning of upper and lower tanks and replacing the upper and lower gaskets and required nuts, bolts, refixing the same including testing and painting complete all as specified and directed for the 15 KVA of DG Set

M&L for Maintenance and servicing of alternator of 15 KVA DG set by opening the end cover, cleaning the dust and rust formed over the terminals, cleaning with CTC liquid up to the satisfaction and checking of diodes , excitation winding, isolating transformer and AVR panel, removing of dust from strips/ winding by using blower upto satisfication insulation resistance complete, and refixing the covers and testing complete all as specified and directed.

Supply and install in replacement ON LOAD change over switch 415V 4 pole of capacity 100 Amps in and including sheet metal enclosure complete all as specified and directed.

Supply in replacement and top up engine oil 15W 40 or as per manufacturers recommendations.

M&L for maintenance to15 KVA Gen Set for 'B' check after 06 months or 250 hrs running, whichever is earlier as per the recommendations of manufacturer including renewing of necessary filters, Engine oil etc, complete all as per manufacturers instructional manual and complete all as specified and directed by Engr-in-Charge. Note : Engine oil will not be supplied under Sch 'B' for carrying out 'B' check.The quoted rate deemed to be included for the same.

M&L for maintenance to100 KVA Gen Set for 'B' check after 06 months or 250 hrs running, whichever is earlier as per the recommendations of manufacturer including renewing of necessary filters, Engine oil etc, complete all as per manufacturers instructional manual and complete all as specifieda and directed by Engr-in-Charge. Note : Engine oil will not be supplied under Sch 'B' for carrying out 'B' check.The quoted rate deemed to be included for the same.

M&L for maintenance to 320 KVA Gen Set for 'B' check after 06 months or 250 hrs running, whichever is earlier as per the recommendations of manufacturer including renewing of necessary filters, Engine oil etc, complete all as per manufacturer's instructional manual and complete all as specified and directed by Engr-in-Charge. Note : Engine oil will not be supplied under Sch 'B' for carrying out 'B' check.The quoted rate deemed to be included for the same.

Supply, install, testing and comissioning of maintenance free battery 12 V, 120 AH including copper terminal lugs and including taking down old unserviceable battery complete all as specified.

Supply & Laying in trenches or fixing on wall or passing through pipe or in cable ducts, 1100 volts grade XLPE insulated armoured, electric power cables (heavy duty) with aluminium conductor including taking out old UNSV cables, sand/stone patti covers of the following size complete all as specified. Note: The rate quoted inclusive of termination at ends with suitable aluminium lugs whereever required

50 sqmm 3.5 core

25 sqmm 4 core

16 sqmm 4 core

Excavation in trenches not exceding 1.5m wide and not exceding 1.0 sq m on plan and not exceding 1.5m depth and getting out any type of soil complete all as specified and dirceted.

Returing, filling in, including spreading, leveling, watering and well ramming in layer not exceding 25 cm thick as in soil complete all as specified and dirceted.

Removing excavated material not exceding 50 m and depostingwhere directed at a level not exceding 1.5 m above the starting point complete all as specified.

M & L for sand cushioning all around the cable for protection by natural tibba sand complete all as specified Note: Punned depth of sand cuishoning shall be measured and paid

S&F in replacement of cable jointing kit for 11000V grade cable for outdoor terimination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured Aluminium conducter cable of size 70 sq mm complete all as specified.

S&F in replacement of cable jointing kit for 11000V grade cable for outdoor terimination heat shrink type joint complete with jointing material and accessories suitable for 3 core XLPE armoured Aluminium conducter cable of size 95 sq mm complete all as specified.

Supplying and Laying stone patti 40-50 mm thick, 25- 30 cm wide abutting each other for cable protection complete all as specified

Supply and topping up of transformer oil with di-electric strength not less than 50 KV in to the conservator tank/ body tank of the transformer complete all as specified & directed by the Engineer-in-Charge.

Filtration of transformer oil in transformers/ FRMUs installed at various locations to achieve di-electric strength not less than 50 KV at 2.5mm gap as per relevant IS with portable filtration plant, testing of the oil for the di-electric strength before filtration and after filtration complete all as specified & directed by the Engineer-in-Charge.

M&L for repair of Diesel Engine by dismantling the Sub-assemblies such as fuel pump, fuel injection, wood ward Governor, radiator, oil cooler, engine heads, rocker arms, self starter, dynamo-engine wiring, terminal contacts and safety controls etc. cleaning by suitable cleaning agent, drying, lubricating and re-assembling the sub-assemblies after carrying out necessary minor repairs including testing and commissioning complete all as specified and directed by Engineer-in-charge for the capacityof 15 KVA, DG set. Note : New spare parts will be measured & paid separtely under relevant items.

Material & replacement the parts/ spares for DG set 15 KVA capacity as under:-

Standard liner

Piston assembly

Carban bush

Thurst washer

Valve pair

Valve seal

Valve guide

Ring set

Push rod Kit

Set of rubber ring

Fly wheel ring

Oil seal few

Oil seal

Set of joints

Avmtg assembly

VR Toe

Main bearing standard

CR Bearing

Head gasket

Head bolt,

Fuel filter

Oil filter

AVR Assembly

Air cleaner

Coolent

S&F steel water tubing GI "medium grade" ISI marked with all fittings laid in trenches /wall etc complete for the following sizes including taking out old uerviceable pipe lines complete all as directed by Engr -in- Charge :-

25 mm bore

50 mm bore

80mm bore

S&F Gun - metal, globe or gate valve ISI marked with iron wheel head, screwed at both ends for iron for the following sizes including taking out old un serviceable gate valves complete all as specified and directed by Engr -in- Charge :-

25 mm dia bore

50 mm dia bore

Repair to single phase electric monoblock pump 2 HP installed in pump house with the following works :- (a) Transportation of burnt motor to civil electric work shop. (b) Dismantling of motor, cutting and taking out burnt stator winding from motor cleaning the stator and rewinding with super enameled copper wire of original gauge / size including tapping varnishing, drying, painting, assembling, to fixing of base plate,nut bolt complete and carrying to site including necessary connection, commissioning and testing for 6 hours on full load (Major spare parts will be measured and paid separately under respective items) Note :- Cost of minor spare parts deemed to have been included inquoated rates by the tenderer.

Supply and replacing of following under mentioned worn out U/S parts of centrifugal 3 HP pumping set

Pump shaft for pumping set incl machining threading making key slot etc.

CI impeller

Gland bush

Guide spider complete with bush

Base Plate with bush including nutbolts

Ball bearing

Repair and servicing of RO water plant 150 ltr per hr installed in ORs Mess with the following works :- (a) Replace the UV filter with assembly . (b) Dismantling of RO unit and cleaning RO water storage tank,membrane ,removing inlet/outlet pipe and replace the Chemical tube complete servising and cleaning the unit complete all as directed by Engr-in- charge Note :- (i) Cost of unserviceable spare parts deemed to have been included in coated rates. (ii) Makes of spares parts of RO water plant shall be as existing make/specification.

M&L for attending to break down of GI pipe of 50mm dia GI pipe line from Chautan Base UG sump to hill top UG sump including necessary site clearence, excavation, dewatering the water accumulated at site, removal of broken pipe pieces of various lengths through gas cutting/manual cutting as per site requirement and inserting same size of pipe as per existing site design, necessary PCC work including testing for the leakage pipes complete all as specified and directed by Engineer-in-Charge. Note: GI pipe 50mm dia shall be measured and paid seperately

M & L for servicing of Split type type AC of capacity 1.5 /2 TR of any by cleaning of filter on front side including fins, checking of refrigerant standing pressure, topping of refrigerant upto the required level, complete all as directed by Engineer-in-Charge. Note : Refrigerant required for topping (R22 /407a) shall be maesured and paid for separately

Replacement of following unserviceable item in split type AC :-

Blade for condensing fan motor of capacity 1.5 /2.0 TR

Foam type insulating flexible pipe & air tight outer tapping fitted on ACs of any capacity for suction / discharge copper tubes complete all as directed by Engr-in-charge.

Condensing fan motor of capacity 1.5/2.0 TR

S&F in repairs condenser coil of split type AC of 1.5/2.0 TR capacity of make Carrier / Hitachi / Voltage / Blue star, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs blower fan moter split type AC of1.5/2.0TR capacity of make Carrier / Hitachi / Voltage / Blue star, complete all as specified and directed by Engineer-in-Charge.

S & F in repairs starting capacitor, for split type AC of capacity 1.5/2.0TR. Complete all as specified and directed. Make : EPCOS /ASIAN /Sarada

S&F in repairs Rotary type Compressor (Sealed Unit) of split type air conditioner of capacity 1.5/2.0 TR, Single phase 220 volt of existing make necessary modification of foudation as required to suit the compressor, vacumisation, pressure testing, leakage rectification complete to taking down old unserviceable compressor the entire satisfaction of Engr-in-charge.

S&F in repairs scroll type Compressor (Sealed Unit) of Deep freezer 500ltr capacity single 220 volt of existing make including necessary modification of foudation as required to suit the compressor, vacumisation, pressure testing, leakage rectification testing complete to taking down old unserviceable compressor the entire satisfaction of Engr-in-charge.

Supply and filling of Refrigerant gas R 22/ R-134/ R-410(a) in company sealed cylender of capacity complete all as specified and directed by Engr-in-charge

S & F replacement of sheet metal enclosure industrial type 230 Volts with MCB SP 20 AMP complete all as specified.

S&F in repairs wall mounted indoor Voltage Stabilizer automatic operation single phase and designed for input variation between 170 V to 250 Volt with output voltage stabilized at 230 V with accuracy of ±2.5% and of capacity 4 KVA complete all as specified

S & F in replacement of indoor unit 1.5 /2.0 TR capacity as per existing makes and sizes complete all as specified and directed by Engr -in- charge

S & F in replacement of Canopy made out of MS angle iron 60x 60 x 6 mm with GI sheet roofing of suitable size for 2 / 1.50 Ton Cap split A/C Condenser unit duly fixed on window slab/ out side external wall/ building roof of on ground with proper hold fast with PCC 1:2:4 type B-1 using 20mm graded stone aggregate. complete all as specified and directed.

S & F in repairs PCB Senser unit split AC indoor unit of Capacity 1.5 /2 TR suitable for , existing removing old PCB and refix with new PCB of same make & capacity and model in the same position complete all as specified and directed by Engr in Charge.

M&L for cleaning and painting to old steel surfaces of Desert cooler with two coats of synthetic enamel spray paint over one coat of red oxide on external surface & two coats of anti corrosive black paint inside the Body tank & side grills over a coat of Red Oxide primer including scraping/rubbing with wire brush on old surface of Desert cooler complete all as specified and directed by engineer-in-Charge

S&F in replacement Desert Cooler fan motor capacity 1/5 HP, 1400 RPM single phase with fan blade and stand complete all as specified

S & F in repairs Aluminium fan blade (as pe existing size) for fan motor of desert cooler

S&F in repairs capacitor 4 MFD for fan motors of desert coolers.

S&F in replacement PVC insulated and PVC sheathed cable copper conductor 3 core (superior quality) complete all as specified.

S&F in replacement PVC water distributor of 3 out lets with MS nuts & bolts complete all as specified.

S&F in replacement PVC elbow suitable for desert cooler

S&F in replacement PVC pipe 15 mm dia for Desert Cooler Pump complete all as specified

S&F in replacement water lift pump plastic body of 220-240 Volts AC Supply single phase complete all as specified and directed by Engr- in-Charge .

S & F in repairs desert cooler body of size 60x55x65 cm made out of 18 gauge GI sheet & water storage tank of soze 65x55x20 cm deep made out of GI sheet including front grills & three side shutters duly fitted with wood pads 03 Nos & duly spray painted with two coats of synthetic enamel paint over a coat of red oxide primer (inside & outside) complete all as specified &directed by Engr-in-charge.

S & F replacement of wood pads suitable for desert cooler complete all as specified & directed by Engr-in-charge.

National Rewinding Works

M.D. CONSTRUCTION CO.

RAIKA ENTERPRISES