REPAIR/MAINTENANCE OF SUBMERSIBLE PUMP/CENTRIFUGAL PUMP AT DIFFERENT LOCATIONS AT OLD AMRITSAR, GG FORT, VALLA AND SWIMMING POOL ALLIED WORKS UNDER GE AMRITSAR CANTT

Amount

Material and labour for disconnecting of defective burnt elect motor from pump after removing all connection like electrical, earthing etc. by using chain pulley or by other means without causing any damage to existing equipments, transportation to civil work-shop for repair/rewinding, Strip opening elect motor 15 HP, 3 Phase 440 Volts, 1440 RPM, 50 Cycle, removing of defective burnt winding of stator, cleaning of rotor and starter, rewinding the stator of motor with super enameled copper wire of suitable turn and gauge as per original including insulation material for insulation class ‘B’ varnishing and painting outer surface with one coat of synthetic enamel paint with spray gun, reassembling including replacement of ball bearings of same model and make, testing to the entire satisfaction of Engineer-in-Charge and connecting all as per original complete all as specified and directed.

All as per item No. 1 here-in-before but elect motor of capacity 10 HP to 12.5 HP.

All as per item No. 1 here-in-before but elect motor of capacity 5 HP to 7.5 HP.

Material and labour for disconnecting of defective pump set after removing all connections, pipe connections, etc. by using chain pulley or by other maens without causing any damage to existing equipments, transportation to civil work-shop for Strip opening pumping set cap 15 HP, removing of defective ball bearings, shaft and cleaning and reassembling the same after replacemnt of ball bearings and key or lathe work required as per existing pattern and reassambling the same and testing to the entire satisfaction of Engineer-in-Charge and connecting all as per original complete all as specified and directed. Note Shaft and Impeller if requried shall be measured and paid for seperately under supply only items .

All as per item No. 4 here-in-before but elect motor of capacity 10 HP to 12.5 HP.

All as per item No. 4 here-in-before but elect motor of capacity 5 HP to 7.5 HP.

Supply only stainless shaft complete suitable for 15 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only stainless shaft complete suitable for 10 HP to 12.5 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only stainless shaft complete suitable for 5 HP to 7. 5 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only CI impeller complete suitable for 15 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only CI impeller complete suitable for 10 HP to 12.5 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only CI impeller complete suitable for 5 HP to 7. 5 HP pumping set all as per existing pattern complete all as specified and directed.

Material and Labour for lifting defective submersible pumping set of capacity 45 HP to 50 HP complete taking out with the help of chain pulley or by other means by arranging sufficent man power without causing damage to existing equipment, removing flanged column pipe assembly by opening nuts, bolts, etc. including disconnecting of delivery main lines andl electric connection from starter and transporting the motor and pump set to workshop for carrying out repairs as required, reassebling and lowering the same after carrying repairs, connecting coloum pipes with new nuts, bolts, etc. of suitable size as per existing size including lowering existing submersible cable of any size from starter complete and testing to the entire satisfaction of the Engineer-in-charge complete all as specified and directed.

Material and Labour for lifting defective submersible pumping set of capacity 30 HP to 40 HP complete, taking out with help of chain pulley or by other means by arranging sufficent man power without causing damage to existing equipment, removing flanged column pipe assembly by opening nuts, bolts, etc. including disconnecting of delivery main lines and electric connection from starter and transporting the motor and pump set to workshop for carrying out repairs as required, reassebling and lowering the same after carrying repairs, connecting coloum pipes with new nuts, bolts, etc. of suitable size as per existing size including lowering existing submersible cable of any size from starter complete and testing to the entire satisfaction of the Engineer-in-charge complete all as specified and directed.

Material and Labour for lifting defective submersible pumping set of capacity 10 HP to 20 HP complete, taking out with help of chain pulley or by other means by arranging sufficent man power without causing damage to existing equipments, removing flanged column pipe assembly by opening nuts, bolts, etc. including disconnecting of delivery main lines and electric connection from starter and transporting the motor and pump set to workshop for carrying out repairs as required reassebling and lowering the same after carrying repairs, connecting coloum pipes with new nuts, bolts, etc. of suitable size as per existing size including lowering existing submersible cable of any size from starter complete and testing to the entire satisfaction of the Engineer-in-charge complete all as specified and directed.

Material and Labour for lifting defective submersible pumping set of capacity 3 HP to 7.5 HP complete, taking out with help of chain pulley or by other means by arranging sufficent man power without causing damage to existing equipments, removing flanged column pipe assembly by opening nuts, bolts, etc. including disconnecting of delivery main lines and electric connection from starter and transporting the motor and pump set to workshop for carrying out repairs as required, reassebling and lowering the same after carrying repairs, connecting coloum pipes with new nuts, bolts, etc. of suitable size as per existing size including lowering existing submersible cable of any size from starter complete and testing to the entire satisfaction of the Engineer-in-charge complete all as specified and directed. Note for Sr item No - 13 to 16 : Coloum pipe / Submersible cable / impeller / shaft / rotor/ rewinding of electric motor as required shall be measured and paid seperately.

Material and Labour for strip opening of defective 50 HP submersible motor, 3 phase 440 Volt, 50 Cycles, cleaning of shaft and rotor, rewinding the submersible motor with PVC insulated copper conductor winding wire all as same gauge including insulation material for insulation class, and replacemet of bushes/Ball bearings all as per existing pattern, reassembling and testing to the entire satisfaction of the Engineer-in-charge complete all as specified and directed.

Material and Labour for strip opening of defective 40/ 45 HP submersible motor, 3 phase 440 Volt, 50 Cycles, cleaning of shaft and rotor rewinding the submersible motor with PVC insulated copper conductor winding wire all as same gauge including insulation material for insulation class , and replacemet of bushes/Ball bearings all as per existing pattern reassembling and testing to the entire satisfaction of the Engineer-in-charge complete all as specified and directed.

Material and Labour for strip opening of defective 30/ 35 HP submersible motor, 3 phase 440 Volt, 50 Cycles,cleaning of shaft and rotor rewinding the submersible motor with PVC insulated copper conductor winding wire all as same gauge including insulation material for insulation class , and replacemet of bushes/Ball bearings all as per existing pattern reassembling and testing to the entire satisfaction of the Engineer-in-charge complete all as specified and directed.

Material and Labour for strip opening of defective 20/ 25 HP submersible motor, 3 phase 440 Volt, 50 Cycles, cleaning of shaft and rotor, rewinding the submersible motor with PVC insulated copper conductor winding wire all as same gauge including insulation material for insulation class and replacemet of bushes/Ball bearings all as per existing pattern, reassembling and testing to the entire satisfaction of the Engineer-in-charge complete all as specified and directed.

Material and Labour for strip opening of defective 10 HP submersible motor, 3 phase 440 Volt, 50 Cycles, cleaning of shaft and rotor, rewinding the submersible motor with PVC insulated copper conductor winding wire all as same gauge including insulation material for insulation class and replacemet of bushes/Ball bearings all as per existing pattern, reassembling and testing to the entire satisfaction of the Engineer-in-charge complete all as specified and directed.

Material and Labour for strip opening of defective 7.5 HP submersible motor, 3 phase 440 Volt, 50 Cycles, cleaning of shaft and rotor, rewinding the submersible motor with PVC insulated copper conductor winding wire all as same gauge including insulation material for insulation class and replacemet of bushes/Ball bearings all as per existing pattern, reassembling and testing to the entire satisfaction of the Engineer-in-charge complete all as specified and directed.

Material and Labour for strip opening of defective 5 HP submersible motor, 3 phase 440 Volt, 50 Cycles, cleaning of shaft and rotor, rewinding the submersible motor with PVC insulated copper conductor winding wire all as same gauge including insulation material for insulation class and replacemet of bushes/Ball bearings all as per existing pattern reassembling and testing to the entire satisfaction of the Engineer-in-charge complete all as specified and directed.

Material and Labour for strip opening of defective 3 HP submersible motor, 3 phase 440 Volt, 50 Cycles, cleaning of shaft and rotor, rewinding the submersible motor with PVC insulated copper conductor winding wire all as same gauge including insulation material for insulation class and replacemet of bushes/Ball bearings all as per existing pattern reassembling and testing to the entire satisfaction of the Engineer-in-charge complete all as specified and directed.

Material and Labour for strip opening of defective pumping set of capacity 50 HP, removing of defective ball bearings/bush , shaft impller, etc., cleaning and repalcement of ball bearings/bushes, shaft impeller, lathe work required as per existing pattern and reassambling the same and testing to the entire satisfaction of Engineer-in-Charge and connecting all as per original complete all as specified and directed.

Material and Labour for strip opening of defective pumping set of cap 40/45 HP, removing of defective ball bearings/bushes , shaft impller, cleaning and repalcement of ball bearings/bushes, shaft impeller, lathe work required as per existing pattern and reassambling the same and testing to the entire satisfaction of Engineer-in-Charge and connecting all as per original complete all as specified and directed.

Material and Labour for defective Strip opening pumping set cap 30/35 HP, removing of defective ball bearings/bush , shaft impller, cleaning and repalcement of ball bearings/bushes, shaft impeller, lathe work required as per existing pattern and reassambling the same and testing to the entire satisfaction of Engineer-in-Charge and connecting all as per original complete all as specified and directed.

Material and Labour for defective Strip opening pumping set cap 20/25 HP, removing of defective ball bearings/bushes , shaft impller, cleaning and repalcement of ball bearings/bushes, shaft impeller, lathe work required as per existing pattern and reassambling the same and testing to the entire satisfaction of Engineer-in-Charge and connecting all as per original complete all as specified and directed.

Material and Labour for defective Strip opening pumping set cap 10 HP, removing of defective ball bearings/bushes , shaft impller, cleaning and repalcement of ball bearings/bushes, shaft impeller, lathe work required as per existing pattern and reassambling the same and testing to the entire satisfaction of Engineer-in-Charge and connecting all as per original complete all as specified and directed.

Material and Labour for defective Strip opening pumping set cap 7.5 HP, removing of defective ball bearings/bushes , shaft impller, cleaning and repalcement of ball bearings/bushes, shaft impeller, lathe work required as per existing pattern and reassambling the same and testing to the entire satisfaction of Engineer-in-Charge and connecting all as per original complete all as specified and directed.

Material and Labour for defective strip opening pumping set cap 5 HP, removing of defective ball bearings/bushes , shaft impller, cleaning and repalcement of ball bearings/bushes, shaft impeller , lathe work required as per existing pattern and reassambling the same and testing to the entire satisfaction of Engineer-in-Charge and connecting all as per original complete all as specified and directed.

Material and Labour for defective Strip opening pumping set cap 3 HP, removing of defective ball bearings/bushes , shaft impller, cleaning and repalcement of ball bearings/bushes, shaft impeller, lathe work required as per existing pattern and reassambling the same and testing to the entire satisfaction of Engineer-in-Charge and connecting all as per original complete all as specified and directed. Note for item no 25 to 32 :Shaft & Impeller required to be replaced shall be measured and paid for separately as supply only.

Supply only stainless shaft complete suitable for 50 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only stainless shaft complete suitable for 40/45 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only stainless shaft complete suitable for 30/35 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only stainless shaft complete suitable for 20/25 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only stainless shaft complete suitable for 10 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only stainless shaft complete suitable for 7.5 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only stainless shaft complete suitable for 5 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only stainless shaft complete suitable for 3 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only CI impeller complete suitable for 50 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only CI impeller complete suitable for 40/45 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only CI impeller complete suitable for 30/35 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only CI impeller complete suitable for 20/25 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only CI impeller complete suitable for 10 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only CI impeller complete suitable for 7.5 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only CI impeller complete suitable for 5 HP pumping set all as per existing pattern complete all as specified and directed.

Supply only CI impeller complete suitable for 3 HP pumping set all as per existing pattern complete all as specified and directed.

Supply, fixing, testing and commissioning Submersible pump with motor complete set of 60 HP capable of delivering below mentioned dischargeof specified head water cooled copper rotor motor sync. Speed 2880 rpm at rated 415 volts with wide voltage variation of +5% and - 15% , 3 Phase, 50 Hz. A.C. power supply with flow pump suitable for 300mm/350mm dia deep borewell, 2300 LPM & 70 meter water Head and conforming to latest IS including taking out the existing pump set complete and depositing the same to store yard of AGE EM complete all as specified and directed..

Supply, fixing, testing and commissioning Submersible pump with motor complete set of 45 HP capable of delivering below mentioned discharge at specified head water cooled copper rotor motor sync. Speed 2880 rpm at rated 415 volts with wide voltage variation of +5% and - 15%, Phase Phase, 50 Hz. A.C. power supply with flow pump suitable for 300mm/350mm dia deep borewell, 100 Cum/Hr & 80 meter water Head 10 stage conforming to latest IS . Bore hole with normal clean drinking water including taking out the existing pump set complete and depositing the same to store yard of AGE EM complete all as specified and directed.

Supply, fixing, testing and commissioning of Submersible pump with motor complete set of 35 HP capable of delivering below mentioned dischargeof specified head water cooled copper rotor motor sync. Speed 2880 rpm at rated 415 volts with wide voltage variation of +5% and - 15%, 3 Phase, 50 Hz. A.C. power supply flow pump suitable for 300mm/ 350mm dia deep borewell, 2400 LPM & 70 meter water Head 10 STAGE conforming to latest IS . Bore hole with normal clean drinking wate including taking out the existing pump set complete and depositing the same to store yard of AGE EM complete all as specified and directed.

Supply, fixing, testing and commissioning Submersible pump. with motor complete set of 15 HP capable of delivering below mentioned dischargeof specified head water cooled copper rotor motor sync. Speed 2830 rpm at rated 415 volts with wide voltage variation of +5% and - 15%, 3 Phase, 50 Hz. A.C. power supply flow pump suitable for 300mm/ 350mm dia deep borewell,5000 GPH & 75 TO 100 meter water Head conforming to latest IS including taking out the existing pump set complete and depositing the same to store yard of AGE EM complete all as specified and directed. Note for item No 49 TO 52 above : (a)The discharge outlet of the pumset should be as per manufacturers specifications. (b) Manufacturer test certificate and technical data sheet / performance report shall be submitted by the contractor. (c) The cap of motor, discharge & head of pump as mentioned is minimum if the same is not available . The contractor should supply the same on higher side, the amount of the same shall be deemed to be included in the quoted rate . No extra payment is admissible to the contractor on the account.

Supply and fixing in replacement ,PVC insulated 3 Core industrial grade flat submersible cable copper conductor 1100 V size 16 Sqmm complete all as specified and directed.

Supply and fixing in replacement PVC insulated 3 Core industrial grade flat submersible cable copper conductor 1100 V size 10 Sqmm complete all as specified and directed.

Supply and fixing in replacement, MS flanged pipe of size 150 mm dia heavy duty 'C' class with necessary MS bolts, nuts and washers, packing material, rubber gaskets, pressure gauge for lowering etc. as per IS: 1239 Part-I 2004 complete all as specified and as directed. Note: Cost of lifting the pump, removing of old pipes, fixing the new pipes and lowering the pump if required is included in the quoted rate.

Supply and fixing in replacement, MS flanged pipe of size 100 mm dia heavy duty 'C' class with necessary MS bolts, nuts and washers, packing material, rubber gaskets, pressure gauge etc, for lowering as per IS: 1239 Part-I 2004 complete all as specified and as directed. Note: Cost of lifting the pump ,removing old pipes, fixing the new pipes and lowering the pump if required is included in the quoted rate.

Supply, fixing, testing and commissioning centrifugal pumping set electric driven 3 phase pump. with motor complete set of 12.5 HP capable of delivering below mentioned discharge of specified head water cooled copper rotor motor sync. high Speed 2880 rpm at rated 415 volts with wide voltage variation of +5% and - 15%, 3 Phase, 50 Hz. A.C. power supply , 500 -600 LPM & 10 meter water Head conforming to latest IS including taking out the existing pump set complete and depositing the same to store yard of AGE EM complete all as specified and directed.

Supply and fixing, testing and commissioning of suction sweeper centrifugal supply set control with electric motor 5 HP cap , 3 phase 415 volts discharge 15 to 30 LPH at 16.5 meter head width 80mmx80 mm suction and delivery completed trolly mounted on wheels as per OEM flexible pipe 50 mm dia 30 metre long including necessary GI fittings same as per reducer 80x50 mm and clamp including taking out the existing pump set complete and depositing the same to store yard of AGE EM complete all as specified and directed. Note for 57 & 58 : (A) The capacity of motor, discharge & head of pump as mentioned is minimum if the same is not available . The contractor should supply the same on higher side, the cost of the same shall be deemed to be included in the quoted rate . No extra payment is admissible to the contractor on the account.

Supply and fixing in replacement fiber glass sand filter commerical sand filter tank 1400 mm dia made out of MS/FRP complete with nozzles butter fly valves air vrelease valves and six position multi port valve plant water flow not less than 32 CUM/HR complete with accessories internal fitting and filter media sand of all sizes as per OEM recommendation testing on full load complete all as specified and directed. NOTE : Any item if not mentioned in the description to make the filter funtional satishfactorily, the same shall be deemed to be included in the rate quoted by the contractor . No extra payment shall be admissible to the contractor on the account.

Supply and fixing in replacement power contactor 3 pole power contactor ML 5, AC-3 rating, 40 Amp, with auxilary 240 V contact including making electrical connections and removal old complete all as specified and directed.

Supply and fixing in replacement over load relay having relay range 25 to 35 Amps built in single phase protection facility, manual & auto reset mode, front access to START and STOP/RESET buttons including making electrical connections and removal old complete all as specified and directed.

Supply and fixing in replacement over load relay having relay range exceeding 25 not exceeding 35 Amps built in single phase protection facility, manual & auto reset mode, front access to START and STOP/RESET buttons including making electrical connections and removal old complete all as specified and directed.

Supply and fixing in replacement electronics timer with time delay period of 3 to30 second for 415 volt, 50 Hz, AC supply suitable for star-delta starter for any capacity pump-motor including making electrical connections and removal old complete all as specified and directed.

Supply and fixing in repair MCCB triple pole and neutral (4 pole) 200-250 Amp, 415 volts, 50 Hz, having thermal setting range 70% to 100% and fixed magnetic setting and breaking capacity 36 kA including making incoming/outgoing connections and removal old complete all as specified and directed.

All as per item No. 64 above but of 160 Amps 25 kA.

All as per item No. 64 above but of 100 Amps 25 kA.

Supply and fixing in replacement Submersible Pump Controller in sheet encloures in replacement fully Automatic Star-Delta Starter, with short circuit protection with inbuilt metering & MCB, 3 Phase, 415 Volt, AC-3 duty, 50 Hz, Motor Output Capacity upto 20 HPand relay range 13.21 Amps and making incoming & outgoing electric connection and removal old complete all as specified and directed.

All as per ser item No.67 above but of motor outpur capacity 35 HP (20-32 AMP) and relay range 22-32 Amps.

All as per ser item No.67 above but of motor outpur capacity 40 HP (26-60 AMP) and relay range 28-40 Amps.

All as per ser item No. 67 above but of motor outpur capacity 50 HP/37.5 KW and relay range 45-75 Amps.

Supply and fixing in repair Direct-on-Line (DOL) starter in sheet encloures, 3 Phase, 415 Volt, AC-3 duty, 50 Hz, Motor Output Capacity upto 5 HP /3.5 KW and relay range 9-14 Amps and making incoming & outgoing electric connection and removal old complete all as specified and directed.

Material and labour for repair to Altoch dosing unit by dismantling of pump, motor and other connecting components/accessories, replacement of spare parts as required and carrying out necessary repair works, making the machine functional, reassembling, fixing in position and testing complete all as specified and directed. NOTE: Spare parts required to be replaced for repair of dozing pump shall be measured and paid under Sl item No 73 to 81 here-in-after as supply only.

Supply only gear motor complete set with working voltage 230 Volts, 50 Hz complete all as specified and directed. Make: Declibac Technologies, Rmco, Technomac.

Supply only rotor assembly with bearing brackets and tolerance rings complete all as specified and directed. Make: Declibac Technologies, Rmco, Technomac.

Supply only field/armature coil 250 Volts, 50 Hz complete all as specified and directed. Make: Declibac Technologies, Rmco, Technomac.

Supply only roller assembly complete all as specified and directed. Make: Declibac Technologies, Rmco, Technomac.

Supply only 7 pump tube complete all as specified and directed. Make: Declibac Technologies, Rmco, Technomac.

Supply only injection check valve 3/8" complete all as specified and directed. Make: Declibac Technologies, Rmco, Technomac.

Supply only 3/8" white suction/discharge tubing complete all as specified and directed. Make: Declibac Technologies, Rmco, Technomac.

Supply only check value duckbill only (Pkt of 5) complete all as specified and directed. Make: Declibac Technologies, Rmco, Technomac.

Supply only connecting nut 3/8"complete all as specified and directed. Make: Declibac Technologies, Rmco, Technomac.

Material and labour for development of bore well with high capacity air compresser of suitable sizefor running duration not less than 4 hours till the water becomes sand and silt free including removal of liquid mud, sand, silt etc. up to a distance of 50 metre and deposited where directed, complete all as specified & directed. NOTE: (a) Air compressor, fuel, manpower, any other equipment of suitable capacity for the development of tube well shall be arranged by the contractor under his own arrangements and nothing extra shall be payable to the contractor on this account. (b) The discharge shall be measured by providing orifice system of 'V' notch fixed to steel tanks of adequate capacity. (c) A proper record and log sheet for running of compressor shall be prepared and signed by the contractor & Engineer-in-Charge, countersigned by GE and shall form part of final bill.

Material and labour for earthing complete with galvanized steel earth plate electrode 60cmX60cmX6.0 mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of plate not less than 1.5m below normal ground level, earth plate connected to GI strip earth lead of size 32 x 6 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 of MES SSR part I connected to earth test point all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 meter long for earth wire including PCC (1:2:4) pit with precast RCC (1:2:4) type B -1 cover, 40mm thick reinforced with 6mm dia MS bars @ 100 mm both ways with lifting hooks made out of 6mm dia MS bars, watering arrangement with funnel, wire, common salt, charcoal filling, necessary excavation and earth work in any type of soil complete all as specified and directed.

Supply and fixing in replacement 150 mm dia NRV, ISI marked confirming to IS-14846, flanged and drilled, including jointing material such as nuts, bolts, washers and rubber sheet etc. and removal old complete all as specified and directed.

Supply and fixing in replacement 150mm dia sluice valve PN 1:0, ISI marked confirming to IS-14846, flanged and drilled, Steel spindle and iron wheel including jointing material such as nuts, bolts, washers and rubber sheet etc. and removal old complete all as specified and directed.

Material and Labour for checking, inspecting and maintaining for water leakage of centrifugal pump set, sluice valves any size, electrical faults, etc., in different various locations as directed including replacement of required size of gland packings and making leak proof, electrical connections, etc., complete all as specified and directed. NOTE: (a) Cost of gland packing of required size shall be deemed to be included in the quoted rate. (b) One supervisor will report to the JE in Charge on daily along with complaint register, complaint slip in duplicate which shall also be arranged by the contractor without any extra cost for recording/monitoring of water supply complaints.

Material and Labour for collecting the treated water samples in a sterilized bottles to be provided by the contractor as per requirement by the Govt laborites , as and when directed by the deptt. and transporting the samples upto Govt recognized laboratory at Amritsar for carrying out the test as per IS-10500 : 2012 for drinking water and submitting report to the entire satishfaction of Engr-in-Charge

M/s Shiv Electrical & Mechanical Works (BID ID -3349846)

SUN CHEMICALS (BID ID -3349431)

HARPAL ENGINEERS AND BUILDERS (BID ID -3358578)

M/S RASHPAL CONSTRUCTION CO (BID ID -3358539)

Harai Sharan Govt Contractor (BID ID -3358035)