COMP MAINT OF DG SETS, REPLACEMENT OF FILTERS, AVR, CANOPIES, REWINDING OF ALTERNATOR, MAINT OF AMF PANEL, LT PANEL, DEFECTIVE MCCB, LT CABLES ALONGWITH CERTAIN ROAD FURNITURE IN EXPL/NON EXPL AREA NAD, TUNIR, ABHIMANYU AND AMN JETTY AT NS KARANJA

Amount

Material and labour for engine complete overhauling of DG set capacity 15 KVA to 30 KVA of Kirloskar/ Crompton Greaves makes by opening the top cover complete including dismantling the engine head, cylinder liner and piston assembly, crank shaft assembly, radiator fan belt and radiator fan, gear assembly complete removing of engine side for repair/ replacement of parts i.e. gasket, washer, 'O' ring all types etc including grinding polishing of crank shaft , head repairing and overhauling valve seat cutting and replacing, valve tapping, head assemble and testing of DG set after necessary repair with an authorised dealer, fix at site, reassembling of DG set and testing on full load upto entire satisfaction of Engineer-in-Charge complete all as specified and directed. Note : Spare parts will be measured and paid separately under relevant items.

Supply only piston assembly

Supply only piston ring set

Supply only full engine gasket

Supply only main bearing set

Supply only main cylinder liner

Supply only main cylinder head copper sleeves

Supply only lock nut

Supply only big end bearing

Supply only timing belt

Supply only benjo bolt

Supply only timing belt tension adjuster

Supply only inlet valve

Supply only exhaust valve

Supply only head gasket

Supply only oil pump assembly

Supply only thrust washer

Supply only crank case gasket

Supply only head nozzle plug set

Material and labour for engine complete overhauling of DG set capacity 62.50 KVA to 110 KVA of Kirloskar/ Crompton Greaves makes by opening the top cover complete including dismantling the engine head, cylinder liner and piston assembly, crank shaft assembly, radiator fan belt and radiator fan, gear assembly complete removing of engine side for repair/ replacement of parts i.e. gasket, washer, 'O' ring all types etc including grinding polishing of crank shaft , head repairing and overhauling valve seat cutting and replacing, valve tapping, head assemble and testing of DG set after necessary repair with an authorised dealer, fix at site, reassembling of DG set and testing on full load upto entire satisfaction of Engineer-in-Charge complete all as specified and directed. Note : Spare parts will be measured and paid separately under relevant items.

Supply only piston assembly

Supply only piston ring set

Supply only full engine gasket

Supply only main bearing set

Supply only main cylinder liner

Supply only main cylinder head copper sleeves

Supply only lock nut

Supply only big end bearing

Supply only timing belt

Supply only benjo bolt

Supply only timing belt tension adjuster

Supply only inlet valve

Supply only exhaust valve

Supply only head gasket

Supply only oil pump assembly

Supply only thrust washer

Supply only crank case gasket

Supply only head nozzle plug set

Material and labour for engine complete overhauling of DG set capacity 125 KVA to 200 KVA of Kirloskar/ Crompton Greaves makes by opening the top cover complete including dismantling the engine head, cylinder liner and piston assembly, crank shaft assembly, radiator fan belt and radiator fan, gear assembly complete removing of engine side for repair/ replacement of parts i.e. gasket, washer, 'O' ring all types etc including grinding polishing of crank shaft , head repairing and overhauling valve seat cutting and replacing, valve tapping, head assemble and testing of DG set after necessary repair with an authorised dealer, fix at site, reassembling of DG set and testing on full load upto entire satisfaction of Engineer-in-Charge complete all as specified and directed. Note : Spare parts will be measured and paid separately under relevant items.

Supply only piston assembly

Supply only piston ring set

Supply only full engine gasket

Supply only main bearing set

Supply only main cylinder liner

Supply only main cylinder head copper sleeves

Supply only lock nut

Supply only big end bearing

Supply only timing belt

Supply only benjo bolt

Supply only timing belt tension adjuster

Supply only inlet valve

Supply only exhaust valve

Supply only head gasket

Supply only oil pump assembly

Supply only thrust washer

Supply only crank case gasket

Supply only head nozzle plug set

Material and labour for engine complete overhauling of DG set capacity 250 KVA to 400 KVA of Kirloskar/ Crompton Greaves makes by opening the top cover complete including dismantling the engine head, cylinder liner and piston assembly, crank shaft assembly, radiator fan belt and radiator fan, gear assembly complete removing of engine side for repair/ replacement of parts i.e. gasket, washer, 'O' ring all types etc including grinding polishing of crank shaft , head repairing and overhauling valve seat cutting and replacing, valve tapping, head assemble and testing of DG set after necessary repair with an authorised dealer, fix at site, reassembling of DG set and testing on full load upto entire satisfaction of Engineer-in-Charge complete all as specified and directed. Note : Spare parts will be measured and paid separately under relevant items.

Supply only piston assembly

Supply only piston ring set

Supply only full engine gasket

Supply only main bearing set

Supply only main cylinder liner

Supply only main cylinder head copper sleeves

Supply only lock nut

Supply only big end bearing

Supply only timing belt

Supply only benjo bolt

Supply only timing belt tension adjuster

Supply only inlet valve

Supply only exhaust valve

Supply only head gasket

Supply only oil pump assembly

Supply only thrust washer

Supply only crank case gasket

Supply only head nozzle plug set

Material and labour for engine complete overhauling of DG set capacity 500 KVA to 750 KVA of Kirloskar/ Crompton Greaves makes by opening the top cover complete including dismantling the engine head, cylinder liner and piston assembly, crank shaft assembly, radiator fan belt and radiator fan, gear assembly complete removing of engine side for repair/ replacement of parts i.e. gasket, washer, 'O' ring all types etc including grinding polishing of crank shaft , head repairing and overhauling valve seat cutting and replacing, valve tapping, head assemble and testing of DG set after necessary repair with an authorised dealer, fix at site, reassembling of DG set and testing on full load upto entire satisfaction of Engineer-in-Charge complete all as specified and directed. Note : Spare parts will be measured and paid separately under relevant items.

Supply only piston assembly

Supply only piston ring set

Supply only full engine gasket

Supply only main bearing set

Supply only main cylinder liner

Supply only main cylinder head copper sleeves

Supply only lock nut

Supply only big end bearing

Supply only timing belt

Supply only benjo bolt

Supply only timing belt tension adjuster

Supply only inlet valve

Supply only exhaust valve

Supply only head gasket

Supply only oil pump assembly

Supply only thrust washer

Supply only crank case gasket

Supply only head nozzle plug set

Supply and Fix MCCB of 160 A, adjustable type , 4 pole 415 volt 16 kA breaking cap. With adjustable over load, short circuit, ground fault (4 pole) & fixed instantaneous neutral protection(4 pole), conforming to IS/IEC-60947-2 with spreader terminal kit including taking down unserviceable MCCB, complete all as specified and directed by Engr-in-Charge.

Supply and Fix MCCB of 250 A, adjustable type , 4 pole 415 volt 35 kA breaking cap. With adjustable over load, short circuit, ground fault (4 pole) & fixed instantaneous neutral protection(4 pole), conforming to IS/IEC-60947-2 with spreader terminal kit including taking down unserviceable MCCB, complete all as specified and directed by Engr-in-Charge.

Supply and Fix MCCB of 400 A, adjustable type, 4 pole 415 volt 50 kA breaking cap. With adjustable over load, short circuit, ground fault (4 pole) & fixed instantaneous neutral protection(4 pole), conforming to IS/IEC-60947-2 with spreader terminal kit including taking down unserviceable MCCB, complete all as specified and directed by Engr-in-Charge.

Supply and Fix in repair of Contactor- 3/4 Pole,150 Amps/ 140 Amps for up to 62.5 KVA DG Set AMF panel with replacement of lugs and checking of all connections etc including taking down unserviceable contactor, complete all as specified and directed by Engr-in-Charge.

Supply and Fix in repair of Contactor- 4 Pole, 225 Amp/ 200 Amp for 62.5 to 150 KVA DG set AMF panel with replacement of lugs and checking of all connections etc taking down unserviceable contactor, complete all as specified and directed by Engr-in-Charge.

Supply and Fix in repair of Contactor of 4 Pole, 250 Amps for AMF PANEL of DG Set with replacement of cable lugs and checking of all connections etc taking down unserviceable contactor, complete all as specified and directed by Engr-in-Charge.

Supply and Fix in repair of Contactor of 4 Pole, 320 Amps for AMF PANEL of DG Set with replacement of cable lugs and checking of all connections etc taking down unserviceable contactor, complete all as specified and directed by Engr-in-Charge.

Supply and Fix in repair of Contactor of 4 Pole, 400 Amps for AMF PANEL of DG Set with replacement of cable lugs and checking of all connections etc taking down unserviceable contactor, complete all as specified and directed by Engr-in-Charge.

Supply and Fix in repair of Self Engine Stop Relay Device for 63 KVA to 180 KVA DG set AMF panel, complete all as specified and directed by Engr-in-Charge.

Supply and Fix in repair of Self Engine Stop Relay Device for 200 KVA to 315 KVA DG set AMF panel, complete all as specified and directed by Engr-in-Charge.

Supply and Fix in repair of Self Engine Stop Relay Device for 400 KVA to 625 KVA DG set AMF panel, complete all as specified and directed by Engr-in-Charge.

Maintenance and servicing to DG set including cleaning of DG set canopy, radiator and other parts with alkaline based chemical (water based) including replacement of defective and worn out minor filters gaskets, V- belts, Engine oil, rubber hoses, worm drive clamps, nuts, bolts and cleaning of alternator with vacuum cleaner and attending faults of AMF panels etc, tappet settings if required and greasing/oiling of bearings of engine, alternator and other moving parts checking of batteries, applying petroleum jelly to battery terminals, adding distilled water checking the oil, coolant levels of capacity 625-750 KVA DG set installed, complete all as specified and directed by Engr-in-Charge. Notes:- (i) Spares required for maintenance will be measured and paid separately under relevant items. (ii) Servicing to be carried out as per manufacturer’s specifications/ instructions. (iii) Work shall be carried out at site at different location.

TECHO CABLE

PRIMING PUMP

O RING

SUPER BYPASS FILTER WITH O RING

RADIATOR HOSE SET

CLAMP SET

AIR CLEANER HUMP HOSE

AIR CLEANER HUMP HOSE CLAMP

TURBO HUMP HOSE

TURBO HUMP HOSE CLAMP

VENT HOSE PIPE

Lub oil filter

FUEL PRE FILTER

FUEL MICRO FILTER

AIR FILTER PRIME

AIR FILTER SECOND

OIL TEMP. GAUGE

WATER TEMP. GAUGE

OIL PRESSURE GAUGE

Fan Belt

Uniball Joint

Thermostat

Hose diesel ( 7 Ft. )

Oil filter head gasket

RPM meter

Maintenance and servicing to DG set including cleaning of DG set canopy, radiator and other parts with alkaline based chemical (water based) including replacement of defective and worn out minor filters gaskets, V- belts, Engine oil, rubber hoses, worm drive clamps, nuts, bolts and cleaning of alternator with vacuum cleaner and attending faults of AMF panels etc, tappet settings if required and greasing/oiling of bearings of engine , alternator and other moving parts checking of batteries, applying petroleum jelly to battery terminals, adding distilled water checking the oil, coolant levels of capacity 500 KVA DG set installed, complete all as specified and directed by Engr-in-Charge. Notes:- (i) Spares required for maintenance will be measured and paid separately under relevant items. (ii) Servicing to be carried out as per manufacturer’s specifications/ instructions. (iii) Work shall be carried out at site at different location.

TECHO CABLE

PRIMING PUMP

O RING

SUPER BYPASS FILTER WITH O RING

RADIATOR HOSE SET

CLAMP SET

AIR CLEANER HUMP HOSE

AIR CLEANER HUMP HOSE CLAMP

TURBO HUMP HOSE

TURBO HUMP HOSE CLAMP

VENT HOSE PIPE

Lub oil filter

FUEL PRE FILTER

FUEL MICRO FILTER

AIR FILTER PRIME

AIR FILTER SECOND

OIL TEMP. GAUGE

WATER TEMP. GAUGE

OIL PRESSURE GAUGE

Fan Belt

Uniball Joint

Thermostat

Hose diesel ( 7 Ft. )

Oil filter head gasket

RPM meter

Maintenance and servicing to DG set including cleaning of DG set canopy, radiator and other parts with alkaline based chemical (water based) including replacement of defective and worn out minor filters gaskets, V- belts, Engine oil, rubber hoses, worm drive clamps, nuts, bolts and cleaning of alternator with vacuum cleaner and attending faults of AMF panels etc, tappet settings if required and greasing/oiling of bearings of engine , alternator and other moving parts checking of batteries, applying petroleum jelly to battery terminals, adding distilled water checking the oil, coolant levels of capacity 400 KVA DG set installed, complete all as specified and directed by Engr-in-Charge. Notes:- (i) Spares required for maintenance will be measured and paid separately under relevant items. (ii) Servicing to be carried out as per manufacturer’s specifications/ instructions. (iii) Work shall be carried out at site at different location.

TECHO CABLE

PRIMING PUMP

O RING

SUPER BYPASS FILTER WITH O RING

RADIATOR HOSE SET

CLAMP SET

AIR CLEANER HUMP HOSE

AIR CLEANER HUMP HOSE CLAMP

TURBO HUMP HOSE

TURBO HUMP HOSE CLAMP

VENT HOSE PIPE

Lub oil filter

FUEL PRE FILTER

FUEL MICRO FILTER

AIR FILTER PRIME

AIR FILTER SECOND

OIL TEMP. GAUGE

WATER TEMP. GAUGE

OIL PRESSURE GAUGE

Fan Belt

Uniball Joint

Thermostat

Hose diesel ( 7 Ft. )

Oil filter head gasket

RPM meter

Maintenance and servicing to DG set including cleaning of DG set canopy, radiator and other parts with alkaline based chemical (water based) including replacement of defective and worn out minor filters gaskets, V- belts, Engine oil, rubber hoses, worm drive clamps, nuts, bolts and cleaning of alternator with vacuum cleaner and attending faults of AMF panels etc, tappet settings if required and greasing/oiling of bearings of engine , alternator and other moving parts checking of batteries, applying petroleum jelly to battery terminals, adding distilled water checking the oil, coolant levels of capacity 200-250 KVA DG set installed, complete all as specified and directed by Engr-in-Charge. Notes:- (i) Spares required for maintenance will be measured and paid separately under relevant items. (ii) Servicing to be carried out as per manufacturer’s specifications/ instructions. (iii) Work shall be carried out at site at different location.

TECHO CABLE

PRIMING PUMP

O RING

SUPER BYPASS FILTER WITH O RING

RADIATOR HOSE SET

CLAMP SET

AIR CLEANER HUMP HOSE

AIR CLEANER HUMP HOSE CLAMP

TURBO HUMP HOSE

TURBO HUMP HOSE CLAMP

VENT HOSE PIPE

Lub oil filter

FUEL PRE FILTER

FUEL MICRO FILTER

AIR FILTER PRIME

AIR FILTER SECOND

OIL TEMP. GAUGE

WATER TEMP. GAUGE

OIL PRESSURE GAUGE

Fan Belt

Uniball Joint

Thermostat

Hose diesel ( 7 Ft. )

Oil filter head gasket

RPM meter

Maintenance and servicing to DG set including cleaning of DG set canopy, radiator and other parts with alkaline based chemical (water based) including replacement of defective and worn out minor filters gaskets, V- belts, Engine oil, rubber hoses, worm drive clamps, nuts, bolts and cleaning of alternator with vacuum cleaner and attending faults of AMF panels etc, tappet settings if required and greasing/oiling of bearings of engine , alternator and other moving parts checking of batteries, applying petroleum jelly to battery terminals, adding distilled water checking the oil, coolant levels of capacity 100-125 KVA DG set installed, complete all as specified and directed by Engr-in-Charge. Notes:- (i) Spares required for maintenance will be measured and paid separately under relevant items. (ii) Servicing to be carried out as per manufacturer’s specifications/ instructions. (iii) Work shall be carried out at site at different location.

TECHO CABLE

PRIMING PUMP

O RING

SUPER BYPASS FILTER WITH O RING

RADIATOR HOSE SET

CLAMP SET

AIR CLEANER HUMP HOSE

AIR CLEANER HUMP HOSE CLAMP

TURBO HUMP HOSE

TURBO HUMP HOSE CLAMP

VENT HOSE PIPE

Lub oil filter

FUEL PRE FILTER

FUEL MICRO FILTER

AIR FILTER PRIME

AIR FILTER SECOND

OIL TEMP. GAUGE

WATER TEMP. GAUGE

OIL PRESSURE GAUGE

Fan Belt

Uniball Joint

Thermostat

Hose diesel ( 7 Ft. )

Oil filter head gasket

RPM meter

Maintenance and servicing to DG set including cleaning of DG set canopy, radiator and other parts with alkaline based chemical (water based) including replacement of defective and worn out minor filters gaskets, V- belts, Engine oil, rubber hoses, worm drive clamps, nuts, bolts and cleaning of alternator with vacuum cleaner and attending faults of AMF panels etc, tappet settings if required and greasing/oiling of bearings of engine , alternator and other moving parts checking of batteries, applying petroleum jelly to battery terminals, adding distilled water checking the oil, coolant levels of capacity 62.5 KVA DG set installed , complete all as specified and directed by Engr-in-Charge. Notes:- (i) Spares required for maintenance will be measured and paid separately under relevant items. (ii) Servicing to be carried out as per manufacturer’s specifications/ instructions. (iii) Work shall be carried out at site at different location.

TECHO CABLE

PRIMING PUMP

O RING

SUPER BYPASS FILTER WITH O RING

RADIATOR HOSE SET

CLAMP SET

AIR CLEANER HUMP HOSE

AIR CLEANER HUMP HOSE CLAMP

TURBO HUMP HOSE

TURBO HUMP HOSE CLAMP

VENT HOSE PIPE

Lub oil filter

FUEL PRE FILTER

FUEL MICRO FILTER

AIR FILTER PRIME

AIR FILTER SECOND

OIL TEMP. GAUGE

WATER TEMP. GAUGE

OIL PRESSURE GAUGE

Fan Belt

Uniball Joint

Thermostat

Hose diesel ( 7 Ft. )

Oil filter head gasket

RPM meter

Maintenance and servicing to DG set including cleaning of DG set canopy, radiator and other parts with alkaline based chemical (water based) including replacement of defective and worn out minor filters gaskets, V- belts, Engine oil, rubber hoses, worm drive clamps, nuts, bolts and cleaning of alternator with vacuum cleaner and attending faults of AMF panels etc, tappet settings if required and greasing/oiling of bearings of engine , alternator and other moving parts checking of batteries, applying petroleum jelly to battery terminals, adding distilled water checking the oil, coolant levels of capacity 15-30 KVA DG set installed , complete all as specified and directed by Engr-in-Charge. Notes:- (i) Spares required for maintenance will be measured and paid separately under relevant items. (ii) Servicing to be carried out as per manufacturer’s specifications/ instructions. (iii) Work shall be carried out at site at different location.

TECHO CABLE

PRIMING PUMP

O RING

SUPER BYPASS FILTER WITH O RING

RADIATOR HOSE SET

CLAMP SET

AIR CLEANER HUMP HOSE

AIR CLEANER HUMP HOSE CLAMP

TURBO HUMP HOSE

TURBO HUMP HOSE CLAMP

VENT HOSE PIPE

Lub oil filter

FUEL PRE FILTER

FUEL MICRO FILTER

AIR FILTER PRIME

AIR FILTER SECOND

OIL TEMP. GAUGE

WATER TEMP. GAUGE

OIL PRESSURE GAUGE

Fan Belt

Uniball Joint

Thermostat

Hose diesel ( 7 Ft. )

Oil filter head gasket

RPM meter

Material and Labour for attending emergency complaint on call basis within 8 hrs of complaint lodging with the contractor for 15 KVA to 625 KVA DG sets and repairs to DG sets including carrying out minor repairs etc as required to make the system in order/ functional , complete all as specified and directed by Engr-in-Charge. Note:- Rate inclusive of minor nut bolt, cleaning cloth, grease etc.

Material and labour for disconnecting all electrical connections from DG set alternator of any capacity from base plate by opening nuts & bolts keeping aside the alternator for inspection and taking out to work shop for rewinding including testing and commissioning , complete all as specified and directed by Engr-in-Charge.

Material and Labour for rewinding of alternator field coil with super enamelled copper winding wire of class 'F' insulation as per existing size and gauge including heating, varnishing and testing for capacity 10 KVA DG set to 20 KVA DG set, complete all as specified and directed by Engr-in-Charge.

-Ditto- all as per serial item No.26.00 here-in-before but for capacity 30 KVA DG set to 62.5 KVA DG set.

-Ditto- all as per serial item No.26.00 here-in-before but for capacity 100 KVA DG set to 125 KVA DG set.

-Ditto- all as per serial item No.26.00 here-in-before but for capacity 150 KVA DG set to 200 KVA DG set.

-Ditto- all as per serial item No.26.00 here-in-before but for capacity 250 KVA DG set to 380 KVA DG set.

-Ditto- all as per serial item No.26.00 here-in-before but for capacity 400 KVA DG set to 500 KVA DG set.

-Ditto- all as per serial item No.26.00 here-in-before but for capacity 625 KVA DG set to 750 KVA DG set.

Material and labour for water temperature gauge including sensor and cable complete as per sample including removal of existing unserviceable one, complete all as specified and directed by Engr-in-Charge.

Material and labour for dismantling the radiator and taking to work shop for overhauling & cleaning, de-scaling with alkaline based chemical, removal of leakage including soldering and welding, brazing as required and renewal of gaskets, nuts, bolts, mounting pads, hoses, clips, etc and refixing its original position for capacity of 15 KVA to 30 KVA DG set, complete all as specified and directed by Engr-in-Charge.

-Ditto- all as per serial item No.34.00 here-in-before but for capacity 50 KVA DG set to 62.5 KVA DG set.

-Ditto- all as per serial item No.34.00 here-in-before but for capacity 100 KVA DG set to 125 KVA DG set.

-Ditto- all as per serial item No.34.00 here-in-before but for capacity 150 KVA DG set to 200 KVA DG set.

-Ditto- all as per serial item No.34.00 here-in-before but for capacity 250 KVA DG set to 380 KVA DG set.

-Ditto- all as per serial item No.34.00 here-in-before but for capacity 400 KVA DG set to 500 KVA DG set.

-Ditto- all as per serial item No.34.00 here-in-before but for capacity 625 KVA DG set to 750 KVA DG set.

Material and labour for repair and calibration of FIP and injectors from repairs to make the FIP functional as per standard calibration procedure and norms including replacement of minor spares, gasket etc for smooth functioning of FIP and refixing its original position including testing at site for capacity 10 KVA to 20.00 KVA DG set , complete all as specified and directed by Engr-in-Charge.

-Ditto- all as per serial item No.41.00 here-in-before but for capacity 30 KVA DG set to 50 KVA DG set.

-Ditto- all as per serial item No. 41.00 here-in-before but for capacity 62.5 KVA DG set to 125 KVA DG set.

-Ditto- all as per serial item No.41.00 here-in-before but for capacity 150 KVA DG set to 200 KVA DG set.

-Ditto- all as per serial item No.41.00 here-in-before but for capacity 250 KVA DG set to 380 KVA DG set.

-Ditto- all as per serial item No.41.00 here-in-before but for capacity 400 KVA DG set to 625 KVA DG set.

Supply and Fix in repair of Contactor- 3 Pole, 225 Amp/ 200 Amp for 62.5 to 150 KVA DG set AMF panel with replacement of lugs and checking of all connections etc taking down unserviceable contactor, complete all as specified and directed by Engr-in-Charge..

Supply and Fix in repair of Contactor of 3 Pole, 250 Amps for AMF PANEL of DG Set with replacement of cable lugs and checking of all connections etc taking down unserviceable contactor, complete all as specified and directed by Engr-in-Charge.

Supply and Fix in repair of Contactor of 3 Pole, 400 Amps for AMF PANEL of DG Set with replacement of cable lugs and checking of all connections etc taking down unserviceable contactor, complete all as specified and directed by Engr-in-Charge.

Material and labour for repair/ overhauling of self starting system of DG set including replacement of carbon brushes, bearings, bushes, rewinding of armature and field coil etc and varnishing of capacity 24 volts with necessary connections including testing and commissioning, complete all as specified and directed by Engr-in-Charge.

Material and labour for repair/ overhauling of self starting system of DG set including replacement of carbon brushes, bearings, bushes, rewinding of armature and field coil etc and varnishing of capacity 12 volts with necessary connections including testing and commissioning, complete all as specified and directed by Engr-in-Charge.

Material and Labour for fabrication/Jointing/welding work to repair DG set door of Capacity 15-200 KVA including repairing of hinges, doors, clamp, handle, angle iron, nut bolts & replacement lock with existing type and size, complete all as specified and directed by Engr-in-Charge.

Material and Labour for fabrication/Jointing/welding work to repair DG set door of Capacity 200-625 KVA including repairing of hinges, doors, clamp, handle, angle iron, nut bolts & replacement lock with existing type and size, complete all as specified and directed by Engr-in-Charge.

Material and Labour for spray painting to DG set canopy of capacity 15-200 KVA by cleaning the existing old paint with the help of mechanical tools such as wire brush, scraper and sand paper from the surface of DG set canopy and painting the prepared surface with two coat of synthetic enamel paint of approved shade over a coat of red oxide primer, complete all as specified and directed by Engr-in-Charge.

Material and Labour for spray painting to DG set canopy of capacity 250-625 KVA by cleaning the existing old paint with the help of mechanical tools such as wire brush, scraper and sand paper from the surface of DG set canopy and painting the prepared surface with two coat of synthetic enamel paint of approved shade over a coat of red oxide primer, complete all as specified and directed by Engr-in-Charge.

Supply and fix microprocessor based multifunction controller with necessary accessories complete suitable for DG sets operation of capacity 15-30 KVA and showing the various parameters such as volt, ampere, frequency, RPM etc complete as per manufacturer of DG set with site requirement including removal of existing unserviceable one complete all specified and as directed.

Supply and fix microprocessor based multifunction controller with necessary accessories complete suitable for DG sets operation of capacity 62.5-110 KVA and showing the various parameters such as volt, ampere, frequency, RPM etc complete as per manufacturer of DG set with site requirement including removal of existing unserviceable one, complete all as specified and directed by Engr-in-Charge.

Supply and fix microprocessor based multifunction controller with necessary accessories complete suitable for DG sets operation of capacity 125-180 KVA and showing the various parameters such as volt, ampere, frequency, RPM etc complete as per manufacturer of DG set with site requirement including removal of existing unserviceable one, complete all as specified and directed by Engr-in-Charge.

Supply and fix microprocessor based multifunction controller with necessary accessories complete suitable for DG sets operation of capacity 200-320 KVA and showing the various parameters such as volt, ampere, frequency, RPM etc complete as per manufacturer of DG set with site requirement including removal of existing unserviceable one, complete all as specified and directed by Engr-in-Charge.

Supply and fix microprocessor based multifunction controller with necessary accessories complete suitable for DG sets operation of capacity 400 KVA and showing the various parameters such as volt, ampere, frequency, RPM etc complete as per manufacturer of DG set with site requirement including removal of existing unserviceable one, complete all as specified and directed by Engr-in-Charge.

Supply and fix microprocessor based multifunction controller with necessary accessories complete suitable for DG sets operation of capacity 500 KVA and showing the various parameters such as volt, ampere, frequency, RPM etc complete as per manufacturer of DG set with site requirement including removal of existing unserviceable one, complete all as specified and directed by Engr-in-Charge.

Supply and fix microprocessor based multifunction controller with necessary accessories complete suitable for DG sets operation of capacity 625 KVA and showing the various parameters such as volt, ampere, frequency, RPM etc complete as per manufacturer of DG set with site requirement including removal of existing unserviceable one, complete all as specified and directed by Engr-in-Charge.

Material and labour for SMPS (system main power supply) type control unit assembly suitable for 24 volts battery charger for including removal of existing unserviceable one, complete all as specified and directed by Engr-in-Charge.

Supply and fix for battery low maintenance lead acid of capacity 12 volts 180 AH with initial charging including removal of existing unserviceable one and hand over to store yard, complete all as specified and directed by Engr-in-Charge.

Supply and fix for battery low maintenance lead acid of capacity 12 volts 150 AH with initial charging including removal of existing unserviceable one and hand over to store yard, complete all as specified and directed by Engr-in-Charge.

Material and labour for carrying out repairs to AMF panel of 15 KVA to 200 KVA DG set at various installation including study, tracing out circuit, testing, replacing all defective parts, rewinding existing power and control wiring with same cables including testing and commissioning, complete all as specified and directed by Engr-in-Charge. Note: Spares like Volt meter, CT, power contactor required for repair will be measured and paid separately under relevant items.

Material and labour for carrying out repairs to AMF panel of 250 KVA to 625 KVA DG set at various installation including study, tracing out circuit, testing, replacing all defective parts, rewinding existing power and control wiring with same cables including testing and commissioning, complete all as specified and directed by Engr-in-Charge. Note: Spares like Volt meter, CT, power contactor required for repair will be measured and paid separately under relevant items.

Supply only for digital type frequency meter 96 x 96 mm flush/ square pattern, complete all as specified and directed by Engr-in-Charge.

Supply only for LED indicator lamps R, Y, B with holder 15 mm screw type, complete all as specified and directed by Engr-in-Charge.

Supply only for CT cast resin type of ratio 400/5 Amps of suitable VA burden, complete all as specified and directed by Engr-in-Charge.

Supply only for CT cast resin type of ratio 200/5 Amps of suitable VA burden, complete all as specified and directed by Engr-in-Charge.

Supply and fix for CT cast resin type of ratio 100/5 Amps of suitable VA burden including removal of existing unserviceable one, complete all as specified and directed by Engr-in-Charge.

Supply and fix 3 phase voltage monitoring relay DIN rail of suitable VA burden including removal of existing unserviceable one, complete all as specified and directed by Engr-in-Charge.

Supply & filling of Engine oil, multi grade premium Genuine oil 15W/ 40 as per manufacturer recommendations in DG sets, complete all as specified and directed by Engr-in-Charge.

Supply and applying for petroleum Jelly (01 Kg plastic sealed container) , complete all as specified and directed by Engr-in-Charge.

Supply and fill for distilled water for topping up in lead acid batteries and radiator, complete all as specified and directed by Engr-in-Charge.

Supply and fill for electrolyte of suitable specific gravity for lead acid batteries in sealed container, complete all as specified and directed by Engr-in-Charge.

Supply and fill for genuine coolant in 5 litres plastic sealed container for topping up in Radiator of DG set located at different locations, complete all as specified and directed by Engr-in-Charge.

Material and labour for battery leads of PVC insulated, multistranded, copper conductor of size 50 Sqmm of 1.25 metres long each duly fixed with brass clamps, copper lugs suitable for DG set batteries installed at different locations including removal of existing unserviceable one, complete all as specified and directed by Engr-in-Charge.

Material and labour for battery terminal brass clamps including removal of existing unserviceable one , complete all as specified and directed by Engr-in-Charge.

Supply & fix in repair of AVR suitable for following capacity of DG Sets, complete all as specified and directed by Engr-in-Charge :- (a) Up to 50 KVA DG set

(b) 62.5 to 125 KVA DG set

(c) 160 to 320 KVA DG set

(d) 400 to 625 KVA DG Set

Demolition of Cement concrete (unreinforced) in ground floor and paving not exc 15cm thickness (below or above ground level), complete all as specified and directed by Engr-in-Charge.

Material and Labour for Cement concrete type D-2, 1:4:8, using 40mm graded stone aggregate in foundation, filling and mass concrete etc, complete all as specified and directed by Engr-in-Charge.

Material and Labour for Sand filling under floor/pavement or in foundation including watering and consolidation, complete all as specified and directed by Engr-in-Charge.

Material and Labour for machine pressed precast concrete inter locking paver block (Reflective type) in any shape and size conforming to IS-15658-2006 of 80 mm thickness M-40 grade with grey cement and pigment including dismantling of old Stone slab/ interlocking tiles, complete all as specified and directed by Engr-in-Charge.

Demolition of PCC Block masonry built in cement mortar, complete all as specified and directed by Engr-in-Charge.

Material and Labour for pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width in type B1 (1:2:4) and setting in cement mortar (1:6), complete all as specified and directed by Engr-in-Charge.

Material and Labour for 15mm thick rendering in two (10mm+5mm ) CM 1:4 on fair faces of brick/concrete surfaces finished even and smooth without using extra cement, complete all as specified and directed by Engr-in-Charge.

Material and Labour for precast cement concrete in type B-1, 1:2:4 (20 mm graded aggregate) as in Kerb stone including weathering, slightly rounded or chamfered angles including form work all as directed including fixed in cement mortar 1:4, complete all as specified and directed by Engr-in-Charge. (Size of kerb stone as directed by Engr-in-Charge)

MC Gandhi and Sons (BID ID -3355020)

Sagar Electricals (BID ID -3355630)

M.K Enterprises (BID ID -3354929)

BALAJI TRADERS (BID ID -3355654)

D.N.PATIL (BID ID -3354601)

K A ELECTRIC CO (BID ID -3354659)

Bidder Name

MC Gandhi and Sons