SPECIAL REPAIR OF BLDG NO-1/C (TEMP) OF PT STORE AT THE SIKH LI REGT CENTRE AND PROVN OF DRAINAGE SYSTEM AT OFFICERS MESS OF THE SIKH LI REGT CENTRE FATEHGARH CANTT

Amount

Taking down cement plaster of any description, thickness on brick, stone, concrete surfaces including racking out joints, hacking for key, scrubbing down with water, removal of rubbish and cleaning, etc upto 6.00 mtr height complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (including taking down of backing plaster to brick / concrete wall surface), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. Laid, bedded and pointed in any mortar complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n. exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Demolition of cement concrete (reinforcement cut as required to facilitate demolition) of any description & in any position not specifically provided for complete all as specified and as directed

Demolition of brick work in cement mortar including all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) exc 1.50 sqm but n.exc 4.0 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc Including brick work of jambs and Cill in CM 1:4 complete all as specified and directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) n.exc 1.50 sqm each and removing from site including making good disturbed portions of wall with new or old bricks, lintel, cills etc Including brick work of jambs and Cill in CM 1:4 complete all as specified and directed.

M & L Non skid coloured ceramic joint less tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer of cement (1:6) complete.

M&L 20-25 mm thick machine cut kota stone as in flooring laid over 15mm th screed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing complete.

M & L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in plinth protection finish without using extra cement complete all as specified and directed.

M&L for brick work with sub class 'B' bricks old size bricks, straight or curved on plan exc. 6 m mean radius, built in CM (1:6) complete all as specified and directed.

All as per item No above but except bricks complete all as specified and directed.

M & L for 15mm thick rendering in cement mortar 1:6 on brick masonary wall surfaces on fair faces of brick masonary finished even and fair without using extra cement, upto 6.00 mtr height complete all as specified and directed.

M & L for 15mm thick rendering in cement mortar 1:4 on brick masonary wall surfaces or on other than fair faces of brick masonary finished even and fair without using extra cement upto 6.00 mtr height complete all as specified and directed.

M & L for rendering 5 mm thick in CM 1:3 as on concerete surface on ceilings finished even and smooth without using extra cement complete all as specified and directed.

M & L for preparation of new plastered surfaces of walls and applying two coat of oil bond distemper white or any tint over a coat of chalk whitening complete over prepared surface of 1mm thick wall care putty complete as specified and directed.

M & L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer and 1mm thick weather coat putty complete all as specified and as directed.

M & L for preparation of new plastered surfaces of ceiling and applying three coats of white wash on ceiling surfaces complete.

M & L for old surfaces complete removal of existing treatment surface and making surface smooth and applying two coats of OBD over prepared surface of 1mm thick wall care putty complete as specified and directed

M & L for complete removal of existing treatment surface and preparation of old plastered surfaces and making surface smooth and applying two coats of cement base paint over 1mm thick weather coat putty complete all as directed.

M & L for preparation of old plastered surfaces of ceiling by rubbing down and making surface smooth and applying two coats of white wash complete all as directed.

Removing existing water proofing treatment of any type all as directed by Engineer-in-charge and disposing off out side Defence Land .

M&L for cement concrete 1:3:6 type C1 (20mm graded stone aggregate) as in RCC roof surface with mixing of water proofing compound 3% by the weight cement to horizontal or vertical surfaces finished cement concrete surface even and smooth using extra cement including necessary form work Note:- (Water proofing compound will be measured separately)

M & L for preparation of newly plastered surfaces of roof including cleaning the surface by using wire brush/pressure hose and applying high performance polyurethane liquid membrane roof casting cold in two coats @ 1.5 Kg/Sqm with spray/brush an elogation of 300% to 700% and tensile strength not less than 3 N/Sqm as per ASTM D412 and ASTM D2370, crack bridging ability of 3.5mm as per ASTM C 1305, shore a hardness of not less than 60 as ASTMD 2240. The item includes epoxy prime applied @ 0.15 Kg/Sqm and a geotextile of 40 GSM to be applied over first coat while first coat is still wet complete as per manufacturer's instruction and sound engineering practice complete all as specified and directed. Note - work shall be executed by authorized applicator of manufacture as per manufacturer's instructions and roof height upto double storey building.

Supply only WPC

S&F factory made Steel Window 1.25mm thick Box Type (primer coated) ERW hollow P section of size 60mm x 25mm, 1.25 thick sheet single rebated comprises glazed Skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf consisting two Nos sash bar of T- Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T- Section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC ( 1:2:4) type B-1 Four Nos for each window) including following fitting welded to frame shutter: (a) Hold Fast, 150mm long of 12mm square bar made to shape – 04 Nos per window (b) Handles of Z Sec 100mm long (c) Stopper – 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mm x 63mm welded to hinges – 01 No per leaf (e) MS Pintal hinges of size 75mmx75mmx12mm-02 Nos per leaf (f) Fabrication & fixing arrangement as per TD. Note : Glass, and painting shall be measured and paid separately under appropriate item etc complete all as specified and directed.

S&F factory made Steel Window 1.25mm thick Box Type ( primer coated) ERW hollow P section of size 60mm x 25mm single rebated comprises gauged Skelton shutter ERW Sec 50mm x 20mm and 1mm thick with one or two openable leaf without sash bar of T- Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T- Section of size 60mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC ( 1:3:6) type C-1 Four Nos for each window) including following fitting welded to frame shutter: (a) Mild Steel Hold Fast,150mm long of 12mm Square bar made to shape – 04 Nos per window (b) Handles of Z Sec 20mm x 100mm long (c) stopper – 01 No per leaf (d) Cleat 55mm long of hollow square 15mm x 20mmx63mm welded to hinges – 01 No per leaf (e) Mild steel Pintal hinges of size 75mmx75mmx12mm-02 Nos per leaf (f) Grills made out of MS square bar 12mm welded to FI frame and 100mm spacing of guard bar complete all as specified and shown on drawings. Note: Wire mesh and painting shall be measured and paid separately under appropriate item etc complete all as specified and directed.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type prelaminated both side flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: Stainless steel butt hinges shall be paid separately)

S & F factory made 30mm thick 100% Solid WPC ( Wood polymer Composite ) Solid Prelaminated both side wiremesh Door Shutter of required size comprising of virgin PVC resin of K Value 57-60 (Suspension Grade), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded (Inner) with density not less than 650 kg/cum an ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N (Edge), Minimum Compressive Strength of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer - In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing company.

Supply & fixing factory made WPC door frame 100% Solid (wood polymer composite) Size 125mm x 65 mm double Rebated ,made from wpc material comparing of virign PVC polymer of K value 58-60 (suspension grade ) calcium carbonate and natural fibers ( wood powder / rice husk / wheat husk) minimum compressive strength of 58 N/mm2, modulus of elasticity 900N / Sqmm and resistance to spread of flame of class 'A' category with property of being termite / borer proof, water / moisture proof & fire retardant & fixed in postion with SS dash fasteners / hold fast of required dia and length, colour of door frame to match that of shutter all as per specifications drawings complete all as specified and directed.

S & F sheet glass ordinary quality 3 mm thick and glazing with oil putty or fixed with bead / glazing pins in squares n.exc. .5 sqm each pane all corner of glass to be fixed with silicon complete all as specified and directed.

S & F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or stainless wire staples, wodden beads to steel windows/wodden doors.

S&F Aluminium anodised barrel tower bolts of extruded section of 200mm size etc complete all as specified and directed.

S&F Aluminium handles, cast type anodised of size 150mm etc complete all as specified and directed.

S&F 250 mm long Aluminium alloy. Anodised, sliding door bolt with hasp, staple ( bolt type) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed

S & F in repairs stainless steel decorative curtain rod of 25 mm bore with 1mm thick including brakets 02 nos finalie 02 nos) etc complete all as specified and as directed.

M & L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed.

M & L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint etc complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 type D-2( using 40mm graded stone aggregate) as in flooring and mass concrete to complete all as specified and directed

M & L chequered cement concrete tiles of size 30 cm x 30 cm x 25 mm thick (as approved AGE(I) ) set, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles as in floor etc. including 15 mm thick cement screed bed in CM 1:6 etc complete all as specified and as directed.

Dismantling of (Plain, corrugated, semi corrugated, etc.) sheets in roof coverings complete all as specified and directed.

S & F Pre - Painted galvalume aluminium zinc coating GI based corrugated steel 0.50 mm thick of any colour as directed by AGE(I) having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

Dismantling wall and ceiling board,(fibre, pulp, insulation, etc.) or insulation boards / slabs / blankets, any thickness, including cover fillets of any description complete all as specified and directed.

S&F False Ceiling Horizontal level regular edge grid 600 x600 mm from work using hot dip sections and fixing tiles vinyl laminated MPL gypsum panels size 595x595x6 to 8mm thick after lamination, suspended the grid with grid hangers to Roof Truss / RCC Slab all as per manufactured instruction complete all as specified and directed.

M & L for reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) (nominal mix) as in slabs supported on wall, landing, balconies, canopies, deck slabs and in shelves and like in repair to Chajjas, Claddings, soffits etc including bonding agent, complete all as specified and directed. Note:- Reinforcement to be measured & paid under respective items.

M&L TMT bars 10mm dia and over cut to length bend to shape required including cranking, bending, spirally for hooping ends and binding with mild steel wire not less than 0.9 mm dia, complete all as specified.

M & L for form work to chullah hoods, chajjas, shelves, troughs and similar items including edges for rough finished surfaces of concrete flat, complete all as specified and directed.

M & L for PCC 1 : 3 : 6 type C1 using 20 mm graded stone aggregate as in fixing of hold fast including necessary form work complete all as specifed and directed.

S & F mild steel flat iron as in hold fast and similar small articles conforming to Fe 290 Gde E 165 complete all as specified and directed.

Dismantling wrought iron / Mild Steel work of any description not otherwise provided for complete all as specified and directed.

S & F for Rolled sections as in main gate and angle, for steel gate and plain sheet for gate hip and jack rafters;purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting platesconforming to Fe 410-W (Gde E-250) quality B complete all as specified and directed.

M&L for Brickwork with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in cm 1:4 including rendering 15 mm thick to brickwork in CM (1:4) finished even and smooth without using extra cement complete all as specified and directed.

M&L for cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as bed of drain etc including slightly rounded or chamfered angles including necessary form work complete all as specified and directed.

M&L for extra forming, fair, finished, drain or channel, 30cm inner girth in cement concrete using extra cement complete all as specified and directed.

M&L for pre-cast reinforced cement concrete as in cover slabs (1:2:4) type B1 using 20mm graded stone aggregate complete after placing in position over septic tanks/ manhole covers complete all as specified and directed .

Taking down copper/aluminium point wiring of any description and any position (light, fan, socket or power point) complete, including fixture and fittings such as switches,socket, ceiling rose,lamp holder,pendants, bracket and regulator etc and removing material from site including making good disturbed surface to match with the existing surface complete all as specified.

Taking down copper/aluminium sub main wiring and making good disturbed surfaces to match with the existing surface roof/wall/floor complete all as specified and as directed.

M&L for point wiring with 1100 volt grade PVC insulated and unsheathed 1.5 Sq mm (FRLS) multistranded copper conductor cable with continuous earth wire of 1.5 Sq mm (FRLS) multistranded copper conductor cable PVC insulated and unsheathed, drawn in & including concealed PVC rigid conduit medium grade with fittings (ISI marked) sunken pressed steel galvanised terminal boxes with top cover ISI marked plastic laminated hylam sheet for housing/ fixing switches etc for One light/ holder/fan/exhaust fan point controlled by one switch complete all as specified and directed for the following- Note- (i) The quoted rete is deemed to be included for the chases cutting. (ii) Cutting chases for concealed shall be made good using CM 1:4 and surface finished to match the existing surface & colour.

All as per item above here in before but for One 5 pin 5 Amp socket point on an independent board with 2.5 Sqmm (FRLS) copper conductor cable complete

All as per item above here in before but for One 5 pin 5 Amp socket point on same board.

All as per item above here in before but for one 16 Amp socket point independent with 4.0 Sqmm FRLS unsheathed copper conductor single core multistranded complete all as specified.

S&F Switch Piano flush type 5 Amp single pole one way complete all as specified and diercted.

S&F Socket 2 in 1, 3 Pin 5/6 Amp complete all as specified and diercted.

S&F Switch socket combination 2 in 1 flush type 16 Amp 5 Pin complete all as specified and diercted.

S&F electronic fan regulator 5 stepped type complete all as specified and diercted.

S&F ceiling rose PVC/Poly carbonate isolated body three terminal AC 230 volts complete all as specified and directed.

M&L for sub main wiring with two single core 6 Sqmm FRLS copper conductor PVC insulated and unsheathed cable including PVC conduit medium grade (appropriate size) concealed in wall for sub main connection including 6 Sqmm FRLS insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly all as specified. (Note :- Two runs of 6 sqmm FRLS and one run of 6 sqmm FRLS copper conductor shall be measured as one unit length.)

Supply and fixing in replacement of VTPN DB 12 way suitable for Mounting MCCB as Incomer of rating 100 Amp with suitable rated bus bar having IP-43 protection and double metal door including MCCB 100 Amps, AC, 415 Volt, 4 Pole, 16 KA with thermal magnetic trip unit (TMTU) adjustable thermal setting 0.7 - 1 x In, class II front face, Ics = 100% Icu as per IS/IEC 60947-2 complete all as specified and as directed.

Supply and fixing in repair of MCB distribution board SPN 240 Volt 8 way with 200 Amp rated bus bar having IP-43 protection and double metal door concealed in wall including connection with aluminium thimbles as required complete all as specified.

S&F of MCB SPN 63 Amp 240 volt 'C' curve complete all as specified and diercted.

S&F of MCB SP 6 to 32 Amp 240 Volt 'C' curve 10 KA complete all as specified and directed.

S&F of Reserve Plus Rechargeable Emergency Inverter LED Batten, 20-watt Compact 3-feet LED Tubelight, Cool Day Light complete all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

S & F building security LED Light 30 Watt sensor based made up pressure die-cast aluminium housing with high power LED as lighting source and lens embedded PC having top opening separate driver compartment with IP-65 protection and impact resistance of IK 07 for building secuity purpose with bracket size made of GI pipe medicum grade 40 mm dia 1.5 mtr long bend to shape as required and fixing with two nos MS Clamp of size 40x6 mm for fixing of builiding security light fittings completed all as specified and directed.

Supply and Laying cable XLPE Insulated screened PVC bedded, galvanized steel strip armoured service cable pole to building electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 Sqmm 4 core complete incl dismantling all as specified and directed.

S & F of 25 mm bore GI Tubing light grade with all fittings laid across road, in trenches or across PCC drain, along electric pole or floor/wall for cable protection with suitable size of MS Clapms and nut and bolts/washer complete incl dismentling all as specified and directed.

Sand cushioning to under ground cable in layers of 23cm thick ( 8cm before laying the cable and 15cm after laying the cable) in trenches including punning the sand up to 18cm thick and consolidated complete all as specified and directed. Note: Punned thickness only will be considered for payments

Supply and laying kiln burnt bricks best quality locally available old size sub class 'B' bricks laid flat in trenches with axis of brick perpendicular to the axis of cable for cable protection complete all as specified and as directed.

Excavation in trenches in soft /loose soil not exceeding 1.5 mtrs wide and not exceeding 1.5 mtrs in depth for drain , laying of cables including getting out in any type of soil complete all as specified and directed.

Returning filling in including spreading, leveling ,and well ramming, in layers not exceeding 25 cm each layer of any type of soil complete all as specified and directed.

Removing surplus excavated material from site not exceeding 50 mtrs from starting point and depositing where directed at level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

S&F in repair of metal plug & socket DB with metal plug and MCBs dobule pole and neutral enclosere with a two pin earth plug and socket suitable for 20 Amp complete with one single pole MCB complete all as specified and directed.

Taking down and Up of ceiling fan including accessories such as down rod, canopy and fan blade and refixing the same with flexible copper wire of size 23/0.0076 Sqmm upto 0.40 mtr with fan connector to ceiling rose complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick, burried directly into the ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to GI earth wire 4 mm dia by means of bolts, nuts, check nuts, and washers of galvanised iron or steel all as shown in electrical plate No - 3 connected to earthing test point all as specified or indicated including excavation and connected earth work, PCC chamber and cover, watering pipe, funnel wire mesh but without earth lead protection pipe and test on completion after dismantling unserviceable erthing (above GL only) complete all as directed. (Note :- On testing after completion if desired earth resistence is not obtained, the earthing will be redone at no extra cost.)

M/S S P CONSTRUCTION (BID ID -3349432)

avon electric engineering woks (BID ID -3346734)