CWE/GGN/GT-08/2021-22 IMPROVEMENT TO SMQ (PHASE-II) AT 25 WG AF (RAJOKRI) UNDER GE (AF) GURGAON

Amount

Demolition of cement concrete (un-reinforced) of any description & in any position not specifically provided complete including dismantling of floor tiles etc complete all as specified and as directed

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description in any position not specifically provided complete including dismantling of floor tiles etc complete all as specified and as directed

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site complete all as specified and as directed

M&L for 25 mm thick PCC 1 :2 :4 type B-0 (using 12.50mm graded stone aggregate) as in sub base complete all as specified & as directed.

M&L for screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 for bedding of tiles complete all as specified and as directed.

M&L for screed bed or bedding layer of mortar 20mm thick in cement mortar 1:6 for bedding of tiles complete all as specified and as directed.

M&L for cement concrete 1:5:10 type E-2 using 40mm graded stone aggregates as in sunken portion of WC etc complete all as specified and as directed

M&L for cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate as in coping benching, slightly rounded and similar items complete all as specified and as directed.

M&L 10 mm thick rendering in cement mortar 1:4 on vertical surfaces for backing of tiles etc complete all as specified and as directed.

M&L Glazed ceramic tiles in vertical surface coloured 300mmx 450mm , 6-7mm thick, jointfree, set and jointed in neat cement slurry and pointed in white or colour cement to match etc complete all as specified and and as directed

M&L for Non- skid ceramic coloured tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.11 but n.exc 0.18 Sqm, jointfree, fixing in floors/skirting etc, set and jointed in neat cement slury and pointed in white or coloured cement to match complete all as specified and directed

M&L for Non- skid ceramic coloured tiles 7 to 8mm thick (Square/ rectangular) area of each tile exceeding 0.06 but n.exc 0.11 Sqm, jointfree, fixing in floors, set and jointed in neat cement slury and pointed in white or coloured cement to match complete all as specified and directed

M & L Machine cut kota stone slab flooring 20 -25 mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polish complete all as specified and as directed

M&L Chequered cement concrete coloured tiles 30 cmx30 cmx25mm, set jointed and pointed in neat cement slurry in floors with grey cement and pigment complete all as specified and directed.

M & L Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polish complete all as specified and as directed

Demolition of brick work or rubbled stone masonry including all quoins arches , pillars etc built in cement mortar and including removal from the site complete all as specified and as directed

M&L for brick work with sub class ‘B’ bricks straight or curved on plan in cement mortar 1:4 as in half brick thick walls complete all as specified and as directed

M&L brick work with sub work with sub class 'B' brick straight or curved on plan exc 6m mean radius build in cement mortar 1:6 complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar (1:6) on fair faces of brick work or concrete surface on walls finsihed even and smooth (without using extra cement) etc complete all as specified and as directed

M&L for rendering 15mm thick in cement mortar 1:4 on brick or concrete surfaces including rendering on fins, fascias, chajja, parapets etc and finishing the surfaces even and fair finish (without using extra cement) complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar (1:3) on fair faces of brick work or concrete on ceiling surface etc complete all as specified and as directed

M&L for preparing new plastered surface of walls and applying two coat of oil bound distemper on white or any tint etc over a coat of chalk whiting primer complete as specified and directed

M&L for preparing newely plastered surface of wall and applying two coat of cement base paint etc complete all as specified and as directed

M&L for preparation of newly plastered or unplastered/undecorated surface of Ceiling and applying two coats of Oil Bound distemper over one coat of primer complete all as specified

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but n.exc 4.00 Sqm each, including cutting holes for removing the hold fast etc. (disturbed surface of wall shall be make good by the contractor. the rate quoted shall be deemed included for the same) complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each, including cutting holes for removing the hold fast etc. (disturbed surface of wall shall be make good by the contractor. the rate quoted shall be deemed included for the same) complete all as specified and directed.

S&F 1.25 mm thick pressed steel frame of size 165 X 60 mm for door with one or more rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed

S&F 1.25 mm thick pressed steel frame of size 105X 60 mm for door with one or more rebate includings necessary fixing lugs, hinges, locks strike plate etc complete all as specified and as directed

M&L cement concrete Type C1, 1:3:6 using 20 mm graded stone aggregate as in filling of door frames of pressed steel and in bed blocks etc complete all as specified and as directed.

S & F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. Square tube in opening etc complete all as specified and as directed

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm wide stuck inside with solvent cement for style and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail : panelling of plain colour PVC sheet to be fitted in the MS frame wealded/sealed to the style & rails with suitable PVC sheet beading, and joined together with solvent cement, in the frame a site as per specification and drawing etc complete all as specified and as directed

S&F power coated Box type (steel) window / ventiliators (Double shutter, guazed and glass) as per drawing No CEAF/STD-171/07 sheet No 1/1 to 4/4 dated 05.11.2007, fixed with dash through bolts of standard quality, 100 mm long aluminium handle in each shutter, 2 Nos alumimium tower bolts of 150 mm long & 2 Nos hinges of each shutter of 100 mm length etc including 4 mm thick sheet glass for window shutter and 4 mm thick frosted glass for ventillators, 0.36 mm stainless steel wire cloth with 1.40 mm aperature, mild steel 12 mm square bar for guard bar/grills with frame including painting & opening for cooler space where required etc complete all as specified and as directed

S&F 2nd class HW rail & style factory made plain, framed panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated etc complete all as specified and as directed.

S & F 2nd class hardwood factory made 35 mm thick made glazed and skeleton shutters open rebated and prepared to rceieve glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as spfd in SSR Part-1, Section 8, clause 8.24 (a) etc complete all as specified and as directed

S&F factory made 35mm thick flush shutters solid core construction with block board core and plywood face pannel commercial type on both faces complete all as specified and as directed.

S&F 25mm thick flush shutters, as in cupboard , solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed

S&F 75 mm butt hinges, medium weight, cold rolled mild steel and fixed etc complete all as specified and as directed

S&F 100 mm size but hinges type C-21 extruded aluminium alloy with galvanised mild steel hing pin, anodised and fixed, complete all as specified and as directed

S&F Aluminium anodised tower bolt 200 mm long of extruded section etc complete all as specified and as directed

S&F 150 mm long aluminium anodised, barrel tower bolts of extruded section. Complete all as specified and as directed

S&F 150 mm long Extruded aluminium alloy handles, fabricated type, anodised etc complete all as specified and as directed

S&F aluminium alloy, anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy etc complete all as specified and as directed

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple including necessary beading complete all as specified and as directed

M&L preparing new wooden surface of any description, not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer etc complete all as specified and as directed

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint etc complete all as specified and as directed

Dismantling boarding of any description , fixed in any position with nails complete all as specified and as directed.

S&F 18 to 19mm thick block board grade 2 quality interior grade decorative type with decorative face veneer on one face fixed with screws to timber framework as in shelves, drawers etc complete all as specified and as directed.

S&F plain fillets, square, rectangular or triangular in section clean sawn secured with nails or brads 2nd class HW sectional area exc 13 Sqcm & n.exc 25 sqcm

M & L preparing new wood or wood based surfaces of any description n.exc 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F 18 /19 mm thick Prelaminated particle board, interior grade,prelaminated oneside with decorative choice lamination & other side balancing white lamination,fixed with screws to etc complete all as specified and as directed

S & F Continuous (piano) hinges, mild steel, bright finish or electro galvanised Width of flaps in 40mm complete all as specified and as directed

S&F 100 mm long Extruded aluminium alloy handles, fabricated type, anodised etc complete all as specified and as directed

M&L for RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns, in floors, roofs, landing balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in Chajjas complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in Fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels, balustrade, and the like complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 5 mm dia and over up to and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed.

S & F in repair 110 mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to walls complete all as specified

S & F in repair 110 mm dia PVC (SWR)bends with rubber rings joints fixed as required complete all as specified and as directed

S&F double legged floor door stopper aluminium alloy with rubber etc complete all as specified and as directed

S &F Hasp and staple, size 100mm safety type,brass with mild steel hinge pin including bolt to hinge plate and fixed with screws etc complete all as specified

M&L for use and waste form work to soffits of suspended slab such as roof slabs, floor slabs, landing and similar works, not exceeding 200mm thick for rough finished in flat surfaces of concrete complete all as specified and directed.

M&L for use and waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished in flat surfaces of concrete complete all as specified and directed.

M&L for use and waste form work to Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter for rough finished in flat surfaces of concrete complete all as specified and directed.

M&L for use and waste form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs, sides of RCC/PCC bands in walls, horizontal or sloping and similar works exc 10 cm but not exc. 20 cm wide for rough finished surfaces of concrete complete all as specified and directed.

S&F in repair vitreous china squatting pan “ORISSA” pattern size 580mm X 440mm, white with P or S trap front or back inlet with integral foot rest (excl flushing cistern & flush pipe) & including connection to trap & to flushing pipe anti syphonage pipe etc complete including making good to floor complete all as specified & as directed.

S&F in repair white vitreous china wash basin white flat back size 550x400 excluding taps but including 32 mm dia chromium plated waste fitting and PVC waste pipe 610 mm long and MS brackets complete all as specified and as directed

S&F in repair sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; ncluding bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe,overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed

S&F in repair tubular towel rail 20mm dia type brass chrormium plated 600mm long between flanges complete all as specified and as directed

S&F in repair chromium plated shower roses of 125 mm size with arm with/without swivel joints of standard size including fixing to 15mm steel pipe or union complete all as specified and as directed

S&F in repairs PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action type with inlet ball valve and float, handle with & including bracket and PVC flush pipe 32 mm bore complete all as specified and directed

S&F in repair bib tap fancy type cast copper alloy chromium plated with crutch or butterfly handle screwed down screwed for iron pipe or brass ferrule or fixed for 15 mm dia bore pipe complete all as specified and as directed

S&F in repair stop valves/angle valves fancy type chromium plated brass cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions fixed for 15 mm dia bore pipe complete all as specified and as directed

S&F as in repair 15mm bore Pillar taps fancy type, cast copper alloy, with long swan neck , chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed all as specified and as directed

S&F in repair PVC connection of 45 cm length including brass nuts complete all as specified and as directed

S&F in repair PVC (SWR) floor trap plain with grating having dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified & as directed.

S&F in repair salt glazed stone ware gully trap of size (150x150mm) square or round mouthed traps "P" including demolition of old gully trap complete all as specified and directed

Taking up or down steel tubing 15mm bore and connection including cleaning for refixing or removal to store. complete all as specified and directed

All as above item No 81.00 hereinbefore but of 20mm dia .

Cutting chases, pinning in. making good to facings where required andpointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall etc complete all as specified and as directed

Supplying and laying of CPVC pipes 16mm outer diameter, SDR 11 and plain CPVC SDR 11 fittings on walls/ceilings or laying in floors complete all as specified and as directed

Supplying and laying of CPVC pipes 20 mm outer diameter, SDR 11 and plain CPVC SDR 11 fittings on walls/ceilings or laying in floors complete all as specified and as directed

Dismantling of cast iron pipe up to 100 mm dia, jointed in cement mortar and taking out of trenches/Wall if required etc complete all as specified and directed

S&F 100 mm bore Cast iron soil, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches, complete all as specified and as directed

S&F 100 mm bore Cast iron soil, waste and vent pipes, in any length with or without ears with cement joints, fixed in walls, complete all as specified and as directed

S&F in repair for 75 mm bore Cast iron soil, waste and vent pipes, in any length with or without ears with cement joints, laid in trenches or in floors or fixed to wall vertically complete all as specified and as directed

S&F in repair 75mm bore cast iron Bends of (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and as directed

S&F in repair 75mm bore cast iron Bends of (any radius), diminishing pieces or tapers (larger bore measured) with acess oval door complete all as specified and as directed

S&F 100 mm bore cast iron Bends of (any radius), diminishing piecs or tapers (larger bore measured) complete all as specified and as directed

S&F in repair CI branch pieces 75 mm dia double (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches fitted with oval acess door complete all as specified and directed.

S&F in repair CI branch pieces 100 mm dia double (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches fitted with oval acess door complete all as specified and directed.

S&F 100 mm cast iron cowls complete all as specified and as directed

S&F in repair kitchen plate rack stainless steel 1 mm thick of size 60cmx75cm complete fixed to brick/concrete wall, with screw including rawl plug complete all as specified and as directed

Dismantling water tanks exc.250 ltr but not exc 500 ltr and removing to store

S&F double layered rotational moulded polyethylene water storage tank of capacity 500 Ltr (cylindrical vertical with closed top cover), hoisted and fixed in position all specified in SSR part –I ( 1991) complete all as specified and as directed by Engineer-in-Charge Note : The cost of accessories like inlet and out let pipe ball valve to air vent pipe shall be measured and paid separately under concerned item nothing extra admissible on this account

S & Fixed in repair ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe of 20 mm bore and fixed, complete all as specified and directed.

S&F as in repair Gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe 20 mm bore and fixed as in repair complete all as specified and as directed

Demolition of Mud in roofs, any thickness including plastering and leeping,(whether full thickness removed etc complete all as specified and as directed.

Dismantling Bricks (laid flat or on edge) or brick tiles in laid bedded in any mortar on floors, channels,kerbs, aprons, etc. (each layer) complete all as specified and as directed

Cutting holes into or through brick/stone masonry walls built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall exc. half brick but not exc one brick etc complete all as specified and directed

M&L for rendering 15 mm thick in CM (1:4) on fair faces of brick work or concrete surface finished even and fair mixed with water proofing compound as per manufacture instruction etc complete all as specified and as directed Notes : WPC shall be measured and paid seperately

M & L for water proofing treatment with APP (Atactic Poly propylene) modified polymeric membrance over roof consisting of cleaning of concrete or plaster surface of roof & parapet walls and applying evenly a bitumen primer confirming to IS 3488 @ 0.40 Kg per per sqm followed by a tack coat @ 1.2 Kg per sqm using 85/28 grade industrial hot blown bitumen over it laid with APP modified polymeric water proofing membrance minimum weigth 3.6 Kg/Sqm reinforced with non-woven polyester fabric (weigth not less than 160 grams per sqm) unrolled and bonded to substrate with longitudinal and end laps 100 mm as per manufacturer's instructions complete all as specified and directed.

Supply only integral water proofing compound

Cutting grooves in brick wall 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed.

M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in coping or roof kerbs on roof chamfered on edge including troweling slightly complete all as specified and as directed.

M&L for rendering 5 mm thick in CM (1:3) on fair faces of concrete surface etc complete all as specified and as directed

M&L for guniting work to RCC work in column, flooring, side walls, beam, slab, etc by removing loose concrete cover etc, cleaning of surface with wire brush and applying epoxy paint to rusted reinforcement and S&F welded wire mesh fabric or wire net less than 95 X 95X 3 mm adhesive, plaster grade for concrete admixture 1 part of cement and 3.5 part of sand and average thickness 40 mm and making the surface even including 15mm thick plastering in CM 1:4 on brick or concrete surfaces including finishing the surfaces even and smooth, without using extra cement plumb and making surface true to geometry in line and including necessary form work to be carried at upto double story building Note.- Where ever reinforcement required will be measured and paid separately etc complete all as specified and directed by Engr-in -charge.

M&L for rendering 15 mm thick in CM (1:3) mixed with water proofing compound @ 3% by weight of cement finished even and smooth without using extra cement in sunken portion of toilet including one coat of bitumen coating of bitumen 85/25 grade at the rate of 1.2 kg per sqm including cleaning surfaces etc complete all as specified and as directed. Note: WPC will be measured and paid separately

M & L Udhaipur green Marble work 18-20 mm thick table rubbed and polished) in cooking platforms, jambs, window cills etc in cement mortar !:4 including pointing in white cement(1:2) using marble dust with admiture pointing to match with marble shade other than white and black complete all as specified and as directed

M&L for preparation of plastered or unplastered old decorated surfaces of walls by brooming down or steel wire brushing scrapping down smoke spot moulds moss and efflorescent salts and treating oily & greasy spots and filling of holes and cracks with with suitable material like cement or plaster of paris etc and thereafter applying two coat of oil bound distemper complete all as specified and as directed.

All as per item No 113 above but on surfaces of ceiling.

M&L for preparation of plastered or unplastered old decorated surfaces of walls by brooming down or steel wire brushing scrapping down smoke spot moulds moss and efflorescent salts and treating oily & greasy spots and filling of holes and cracks with with suitable material like cement or plaster of paris etc and thereafter applying two coat of Cement base paint complete all as specified and as directed.

M&L preparation of old painted surfaces of wood & wood based of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L preparation of old painted surfaces of steel of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

S&F mild steel helical door spring 150 mm longe ordinary rat tail type incl roller and roller plate complete fixed with screws to wooden frames or with welding to steel frames complete all as specified and directed

M &L of filling holes in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed.

M&L Providing and injecting chemical emulsion for Post Constructional Anti termite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300 mm including excavating channel along the wall and rodding etc. complete all as specified and directed.

M&L Providing and injecting chemical emulsion for Post Constructional Anti termite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed.

S&F in repair 19 mm thick Aluminium curtain rod with powder coated alongwith ornamental attachement at both ends and one set of ornamental decorative MS clamps to fixed to walls complete all as specified and directed

M&L for PCC 1:3:6 type C-1 (using 20mm graded stone aggreate), as in plinth protection including cement complete all as specified & directed.

S&F door seals made of aluminium strip powder coated 20 mm wide and provided rubber/ cotton mat lining fixed with screws to door shutters up to 1 mtr width opening complete all as specified and as directed.

S&F Corner glass shelf (with bracket) , fancy type with stainless steel railing fixed to wall with rawl plugs and chromium plated screws complete all as specified and directed.

S&F Brass CP wall mixer for mixing hot & cold 'water screwed down for bore of 15 mm iron pipe and fixed complete all as specified and as directed

S&F MS framed brackets of angles or tees with web and flanges cut to shape,drilled and counter sunk for screw,including bending and welding angles as necessary and similar work conforming to Fe-290, gde E-165. complete all as specified and as directed

Cutting holes into or through brick/stone masonry walls built in cement mortar and making good in cement mortar 1:3 or cemnt concrete 1:2:4 type B-1 as required Depth of embedded portion of holdfasts or lugs measured from the face of the jamb into the wall Exc. half brick but not exc one brick etc complete all as specified and directed

S & F Pre-painting galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ clading to wall fixed with self tapping screws complete all as specified

S&F in repair 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specifed and as direected

S&F in repair 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specifed and as direected

S&F in repair 75 mm bore PVC (SWR) bends any radius as required and jointed with approved adhesive complete all as specified & directed.

S&F in repair 110mm bore PVC (SWR) junction single, (single T) equal or unequal with access door as required and jointed with approved adhesive complete all as specified & directed

S&F in repair 75 mm bore PVC (SWR) junction single, (single T) equal or unequal with access door as required and jointed with approved adhesive complete all as specified & directed

S&F in repair 110mm bore PVC (SWR) vent cowl.

S&F framed work such as grills gratings, etc with ends of bar shouldered and/or revited or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings framework of water tanks and similar works confirming to Fe 290 Gde E-165 complete all as specified

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed.

M&L for cement concrete tiles 250 mm x 250 mm x 22mm thick machine pressed set jointed and pointed in neat coment slurry in floors and cut and polished with grey cement and no pigment over Complete all as specified and directed. .

M&L Formwork to soffits of suspended slabs such as roof slabs, floorslabs, landings and similar work;not exceeding 200mm thick horizonal or sloping in rough finished concrete surface complete all as specified

M&L three coats of white wash on ceiling on new plastered surfaces including preparation of surfaces complete all as specified and as directed

Taking down of existing old damaged Valve, stop, screwed,20 mm/ Cock, bib, brass, 15 mm dia all as specified.

Supply,fixing and testing Gun metal gate valve 20mm ,screwed body ends and cast iron hand wheel conforming to IS 778-1984 ans ISI marked complete all as specified and directed.

M&L for cutting /removing existing steel tubing conection from main line up to 50 mm size and screwing new conection for 20 mm bore GI medium grade pipe complete all as specified & directed

M&L for cutting /removing existing steel tubing conection from main line up to 50 mm size and screwing new conection for 15 mm bore GI medium grade pipe complete all as specified & directed

Taking down carefully copper/aluminium point wiring (light, Fan, Socket or power) fitting such as switches, ceiling roses, pendents, regulators, sockets etc complete removing material to store for keeping in safe custody for reuse or takeing in schedule of credit and making good disturbed surfaces of walls, floors etc all as specified as directed.

Dismantling and taking down fluorescent tube light single/double of any wattage or size street light fittings for repair or replacement of burnt/worn out accessories or carrying to MES store for reuse or takeing in schedule of credit (Accessories or components to be provided free for replacement by department)

Taking down unserviceable sub main wiring of any type/size including wires, conduits/battens etc complete all as specified and directed by Engr-in-Charge.

Taking down unserviceable / serviciable MCB DB's/AC's box to deposit in store for keeping in safe custody for reuse or takeing in schedule of credit of any size/rating complete all as specified and directed by Engr-in-charge.

M & L for point wiring with 1.5 Sqmm (nominal area) for PVC insulated FRLS grade, unsheathed copper cable multi standard conductor 1100 Volts grade confirming to IS 694 with colour coding, Red for phase, Black for neutral and Green cable used for earthing connection, controlled by one way switch drawn through in and including 20mm dia non metallic PVC conduit ISI marked with all accessories Tee, Junction box including 1.5 Sqmm PVC rigid (FRLS) insulated unsheathed copper cable multi standard conductor 1100 Volts grade confirming to IS 694 for continuity earth wire connected to each point and terminated into sunken cast pressed steel terminal box made out of MS sheet 1.3mm thick for mounting of switches, Switch socket outlet and fan regulator with 03mm thick plastic laminated sheet including making good, disturbed surface as before work complete all as specified and directed. Note : Cutting in wall for to accommodate concealed PVC tube only to be done with electric wall cutter machine. Being load bearing wall manually cutting in wall is strictly prohibited

One light point controlled by one way switch.

One ceiling fan/exhaust fan/Air ciculator /bell point controlled by one way switch.

one light point controlled by 2, two way switch.

One three/5 Amp Socket outlet 5 Amp controlled by one way switch on the same board, complete all as specified.

One 3/5 pin Socket outlet 5 Amp controlled by one way switch on independent board , complete all as specified and directed.

M&L for point wiring with two runs of FRLS PVC insulated unsheathed, 1100 V grade cable multi stranded copper conductor of size 2.5 sqmm drawn through in and including concealed PVC conduit size of not less than 25mm concecled in wall / surface including provn of pressed steel terminal box of suitable size with 3mm thick plastic laminated sheet cover for mounting switch, socket and regulator along with earth wire of PVC insulated, unseathed, 1100 V grade cable multi stranded copper conductor of size 2.5 sqmm and for one 6 pin socket outlet two in one 16/6 amps on an indeendent board including colour coding of cable shall be Phase- Red, Neutral- Black and Earth- Green and making good, disturb surface as it is complete all as specified and directed by for the following.

M&L for point wiring with two runs of FRLS PVC insulated unsheathed, 1100 V grade cable multi stranded copper conductor of size 4 sqmm drawn through in and including concealed PVC conduit size of not less than 20mm concecled in wall / surface including provn of pressed steel terminal box of suitable size with 3mm thick plastic laminated sheet cover for mounting switch, socket and regulator along with earth wire of PVC insulated, unseathed, 1100 Volts, FRLS type, multi stranded copper conductor cable of size 4 sqmm for AC box including colour coding of cable shall be Phase- Red, Neutral- Black and Earth- Green and making good, disturb surface as it is complete all as specified and directed by for the following. Note : Rates are deemed to be included for chases of conduit and sunking for single pole and neutral enclosure boxes cutting and making holes in wall/floor for passing in or through conduit from DB to existing location

S & F for socket 5 amps 5 pin flush type, 240 volts. with polycarbonate body. complete all as specified and directed..

Fixing only old serviciable socket 5 amps 5 pin flush type, 240 volts. Required screw, nut, bolt or cable are included in quoted rate complete all as specified and directed..

S & F for socket out let, 6 pin 5 and 15 amps multi purpose 2 in 1 flush type, 230 volts with polycarbonate body.complete all as specified and directed.

Fixing only old serviciable socket out let, 6 pin 5 and 15 amps multi purpose 2 in 1 flush type, 230 volts with polycarbonate body. Required screw, nut, bolt or cable are included in quoted rate complete all as specified and directed..

S&F sheet metal enclosure single pole and neutral two pin and earth plug and socket complete with one single pole MCB SP 20 Amps for geyser complete all as specified and as directed.Cat Pat NO- 811955+ 811127 of Indoasian (Optipro), Havells or equivalent in approved makes.

S & F for of piano switch flush type with polycarbonate body single pole one way 5 amps 240 volts complete all as specified and directed..

Fixing only old serviciable switch piano flush button single pole one way 5 amps 240 volts with polycarbonate body. Required screw, nut, bolt or cable are included in quoted rate, complete all as specified and directed..

S & F of piano switch flush type single pole two way 15 Amp 240 volts with polycarbonate body complete all as specified and directed..

S & F for call bell push flush button single pole one way 5 amps 240 volts with polycarbonate body complete all as specified and as directed.

S & F for electric call bell heavy duty Ding Dong type 230 volts single pole complete all as specified and as directed.

Fixing only old serviciable electric call bell heavy duty Ding Dong type 230 volts single pole Required screw, nut, bolt or cable are included in quoted rate, complete and all as specified and directed

S&F in replaceent of MCB DB sheet metal enclosure single pole and neutral 240V with 200 Amp suitable size plate and common neutral link all enclosed in standard steel sheet flush mounting type factory fabricated Acrylic single door complete confirming to IP 43 without MCB and with enclosure blank plates for unused way suitable for 8 way complete all as specified and directed : Cat Pat No 811818 of Indoasian, Legrand or equivalant in approved makes.

All as per item No 163 above but 4 way, complete all as specified.

S&F MCB, single pole & neutral, 240 Volts 40 Amps,10KA B series complete all as specified and directed .Make:-811152 of indoasian, Hager/ Legrand or equivalant in approved makes

Fixing only old serviciable MCB, single pole & neutral, 240 Volts 40 Amps,10KA B series complete all as specified and directed.

S&F MCB, single pole, 240 Volts (05 to 32) Amps,10KA, B series complete all as specified and directed Make:- Indoasian, Legrand or equivalent in approved makes.

Fixing only old serviciable MCB, single pole, 240 Volts (05 to 32) Amps,10KA, B series of any make complete all as specified and directed

S & F LED light fitting 1 x 18 watt, 220v AC decorative box type with driver holder including LED tube light connecting up with 03 core flexible cooper conductor cable of suitbale size from ceiling rose complete all as specified and directed. Make : Phillips, Bajaj, CG or equivalent in approved makes.

Fixing only old serviciable LED light Batten Fitting 1x18 watt fitting including 1x18 watt LED tube connecting with twin core copper conductor. Required screw, nut, bolt or cable are included in quoted rate, all as specified and as directed .

Supply and fix Mirror LED light 1x8 watt fitting including 1x8 watt LED tube connecting with twin core copper conductor all as specified and as directed .Make :- Phillips/ Bajaj/CG or equivalent in approved makes.

M&L in replacement for sub main wiring with two run of single pole core 6 sqmm, FRLS grade, multi stranded copper conductor PVC insulated and unsheathed cable ISI marked drawn through 25 mm dia, medium grade, PVC conduit concealed in wall for sub main connection with single run 6 Sqmm PVC insulated unsheathed copper conductor ISI marked as earth wire complete all as specified and directed by Engr-in-charge.

Taking down and fixing only ceiling fans after painting and Necessary repairs / servicing including replacement of hanging assambly , bush bearing , U/S capacitor, flexible copper cord three core PVC sheathed of size 23/0.0076 of required length from ceiling rose or connector to ceiling fan for giving connection complete all as specified and as directed by Engineer-in-Charge.

Taking down and fixing Fixing only Exhaust fans after painting and Necessary repairs / servicing including replacement of bush bearing , U/S capacitor flexible copper cord three core PVC sheathed of size 23/0.0076 of required length from ceiling rose or connector to exhaust Fan for giving connection complete all as specified and as directed by Engineer-in-Charge.

S&F ceiling rose, surface bakelite, size as per relevant IS, three terminals complete all as specified and directed

S & F Lamp holder insulated body with back plate for batten fittings.with polycarbonate body complete all as specified and as directed.

S & F LED Glass bulbs of 12 W in lamp holder complete all as specified and as directed. Make :- Phillips/ Bajaj/CG or equivalent in approved makes.

M&L for earthing complete with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mtr below ground level) with top edge of earth plate not less than 1.5 Mtrs below ground level connected to GI wire 4 mm Dia as earth lead by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, including PCC (concrete chamber) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate, with fair finish internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire gauge mesh, 80 mm thick RCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) and specified including provision 20 mm dia medium grade pipe and watering pipe shall be 20mm bore medium grade, and including all excavation and earth work & connecting the earthing to an earthing test point complete all as specified & directed . NOTE: (i) The concrete pit shall be PCC 1:3:6 type C-140 mm thick pre cast cover slab of RCC(1:2:4) type B-1 using 20 mm graded stone aggregate reinforced with 8 mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in the electrical plate No.3 of MES SSR Part -1 (ii) item includes the cost of 7.5 m GI pipe for protection of earth strip. (iii) PCC pits extra cost of addtional length of watering pipe,bends elbows etc.shall be deemed to be included in the quioted rate. (iv) Item includes the cost of 7.5 mtr length Galvised earth strip 25x4 mm.

S&F For ceiling fan regulator stepped electronic type 300 watt rating, 230 volts with polycarbonate body all as directed.

Fixing only for ceiling fan regulator stepped electronic type 300 watt rating, 230 volts with polycarbonate body. Required screw, nut, bolt or cable are included in quoted rate, complete all as directed.

Supply, install , testing & commissioning of Meter box sutable for 4 Nos of meter, Provision for fixing of MCCB 100 Amp Four pole & 3 Nos of LED indicator Kiosk type ,LT(415 Volts, 50 Hz , 3-phase, 4 wire supply) wall mounted , factory assembled, indoor type weather and vermin proof (Protection Class IP-54) made out of 3.15 mm thick MS Sheet CRCA sheet with front hinged opening, rubber lining, locking arrangement ,powder coated externally and internally after seven tanks treatment, fully compartmentalized design comple with 4 Nos aluminium strip bus bars air insulated and PVC sheathed capacity 100 Amps with colour coding & complete all as specified and as directed.

S&F MCCB, Three pole & neutral, 415 Volts 63-100 Amps,25KA complete all as specified and directed .Make:- Indoasian/HPL/Havells Make :- Catpart No 830050 of Indoasian/Hager/ Legrand or equivalent in approved makes.

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 6 sqmm galvanised iron or steel wire complete all as specified and directed

S&F LED security light fitting 35/36 Watt, having uniformty ratio 0.25 , high pressure die cast aluminium housing , heat resistant toughened glass frame , IP-65 protection complete with lamp & connected items and connection with suitable cable from celing rose to light fitting and including fixing on GI pipe bracket made out of suitable dia gi pipe medium grade 1.2 m long bend to shape and fixed on wall with flat iron clamps nut, bolts washers etc specified and directed

Supply & fix exhaust fans single phase 230/ 240 V of size 300 mm sweep with louver, 1400 RPM, Steel body including making necessary conection with two core, 23/.0076 PVC sheathed copper conductor, resizing wall hole as per requirement and making good distrubed surface with cement mortar thereafter if required complete all as specified & directed .

Net Contract Sum will be after deducting Sch of Credit of Rs 10,87,239.00

SARINS

PK Constructions