Modification of Conference Room and other AAI offices at ATS Complex Mumbai.

Amount

Supplying and applying UV digitally reproduced print on (EFI Vutek or Durst or VIRTU Printing Platform) using OEM approved ink for longer durability decorative graphics printed on textured self adhesive Vinyl of (180 Micron +/- 10 %) (Make 3M/ LX Hausys / ARLON).The graphics shall be approved by AAI. The finished graphics installed over the existing wall/partition. In case of Undulation in Wall / Surface 5 mm thick Sunboard to be used to make surface smooth. Mode of measurement on the actual installed area. (Sunboard to be paid separately). Graphics cost to be inclusive of material, printing and execution. Cost to include downloading the high resolution graphics good for printing from web and printing the same with desired colour scheme on vinyl as per approval. Graphics installation to be bubble free with no distortion in image quality /colours. 5 years OEM Digital warranty to be provided against Ink Fading, Peel off, Excessive Shrinkage etc. all complete as per the direction of Engineer-in-charge.

Supply and Apply of pre pattern Decorative Interior film (Make 3M/ LX Hausys/ARLON) in various patterns ( like Wood, Stone, Marble, Mettalic etc.) as approved by AAI. Film should have thickness of 200 +/- 10 % (Micron) having Fire Retardant Properties to ensure safety in case of Fire. Self adhesive film to be competible to be pasted on any smooth surface (Including Wall, Furniture, Door, Ceiling, Elavators etc). 5 years OEM Digital warranty to be provided against Pattern Fading, Peel off etc. While pasting the film 10mm overlapping is recommended at joint (avoiding butt joint) etc. all complete as per the direction of Engineer-in-charge

Providing and fixing Sun board using 3M tape, feviquick, and silicon etc.all complete as per the direction of Engineer-In-Charge.

Providing & Fixing UV Printed Ultraclear Film on Transperent Glasses. Film Thickness 50 Micron with ultraclear adhesive ( Make 3M/ LX Hausys/ARLON) . Printing should be done with Eco Friendly UV Digital Printing on (EFI VUTEK or Durst printing or VIRTU Printing Platform) using OEM Approved Ink for longer durability. 5 years OEM Digital warranty to be provided against Ink Fading, Peel off, Excessive Shirnkage. EFI Vutek or Durst or VIRTU Printer conformation of print supply is mandatory etc. all complete as per the direction of Engineer-in-charge

Providing & Fixing Name plate / Board 3mm Thk Clear Front Acrylic Sheet & 3mm Thk Clear Back Acrylic Sheet. Printed vinyl As per approved artwork of 3M Scotchcalgraphics IJ15-114 Glossy in UV printing on signage Mode on Hp Machine. SS Stud assembly with base & top of OD 35mm with internatl tapping for M12 bolt Wooden Screw with plastic bit etc. all complete as per the direction of Engineer-in-charge

Providing and fixing AC-4 Action Tesa or equivalent Lamination flooring all complete including wastage (only site measurement to be considered for payment.12mm Laminated floor colour and shade as approved by EIC etc. all complete as per the direction of Engineer-in-charge

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing & Fixing of Dorma handle with lock PLUS 8100/6500/6612 8MM 38-63MM SSS, 281a CE Sash lock backset 55mm, PCK 93 - 70MM PROFILE - SATIN NICKELor equivalent all complete as per direction of Engineer-in-charge.

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/120 no.and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion a) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing 12 mm thick panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. a) Marine plywood conforming to IS: 710

Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with : a) Decorative veneer facings of approved manufacture

Architectural consultancy charges for preparing and submitting the Architectural drawings/ design to carry out the decorative graphics printing items in this work. Cost to include downloading the higher resolution graphics good for printing from web and incorporating the same in Architectural design of the premises as per the direction of Engineer-in-charge. Agency to submit the design proposal based on sound Engineering / Architectural practice with modern concepts with various options / combinations suiting the interior of the premises / area as per the direction and satisfaction of Engineer-in-charge. The drawing to be approved by Engineer-in-charge. After approval of the proposal, agency to submit 5 (Five) sets of drawing for work execution etc. all complete as per the direction of Engineer-in-charge.