CERTAIN SANCTIONED SPECIAL REPAIR WORKS IN KHARIAN GRN AND CHATHA GRN AT MIRAN SAHIB UNDER GE JAMMU

Amount

B/R Portion: - Demolition of cinder concrete of any description and in any position and removing the rubbish from work site complete all as specified and as directed.

Demolition/ breaking of drain pipes (salt glazed ware, AC or reinforced concrete) set in cement mortar and taking out off trenches and removing the debris from the site all as specified of 150mm/ 200 mm dia pipe including demolition of cement concrete haunching etc complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of brick work/ stone/ boulder masonary, built in cement mortar including all quoins, arches, pillars, drains etc but excluding ashlars facings, dressed stone work and precast concrete articles complete all as specified and as directed.

Demolition of cement concrete of any description and in any position and removing the rubbish from work site complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Dismantling stone slabs laid dry and tiles of any description or thickness in floors, aprons etc. and rubbish off the premises complete all as specified and as directed.

Dismantling wrought iron or mild steel work as in wind tie, grill grating, cooler stand etc. complete all as specified and as directed.

Dismantling AC corrugated, semi corrugated sheets in roof covering complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc), or insulation boards/ slabs/ blankets, any thickness any type including cover fillets complete all as specified and as directed.

Dismantling timber scantling 40 Sqcm and over in section in any position as in unframed work complete all as specified and as directed.

Dismantling timber scantling in fillets, posts, rafters, purlins etc under 40 Sqcm in section complete all as specified and as directed.

Taking down cement plaster from brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Taking down chowkhats or frames not exceeding 1.5 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and as directed.

Taking down chowkhats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

Taking out of solid/ semi solid sludge from existing manholes of any size and any depth and burying the entire sludge/ sludge water into excavated pit of adequate size including excavation and covering with earth or disposing off into covered vehicles outside the peripherry of defence land to a distance exceeding 1 Km including taking off RCC/ iron man holes covers and refixing the same after clearing complete all as specified and as directed.

Taking down roof trusses, coupled rafters or trussed beams above 4 metres and upto 8 metres complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide not exceeding 1.5m in depth, for foundation, etc, or for shafts, wells cesspits, manholes, pier holes, etc not exceeding 10 Sqm on plan and not exceeding 1.5m in depth and getting out in hard/ dense soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified and as directed.

Removal of surplus excavated soil to a distance exceeding 250 m and not exceeding 500m and deposited where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

75mm thick cement concrete (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in floor/ plinth protection laid in suitable panels finished even and fair all as specified. 6mm joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 grade and three parts of sand (all by weight) complete all as specified and as directed.

PCC (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) as in surface channels complete all as specified and as directed.

PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) in foundation, filling and mass concrete complete all as specified and as directed.

PCC (1:3:6) type C-0 (using 12.5 mm graded crushed stone aggregate) as in back filling, bed block for hold fast, coping, benching on corner joints etc complete all as specified and as directed.

Providing 75 mm thick plain cement concrete (1:4:8) mix, type D-2 (using 40mm graded crushed stone aggregate) as sub-base floor complete all as specified and as directed.

25 mm thick PCC (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate), as in sub base/ floor complete all as specified and as directed.

PCC (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate) as in coping, benching on corner of joints, as in roof kerbs rounded or chamfered on edges etc complete all as specified and as directed.

Concrete bed to 150 mm bore pipe (1:4:8) in type D-2 (using 40mm graded crushed stone aggregate) including haunching against the sides of pipe complete all as specified and as directed.

RCC (nominal mix) (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

RCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) nominal mix as in lintel bend including necessary formwork to lintel band etc complete all as specified and as directed.

Formwork to flat soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished complete all as specified and as directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide complete all as specified and as directed.

Rendering 15 mm thick on fair faces mixing with water proofing compound as per manufacturer instruction (Water proofing compound paid for separately) of brick work or concrete surfaces in cement mortar (1:4) finished fair and even without using extra cement complete all specified. Note-: WPC shall be measured and paid separately under respective item.

Rendering 10 mm thick on faces other than fair of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 5 mm thick on ceiling or concrete surfaces in cement mortar (1:3) finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 20mm thick in cement mortar (1:4) on concrete surface such as chajjas, upward fascias, roof surfaces and similar items including two or more dubbing coat, surface finished even and fair without using extra cement including mixing of liquid waterproofing compound (LWPC shall be measured and will be paid separately) upto height of four storeyed building with all necessary formwork, scaffolding, lifting arrangement for external surface upto 4 storey buildings) complete all as specified and as directed.

Brick work with sub class 'B' old size brick straight or curved on plan exceeding 6 mtr mean radius built in cement mortar (1:6) complete all as specified and as directed.

Brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall in cement mortar (1:4) complete all as specified and as directed.

Pressed steel frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate and one shop coat of primer etc complete and fixed all as specified and as directed.

Pressed steel frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate and one shop coat of primer etc complete and fixed all as specified and as directed.

35 mm thick second class hard wood glazed and skelton shutters sizes of members as specified in SSR (Part-I) clause 8.24 (a), open rebated and prepared to receive glass or gauge (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass or gauge etc complete all as specified and as directed.

30mm thick flush shutters, solid core construction, with particle board core and both sides is covered with 2mm thick wooden pattern decorative face edge lipping/ frame to match and 0.9 mm thick decorative sunmica type 1, or surface finish, colour and pattern fixed with approved adhesive on both faces/ surface complete all as specified and as directed.

Factory made solid PVC moulded door frame of size 50 x 100mm with wood free EPS and 2mm thick moulded PVC sheet all around supplying and fixing in wall at site as per manufacturer's specification complete all as specified and as directed.

Factory made solid PVC moulded door shutter with wood free EPS, 28 to 30mm thick (stiles) with 2, 4, or 6 raised panel design with 2mm thick moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and drawing complete all as specified and as directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows and other frames/ chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed stainless steel screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) and 1100 N (Edge), minimum compressive strength of 58 N/mm², modules of elasticity 900 N/mm² and resistance to spread of flame of Class 'A' category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with mild steel hold fast/lugs/stainless steel dash fasteners of required dia and length complete as per directions of Engineer-in-Charge. (Mild steel hold fast/ lugs/ stainless steel dash fasteners shall be paid for separately). Note: -WPC solid door/ window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

18 mm thick factory made 100% solid WPC flush shutter (for cupboard and vanity etc) made from co-extruded three layer rigid foam sheet (single extruded) with 0.8 to 1 mm thick outer layer having density not less than 1400 kg/cum and density of central core not less than 600 kg/cum manufacturer by an ISO 9001/2015 certified company complete all as specified and as directed.

Supply and fixing in repair 18 mm thick factory made 100% solid WPC flush shutter (for cupboard and vanity etc) made from co-extruded three layer rigid foam sheet (single extruded) with 0.8 to 1 mm thick outer layer having density not less than 1400 kg/cum and density of central core not less than 600 kg/cum manufacturer by an ISO 9001/2015 certified company complete all as specified and as directed.

Supply and fixing in repair Box type steel windows/ Ventilator (factory made) outer frame made out ERW tube 'P' section 65 x 45 x 25 mm and shutter of ERW tube 'P' section 50mm x 35mm x 20mm openable (double shutter) with glazed shutter on external side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 nos on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler/ AC window complete all as specified and shown on drawings No CEPZTD-324/07 Sh 1/3 to 3/3 and as directed. Notes: - The quoted rates shall also include: - (i) One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks/ concrete surface. (ii) 4 nos MS steel lugs made of 20 x 5 mm Iron flat 200 mm long. (iii) 10 mm Sq Bar grill/ guard bar design as per drawing. (iv) PCC block for embedding lugs. (v) Two coats of synthetic enamel paint. (vi) Galvanised mild steel wire cloth 0.56 mm nominal dia or wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and as directed.

Supply and fixing in repair Stainless steel kitchen plate rack made out of not less than 0.63mm thick stainless steel sheet of size 750mm x 600mm x 250mm of approved pattern complete all as specified and as directed.

Supply and fixing in repair sinks with drainage board made of stainless steel 1 mm thick in kitchen with plugs, washers and waste coupling, waste pipe, including bedding in cement mortar on wall including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460 mm, bowl size 410mm x 330mm x 160 mm complete all as specified and as directed.

Suspended false ceiling system using 'E' grid suspended ceiling grid system. The size of grid shall be 600 x 600mm with GI frame work, main runner 39 x 24mm, cross tee 29 x 24mm and wall angle 22.2 x 22.2mm using 4mm thick high pressure stream cured non primered classic/ designer variant E-Board ISI Marked IS No 14862-2000. Fibre cement 'E' board to be placed in the gird of 'E' grid suspended ceiling grid system duly suspended by 4mm dia GI bar hangers from the purlins of the roof with butterfly clips complete all as specified and as directed.

8mm thick single layered HDHMR board one side white balanced and other exterior side with 0.9 mm thick decorative sunmica type 1 coloured textured finish board density more than 850 Kg/ cum smooth finished fixed in cupboard and jointed together with necessary adhesive complete all as per directions by Engineer-in-Charge, manufacturer’s specification complete all as specified and as directed.

Supply and fixing in repair 18mm thick single layered HDHMR board one side white balanced and other exterior side with 0.9 mm thick decorative sunmica type 1 coloured textured finish board density more than 850 Kg/ cum smooth finished fixed in cupboard and jointed together with necessary adhesive complete all as per directions by Engineer-in-Charge, manufacturer’s specification complete all as specified and as directed.

Supply and fixing in repair Curtain rod of stainless steel 20mm dia and side capes fixed in position by drilling holes in walls and fixed the brackets with rawl plugs and steel screws complete all as specified and as directed by Engineer-in-Charge.

Galvanized mild steel wire clothes power woven 0.56mm nominal dia of wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanized wire staples complete all as specified and as directed.

3mm thick sheet glass, ordinary quality glazing with oil putty/ beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Description all as per Ser item No. 59.00 here-in-before but figured glass, pin head type complete all as specified and as directed.

300 mm long stainless steel 304 grade sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding door bolt of extruded section complete with fasteners complete all as specified and as directed.

200mm long stainless steel barrel tower bolt (premium quality) of 8mm dia bolt of extruded section ISI marked complete with fasteners all as specified and as directed.

150mm long stainless steel barrel tower bolt (premium quality) of extruded section ISI marked complete with fasteners all as specified and as directed.

Stainless steel handle 200 mm (premium quality) fixed to cupboard complete all as specified and as directed.

Stainless steel handle 150 mm (premium quality) fixed to cupboard complete all as specified and as directed.

Floor door stopper of stainless steel 304 grade alloy body and tongue 140 mm anodised with hard drawn steel spring fixed in floor complete all as specified and as directed.

Stainless steel 304 grade butt hinges 100 mm medium weight cold rolled complete all as specified and as directed. Makes: - Dorset or equivalent in makes as specified in Group - I of Appx 'F'.

Mild steel enamelled helical door spring 150 mm, (ISI Marked) size including roller and roller plate, fixed to wooden/ steel frames by any means as required complete all as specified and as directed.

75 mm size butt hinges medium weight cold rolled stainless steel complete all as specified and as directed.

Modular auto concealed soft closed hinges 35mm, 160 degree size fixed to cupboard complete all as specified and as directed. Makes: - Dorset or equivalent in makes as specified in Group - I of Appx 'F'.

304 grade stainless steel handle 100mm fixed to cupboard complete all as specified and as directed.

Magnet catcher 50 mm size for kitchen cupboard shutter complete all as specified and as directed.

Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment as in gusset plate, base plate etc complete all as specified and as directed.

Aluminium handles 'D' type anodised 150 mm long ISI marked complete all as specified and as directed.

Aluminium handles 'D' type anodised 125 mm long ISI marked complete all as specified and as directed.

Floor door stopper of aluminium alloy body and tongue 140 mm anodised with hard drawn steel spring fixed in floor complete all as specified and as directed.

300 mm long dia 12 mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

100 mm size butt hinges medium weight stainless steel cold rolled mild steel complete all as specified and as directed.

150 mm long aluminium anodised barrel tower bolt of extruded section ISI marked complete all as specified and as directed.

200 mm long aluminium anodised barrel tower bolt of extruded section ISI marked complete all as specified and as directed.

Supply and fixing in repair soap dish steel chromium plated 100 mm size complete all as specified and as directed.

Vitrified tiles any colour 10 mm thick (square/ rectangular) polished as in floor, area of each tile not exceeding 0.36 Sqm etc set and jointed over neat 5-6 mm thick approved polymer modified tile adhesive of appropriate grade as per manufacturer instruction and laid with 3-4mm spacer, spacer gaps to be filled with approved epoxy grout including 15mm thick screed bed in CM (1:4) complete all as specified and as directed.

Description all as per Ser item No 82.00 here-in-before but in vertical surfaces fixed with 3-4 mm spacer set and jointed over neat 5-6 mm thick approved tile adhesive polymer modified tile adhesive of appropriate grade as per manufacturer's instruction and provided with 3-4mm spacer, spacer gaps to be filled with approved epoxy grout including 10mm thick CM (1:4) plaster complete all as specified and as directed.

Non skid ceramic coloured tiles 7 to 8 mm thick, edgeless, area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc set and fixed with approved tile adhesive polymer modified tile adhesive of appropriate grade as per manufacturer's instruction and provided with 3-4mm spacer, spacer gaps to be filled with approved epoxy grout including 15mm thick screed bed in CM (1:4) complete all as specified and as directed.

Description all as per Ser item No 84.00 here-in-before but as in vertical surface, skirting over and fixed with 3-4 mm spacer set and jointed over neat 5-6 mm thick approved tile adhesive polymer modified tile adhesive of appropriate grade as per manufacturer's instruction and provided with 3-4mm spacer, spacer gaps to be filled with approved epoxy grout including 10mm thick CM (1:4) plaster complete all as specified and as directed.

Non skid tiles coloured exceeding 0.06 Sqm and not exceeding 0.11 Sqm, 6-7mm thick of any colour pattern and 1st quality as approved by GE in floor set and fixed with 3-4 mm spacer set and jointed over neat 5-6 mm thick polymer modified tile adhesive of appropriate grade as per manufacturer's instruction and provided with 3-4mm spacer, spacer gaps to be filled with approved epoxy grout including 15mm thick screed bed in CM (1:4) complete all as specified and as directed.

Ist quality coloured digital glossy wall tiles of size 300 x 600 x 7 mm thick as on vertical surfaces such as skirting/dado etc fixed with 3-4 mm spacer set and jointed over neat 5-6 mm thick polymer modified tile adhesive of appropriate grade as per manufacturer's instruction and provided with 3-4mm spacer, spacer gaps to be filled with approved epoxy grout including 10mm thick CM (1:4) plaster complete all as specified and as directed.

Coloured glazed ceramic tiles glossy finish of size 450 x 300 x 5-6mm thick in dado’s/ skirting etc (1st quality) set and fixed with 3-4 mm spacer set and jointed over neat 5-6 mm thick polymer modified tile adhesive of appropriate grade as per manufacturer's instruction and provided with 3-4mm spacer, spacer gaps to be filled with approved epoxy grout including 10mm thick CM (1:4) plaster complete all as specified and as directed.

Machine cut kota stone slab flooring 18-20mm thick as in floor to match the shade of the slab including 20 mm screed bed cement mortar (1:6) including rubbing polishing complete all as specified and as directed.

Machine cut kota stone slab flooring 18-20mm thick as in riser in step, skirting/ dado to match the shade of the slab including rubbing and polishing over and including 10mm rendering in cement mortar (1:4) complete all as specified and as directed.

Exterior grade full body vitrified tiles matt finished 400 x 400 x 12mm thick set jointed in neat cement slurry and pointed with grey cement and pigments to match the shade of tile pattern as approved in floors including 15mm thick screed in cement mortar (1:6) complete all as specified and as directed.

Description all as per Ser item No 91.00 here-in-before but in vertical surfaces above but as in skirting over and including 10 mm thick rendering cement mortar (1:4) complete all as specified and as directed.

Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster (1:4) (1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster (1 : ½ : 2) (1 cement : ½ coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and as directed.

60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design and pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness and size/ shape, made by table vibratory method using PU mould, laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

16 to 18mm granite (Jet black, Nero Absolute or as appoved by Engineer-in-Charge) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including taking down old complete all as specified and as directed.

Providing edge moulding to 18-20mm thick Granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and as directed.

Cement concrete tiles 25 cm x 25 cm x 20 mm thick machine pressed tile set and jointed in cement slurry and pointed in grey cement mixed with cresote oil including 15 mm thick bedding layer in cement mortar (1:4) complete all as specified and as directed.

Provision of roof treatment with elastrometric water proofing membrane all as given below: - (a) Taking down existing water proofing treatment and cleaning roof surface by washing and rubbing etc. and removing the material retrieved to a distance not exceeding 500 m where directed. (b) Material and labour for plastering 10mm thick in cement mortar (1:3) using 100% coarse sand on roof surface including water proofing compound as per manufacturer's instructions and as directed by Engineer-in-Charge. (c) Applying one coat of primer of acrylic reinforcement liquid elastometric water proofing membrane with UV resistant properties and solar reflective properties (3:1 water dilution) on prepared surface with roller and allowed to dry. (d) Supply and applying two coats of undiluted thick coat of acrylic reinforcement liquid applied elastometric water proofing membrane with UV resistant properties and solar reflective properties before first coat insert smart care roof tape corner/joints and allow it to dry then apply further second coat complete all as specified and as directed. Note: - Every coat time gap should be minimum 6 hrs and thickness of each coat 2-3mm.

Two components elastomeric acrylic polymer modified cementitious waterproofing coating, smart care Ultra Block K or approved equivalent having >220 % elongation as per ASTM D 2370, resisting 5 bars hydrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 3.5mm as per EN 1062. The coating food shall have food grade certified from laboratories like CFTRI. The mixing ratio of the coating shall be 2 Parts of powder and 1 part of liquid without any water addition in the mixing complete as per manufacturer's specification. Minimum consumption shall be 2 Kg/Sqm including application of bond coat application Mix APSC, repair polymer and cement in ratio (1:1) applying with brush 1 or 2 continuous coats of mix and ensure minimum consumption shall be 0.2 Kg/Sqm complete all as specified and as directed.

Taking down existing sunken treatment and cleaning sunken surface by washing and rubbing etc. and removing the material retrieved to a distance not exceeding 500 m where directed. Material and labour for providing water proofing treatment to sunken floors all as given below: - (a) Making fillet of size 25mm x 25mm at corner of slab and wall with polymer modified cementitious (PMC) mortar consisting of one part of tapecrete P-151, two parts of cement and 6 parts of fine sand by weight. (b) Sealing of joints of pipe with epoxy putty CICO POXY LC or epoxy mortar CICO POXY 2125. (c) Cleaning the concrete surface by brushing and watering and applying a coat of tapecrete P-151 Acrylic Polymer Modified cementitious slurry consisting of one part of TAPECRETE P-151 and two parts of cement by weight. The coating shall be carried out upto 300mm above FFL and shall be allowed to dry for 4-6 hours. (d) Appying a coat of TAPECRETE brush topping 1.5mm thick consisting of one part of TAPECRETE P-151, two parts of cement and two parts of silica sand by weight and cured to 2 days. (e) Applying 15mm thick plaster in cement mortar (1:4) mixed with CICO super @ 100ml per 50 Kg cement on treated surface. (f) Material and labour cement concrete (1:5:10) type E-2 as in filling of sunken floor. Note: - Ponding test should be performed for 48 hours as per direction of Engineer-in-Charge.

Supply only liquid water proofing compound complete all as specified and as directed.

Mild steel TMT bars 10 mm dia and over cut to length, bend to shape etc complete binding with and including mild steel annealed wire not less than 0.09 mm dia conforming TMT bars complete all as specified and as directed.

Description all as per Ser item No 102.00 here-in-before but 5 mm dia and over upto and including 10 mm dia in stirrups dia complete all as specified and as directed.

Mild steel framed works such as grills, framed guard bars, etc and similar work as in cooler stands etc. conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed.

Structural steel section work as in Roof trusses (framed), post, trussed, purlins, Rafter, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections or mild steel tube pipe) and Rolled steel section work as in main and cross beam, purlin, rafter, tubular poles including distance pieces, cleats etc Fe-410W (Gde E-250) quality including shop coat of primer complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPs as in roof covering fixed with self tapping screws or L-type or J-type or cranked hook bolts complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPs as in ridge of roof fixed with self tapping screws or L-type or J-type or cranked hook bolts complete all as specified and as directed.

Preparation of new surfaces of ceiling and applying three coats of white washing to ceiling complete all as specified and as directed.

Preparation of old plaster or painted surfaces of ceiling and applying two coats of white wash complete all as specified and as directed.

Preparation of new surface and applying two coats of oil bound distemper new plaster surface over 1 mm thick putty complete all as specified and as directed.

Complete removal of existing surface and preparation of old surface and applying two coats of oil bound distemper over 1 mm thick putty complete all as specified and as directed.

Preparation of new surface and applying two coats of exterior emulsion/ weather proof paint over a coat of primer over and including 1mm thick putty on plastered surface complete all as specified and as directed.

Complete removal of existing surface and preparation of old surface and applying two coats of exterior emulsion/ weather proof paint over a coat of primer over and including 1 mm thick putty on plastered surface complete all as specified and as directed.

Preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

Preparing surface of new steel material of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Preparing old surface of steel material of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

GI spout 25mm dia light grade, fixed to walls complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair Chromium plated brass bib taps with wall flange 15mm fancy type chromium plated cast copper alloy with quarter turn handle and wall flange complete all as specified and as directed. Makes: - JAQUAR/ HINDWARE/ PARRYWARE/ equivalent in makes as specified in Group - 1 of Appx 'F'.

Supply and fixing in repair 15mm bore chromium plated central hole single lever basin mixer for WHB mixer without popup waste system with 450mm long braided hoses complete all as specified and as directed. Makes: - JAQUAR/ HINDWARE/ PARRYWARE/ equivalent in makes as specified in Group - 1 of Appx 'F'.

Supply and fixing in repair Single lever Wall mixer 3 in 1 system with provision of overhead shower complete with 115mm long bend pipe on upper side connecting legs and wall flanges (without overhead shower) including all fittings and fixed complete all as specified and as directed. Makes: - JAQUAR/ HINDWARE (ELEMENT)/ PARRYWARE/ equivalent in makes as specified in Group - 1 of Appx 'F'.

Supply and fixing in repair Chromium plated brass stop/ angle valves 15mm bore fancy type chromium plated with quarter turn handle and wall flange complete all as specified and as directed. Makes: - JAQUAR/ HINDWARE (CERA)/ PARRYWARE/ equivalent in makes as specified in Group - 1 of Appx 'F'.

Supply and fixing in repair Overhead shower 200 x 200mm square shape single flow (ABS body chrome plated with grey face plate) with rubit cleaning system including shower arm 450mm long including all fittings and fixed complete all as specified and as directed. Makes: - JAQUAR/ HINDWARE/ PARRYWARE/ equivalent in makes as specified in Group - 1 of Appx 'F'.

Supply and fixing in repair Fancy type brass chromium plated towel ring round with round flange including necessary fittings complete all as specified and as directed. Makes: - JAQUAR/ HINDWARE/ PARRYWARE/ equivalent in makes as specified in Group - 1 of Appx 'F'.

Supply and fixing in repair Fancy type brass chromium plated towel rack 600mm long with lower hangers complete all as specified and as directed. Makes: - JAQUAR/ HINDWARE/ PARRYWARE/ equivalent in makes as specified in Group - 1 of Appx 'F'.

Supply and fixing in repair Vitreous china water closet pedestal pattern cascade type with inbuilt flushing cistern and seat cover with complete fittings all as specified and as directed. Makes: - JAQUAR (LYRIC)/ HINDWARE (SPLENDOR/ PARRYWARE (OMEGA)/ equivalent in makes as specified in Group - 1 of Appx 'F'.

Supply and fixing in repair Stop cock, chromium plated fancy type screwed down high pressure, with crutch of butterfly handle, screwed both ends for iron pipe of size 15mm dia bore complete all as specified and as directed. Makes: - JAQUAR (FUSION)/ HINDWARE (Cora)/ PARRYWARE (CLARET)/ equivalent in makes as specified in Group - 1 of Appx 'F'.

Supply and fixing in repair 15mm bore chromium plated sink mixer for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed. Makes: - JAQUAR (FLORENTINE)/ Hindware/ PARRYWARE/ equivalent in makes as specified in Group - 1 of Appx 'F'.

Supply and fixing in repair Two way cock/ two way angle cock with wall flange matt chrome finish complete all as specified and as directed. Makes: - Prima or equivalent in makes as specified in Group - 1 of Appx 'F'.

1000 litre capacity Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) three layers hoisted and fixed in position and including dismantling of water tank complete all as specified and as directed.

Supply and fixing in repair PVC connection 15mm bore and for 600 mm long with brass or PVC nuts and PVC washer complete all as specified and as directed. Makes: - Prima or equivalent in makes as specified in Group - 1 of Appx 'F'.

Supply and fixing in repair PVC waste pipe 32mm bore complete all as specified and as directed. Makes: - Prima or equivalent in makes as specified in Group - 1 of Appx 'F'.

Supply and fixing in repair Fancy type brass chromium plated toilet paper holder with flap including all fittings and fixed complete all as specified and as directed. Makes: - JAQUAR/ HINDWARE/ PARRYWARE/ equivalent in makes as specified in Group - 1 of Appx 'F'.

Supply and fixing in repair Chromium plated 125mm soap dish in postion complete all as specified and as directed by Engineer-in-Charge. Makes: - Prima or equivalent in makes as specified in Group - 1 of Appx 'F'.

Supply and fixing in repair Cabinet mirror plastic body for toilet of size 450 x 600mm with 4mm thick looking mirror complete all as specified and as directed. Makes: - Prima or equivalent in makes as specified in Group - 1 of Appx 'F'.

15 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and as directed.

20 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and as directed.

Supply and fixing in repair 125 mm chromium plated stainless steel grating with or without waste hole complete all as specified and as directed.

Supply and fixing in repair Health faucet (hand shower) with 1 mtr flexible tube with hot and cold water supply wall hook, bracket etc complete set of superior quality complete all as specified and as directed. Makes: - JAQUAR/ PARRYWARE/ HINDWARE/ equivalent in Group - 1 of Appx 'F'.

Supply and fixing in repair Vitreous china squatting pan 'Orissa' pattern, size 580 x 440 mm white, with integral foot rest and 'P' or 'S' trap and connection to flushing pipe, anti-syphonage pipe complete including provision of cement concrete bedding complete all specified in SSR part - I complete all as specified and as directed.

Supply and fixing in repair Vitreous china corner wash basin, white, flat back, size 400 x 380 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, waste coupling cutting, waste pipe for and pinning in ends of brackets or erecting stand complete all as specified and as directed.

Supply and fixing in repair Vitreous chinaware wash hand basin white, flat back of size 550 x 400 mm excluding tap but including brackets fixing to wall and two Nos 10mm dia 100mm long nut and bolt over brackets and chromium plated waste coupling complete all as specified and as directed. Makes: - Cera (Ist Quality)/ Hindware (Ist Quality)/ Parryware (Super fine)/ equivalent in makes as specified in Group - 1 of Appx 'F'.

Supply and fixing in repair PVC valveless, symphonic action type, flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

Supply and fixing in repair 15 mm bore bib taps long nose/ long body, cast copper alloy chromium plated fancy type with capstan head handle screwed down, screwed for brass, weight not less than 450 gms ferrule and fixed complete all as specified and as directed.

Supply and fixing in repairs bib taps, fancy type chromium plated (Short body) with crutch or butterfly handle,screwed down, screwed for iron pipe of 15mm dia bore including necessary fittings complete all as specified and as directed.

Supply and fixing in repair Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed of 20 mm bore (minimum weight - 210 grams) complete all as specified and as directed.

Supply and fixing in repair 15 mm bore angle valves, cast copper alloy chromium plated fancy type, half turn, screwed down, high pressure, with crutch or butterfly handle, weight not less than 450 gms screwed both ends for iron pipe or for unions complete all as specified and as directed.

Supply and fixing in repair 15 mm bore sawn neck pillar cock cast copper alloy, chromium plated with angular knob fixed to 15mm dia mild steel pipe complete with all fittings complete all as specified and as directed.

Supply and fixing in repair 20 mm dia Gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

Supply and fixing in repair Mild steel peg set of six power coated as approved by GE complete all as specified and as directed.

Supply and fixing in repair Brass chromium plated towel rail 20 mm dia 'D' type 60 cm long between flanges complete all as specified and as directed.

Supply and fixing in repair Glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket, guard and railing 60cm long complete all as specified and as directed.

150 mm thick reinforced concrete pipes class NP-2 laid and jointed complete with collars as in trenches complete all as specified and as directed.

Perforated precast 100 mm thick M-30 RCC manhole cover, minimum 800 to 900 mm dia/ side of clear opening circular/ rectangular and including collar frame set and including lifting hook (02 Nos) complete fixed in position over existing manholes complete as specified and as directed by Engineer-in-Charge.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement complete all as specified and as directed.

75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, bends, Tees complete fixed to walls at any height complete all as specified and as directed.

75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, bends, Tees complete laid in trenches or in floors complete all as specified and as directed.

110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, bends, Tees complete fixed to walls at any height complete all as specified and as directed.

110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, bends, Tees complete laid in trenches or in floors complete all as specified and as directed.

PVC (SWR) bends 110 mm radius complete all as specified and as directed.

110 mm PVC (SWR) junction single (T) equal/ Unequal complete all as specified and as directed.

PVC (SWR) bends/ shoes any radius of 75 mm dia complete all as specified and as directed.

PVC (SWR) bends any radius provided with access door of 110mm dia complete all as specified and as directed.

Description all as per Ser item No 163.00 here-in-before but 75 mm dia complete all as specified and as directed.

PVC (SWR) vent cowl of radius of 75 mm dia complete all as specified and as directed.

Supply and fixing in repair 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 complete all as specified and as directed.

Supply and fixing in repair Stack clamps out of 50mm x 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stay to walls or roof for 75 mm bore pipe complete all as specified and as directed.

Supply and fixing in repair Stack clamps out of 50mm x 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stay to walls or roof for 100mm bore pipe complete all as specified and as directed.

Supply and fixing in repair 15mm dia chromium plated pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

Supply and fixing in repair Shower rose brass chromium plated with swivel joint of size 125 mm cast copper alloy chromium plated fancy type with chromium plated neck 9" long made to shape, weight not less than 350 gms complete all as specified and as directed.

E/M Portion: - Taking down old unserviceable copper/ aluminium point wiring concealed/ batten (light, fan, socket or power) complete including fixtures and fittings such as switches, sockets, ceiling roses, bell push, bell electric, lamp holder, bulk head fitting, pendants, regulators, sockets, light fitting and any type switch board PVC/ iron, round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

Taking down fan, ceiling cable end, dismantling blades and removing fan and blades to store and Hanging to same location to ceiling fan (M.D. supply) and connecting up including provision of cable from ceiling rose after completion of point wiring complete all as specified and as directed.

Taking down Exhaust fan from wall and ceiling cable end, keeping it in store and fixing it to same location and connecting up including provision of cable from ceiling rose after completion of point wiring complete all as specified and as directed.

Taking down geyser and keeping it in store and fixing it to same location and connecting up with cable after completion of point wiring complete all as specified and as directed.

Sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 2 run 6 Sqmm for phase and neutral including medium grade PVC conduit 25 mm dia concealed, with cutting chases and making good disturbed surface complete and one run of 6.0 Sqmm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn through the same rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/ neutral and one run of cable for earth will be measured and paid as one unit length including taking down old wiring complete all as specified and as directed. Notes: - (i) Wiring shall be done in proper colour coding. (ii) Rates are inclusive of cutting/ chases with suitable PCC works and making good to disturbed surfaces.

Point wiring for one light/ fan point controlled by one 5 Amp switch with 1.5 Sqmm two single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including medium grade PVC conduit 25 mm dia concealed, with cutting chases and making good disturbed surface complete including continuous earth wire of size 1.5 Sqmm copper conductor multistranded FRLS, PVC insulated (unsheathed) drawn same conduit with modular CI/ pressed steel sunken terminal boxes of required size with modular cover plate with frame for mounting switches, sockets, fan regulators etc complete all as specified and as directed. Notes: - (i) Wiring shall be done in proper colour coding. (ii) Rates are inclusive of cutting/ chases with suitable PCC works and making good to disturbed surfaces.

Point wiring for one light point controlled by Two 2 way switch with 1.5 Sqmm two single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including medium grade PVC conduit 25 mm dia concealed, with cutting chases and making good disturbed surface complete including continuous earth wire of size 1.5 Sqmm copper conductor multistranded FRLS, PVC insulated (unsheathed) drawn into same concealed PVC rigid conduit and with modular CI/ pressed steel sunken terminal boxes of required size with modular cover plate with frame for mounting switches, sockets, fan regulators etc complete all as specified and as directed. Notes: - (i) Wiring shall be done in proper colour coding. (ii) Rates are inclusive of cutting/ chases with suitable PCC works and making good to disturbed surfaces.

Description all as per Ser item No 176.00 here-in-before but for multi 5 pin 5 amp socket outlet on same board ISI marked complete all as specified and as directed.

Description all as per Ser item No 176.00 here-in-before but for multi 5 pin socket outlet 5 amp socket on independent board ISI marked complete all as specified and as directed.

Description all as per Ser item No 176.00 here-in-before but for one bell point controlled by one push button on the same board with other switches or independent with cable 1.5 Sqmm size complete all as specified and as directed.

Description all as per Ser item No 176.00 here-in-before but for multi 6 pin 15 Amp socket outlet independent controlled by 15 Amp switch with 2.5 Sqmm copper conductor two single core multistranded cable PVC insulated FRLS and unsheathed cable in and including PVC rigid concealed conduit 25 mm dia and unsheathed copper conductor multistranded cable 2.5 Sqmm as earth wire FRLS PVC insulated in green color complete all as specified and as directed by Engineer-in-Charge.

Modular Socket, 6A - 5 pin combined 2 module, 240 volts ISI marked complete all as specified and as directed.

Modular switch 1 module 6A, 1 module, 240 volts ISI marked complete all as specified and as directed.

Modular switch 2 way 6A, 1 module complete all as specified and as directed by Engineer-in-Charge.

Modular bell push 6A, 1 module, 240 volts ISI marked complete all as specified and as directed.

Ceiling rose, 2/3 Pin/ PVC/ polycarbonate isolated body ISI marked complete all as specified and as directed.

Modular switch 1 way 16 A, 1 module, 240 volts ISI marked complete all as specified and as directed.

Modular Socket 6A/16A - 6 pin combined 2 module, 240 volts ISI marked complete all as specified and as directed.

Calling bell Ding Dong AC 230 Volts, single pole ISI marked complete all as specified and as directed.

Modular lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

Self ballast LED retrofit lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and as directed.

LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

LED lights fitting 1 x 20W, 220 V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.9, 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Distribution Board TP&N 4 way double door suitable for TPN 4 pole 63 Amp 10 KA it should be IP-43 protected with copper bus bars, neutral links, Earthing bar complete all as specified and as directed.

Distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 12 way 240 volts double door complete all as specified and as directed by Engineer-in-Charge. Note: - Distribution board and MCBs should be of same make.

MCB SPN 40 to 63 Amp rating 240V, 10 KA 'B' curve type, complete with connection, testing and commissioning complete all as specified and as directed.

MCB, 240V, 10 KA 'B' curve of single poles and current carrying capacity 6 to 32 Amp, complete with connection, testing and commissioning complete all as specified and as directed.

Earthing complete with galvanised mild steel earth plate electrode of size 600 x 600 x 6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC (1:2:4) type B-1 pre-cast RCC cover slab using reinforcement with suitable handle made of round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and as directed.

MCB, 415V 10 KA 'B' curve, TPN 4 Pole, of 63 Amps complete with connection, testing and commissioning complete all as specified and as directed.

Fan step regulator, 120 W - 2 module 240 volts ISI marked complete all as specified and as directed.

LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, GI bracket of suitable size and clamp or nut bolt and corrosion resistant including thermal management in multiple optics complete with IP-65/66 protection complete all as specified and as directed.

Disconnecting and taking out defective underground cable any size and any type from trenches, roof, pole, pipe, floor, wall etc complete all as specified and as directed.

XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 volts grade 35 Sqmm 3.5 core laid in trenches/ on poles/ road crossing or passing through existing/ new pipe under road crossing, clamping on wall etc complete all as specified and as directed.

XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 volts grade 16 Sqmm 4 core laid in trenches/ on poles/ road crossing or passing through existing/ new pipe under road crossing, clamping on wall etc complete all as specified and as directed.

XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 volts grade 16 Sqmm 2 core laid in LT Over Head Line LT Pole to SPN DBs included clamps, nut, bolts fitting fixture etc complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m deep and not exceeding 1.5m wide and getting out in soft/ loose soil for laying of cable and foundation of pole complete all as specified and as directed.

Sand cushioning with dry and clean over and under the cable for protection of cable, 18 cm sand laid before laying the cable and 5 cm sand after laying the cable and filling the sand in cable duct inside the sub station building complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layer not exceeding 25 cm complete all as specified and as directed.

Removing of excavated material not exceeding 50 m and depositing where directed at level not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified and as directed.

Sub class 'B' bricks (old size) for cable protection cover laid flat and dry in trenches over the cable prependicular to the direction of cable complete all as specified and as directed.

Distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and as directed by Engineer-in-Charge. Note: - Distribution board and MCBs should be of same make.

LED light fitting 10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Ceiling fans complete with blades, down rods, suitable for working on fan regulator and accessories, 230 V, 1200 mm sweep minimum air delivery 245 CFM with service value 6.00 BEE five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

PAKAYA BUILDERS AND DEVELOPERS PVT LTD (BID ID -3478453)

J P TECHNO (BID ID -3477798)

M/S Shesh Paul Gupta (BID ID -3484020)