Construction of building for School of Earth, Ocean and Atmospheric Sciences

Amount

Clearing jungle including up rooting of rank vegetation grass bush wood trees and sapling of girth upto 30 cm. measured at a height of 1 m above ground level & removal of rubbish upto a distance of 50 mt. outside the periphery of the area cleared. (if however, only grass is met with the area will be measured and paid for under item 4001).

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sq.m on plan) including disposal of excavated earth lead upto 50 m and lift upto 1.5m disposed earth to be leveled and neatly dressed including providing barricading, danger lighting guarding as directed in :

b) All types of Ordinary rock including all types of laterite rock, blasting prohibited

Earthwork in excavation by mechanical means ( hydraulic excavator/manual means in foundation trenches drain ( not exceeding 1.5 m in width or 10 sq.m on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50m.

b. All types of ordinary rock including all types of laterite rock, blasting prohibited.

Extra for additional depth of 1.5 m or part thereof in:

c) All types of laterite rocks and hard rocks

Refilling the foundation trenches plinth sides, foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50M and all lifts and disposal of surplus earth as directed by Engineer in charge

Supplying and filling in plinth under floors, trenches including watering ramming consolidating, dressing, complete.

b) Moorum

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Pre-cast cement concrete solid blocks masonry of compressive strength 70 kg / cm2 in cement mortar 1:4 (1 cement : 4 corase sand ) in partitionwalls size of blocks (30 x 20 x 10)

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1:4 ( 1cement : 4 coarse sand ) in foundation and basement

Pre-cast cement concrete solid block masonry of compressive strength 70 kg / cm2 in cement mortar 1:4 (1 cement : 4 corase sand ) in all sizes in superstructure from floor one level upto floor V level ( size of block 30x23x15)

Exposed decorative laterite masonry usingPatradevi stone of size as specified and laid asdirected by rchitect in cement mortar 1:4 (1cement : 4 coarse sand)

Providing and laying cement concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 graded granitic or basaltic stone aggregate 20mm nominal size ) excluding cost of centering, shuttering and finishing in :

a)all works up to plinth level

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in:

A) all works up to plinth level

Providing and laying cement concrete1:5:10 (1 cement: coarse sand: 10 graded stone aggregate 40 mm nominal size) all round S.W pipes including bed concrete 15 cm thick as per standard design.

b) 150 mm diameter S.W pipe

Providing & laying damp proof course 50 mmthick with cement concrete 1:2:4 (1 cement: 2coarse sand: 4 graded stone agg. 20 mm nominalsize).

Providing and laying in position machinebatched concrete (BMC), machine mixed anmachine vibrated design mix cement concrete ofspecified grade for reinforced cement concretework including pumping of concrete to the siteof laying but excluding the cost of centering ,shuttering, finishing and reinforcementincluding admixtures in recommendedproportions as per IS 9103 to accelerate, retardsetting of concrete, improve workability withoutimpairing the strength and durability as per thedirection of the Engineer-in-charge. M-30 gradeof reinforced cement conrete by using 420 kg ofcement per cu.m. of concrete. All works upto floor V level.

Providing and laying in position ready mixedconcrete (RMC) with usage of OrdinaryPortland Cement manufactured in fully automatic batching plant and transported to siteof work in transit mixer for a lead upto 10kmshaving continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C., from the transit mixer to the site of laying, excluding the cost of centering,shuttering, finishing and reinforcement including the cost of admixtures in recommended porportions as per IS : 9103 to accelerate/retard setting of concrete, improve workability without imparing strength and durability as per the directions of the engineerin- charge. All works upto floor V level

v)M-30grade of concrete

Extra for carriage of R.M.C. beyond the initial lead of 10 kms.Considering additional lead of 15 kms i.e. 47x15

Centering and shuttering including strutting , propping & removal of forms for

I) Foundations, Footings, Bases for columns

II)Vertical surfaces such as retaing walls, returnwalls, Partitions, walls (any thickness) includingattached Pilasters, Buttresses, Plinth and stringcourses, Fillets and the like

III) Columns , piers, pillars, abutments, posts and struts ( square, rectangle or polygon in plan )

iv) sides / soffits of beams, beam haunchings, cantilevers, girders, bressumers and lintels plinth beams not exceeding 1M in depth

XIII) Suspended floors , roof landings, shelves & their supports,chajjas

vi) Staircases ( except spiral staircases) excluding landing

xiv) Vertical or horizontal fins individually formingbox louvers or projected bands

Extra to be added for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and de centering at all levels, over a height of 3.5 m for every additional height of 1m or part thereof ( Plan area to be measured)suspended floors, roofs, landings, beams and balconies( plan area to be measured)

Providing corrosion resistant steel CRS-50 bars of (SAIL, TATA, VIZAG, JSW SteelLtd.)(Confirming to IS 1786 if 1985) for RCCwork including bending, binding & placing inposition in all the floors along with factory made precaste concrete cover blocks of specified s izeswhose compressive strengthis not less than thatof surrounding concrete in the structuralmember .

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer : Flamed finish granite stone slab.

a) Jet Black

Providing and fixing Granite stone slabs (mirrorpolished) 18mm thick in risers of steps, skirting,dado and pillars laid on cement paste andjointed with grey cement slurry mixed withpigment to match the shade of the slabs,including rubbing and polishing complete

a) Jet black

Providing and fixing Vitrified tiles in different sizes (thickness to be specified bymanufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps and dados, jointing with grey cement slurry @3.3 kg per sqm, including pointing/grouting in white cement mixed with pigment of matching shade complete

b) 600 x 600 mm - Light Shades

Providing and and laying vitrified unglazedorcelain tactile floor tiles in different sizes ofJohnson, Somany, Kajaria (thickness to bespecified by the manufacturer) and conformingto IS:15622 of approved make in colours andshades as specified laid on 20 mm thick cementmortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement andmatching pigment etc., complete

a 300 x 300 mm Design - Liner

b 300 x 300 mm Design - Buttons

Providing and fixing vitrified matt finished (600 X 600) and 10 mm thick tiles in floor , treads of steps, and landings with cement based high polymer modified quick -set tile adhesive( water based) conforming to IS-15477, using 5kg adhesive per sq.m of tile area, in average 3mm thickness (Johnson, somany ,kajaria).

Providing and fixing vitrified matt finished (600 X 600) and 10 mm thick tiles in floor, treads of steps, and landings on 25 mm thick cement mortar 1:3 and jointed with cement slurry complete(Johnson, somany ,kajaria).

Providing and fixing 1st quality ceramic glazed wall tiles (Johnson, Somany, Kajaria )conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade complete.

(C)Wall Ceramic Glazed Tiles : 300 x 600

Providing and fixing vitrified antiskid tiles (320 x 320) and 10mm thick tiles in floor, treads of steps, landings on 25 mm thick bed of cement mortar 1:3 and jointed with cement slurry complete

Rounding of edges of kotah /granite slab to semi circular slope

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqm

(a)Jet Black

Providing 25 mm thick cuddapah slabs machine cut and polished on either side in partitions including making necessary grooves in the wall and fixing with cement mortar, complete as directed by the engineer-in-charge

Kotah stone slab flooring over 20 mm (average)thick base laid over & jointed with grey cementslurry mixed with pigment to match the shade ofthe slab including rubbing & complete with baseof cement mortar 1:4 (1 cement : 4 coarse sand)

a) 20 mm thick.

Providing woodwork in frames of doors, windows, clerestory windows trusses & other frames wrought framed and fixed in position.

c) first class matti wood

Providing and fixing 38 mm thick panelledglazed or panelled and glazed shutters for doors,windows and clerestory window includinganodized aluminium butt hinges with necessaryscrews:

a) Second class Indian teak wood

Providing & fixing flush door shuttersdecoration type core of block board constructionwith frame of first class hard wood and wellmatched first class Indian teak ply veneeringwith vertical grains and cross bands and faceveneers on both faces of shutters.

b) 35mm thick including anodized aluminium butthinges with necessary screws:

Extra for providing vision panel not exceedin0.1 sq.m. in all types of flush doors (cost of glassexcluded)

a Rectangular or square Unit: SQ.M. door area

Single Colour Foam Core FRP (Fiber Reinforced Polymer) Door Shutter Manufacture, Supply and Installation (including accessories as mentioned below) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) door shutter of specified thickness as per options below by using tray system with seasoned hard wood, moisture less than 17%, wood styles for Top rail and lock rails. FRP (Fiber Reinforced Polymer) laminate made up of 450 grams per sq.mts (gsm) chop strand matt and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps) . The core of shutter will be filled as specified (Expanded Polystyrene Foam / Polyurethane Foam (EPS/PU) Foam). The shutter to be of single colour & water proof as well as mild acid / alkali resistant manufactured using RV TIFAC (R V Engineering College, Bangalore & Technology Information Forecasting & Assessment Council) technology in line with IS 13034 1990 test Standard in an ISO 9001 – 2015 certified factory.

Accessories:

i) S. S. Hinges 4” - 3 Nos

ii) S. S. Latch - 1 No

iii) Tower Bolt 5” - 2 Nos

iv) Handle 5” - 2 Nos

Shutter Thickness b) 35mm

Providing & fixing anodised aluminium sliding door bolt anodised transparent or dyed required colour and shade with bolts, nuts and screws etc. complete ( ISI mark, Heavy )

Providing and fixing anodized aluminium flat latch

Providing and fixing aluminium tower bolt (barrel type) anodised or dyed to required colour or shade with screws etc complete.

( ISI mark, Heavy )

Providing and fixing aluminium handle anodized or dyed to required colour or shade with screws etc. ( ISI mark, Round, Heavy)

Providing and fixing 150mm bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete

Providing and fixing first class Indian teak wood moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surfaces etc.

Providing and fixing brass hydraulic door closer of make Everest/ universal/ Godrej with necessary screws and fittings complete.

Providing flat iron hold fast 40 cm including fixing to frame with 10mm dia bolts , nuts and wooden plugs and embedded in cement concrete blocks 30 x 10 x 15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 stone aggregate 20 mm nominal size

b) 40 x3 mm flat iron hold fast, 15 cm long

Providing and fixing stainless steel (Grade 304)railing made of Hollow tubes, channels, platesetc.with hairline finish, including welding,grinding, buffing, polishing and makingcurvature (wherever required) and fitting thesame with necessary stainless steel nuts andbolts complete, i/c fixing the railing withnecessary accessories & stainless steel dashfasteners, stainless steel bolts etc., of requiredsize, on the top of the floor or the side of waistslab with suitable arrangement as per approvalof Engineer, ( for payment purpose only weightof stainless steel members shall be consideredexcluding fixing accessories such as nuts, bolts,fasteners etc.).

Providing and fixing in position S.S. hand rail inmain stair case, and landing as per approveddesign shown in the drawing including bendinghandrail pipe to proper shape in curves withspecials, etc. complete.

Providing and fixing M.S grill of required pattern in wooden frames of windows etc with M.S flats square or round bars with round headed bolts and nuts or by screws.

a) Plain grill

Providing and fixing Aluminium shutters (Jindal make), 40mm series double openable shutters as per design including transportation, scaffolding and handling etc, complete. Windows with openable double shutters with outer frame 39 mm x 40 mm and shutters 54 mm x 40 mm with aluminium cleating system on SS 304 friction stay hinges, fixed mullion, single point locking, fixing screws of HILTI make with GP silicon.

Providing and fixing 8mm Aluminium grill for AC duct with aluminium back up frame section of 63 x38 mm as per grill design with gap of 80mm including powder coating, etc.complete

Providing and fixing Aluminium shutters (Jindal make), 27mm-Domal series windows aluminium cleating system as per design including transportation, scaffolding and handling etc, complete. Windows with three track ,three sliding shutters with outer frame 100.6mm x 45mm and shutters 65mm x 27mm kinlong touch lock, epdm gasket, all screws of S.S 304 grade fixing screws of HILTI make complete with G.P Silicon ( excluding GST)

(i) 5mm clear annealed glass of St. Gobain/AIS.

Extra for powder coating with pure polyester powder of shade of required colour on the aluminium section

12mm cement plaster 1:4 ( 1 cement : 4 coarse sand )

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1;5 ( 1cement : 5 coarse sand ) and top layer 6 mm thick with cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with sponge

6mm cement plaster to ceiling 1:3 ( 1cement : 3 fine sand)

Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete.

Extra for providing and mixing water proofing material proportion recommended by the manufacturers

a) 12mm cement plaster 1:3 ( 1cement: 3 sand)

Applying priming coat with ready mixed primer of approved brand and manufacture on WOOD WORK complete

Painting two or more coats (excluding priming coat ) with superior quality ready mixed paint(satin finish) for WOOD WORK of approved brand & manufacture in all shades on NEW WORK to give an even shade

Painting three or more coats with acrylic exterior paint of approved brand and manufacture ( such as weather shield, Apex) including applying one coat of cement primer and one coat of surface treatment etc. complete

Applying one coat of cement primer of approved brand and manufacture on wall surface.

Wall painting ( two or more coats) with plastic emulsion paint of approved brand and manufacture including a priming coat on NEW WORK to give an even shade

Applying one or more coat of Zinc epoxy primer on steel work of approved brand & Manufacture (Asian/berger) on New work to give an even shade

Painting two or more coats (excluding priming coat) of Epoxy Paint for Steel Work of approved brand (Asian/Berger) on New work to give an even shade.

Providing waterproofing treatment over the RCC roof terraces by speading cement slurry over the RCC slab and laying of 10 cms, average laterite stone ballast coba with the necessary gradient for easy flow of rain water and the coba in covered terraces and balconies with damp proof of jointless water proofing plaster of mix 1:3 (1 cement :3 fine sand), finished smooth with wooden trowel with false markings of 30cm square.The vertical surface of the adjoining walls are to be treated up to a height of 30 cms including rounding of junction(the rate includes for complete items including labour and materials and including bcost of initial treatment of roof slab as follows. The injunction of damp proof or equivalent compound with cement solution will be given as and when necessary for filling honey combs ,cracks etc in the RCC slabs)NOTE:cement consumption 25 Kg/ sq.m

Providing and filling in the sunken slabs with C.M 1:4 . Broken laterite soling stones to be laid in layers with mortar and top layer of I.P.S finish (1:2:3) over brickbat coba filling etc complete in all floors.

Neat cement punning

Providing anti – termite treatment to buildingsconforming to I.S.S. 6113 part II 1971 (revised)including adopting precautions for healthhazards and safety measures as required therein with the cost of all materials, chemicals, plants,equipments required for the treatment and furnishing a guarantee for a minimum period of 10 years from the date of completion including eradicating any infestation of termite free of cost during the guaranty period complete. (Thepayment will be made on plinth of the building.

a)Pre-construction

Providing & Fixing of Aluminium Lay-in Perforated Tile Ceiling on 24 /14 mm ‘T’ Framework of module 600mm x 600mm. Tiles of size 575mm X 575mm / 584mm x584mm made out of 0.6mm thick Aluminium. Perforation of the tiles shall be 2.5mm dia 5.5mm c/c. The Tile shall be manufactured on advanced equipment, which includes several levelling. The tile end shall be raised upward by 38mm and bend outward to lay the tile in framework. The Tile shall be Polyester based, powder coated in white colour. Grid system for fixing ceiling tiles shall comprise of Tees. The 24 /14 mm main tee runners shall be suspended at an interval of 1200mm centre to centre. The 24 /14 mm cross tee runner shall be suspended at 600mm centre to centre and further supported with 24 /14 mm cross tee at 600mm centre to centre with interlocking arrangements to form grid of 600mm x 600mm. The main tee shall be supported by means of 4mm G.I. rod from slab/roof. The suspension shall be provided at 1200 to 1500mm centre to centre. Tee framework would be made of GI and Powder coated. Acoustic Felt: Non-woven felt made of glass-reinforced fibre glued over the perforation for sound absorption.

Gypliner or equivalent ceiling which includesproviding & fixing G.I. HG angle of sie 0.55 mm thick having two equal flanges of 25 mm each screw fixed to brick wall / partition with the help of nylon sleeves & screws at 610 mm c/c. Then suspending chan 12.5 mm tapered edge Gypboard (confirming to IS:2095-1982) is then fixed to channel section with 25 mm drywall screws at 230 mm centre. Screw fixing is done mechanically with drill machine and suitable attachment. Finally square and tapered edges joints of the boards are jointed and finished so asto have flush look which includes filling finishingwith jointing compound, joint paper tape and two coats of Drywall top coat suitable for Gypboard (as per recomended practices of India Gypsum Limited).

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. of make ASTRAL/ASHIRWAD

a)15 mm dia nominal outer dia pipes.

b)20 mm dia nominal outer dia pipes.

c)25 mm dia nominal outer dia pipes.

d)32 mm dia nominal outer dia pipes.

Providing and fixing ASTM UPVC pipe,conforming to ASTM 2467 with ISO 14001,including all UPVC plain & brass threadedfittings, including fixing the pipe with clamps at1.00 m spacing. This includes jointing of pipes &fittings with one step UPVC solvent cement andtesting of joints complete as per direction ofEngineer. Internal work - Exposed on wall.

I SCH-80(blue)/(white)

a)20mm outer dia

b) 25mm outer dia.

c) 32mm outer dia.

d) 40mm outer dia.

e) 50mm outer dia.

Providing and fixing ASTM UPVC pipe,conforming to ASTM 2467 with ISO 14001,including all UPVC plain & brass threadedfittings, including jointing of pipes & fittings withone step UPVC solvent cement, trenching ,refilling & testing of joints complete as perdirection of Engineer. External work.

I SCH-80(blue)/(white)

c 32mm outer dia.

d 40mm outer dia.

e 50mm outer dia.

Providing and fixing rigid PVC S.W.R. (soil, waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed:

a) 110 mm dia

b) 75 mm dia

Providing and fixing single Tee of rigid PVC(approved make ) for S.W.R. pipes includinglubricating etc complete, with door :

a) 110 mm dia

b) 75mm dia

Providing and fixing single “Y”of rigid PVC S.W.R pipes (soil, waste & rain water drainage pipes of approved make including lubricant etc. complete ,with door

a) 110 mm dia

b) 75 mm dia

Providing and fixing rigid PVC bend ( approved make) for SWR pipes including lubricating etc complete, with door

a)110 mm dia

b) 75mm dia

Providing and fixing double “Y”of rigid PVC S.W.R pipes (soil, waste & rain water drainage pipes of approved make including lubricant etc. complete ,with door

a) 110 mm dia

b) 75 mm dia

Providing and fixing R.P.V.C vent cowl

a) 110 mm dia

Providing and fixing square-mouth S.W. gully trap grade ‘A’ complete with c.i. grating brick masonry chamber and water tight C.I. cover with frame of 300 x 300 mm size (inside the weight of cover to be not less than 4.53 kg). And frame to be not less than 2.72 kg as per standard design :

b) 150 x 100 mm size –P or S type

Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand) RCC top slab with 1:2:4 mix (1 cement : 2 Coarse sand : 4 graded stone aggregate 20mm nominal size foundation concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 40mm nominal size )inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1cement :2 coarse sand :4 graded stone aggregate 20mm nominal size ) neatly finished complete as per standard design.

d) Inside size 60 x 60 cm and 60cm deep including C.I cover with frame (light duty ) 455 x610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 Kg)

b) Inside size 90 x 80 cm and 60 cm deep including C.I cover with frame ( light duty ) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 kg ( weight of cover 23 kg)

Extra for depth for manholes : a) size 90 x 80 cm

Providing and fixing NICKEL chrome platedcopper alloy Fancy BIB Cock Short Body Jaquarmake or equivalent. Confirming to IS 8931;1993

a)15mm nominal bore

Providing and fixing Nickel chrome plated copper alloy BIB cock (long body) JAQUAR make with wall flange or ARK SUPREME confirming to IS 8931; 1993

a) 15 mm nominal bore

Providing and fixing NICKEL chrome platedcopper alloy Fancy two way long body bib cockwith wall flance Jaquar make or ARK supremeConfirming to IS 8931;1993

a) 15 mm nominal bore

Providing and fixing C.P concealed angle stop cock (heavy) with wall flange of (ARK SUPREME/JAQUAR) make 15 mm nominal bore

Proving and fixing white vitreous china watercloset squatting pan (Indian type w.c. pan) size580 mm with 100 mm sand cast iron P. or S trap10 litres high level P.V.C. flushing cister (ofapproved make) with fittings, rack bolts 32 mmdiameter P.V.C telescopic flush pipe with fittings and clamps 25mm P.V.C. over flow pipe with specials & mosquito proof coupling ofapproved municipal design and nylon pullcomplete cutting and making good the walls andfloors where required(HINDUSTAN/CERA)

b) Orissa pattern W.C. pan

Providing and fixing vitreous China water closet squatting (European type W.C pan) with seat and lid C.P brass hinges and rubber buffers 10 lts high level PVC flushing cistern ( of cera conventional “s” /p trap) with fittings rack bolts, 32 mm, dia PVC telescopic flush pipe with fittings and clamps 25 mm PVC over flow pipe with specials & mosquito proof coupling of approved municipal design and nylon chain and pull complete, cutting & making good the walls & floors where required. ( HINDUSTAN/CERA)

a) WC pan – Hindustan /Cera conventional EWC of white colour with white plastic lid & seat.

b) PVC FLUSHING CISTERN ( HINDUSTAN/CERA)

White colour Hindustan sleek with all fittings.

Providing and fixing vitreous china wall hung wash basin inclusive of all fixing accessories and Jaquar make fittings etc.complete. -JAQ ALD-CHR-709 L130 coupling -JAQ ALE-CHR-773 ML190X125 bottle trap -JAQ-PRS-CHR-031 Pillar Cock auto closing system -18’’ connection pipe of ARK make a) White colour under counter rectangular wash basin of size 420 x 420 x 155 mm. Jaquar make.

Providing and fixing vitreous china under counter wash basin inclusive of all fixing accessories and Jaquar make fittings etc. complete. -JAQ ALD-CHR-709 L130 coupling -JAQ ALE-CHR-773 ML190X125 bottle trap -JAQ-PRS-CHR-031 Pillar Cock auto closing system-18’’ connection pipe of ARK make a) White colour under counter rectangular wash basin of size 485 x 370 x 205 mm.Jaquar make.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 including cutting of stone and making good the walls wherever required : Kitchen sink with drain board with coupling & all accessories complete with choke stop strainer, Plain type having flat borders for correct sandwithing between the plaform top and bottom slabs complete

(a)Overall size 1040mmx510mm (41"x20") bowl size 460mmx410mmx200mm (18"x 16"x 8") depth 200 mm. Glossy. 1.0mm thk,

Providing & fixing bevelled edge mirror ofsuperior glass (5mm thk) of approved Quality,shape & size complete with CP brass screws andwashers, Cleats, CP studs etc Complete.

Providing and fixing C.P jali (Round)

Making connection of G.I distribution branch with main 50mm to 80mm nominal bore by providing and fixing tee including treading the pipe etc complete.

Providing and fixing P.V.C. connection pipe with brass unions 15 mm nominal bore:

c) 18” (45 cm) length (ARK make)

Providing and fixing brass full way valve (heavy) duty with wheel of approved quality. ZOLOTO make

b) 20 mm nominal bore

c) 25 mm nominal bore

d) 32 mm nominal bore

e) 40 mm nominal bore

f) 50 mm nominal bore

g) 65 mm nominal bore

Providing and fixing nahani trap of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, without door :

a) 110 mm dia

Providing and fixing 40mm dia GI pipes outlet in cement mortar 1:3 ( 1cement : 3 fine sand) including cutting and making good the wall

Providing & fixing CP brass towel rail fixed in wooden cleats with CP brass screws

a) 24” size CAN- CHR- 1111SM, Jaquar make

Providing & fixing soap dish chromium plated fixed to wooden cleats with CP brass screws.

a) Soap dish, JAQUAR make CHR -1131N

Providing and fixing Hand Shower (Health Faucet) with 8mm dia, ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainles steel flexible hose) and wall hook of approved quality confirming to IS standards.( Jaquar or ARK supreme)

Providing and fixing CP Brass toilet paper holder fixed to wooden cleats with CP brass screws a) JAQUAR make(CHR-1151N)

Providing and fixing urinal valve auto closing system CP with built in control cock with 8 mm dia 300 mm long pipe, wall flange etc. complete. JACQUAR make (PRS-CHR-077)

Providing and fixing WHITE vitreous china flat back lipped front Urinal basin of JAQUAR Make inclusive of C.P waste coupling, dome shaped, Urinal spreader, Urinal bracket ( Cat no :URS-WHT-13257)

Providing and placing on terrace roof of floor two (1st floor roof) single piece rotational moulded polythene water storage tank having ISI mark and confirming to IS 12701; 1996 including tank connectors.

b) 500 lit. capacity

c) 1000 lit capacity

Jointing of rigid SEL FIT PVC pipes by cleaning the pipes with solvent cement including the cost of solvent cement and hydraulic testing of joints etc. complete as per IS : 7634- 19 75 Part : 3, including hydraulic testing of joints as directed by the Engineer in Charge

Outer dia in mm

Conveying carefully from stack at site, 250mm from both sides rolling and lowering in trenches, laying true to line and level and perfect linking for joints for PVC/HDPE complete in all respects as per the direction of the Engineer-in-Charge

Supplying at store or site of work Rigid PVC (SEL FIT) pipes for public water supply including Railway freight, carting, loading and unloading, stacking, transit insurance etc. complete, Conforming to IS: 4985-2000, and bearing ISI mark, Class 6 kg/cm2. Outer Dia in mm

Supplying at store or site of work Rigid PVC (SEL FIT)pipes for public water supply including Railway freight,carting, loading and unloading, stackig, transit insuranceetc. complete, Conforming to IS: 4985-2000, and bearingISI mark, Class 10 kg/cm2.

Outer Dia in mm

Supplying and fixing at the site of work of Steel FibreReinforced Concrete (SFRC) manhole covers withframes made as per IS :12592 (part I and II )- 1991 inconcrete M45grade. The covers and lapped in 2mmthick. steel plate and this plate & lifting hooks are dulypainted in corrosion resistant epoxy paint etc. complete.

I Light Duty ( 2.50 Metric Tonne Capacity)

Size in mm

Skylight - Danpalon Or Equivalent Day light PanelSystem: Supply & fixing of 16mm thick 600 mmwidth MULTIWAL MULTICELL polycarbonatesystem consist of: The panels shall be niform incolor with an integral Microcell core. In a crosssection, the core shall be constructed of tightcells with 6 walls. Panels will be supplied withVertical Standing Seam at both sides of the panelSnap-on connector to interlock the panels shallhave a grip-lock double tooth lockingmechanism to ensure maximum uplift capability& shall be of same color as that of panel foraesthetic appeal.NOTE : Necessary Steel structure to be providedby the Steel fabricator. Skylights framework tobe raised by by 200 mm from Roof Pan level.

Providing and fixing colour coated galvulium roofing sheets of 0.5mm thickness including allthe accessories (TATA / JSW make) but excluding thecost of purlins, rafters, trusses, flashings etc.complete as per the directions of the Engineer incharge.

Providing and fixing colour coated Galvulium Flashings of 0.5 mm thickness( TATA / JSW Make) in - corners,ridges,valleys, gable end and trims Girth up to 610 mm including all the accessories complete as per the directions of the Engineer in Charge.

Providing and Fixing in position Double Skin Standing Seam MxSeam or equivalant Standing Seam Roofing Sheet in 0.55 mm thickness Color Coated Galvalume / Zincalume Steel Sheets with Galvanised Clips. The feed material is manufactured out of nominal 0.55 mm total coated thickness (TCT) & 0.50 mm base metal thickness (BMT), Hi-tensile steel having 245~300 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 43.5% Zinc & 1.5% Silicon) as per AS 1397 – ZincAl AZ 150 (min. 150 grams / sq. m. total on both sides) with Super Durable Polyester (SDP) Paint finish. The SDP paint will have a total coating thickness of 25 ~ 30 micron, comprising of nominal 20 micron exterior coat on top surface and nominal 5 micron reverse coat on back surface over nominal 5 micron primer coat on both surfaces of approved color shade by concern authority. The profile sheet will be of TATA BlueScope Steel (TBSL) or JSW SDP or Equivalent make, necessary Test Certifcate has to be provided. Top Skin elements to be supplied in single length with no laps with a sheet element cover width of 480 mm and a standing seam height of 45 mm. Sheets are to be laid to meet the requirements of the building geometry. The roof elements will be supported by and joined longitudinally with an electrically operated closure machine over concealed galvanised clips integrated into the longitudinal element flange thereby allowing for the possibility of transmitting reaction forces resulting from positive and/or negative loads and also accommodating unobstructed thermal movements resulting from the specific ambient temperature variation.The secret fix galvanised clips shall be capable of transmitting all reaction forces to the purlin without the aid of any other material, thus resulting in an overall “Self-supporting standing seam roof system”. Base Coil : TBSL or JSW SDP or Equivalant make. Rockwool Insulation layer of 50 mm thick, 48kg/m3 density to be laid between two sheets. "Z" Type GI Sub-girt of size 40 x 50 x 40 – 1.5 mm thick will be fixed on liner sheets at all along purlin, the height of 50 mm will cater the thickness of 50 mm thick insulation. Liner Sheets shall be of MxLine or equivalant Profile of having nominal 1050 mm effective cover width and 18 mm corrugation depth at 175 mm center to center spacing in Colour Coated Galvalume / Zincalume Steel materials. The feed material is manufactured out of nominal (0.42 mm BMT) 0.50 mm total coated thickness (TCT), Hi-tensile steel with minimum 550 MPa yield strength, metallic hot dipped coated with Aluminium Zinc alloy (55% Aluminium, 43.3% Zinc & 1.6% Silicon) as per AS 1397 - Zinc-Alu. AZ 150 (min. 150 grams/ sq. m. total on both sides) with Super Durable Polyester (SDP) Paint. The paint will have a total coating thickness of nominal 25 µm, comprising of nominal 20 µm exterior coat on top surface andnominal 5 µm reverse coat on back surface over nominal 5 µm primer coat on both surfaces of approved colour shade by concern authority. the steel sheet shall be fastened with nominal 40 micron zinc coated or nominal 25 micron zinc-tin allow coated , hex head, self drilling screw as per aAS 3566-2002 Class -3 fastners of approved make with EPDM washers as per the requirement considering the profile shape and design load. the fastnes size shall be calculated as per the design or manufacturers recommendations.

Providing and fixing 0.50mm thick colour coated galvulium Rain Water gutter with machine cut and press bend in as per approved design in line level along with gutter strip, silicon sealant, SDS, etc.complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section (CHS) IS1161 closed Structural Steel of (SAIL, TATA. VIZAG, JSW ,APOLLO Steel Ltd.) make (Min Yeild Stress 310 Mpa)) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Steel work welded ( SAIL, TATA, VIZAG & using electrodes of AdOr make only) in built up sections trusses and framed work including cutting, hoisting, fixing in position with anchor fasteners ( Hilti HST) and applying zinc chromite primer

b) In tees, angles ,flats and channels as per the design

Supplying & installation of 600mm dia wind operated turbo ventilator fans for normal/smoke exhaust with FRP base plate, etc.complete.

Construction of embankement with approved material obtained from borrowpits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting with vibratory roller to meet requirement of Table 300-2 as per MORTH specification 305

Supplying of laterite stone soling of size 150-200 mm size and murrum having P.I. Value not more than 6 and laying including packing with smaller stones and consolidation with power road roller including spreading, watering and consolidation of binding material etc.(Measurements shall be considered on finished item) .

Providing and fixing Terracotta Clay Jalli of size 0.20m x 0.20m x 75mm including transportation and labour charges complete

Providing and fixing Aluminium shutters (Jindal make) 27mm-Domal series windows with aluminium cleating system as per design including transportation, scaffolding and handling etc, complete. Windows with two track ,two sliding shutters with outer frame 63mm x 45mm and 4 glass shutters 65mm x 27mm kinlong touch lock, epdm gasket, all screws of S.S 304 grade fixing screws of HILTI make complete with G.P Silicon ( excluding GST) (i) 5mm clear annealed glass of St.Gobain/AIS

Providing and sealing 25mm wide vertical and horizontal expansion joints with kemperol waterproofing system as per manufacturer specification including necesarry hardware, scaffolding, etc complete

Making holes in RCC structure i.e. slabs, beams and columns by core cutting upto required depth & size up to 5" dia

Supply installtion, testing and commisioing of Main LT panel Single front, compartmentalized, ,indoor, Construction: Structural members – 2.5mm , doors – 1.6mm CRCA, covers & partitions – 1.6mm CRCA, base frame –75x75x5mm CRCA, Component Mounting Plates – 2mm CRCA, Gland Plates – 2mm CRCA, Gaskets: Soft EPDM rubber gaskets, completely derusted, chemically treated in 7 tank process Painting/ Powder coating in RAL 7032 Siemens Grey, Cable Entry – Incomer & Outgoing: bottom:, Degree of Protection – IP52, Applicable Standard: IS:8623-1994, Insulation Volts: 660V, 50-60Hz, System Volts: 415V, 50Hz, 3-phase, 4-wire, Ambient Temperature: 40oC, Relative Humidity: 90%

Busbars 2 sets, Material: Aluminium alloy 63401-WP to IS:5082-1998, four pole, Continuous current rating: 2000A: Bus bar Supports :Non Hygroscopic SMC Supports , Isc = 50kA/1 sec

INCOMER1- to Bus Bar1, 1 no for 1000KVA Transformer, equipped with 2000A 4P EDO ACB, 50KA,microprocessor based Over current, Short circuit and Earth fault relay, 240V controls 4NO+4NC aux contacts and 1 no. fault sig contact, digital multifunction meter read volts,amps,frequency,pf, Maximum Demand, 96x96, class 1.0, aux, supply 90-270VAC, with RS 485 port , 2000/5A 15VA CT suitable for connecting to APFCR. Outgoing 1 no 100A 4P thermal magnetic release with overload, shortcircuit and earth fault release suitable for termination OLTC cables. Aluminium bus bar links suitable for terminating incoming power cables of size 5//3.5Cx300 mm2

INCOMER2 to BusBar2- 1 no. for DG, equipped with 1000A 4P EDO microprocrssor based ACB with AMF, 50KA, with Over current, Short circuit and Earth fault release, 240VAC controls,4NO+4NC aux contacts, 1no fault sig. contact. Microprocessor based earth leakage relay 30-300mA (18steps) sensitivity. 85-275VAC aux, supply, 2 co contacts with tape wound rectangular CBCT.Trip-Neutral-close switch, momentary, spring return to normal, 25A, 1no+1nc per way. 1no 6A single pole control MCB, 10KA C curve. Supply indicating led R Y B lamps, ON indication RED lamp, Off indicating led lamp Green, Trip indicating led lamp. Digital multifunction meter to read volts,amps,frequency, pf, KVA, KWH, KVAH, KVRAH 96x96 with rectangular polyamide CT class 1.0. Aux, supply 90-270VAC, without RS 485 port. Aluminium bus bar links suitable for terminating incoming power cables of size 3//3.5Cx400 mm2

Bus Coupler, 1 no for above two bus bars with 1000A 4P EDO ACB, 50KA, microprocessor based Over current, Short circuit and Earth fault relay, 240V controls 4NO+4NC aux contacts and 1 no. fault sig contact, aux, supply 90-270VAC, with RS 485 port, providing necessary signals and cable to start/stop the DG when transformer ACB is OFF with settable timings, with potential free contact to trip the transformer breaker, and interlocking with DG ACB so that the bus coupler can be made ON only when DG ACB is OFF.

Outgoings from bus bars1

Outgoing1 from bus bar1 630A thermal magnetic based 4P MCCB with 12 stage APFC relay with CTs with 2000A 50KA bus bars with outgoings 2 sets of 200A TP fuses with 100KVAR app type capacitor, 2 sets 150A TP fuses with 50KVAR APP type capacitors. 1 set of 100A TPN Fuses with 25KVAR APP type capacitors, 2 sets of 100A Fuses with 12.5KVAR APP type capacitors

Outgoing2 from bus bar1, 2 sets of 400A FP MCCB 36KA fixed type ,thermal magnetic type with overload and short circuit protection with Extended operating rotary handle for mccb with door interlock spreader terminal for mccb 1co auxiliary +1 co fault indicating contact for mccb, 6A single pole control mcb, C curve, 10 KA , 15A disconnecting type neural link, ON indicating lamp, red, LED type, 240VAC , OFF indicating lamp, green , LED type , 240 VAC , outgoing power cables each of size 2//3.5Cx300 mm2

Outgoing3 from bus bar1, 1no 630A FP MCCB 36KA fixed type ,thermal magnetic type with overload and short circuit protection with Extended operating rotary handle for mccb with door interlock spreader terminal for mccb 1co auxiliary +1 co fault indicating contact for mccb, 6A single pole control mcb, C curve, 10 KA , 15A disconnecting type neural link, ON indicating lamp, red, LED type, 240VAC , OFF indicating lamp, green , LED type , 240 VAC , outgoing power cables each of size 3// 3.5Cx300 mm2

Outgoing4 -from bus bar1, 1 no equipped with 100A 4P fixed type thermo magnetic 36KA MCCB with overload and short circuit protection with Extended operating rotary handle for mccb with door interlock for RTCC indoor panel controller

Outgoings from bus bars2

Outgoing1 from bus bar2, 3sets 300A 4P MCCB, 36KAfixed type Thermal magnetic type with overload and short circuit protection with Extended operating rotary handle for mccb with door interlock spreader terminal for mccb 1co auxiliary +1 co fault indicating contact for mccb, 6A single pole control mcb, C curve, 10 KA , 15A disconnecting type neural link, ON indicating lamp, red, LED type, 240VAC , OFF indicating lamp, green , LED type , 240 VAC , outgoing power cables each of size 2//3.5Cx300 mm2

Outgoing2 from bus bar2 100A 4P MCCB, 36KAfixed type Thermal magnetic type with overload and short circuit protection with Extended operating rotary handle for mccb with door interlock spreader terminal for mccb 1co auxiliary +1 co fault indicating contact for mccb, 6A single pole control mcb, C curve, 10 KA , 15A disconnecting type neural link, ON indicating lamp, red, LED type, 240VAC , OFF indicating lamp, green , LED type , 240 VAC , outgoing power cables each of size 3.5Cx50 mm2

Main LT Panel as above

Design & supply of Lighting main distribution panel cubical type ,floor mounted , front access ,fully compartmentalised with cable entry at top/ bottom, all mccbs with rotary handles with thermal magnetic releases. Steel sheets used in the construction shall be 2 mm thick. All sheet steel work shall undergo a process of degreasing, pickling in acid, cold-rinsing, phosphating, passivating and then sprayed with a high corrosive resistant primer. The finishing treatment shall be by application of two coats of synthetic enamel paint or powder coating of RAL7032. The panel shall be of adequate size with a provision of 25% spare space to accommodate possible future switch gear. The cable terminations shall be suitable for cable sizes as shown on the drawing as required etc. suitable for outgoing cable sizes as shown on the drawing as required with

Incomer 400A TPN 37KA mccb with thermal magnetic releases suitable for 2x31/2cx300sqmm AYFY cable

1 sets of digital multifunction meter with Amps, Volts, Kwh, Hz,PF etc. with scada connectivity with necessary cts and suitable RS485/232 port

800A 4P copper bus bars of 99.9% purity electrolytic copper

Outgoing1

400A TPN 37KA mccb with thermal magnetic releases

800A 4P copper bus bars of 99.9% purity electrolytic copper with

SUB Outgoing1 for ground floor with

160A TPN 37KA mccb with thermal magnetic releases with

200A 4P copper bus bars of 99.9% purity electrolytic copper with 11 nos of 40A tpn mccb 37ka and 1 no of 60A TPN MCCB 37KA

SUB Outgoing2 for first floor with

160A TPN 37KA mccb with thermal magnetic releases with

200A 4P copper bus bars of 99.9% purity electrolytic copper with 11 nos of 40A tpn mccb 37ka

SUB Outgoing3 for second floor with

160A TPN 37KA mccb with thermal magnetic releases with

200A 4P copper bus bars of 99.9% purity electrolytic copper with 9 nos of 40A tpn mccb 37ka

Outgoing 2

200A TPN 37KA mccb with thermal magnetic releases suitable for 31/2cx300sqmm AYFY cable

Lighting distribution panel as above

Design & supply of UPS main distribution panel cubical type ,floor mounted , front access ,fully compartmentalised with cable entry at top/ bottom, all mccbs with rotary handles with thermal magnetic releases. Steel sheets used in the construction shall be 2 mm thick. All sheet steel work shall undergo a process of degreasing, pickling in acid, cold-rinsing, phosphating, passivating and then sprayed with a high corrosive resistant primer. The finishing treatment shall be by application of two coats of synthetic enamel paint or powder coating of RAL7032. The panel shall be of adequate size with a provision of 25% spare space to accommodate possible future switch gear. The cable terminations shall be suitable for cable sizes as shown on the drawing as required etc. suitable for outgoing cable sizes as shown on the drawing as required with

Incomer 160A TPN 37KA mccb with thermal magnetic releases suitable for 2x31/2cx150sqmm AYFY cable

1 sets of digital multifunction meter with Amps, Volts, Kwh, Hz,PF etc. with scada connectivity with necessary cts and suitable RS485/232 port

400A 4P copper bus bars of 99.9% purity electrolytic copper

Outgoing1 for ground floor

60A TPN 37KA mccb with thermal magnetic releases with '200A 4P copper bus bars of 99.9% purity electrolytic copper with 8 sets of 40A TPN 37KA MCCB

Outgoing2 for first floor

100A TPN 37KA mccb with thermal magnetic releases with '200A 4P copper bus bars of 99.9% purity electrolytic copper with 8 sets of 40A TPN 37KA MCCB

Outgoing3 for second floor

60A TPN 37KA mccb with thermal magnetic releases with '200A 4P copper bus bars of 99.9% purity electrolytic copper with 8 sets of 40A TPN 37KA MCCB

UPS distribution panel as above

Design & supply of AC main distribution panel cubical type ,floor mounted , front access ,fully compartmentalised with cable entry at top/ bottom, all mccbs with rotary handles with thermal magnetic releases. Steel sheets used in the construction shall be 2 mm thick. All sheet steel work shall undergo a process of degreasing, pickling in acid, cold-rinsing, phosphating, passivating and then sprayed with a high corrosive resistant primer. The finishing treatment shall be by application of two coats of synthetic enamel paint or powder coating of RAL7032. The panel shall be of adequate size with a provision of 25% spare space to accommodate possible future switch gear. The cable terminations shall be suitable for cable sizes as shown on the drawing as required etc. suitable for outgoing cable sizes as shown on the drawing as required with

Incomer 500A TPN 37KA mccb with thermal magnetic releases suitable for 2x31/2cx300sqmm AYFY cable

1 sets of digital multifunction meter with Amps, Volts, Kwh, Hz,PF etc. with scada connectivity with necessary cts and suitable RS485/232 port

800A 4P copper bus bars of 99.9% purity electrolytic copper

Outgoing1 for ground floor

200A TPN 37KA mccb with thermal magnetic releases with '400A 4P copper bus bars of 99.9% purity electrolytic copper with 6 sets of 40A TPN 37KA MCCB

Outgoing2 for first floor

200A TPN 37KA mccb with thermal magnetic releases with '400A 4P copper bus bars of 99.9% purity electrolytic copper with 8 sets of 60A TPN 37KA MCCB

Outgoing3 for second floor

200A TPN 37KA mccb with thermal magnetic releases with '400A 4P copper bus bars of 99.9% purity electrolytic copper with 7 sets of 60A TPN 37KA MCCB

AC distribution panel as above

Design & supply of UPS main panels cubical type ,floor mounted , front access ,fully compartmentalised with cable entry at top/ bottom, all mccbs with rotary handles with thermal magnetic releases. Steel sheets used in the construction shall be 2 mm thick. All sheet steel work shall undergo a process of degreasing, pickling in acid, cold-rinsing, phosphating, passivating and then sprayed with a high corrosive resistant primer. The finishing treatment shall be by application of two coats of synthetic enamel paint or powder coating of RAL7032. The panel shall be of adequate size with a provision of 25% spare space to accommodate possible future switch gear. The cable terminations shall be suitable for cable sizes as shown on the drawing as required etc. suitable for outgoing cable sizes as shown on the drawing as required with

Incomer 200A TPN 37KA mccb with thermal magnetic releases suitable for 31/2cx300sqmm AYFY cable

1 sets of digital multifunction meter with Amps, Volts, Kwh, Hz,PF etc. with scada connectivity with necessary cts and suitable RS485/232 port

400A 4P copper bus bars of 99.9% purity electrolytic copper

Outgoing

3 sets of 60A TPN 37KA mccb with thermal magnetic releases

UPS panels as above

Supplying, installing, testing & commissioning 3 phase, 11/0.433 kV, 50 Hz., 1000 kVA, Mineral oil immersed and naturally cooled outdoor type, Copper wound ,without gas cushioning ,hermetically Sealed transformer, delta/star connected additional neutral brought out on load side, temperature rise should not exceed 45℃ by thermometer in oil and 50℃ by the resistance method in winding at full load rating, using type A winding insulation (kraft paper) with HV tapping (with on load tap changer) on load +5 to -15 in steps of 2.5%, with standard accessories complete with test certificate with losses below 2790 Watts at 50% load, 7700 Watts at 100% load as per IS:1180 (part 1) : 2014 with necessary permissions of Electrical Inspector, as per specification no SS- TR-SL

Supply of following size of 3 core, HV, 11 KV grade, ISI mark, XLPE cable with stranded compact circular aluminium conductor, conductor screened with extruded semiconducting compound, XLPE insulated, insulation screned with extruded semiconducting compound in combination with copper tape(0.3 KA for 1Sec.) cores laid off,inner sheath of PVC tape,galvanised steel flat strip armoured and overall PVC sheathed cable conforming to IS:7098(Part II) with latest amendments.

3 Core 95 sq.mm

Supply of armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I),IS:7098(Part I) with latest amendments of following size.

(10) 3 1/2cx300 sq.mm

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of exceeding 120 sq.mm but not exceeding 400 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required.

b) In rocky strata

Laying of one number additional PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 120 sq.mm but not exceeding 400sqmm direct in ground in the same trench in one tier horizontal formation including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick, protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required.

b) In rocky strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of grade exceeding 1.1 KV but not exceeding 11 KV grade of size not exceeding 120 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed lenghtwise on top of cable all over the run and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required.

(b) Rocky strata

Supplying and making cable end terminations with brass compression gland and copper lugs for following sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required.

(11) 3 1/2 x 300 Sq. mm.

Supplying and making Indoor cable end termination with heat shrinkable kit for following sizes of PVC insulated PVC sheathed/XLPE aluminium conductor cable upto 11 KV grade, complete as required.

(b) 11 KV, 3 Core x 50 - 95 sq.mm

Steel work in single sections (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only) including cutting, hoisting fixing in position and applying a priming coat of red lead paint.

a) In R.S. joists, channels, angles, tees

b) In flats of all sizes

Providing printed instruction chart for treating persons suffering from electric shock, printed in English & Marathi and duly laminated complete

Providing pair of duly tested rubber hand gloves as per IS :47705 suitable for working up to 22 kV supply complete.

Supplying standard first aid box with necessary antiseptic cream, medicine for use on wounds due burn, crepe bandage, gauge bandage, medicated ready to use bandage (Band-Aid) adhesive tape for medicinal use, scissors, anti-septic solution, etc. (All above contents shall be of standard makes)

Supplying and fixing PVC synthetic elastomer electrically insulating mat with class A insulation conforming to IS: 15652 – 2006 having 2 mm thickness up to 3.3 kV

Supplying and fixing PVC synthetic elastomer electrically insulating mat with class B insulation conforming to IS: 15652 – 2006 having 2.5 mm thickness up to 11 Kv

Supplying SMC chequered plates of size 4ft x 2ft, hot press moulded from advanced composites of plastics namely sheet moulding compound of thickness 2.5 mm with insulation level up to 22 kV and fixing it to substation floor with SR-998 adhesive along with 5 mm thick E.P. foam complete.

Supplying and erecting fencing of section having size 2450 mm in height from ground level and 1200 mm width chain link wire mesh (jali) with angle iron frame work erected in CC foundation and painted complete as required

Supplying and erecting double leaf hinged door each 1500 mm in width x 1850 mm in height using B class, GI pipe with angle iron supports, chain link wire mesh (jali) complete supported on channel iron, erected in foundation, and painted complete as required

Supplying and erecting 50 x 50 x 6 mm angle iron as corner support 2m long fixed at the middle of the fencing frame and the other side inclined at 30 degree angle, in cement concrete foundation of 15 x 15 x 40 cm complete duly painted with one coat of red oxide and two coats aluminium paint complete.

Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made complete

Supplying, installation, testing and commissioning of main fire pump (MFP / EP) suitable for water discharge of 1600 to 1800 LPM at 70 to 55 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 30kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal type, single stage, centrifugal/split casing pump of cast iron body & bronze impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/SSC/EP

Supplying and erecting 100 mm dia. pressure gauge , 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, erected with provided G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG

Supplying and erecting 12/15 mm dia pressure switch with provided isolation valve, G.I. nipple, elbow, etc complete as per specification no. FF-FFA/PS

Supplying and erecting 100 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Supplying and erecting 100 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Supplying, erecting, testing & commissioning of fire pump control panel (FCP) of cubical construction, floor mounted type, fabricated from minimum 2 mm thick CRCA sheet, compartmentalised with hinged lockable doors, with enclosure protection class IP54, duly powder coated or painted with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003), cable alley, interconnection with suitable size solid copper busbar strip of adequate size for all power connections having switchgears and accessories, mountings and internal wiring with adequate size copper conductor cable, earth terminals, numbering etc. complete in all respect, suitable for satisfactory operation of main fire pump and jockey (pressurisation) pumps (1working+1standby) with necessary accessories, wiring & cabling along with allied accessories with following incoming and outgoings, suitable for automatic & manual operation on 415V, 3 phase, 50Hz ac supply as per specifications

Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G.I. Rod complete with all materials testing and recording the results as per specification no. EA-EP

Supplying and erecting Fire Hydrant Double Door Hose Box (Shabhogilal/Newage Make)

Supplying and erecting 63mm dia, reinforced rubber lined (R.R.L.) hose pipe, 15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/RRL

Supplying and erecting stainless steel branch pipe 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specifications no. FFFFA/ NZ

Supplying and erecting stainless steel single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV

Supplying and erecting fire brigade header ( Siamese connection )of 150 mm dia, for supplying water in fire tank complete as per specification no. FFFA/ FMC)

Supplying and erecting G.I. pipe ‘C’ class ERW 100 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying & installing of Signages for Exit/Extinguisher/Call Points/ Hose Station And Evacuation Layout. Etc (Prolite Make)

S u p p l y i n g & erectingABC fire extinguisher of 6kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete.

S u p p l y i n g & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete.

Supplying & installing Structural Support (MS C Channel and L- Angle of appropriate size)

Supplying & installing Push button at ground floor with cable

Supplying, erecting testing and commissioning beam smoke detector four wire single ended reflected type with 8 " receiver having digital display for easy alignment, adjustable sensitivity & heater kit for transmitter/receiver and reflector with necessary connections on suitable back box. The protection range of beam detector is 5 to 70 m.

Supplying, installing, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the 2 loop capacity and capable of supporting upto 250 devices and detectors per loop, with on-board LCD display with min 16 lines of text, operating at 230 V 50 HZ - AC with inbuilt Battery Backup of a minimum 24 hours in normal condition and 30 min in alarm condition, suitable provision for network connectivity, interfacing with third party equipment via a MODBUS/ OPC/ L-ON interface etc. conforming to IS 15908:2021, IS 2189: 2008, EN 54 & VDS / FM/ UL 864 (10th edition) with 3 years replacement warranty FF-AFAS/CP.

Supplying, installing, testing and commissioning FR, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU

Supplying, erecting, testing and commissioning hooters having high (100dB @ 1m) and low (94dB @ 1m) volume setting, group addressing facility allowing multiple sounders to be activated with CRCA enclosure complete as per specification no. FF-FAAS/HTR

Supplying, erecting testing and commissioning manual call point (Pill box) with break glass, push button (resettable type) in metal enclosure complete as per specification no. FF-FAAS/MCP

Supplying, erecting testing and commissioning optical type smoke detector on suitable back box with necessary connections complete as per specification no. FF-FAS/SD

Supplying, erecting testing and commissioning Relay Module

Supplying, erecting testing and commissioning Isolation Module

Supplying, erecting testing and commissioning Hose reel drum

Supplying, erecting testing and commissioning Y type strainer-100NB

Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI mark, of approved brands including accessories and providing masonry enclosure with CI/RCC cover having locking /Lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size not less than 1.0x1.0x 2.0 mtrs(min) and disposal of excavated soil. b) Class B GI pipe, 40mm diameter as per specifications. c) Charcoal/salt as per specs ( paid separately). d) Refilling the pit of size not less than 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe . g)watering arrangement(plumbing will be paid separately).

(b) In rocky strata

Extra for using salt and charcoal for pipe earth electrode as required( 65 Kgs of Charcoal and 5 Kgs of Salt).

Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosure with CI/RCC cover having locking/Lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 3.0 mtrs(min) and disposal of excavated soil. b)Watering GI pipe, 20mm, Class B, with funnel as per specs. c)Charcoal/salt as per specs (paid separately). d) Refilling the pit of size 1.0x1.0x 3.0mtrs(min) with soft black agriculture soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe.g)watering arrangement(plumbing will be paid separately).

(b) In rocky strata

Earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonry enclosure with CI/RCC cover having locking/lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 3.0 mtrs(min) and disposal of excavated soil. c)Watering GI pipe, 20 mm Class B, with funnel as per specs. d) Charcoal/salt as per specs ( paid seperately). e) Refilling the pit of size 1.0x1.0x 3.0 mtrs(min) with soft black agriculture soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. g)watering arrangement (plumbing will be paid seperately).

(b) In rocky strata

Extra for using salt and charcoal for GI or Copper plate earth electrode as required (96kgs of charcoal and 5kgs of salt)

Supplying and laying 25 mm x 6 mm GI strip at 0.5 m below ground as strip earth electrode including soldering etc. as required

Supplying and laying 25 mm x 5 mm copper strip in 40 mm dia GI pipe from earth electrode as required

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) with modular switch, modular plates,suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

(f) Group C -- with Cat B Modular Accessories

Wiring for group controlled light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) with 2 way modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

(a) with Cat A Modular accessories

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/ 6 A modular switch connection painting etc. as required.

(b) Cat B

Supplying and fixing Pop up type flush mounting box 4 module on counter/table alongwith modular base and cover plate for modulator switches in recess etc. as required of Legrand or equivalent and fixing 1no 3 pin 5A socket, 1no 5A switch and 1no RJ-45 outlet

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 15/16 A and 5/6 A modular socket outlet modular socket outlet and 15/16 A modular switch connection painting etc. as required. (b) Cat B

Supply and erecting fan hook box ( 100 mm diameter or equivalent square size, 75mm deep) fabricated out of 16 SWG sheet steel with 10 m round bar hook bounded to RCC steel upto 50 mm length protruding on each side of the box, including painting with 2 coats of red oxide, complete as required.

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required

(b) Cat B

Supplying and erecting of 48 inch (1200mm sweep) ceiling fan, double ball bearing type complete with all accessories

(b) Cat B

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit (heavy)of appropriate size as required.

(b)2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit)

(c) 2 x 4 sq.mm + 1 x 4 sq.mm earthwire (20mm Conduit)

(i) 4 x 4 sq.mm + 2 x 4 sq.mm earthwire (25mm Conduit)

(j) 4 x 6 sq.mm + 2 x 6 sq.mm earthwire (32mm Conduit)

(k) 4 x 10 sq.mm + 2 x 10 sq.mm earthwire (32mm Conduit)

Supply and erecting of 9 inch (225 mm sweep) exhaust fan with double ball bearing 1400 rpm, complete with all accessories.

(a) Cat A

Supplying and erecting slotted angles, frames, strips, etc. for fixing of trays complete with bending, cutting, drilling and welding complete erected at the position with necessary materials such as nut bolts,etc duly painted with one coat of red oxide and two coats of enamel paint to match the structures or as per directions

Supplying and fixing following way TPN sheet steel, double door, Verticle type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator)interconnection between incomer MCB and busbars of following ways (but without MCBs as required)

(d) 4 way (8+12), double door, Vertical type, Cat B

(e) 8 way (8+24), double door, Vertical type, Cat B

(f) 12 way (8+36), double door, Vertical type, Cat B

Supplying and fixing B series SP MCB 240V, suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required"

(c )5A TO 32A, Cat B

Supplying and fixing 40 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required.

(f) SP, Cat B

Supplying and fixing 63 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required.

(i) TP Cat B

(J) TPN Cat B

Supplying and erecting integrated LED flood light fitting Max. 50W IP65 & IK07 class having pressure die-cast aluminium housing, having system lumens output of Min. 5000 Lumens, min. efficacy of 100 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50, including driver with U shaped bracket with 3 Years warranty as per specification No FG-ODF/FLS2

Supplying & erecting LED 40W tube light fitting (4 feet), 5700K, with CRCA housing, heat sink, with industrial grade heavy duty driver complete Havels Cat stout mini 1200bs 40w led 865 spcwh OR Wipro cat no LL24-541-XXX-57-CD (including lamp).

Supplying and fixing stiff pendant with 600 mm long 20 mm dia x 1.6 mm thick steel conduit aluminium cast back plate and brass holder complete including wiring the down rod with 1.5 sq.mm FR PVC insulated copper conductor single core cable and painting etc. as required.

Supply and fixing of cable route marker 15 cms diameter of GI plate 6mm thick with inscription thereon bolted or welded to 25mm x 25mmx 5mm angle iron 60 cms long and fixing the same in ground with PCC etc complete as required.

Supplying & laying (including excavation) reinforced cement concrete pipe of IS 458:2003 NP-2 class of 150 mm internal diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete.

Supplying and Installing following size perforated type 16 SWG, M.S.cable tray of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required.

100mm width x 50mm depth

150mm width x 50mm depth

Supplying and Installing following size perforated type , M.S.cable tray bends of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required.

100mm width x 50mm depth (16 SWG)

150mm width x 50mm depth (16 SWG)

Supplying and Installing following size perforated type , M.S.cable tray tees of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required.

100mm width x 50mm depth (16 SWG)

150mm width x 50mm depth (16 SWG)

Supplying and Installing following size welded ladder type , 50mm depth, M.S.cable tray of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required.

150 mm width X 50 mm depth with runner size 15x50x15mm, rung size 20x40x20mm with rungs at 250mm c/c.(14SWG)

200 mm width X 50 mm depth with runner size 15x50x15mm, rung size 20x40x20mm with rungs at 250mm c/c.(14SWG)

300 mm width X 50 mm depth with runner size 15x50x15mm, rung size 20x40x20mm with rungs at 250mm c/c.(14SWG)

Supplying and fixing tool-less shutter keystone jack (RJ-45) in provided patch panel complete as per specification no. WG-NAS/KJ

Supplying and fixing 9U wall mount rack (Dimension-DxWxH – 500x600x500mm) as per specification No. WG-NAS/RAK

Supplying and fixing 15U wall mount rack (Dimension-DxWxH – 500x600x767mm) as per specification No. WG-NAS/RAK

Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NA

Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and drawing of Cat - 6 UTP, 4 pair annealed tinned copper conductor PVC insulated, PVC sheathed, unarmoured data cable in existing surface/recessed steel/PVC conduit of appropriate size including connection, etc. complete as required

Supplying, installation and testing of suitable size modular GI box , modular plate and cover complete with RJ-45 connector(modular LAN socket TX1000/ CAT6) including concealed metal box/surface GI/PVC Box, modular plate, punching, identifying, complete as required.

Supplying and fixing 1 m UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Supply of IP dome camera , 30m, 2MP with 3.6mm lens , COPPLUS CAT NO CP-UNC-DA21PL3 inclusive of PVC Camera mount/junction box complete

Supply of IP Bullet camera ,2MP with 3.6mm lens, 30m range, CPLUS CAT NO CP-VNC-JA21PL3 inclusive of PVC Camera mount/junction box water proof complete.

Supply of NVR, 256 channel NVR 4K,4 SATA with necessary software, CP-UNR-4K4322, complete.

Supply of Hard Disk Seagate or equivalent 4TB Surveillance specified Hard Drive complete.

Supplying, fixing, and configuring 24 ports, POE switch in provided rack as per specification No. WG-NWC/ENS

Supply of Intex or equivalent 32 Inch LED HD TV with mounting arrangment complete.

Supplying, installing and commisioing of single core Fibre connector as per specification No. WG-NAS/UTPC including numbering etc

Supplying, installing and testing UTP connector (RJ-45) as per specification No. WG-NAS/UTPC.

Supplying of on line UPS pure sine wave of following capacity, 3phase input and output, complete with features like Isolation transformer, input and output protection switchgear, manual change over switch, suitable for 100%unbalanced load etc. along with necessary SMF batteries for 30 minutes backup complete with battery stands, dc connections etc .

Supply and installation of 8 mm Aluminum Round Conductor complete as specified in drawing & Meets the requirements of DIN EN 50164-2 (VDE 0185 part 202) & VDE 0185-305 (IS/IEC 62305) OBO Type No. RD 8/ALU

Supply and installation of Roof conductor holder for parapet- Polyamide Conductor holder:With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder.Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance OBO Type No. 177 30 M8(5207460 )

Polyamide and Install roof cable holder for flat roof: DIN 48829 Form B1. Closed form with bottom. Filling weight 1Kg (frost-resistant concrete). Sleeve from polyethylene, black @ 1 meter distance. OBO Type No. 165 MBG-8-10 ( 5218700 )

Supply and installation of Roof conductor holder - Stainless steel Conductor holder: With Bottom section and conductor holder stainless steel (V2A)Bottom section with Ø 8.5 mm slot. Conductor holder @ 1 meter distance. OBO Type No. 159 VA-V (5217 07 5 )

Supply and installation of 1 mtr vertical air terminal with mounting accessories on the flat surface to meet the requirements of IS/IEC 62305. Tested for Electrical , mechanical and chemical as per IEC 62561. OBO type No.F-FIX JUNIOR (5403308)

Supply and installation of Vertical air terminal with accessories:Providing of Air terminals as per IS-IEC -62305 part-3 Nominal size Ø10/16 mm aluminium rod: 2 Mtr Airterminal: semi-hard (E-AlMgSiO5 corresponds to DIN 48801) Suitable for high wind load.Tested as per IEC 62561(1-8) and relevant test report should be submitted. OBO Type No. 101 VL2000 ( 5401983)

Providing of Stand for Fang Fix system 16 kg with base and clamp ,made up of frost resistant concrete OBO type No.F-FIX-S16 I (5450080)

Providing and installing of Stand for Fang Fix system 16 kg with base and clamp ,made up of frost resistant concrete and tested upto 100KA lightning current. Tested as per IEC 62561(1-8) and relevant test report should be submitted for 100kA lightning current testing. OBO type No.F-FIX-16 (5403200)

Providing of cross universal connector: For T and cross connection, to route vertical down conductor /mesh formation made of hot dipped galvanised iron with necessary screws etc as required. Installed with 4 hexagonal bolts M8*25 with M8 hexagonal nuts . OBO Type No.253 S3 FT ( 5312592 )

Providing and installating of expansion piece with connector: For equalising temperature related length changes. Necessary on conductors length over 20 meters. For round conductor Rd 8/ALU. OBO Type No. 172 AR ( 5218 92 6 )

Supply and Installtion of Connector: For T cross and parallel connectors. Quick installation using hexagonal bolt M10X30 high-grade hot dip galvanised. Conforms to the requirements according to DIN VDE 0185-305 (IS-IEC 62305)(2nos/expansion piece). OBO Type No. 249 B ST ( 5311705 )

Supply and installation of Galvanised Steel Flat 30X3 mm thickness for Ring Earthing as required. Flat conductor Hot Dipped Galvanized. OBO Type No. 5052 DIN 30X3 ( 5450436 )

Supply and installation of Galvanised Steel Flat 30X3 mm thickness for Vertical Column Riser as required. Flat conductor Hot Dipped Galvanized. OBO Type No. 5052 DIN 30X3 ( 5450436 )

Supply and installation of clamp ,For reinforced steel of diameter 6-14mm and RD8-10 Round Conductor. OBO Type no : 1814 FT D14 (5014471)

Providing of Cross connector for Flat: Suitable for 30mm Galvanised steel strip. Installed with 4 nos of hexagonal plate. OBO Type No. 256 S6 FT ( 5314572 )

Providing and installing of earth fixed point: Made of Stainless Steel, grade 316L. Connection to earthing systems, air terminals and reinforcement. Contact plate: 79 mm diameter, made of rustproof stainless steel (V4A). Clamping bolt 10mm diameter, rustproof (V2A). Including plastic cover for simple installation. OBO Type no : 205 DG L180 V4A (5420 02 2)

Supply and installation of clamp ,For reinforced steel of diameter 6-14mm and RD8-10 Round Conductor. OBO Type no : 1814 FT D14 (5014471)

Supply and installation of Connector, Rd 8−10 mm with pressure trough with 1 fix contact clamping screw, nut and serrated washer Including pre-mounted pressure sump, steel Conforms to the requirements according to DIN VDE 0185-305 (IEC 62305) OBO Type no : 249 8-10 ST-OT (5311 50 3)

Providing and insttalling of flat conductor holder suitable for FL 30. Installed with 2 hexagonal bolts. OBO Type No. 166 LS 70 ( 5226570 )

Supply and installation of UL Listed & CPRI Tested maintenance free ,Low carbon copper coated earth rod of 3 metre electrode having diameter of 14mm with copper coating thickness of 250micron tested as per IEC 62561-2 . OBO Type No. 14 3000 CCER(5450010)

Supply and installtion of Universal clamp made of SS to connect rod with flat conductor . OBO Type No. 14 25 RTC(5450066)

Supply and installtion of Earth conductivity enhancing compound shall be of 25 kg/pit tested as per IEC 62561-7,TCLP tested. OBO Type No. OEC 2 25(5450058)

The above arrangements shall be provided with Heavy duty earth champer of 5000kg load bearing capacity to ensure the safety of earthing system . OBO Type No.UFE(5450030).

Supplying, erecting, testing and commissioning of 14HP, VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100% capacity at 47° C, non stop cooling even at 56° C and coefficient of performance (COP) 3.00 to 4.00, modular type vertical hot air discharge suitable for longer piping range upto 1000 metre operation in cooling mode with inverter/digital VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete.

Supplying, erecting, testing and commissioning 16 HP VRF / VRV air conditioning system, out door unit (ODU) complying type-IV OEM standards working on HFC free refrigerant R410A or other required/suitable green equivalent refrigerant, for cooling capacity delivering 100% at 47 deg. celcius and non stop cooling even at 56 deg. celsius and coefficient of performance (COP) 3.00 to 4.00, modular type horizontal/vertical hot air discharge suitable for total piping length upto 1000 metre operation in cooling mode with inverter based VRF/VRV technology microprocessor based control compressor starter/control panel complete with scroll compressor, air cooled anti corrosive copper condenser coil of suitable shape for increasing maximum heat transfer area, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V ± 10%, 50 Hz, 3 phase power supply, internal copper refrigerant piping, internal wiring and first charge of refrigerant, etc. all housed in powder coated weather proof cabinet.

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette room/indoor unit (IDU-compact / standard size) of nominal cooling capacity 2.8TR ( 1100 cfm ) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anti corrosive coating suitable for coastal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation.

Supplying and installation of high pressure grade required size copper connection Y or T- Joints / refnet for Outdoor unit liquid and suction line complete erected on wall/ceiling with supports/raceways, Nitrile rubber insulation, painting etc. with brazing and testing for leakages confirming the normal operation of the VRV / VRF air conditioning system.

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette room/indoor unit (IDU-compact / standard size) of nominal cooling capacity 4.0TR (1218 cfm ) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anti corrosive coating suitable for coastal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation.

Supplying and installation of high pressure grade required size copper connection Y or T- Joints / refnet for Indoor unit liquid and suction line complete erected on wall/ceiling with supports/raceways, Nitrile rubber insulation, painting etc. with brazing and testing for leakages confirming the normal operation of the VRV / VRF air conditioning system.

supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 6.4mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultraviolet radiations with OEM standards of VRV/VRF air conditioning system comple (Pipe sizing to be Verified as per OEM standards and invoiced as per actual measurement.)

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 9.5 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system. (Pipe sizing to be Verified as per OEM standards and invoiced as per actual measurement.)

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 12.7 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system. (Pipe sizing to be Verified as per OEM standards and invoiced as per actual measurement.)

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 15.9 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system (Pipe sizing to be Verified as per OEM standards and invoiced as per actual measurement.)

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 19.1 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system (Pipe sizing to be Verified as per OEM standards and invoiced as per actual measurement.)

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 22.2 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system (Pipe sizing to be Verified as per OEM standards and invoiced as per actual measurement.)

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 28.6 mm dia (OD) for liquid line / suction line supply and return piping (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system. (Pipe sizing to be Verified as per OEM standards and invoiced as per actual measurement.)

Supplying and erecting PVC conduit 40 mm dia. with PVC accessories on ceiling/ wall with 10 mm thick elastomeric nitrile rubber along with application of multicoating for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system. (Pipe sizing to be Verified as per OEM standards and invoiced as per actual measurement.)

Supplying and erecting PVC conduit 32 mm dia. with PVC accessories on ceiling with 10 mm thick elastomeric nitrile rubber along with application of multicoating for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system. (Pipe sizing to be Verified as per OEM standards and invoiced as per actual measurement.)

Supplying and erecting PVC conduit 25 mm dia. with PVC accessories on ceiling with 10 mm thick elastomeric nitrile rubber along with application of multicoating for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system. (Pipe sizing to be Verified as per OEM standards and invoiced as per actual measurement.)

Supply and erecting Electric control and communication cable between indoor and outdoor unit with elctric conduit pipe, fittings. (Cable Type and sizing to be Verified as per OEM standards and invoiced as per actual measurement.)

SITC of Electric Traction Passenger Lift with · · ·

Rated capacity :- 8 Passenger/544Kg

Floors :- G+1 floor (2 Stops/2 Landings)

Travel :- 3 to 4.2 mtrs · ·

Rated speed :- 1.0 mps VS

Location of Lift Machine:- MR/MRL

Car/Landing door clear opening of 800 mm wide x 2000 mm high, Clear Car size of 1850 mm wide x 1770 mm deep x 2250mm high ,Lift shaft available having clear size of ......mm wide x ......mm deep,......mm Pit depth, ………mm Overhead.

Doors type :- COPO/TOPO Doors with frame made from SS 304 grade solid(non-cladded) sheet of 1.5mm thick in hairline finish for car and all landing doors with SS door architraves/frames The lift doors shall have minimum 1 hour fire rating (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory).

Lift car enclosure made from SS 304 grade solid (non-cladded) sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with ecessary false ceiling with adequate LED lights, lower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. The lift car interior design shall be done as per the directions of engineer in charge.

COP with SS face plate having metallic push buttons with Braille code & luminous indicator around button with FPI, scrolling UP/DN LED indicator &with / without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor

LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings.

Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port. The controller shall have necessary protections such as overcurrent, overvoltage, over speed, overheat for all devices including lift motor and travel direction protection, protection for phase loss at input or output etc. various operation modes such as maintenance, change direction by attendant, full load bypass, VIP call operation, self levelling operation, call cancel facility, auto return to home landing, fireman evacuation operation, earthquake operation, door open/close operation from COP etc. The system can record information for minimum 30 latest faults, with real-time clock management and handheld keypad with LCD screen for view and setting of parameters. The control panel duly wired with proper size & strength, copper wire for power & control circuit, with provision for addition of floor/control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class.

ARD complete with necessary SMF VRLA batteries.

Fireman controller having fireman switch at fire Landing

CCTV surveillance system comprises of 2 nos minimum 2.0 MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with NVR kept in LMR/FCC with HDR data backup min. 90 days with min. 18” FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge.

Lift Machine of Gearless PMSM of suitable kW with duty cycle of minimum 120 starts/hr (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory), with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on LMR floor/ shaft walls complete with main/diverter traction sheaves, suspension wire ropes/belts of adequate size & strength.

Other mechanical parts such as 'T' section adequate size guide rails for car & counter weight with brackets fasteners, counter weight frame with necessary blocks, buffers with necessary support arrangement, MS pit ladder etc. erected with necessary steel work.

Minor civil work such as alteration work if any necessary for erection of landing door frames and it's accessories e.g. sill, header, hole pass etc complete with plaster finish, civil work for erection buffers, erection of lift machinery, adequate size core cuts if required & scaffolding for erecting guide rails, providing and fixing steel girders/RCC work having adequate strength for mounting and hoisting lift machine etc. complete as per specification no. LFT

General: - Job includes entire procedure of obtaining all necessary erection permissions & "License to Work the Lift" from Electrical Inspector(Lifts) with submission to the Engineer In Charge. The above rate includes Fully Comprehensive AMC for one year from the date of commissioning.

The above rate includes Fully Comprehensive AMC for one year from the date of commissioning

For Lift having 800mm wide x 2000mm high clear entrance in 1.5mm thick SS 304 grade solid (non-cladded) landing door [Two panel], this includes all necessary accessories like LOP's with UP/DN buttons-arrows-indicators,extension of guide rails, shaft wiring with trunking, traveling cables, main hoisting ropes/belts, & OSG rope landing doors with all accessories etc. necessary for the normal safe functioning of lift installation complete.(ONE FOR EACH LIFT)

for Additional 2MP camera with necessary accessories at Home landing