PROVN OF FUEL OIL AND LUBRICANT STORE NEAR BUILDING NO P312 AND PROVN OF HARD STANDING WITH OVERHEAD SHED AT BLDG NO P464 OF BATTALION MANDIR IN INF BN NO 2 AT BRICHGUNJ MIL STN PORT BLAIR

Amount

Surface dressing not exceeding 15cm deep in hard/dense soil complete all as specified and directed.

Excavation over areas, not exceeding 1.5m deep and getting out in hard/dense soil complete all as specified and directed.

All as per item No.2 here in before but for each additional 1.5m or part thereof in depth beyond the first 1.5 m and getting out Hard/Dense Soil.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in hard dense soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50m and depositing where directed. at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L Cement concrete in foundations, filling in and mass concrete type D-2 1:4:8 (using 40mm graded stone aggregate) complete all as specified and directed.

M&L Reinforced cement concrete (Design mix M-30 grade using 20mm graded stone aggregate) as in Foundations footings, plinth beams, bases for columns, etc complete all as directed.

M&L Reinforced cement concrete (Design mix M-30 grade using 20mm graded stone aggregate) above top of footings including attached pilasters and buttresses complete all as directed.

M&L Reinforced cement concrete (Design mix M-30 grade using 20mm graded stone aggregate) Columns, pillars, piers, posts and struts complete all as directed.

M&L Reinforced cement concrete (Design mix M-30 grade using 20mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span omplete all as specified and directed.

M&L Reinforced cement concrete (Design mix M-30 grade using 20mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified and directed.

Use and waste of Formwork flat or curved to sides of concrete foundations, footings, bases of columns, and plinth beams and similar work vertical or to batter omplete all as specified and directed.

M&L Formwork flat or curved to to sides of pillars, posts, struts, piers, columns and stanchions omplete all as specified and directed.

M&L Formwork flat or curved to sides and soffits offloor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelvesincluding sup- ports, overhangs, etc. also splays between floors and beams, etc. omplete all as specified and directed.

M&L Formwork flat or curved to Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) omplete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F Mild steel TMT bars 5 to 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L pre-cast cement concrete masonary in PCC 1:3:6 type C1 using 20mm graded coarse aggregate with solid block, exceeding 10cm in width setting in CM 1:6 complete all as specified and directed.

M&L for 40mm thick Damp proof course in cement concrete 1:2:4 type B-O using 12.5mm graded stone aggregate to horizontal or vertical surface including necessary formwork complete all as specified and directed.

M&L for 15mm thick rendering in two layers of 10mm thick backing coat in CM 1:6 and 5mm thick floating coat in CM 1:4 mixed with water proofing compound on all external wall surfaces/ RCC roof surface complete all as specified and directed.

M&L for 10mm thick rendering in CM 1:6 on all internal wall surfaces complete all as specified and directed.

M&L for rendering 5mm thick in CM 1:3 on soffits of RCC slabs, roof projections, soffits and sides of RCC beams, waist slab, Loft Slab, RCC shelves, Chajjas, and the like complete all as specified and directed.

M&L for sand Filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 10cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L 100mm thick PCC 1:4:8 Type D-2 using 40mm graded coarse aggregate as in sub base for floors complete all as specified and directed.

M&L 40mm thick Cement concrete type B-1,1:2:4 using 20mm graded coarse aggregate as in plinth protection complete all as specified and directed.

M & L for 40mm thick PCC 1:2:4 type Bo (using 12.5mm graded stone aggregate) as in floors including finishing even and smooth using extra cement complete all as specified and directed.

M& L for two coat of wheather proof exterior acrylic emulsion paint with anti fungal property over a coat of primer over and including 2mm thick externall wall care putty on newly plastered wall surfaces including preperation of surfaces etc complete all as specified and as directed.

M & L for applying two coats of oil bound distemper over a coat of primer over and including 2 mm thick wall putty on newly plastered surfaces of wall including preperation of surfaces complete all as specificed and as directed

M & L for applying two coats of oil bound distemper over a coat of alkali resistant primer over and including 2 mm thick putty on newly plastered surfaces of Ceilings, soffits of RCC slabs, roof projections, soffits and sides of RCC beams, waist slab, Loft Slab, RCC shelves, Chajjas, and the like including preperation of surfaces complete all as specificed and as directed

S&F Aluminium anodised door / window / ventilator / partition frames including shutters (Two no glazed and gauzed) side hung type with out sash bar, standard aluminium grill, using standerd section incl necessary joining cleats glazing clips, rubber packing, anodise Aluminium snap beading screws, handle and locking arragment etc complete Note : Glass & fly proof mesh measured and paid seperately as supply only & Hardwares shall be measured and paid separetely

S&F 150mm long extruded aluminium alloy anodised handles fabricated type complete all as directed

S&F 100mm long extruded aluminium alloy anodised handles fabricated type complete all as directed

S& F Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) 300 mm long and fixing clips to sheet cast or extruded sections and fixing bolt or cast aluminium alloy complete all as directed

S&F Aluminium anodised barrel tower bolt of extruded section of size 150mm long complete all as directed

S&F Aluminium anodised barrel tower bolt of extruded section of size 100mm long complete all as directed

Supply only 4 mm thick sheet glass ordinary quality and glazing with rubber packing around the glass, in squares not exceeding 0.50 sqm in each pane complete all as specified and as directed.

S&F Aluminum anodised butt hings 75mm long extruded alluminum, alloy with galvanised mild steel hinge pin, type C-22 complete all as directed

Supply only 12 mm thick Prelaminatd particle board, exterior grade, prelaminated exterior grade on both sides with decorative choice lamination and fixed to aluminium frames complete all as specified and as directed.

S & F for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachemtns attachmentcomplete all as directed

S & F for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as directed

Preparation of new or previously untreated steel surfaces & applying a two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer over 10cm in width or girth,not otherwise described.

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified.

S & F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified.

M&L for glazed, polished Chequered cement concrete tiles 300mm x 300mm x 25mm thick, set, jointed and pointed in neat cement slurry, including screed bedding layer in cement mortar 1:6, 20mm thick in flooring complete all as specified and as directed by Engr-In-Charge

M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement.

S & F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe-410-W(Gde-E-250) quality-B

S&F mild steel flat iron 40 x 3mm as in wind tie including all necessary drilling, bolting or riveting etc., confirming to Fe 290.

S & F for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment (Fe 410-W, Gde-E250, Quality-A)

S&F Mild steel bolts exc 12mm not exc 20mm dia , purpose made, with hexagonal or square head one end and screwed the other, or screw both ends; each screwed end to be fitted with washers and one hexagonal or square nut, exc 30cm long

S&F 110 mm PVC (SWR ) pipes single socketed in any length with rubber ring joints fixed to walls for rain water pipe

S&F as in aluminium anodised snap grid frame work (size of grid 605x605mm) with 35x25x1.5mm main tee and 25x25x1.4mm, cross tee and wall angle for false ceiling and suspended with 6mm dia GI wire, hooked to roof with needful adjustement up to 1200mm long by means of ceiling cleats made out of GI Flat 40 X 3mm 60mm long and expansion holdfasteners 12.5mm dia 40mm long, including dismantling celing board of any description and any type fixed to the aluminium frame work with screws or nails etc complete all as specified and as directed by Engineer -in-Charge.

Fixing only Eco board 600 X 600 X 4mm thick decorative type fixed to the aluminium frame work with screws or nails etc including two coats of oil bound distemper over a coat of primer complete all as specified and as directed. Note :- Eco Boards obtained from item No.5 to be re-used

Non -skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but n.exc 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for PCC 1:3:6, type C2, (Using 40 mm graded stone aggregate), 150 mm thick as in plinth protection/Sub base flooring, finishing surface fair and even, in panels & filling joints with mortar, etc., complete all as specified and directed.

S & F 25mm dia bore unplasticised PVC pipes of pressure rating 10kgf/cm with all fittings and fixed complete to walls and ceilings or laid in floor etc complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks 500 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

M & L for two coats of oil bound distemper over on coat of alkali resistant primer including preparation of newly plastered surfaces of wall complete all as specified and as directed

M & L for two coats of wheather proof exterior acrylic emulsion paint with anti fungal property over a coat of primer on newly plastered surfaces of wall including preparation of surface etc complete all as specified and as directed.

M & L For Point wiring complete with proper colour coading using, 1100 Volts grade, 1.5 Sqmm, PVC insulated FRLS, unsheathed wire with multi stranded copper conductor confirming to IS-694, Part II, ISI marked and including PVC conduit with ISI marked with all accessories in wall/celling/floor/roof etc, sunk pressed steel not less than 2 mm thick, 50 mm deep terminal boxes with 3mm thick ISI marked plastic laminated sheet top cover fastended with chromium plated brass screws including 1.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts Multistranded copper conductor green colour as continuous earth wire connected to common earth dolly all as specified and directed for the following:- (a) One light Point controlled by one switch

(b) One ceiling fan point controlled by one way switch

Supply and fix Switch piano, flush button, single pole, ISI marked, one way 5 Amps 240 volts .complete all as specified and as dircted by Engineer-in-Charge

Supply and fix ceiling rose surface baklite 65 x 50 mm 3 terminal, complete all as specfified and as directed by Engineer-in-Charge

Supply and fix fan speed regulator, electronic suitable for single phase AC, 240 volts, 50 Hz,100 watts, complete all as specified and as directed by Engineer-in-Charge

Supply and fix energy efficient LED Smart bright batten 22 watt fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core shethed cable from fitting to ceiling rose all as specified and as diected.

Supply and fix ceiling fan suitable for working on AC 230 volts, 50 Hz,1200 mm sweep 5 star rating with down rod and canopy colour of milky white including suitable fan hook anchor flashner for fixing of fan on ceiling complete all as specified and as directed.

Supply and fix metal enclosure distribution board SPN, 4 way 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs, complete all as as specified and as directed.

Supply and fix MCB single pole, 240 volts, 5 to 32 Amps, with rupturing capcity 10KA all as specified and as directed.

Supply and fix MCB SPN 240 volts, 5 to 32 Amps,with rupturing capcity 10KA all as specified and as directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground ( earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part - I

Supply, lay, test and commissioning under ground XLPE insulated and PVC sheathed, armoured heavy duty under ground cable, suitable for earthed system, laying in trenches/duct sleeving through pipe in duct, ISI marked with aluminium stranded conductor 1100 volt grade of cross section area 2 Core 10 Sq mm.

Supply & lay cable protection pipe of HDPE double wall corrugated (DWC) incl couplers,bends etc of size 50 mm OD and ID 38mm confirming to IS 14930 -II and ISI Marked all specified and directed.

S&F tube light grade galvanised with all fittings laid in trenches of following size. (a) 50 mm dia bore.

Material and Labour for cutting bituminous road at a width not more than 30cm and a depth not exceeding 60 cm for laying of pipes on road crossing for cable protection and making good with cement concrete 1:2:4, type, B-2 to match the existing surfaces of the road all as specified and as directed by Engineer in charge.

P Babu

S K ENTERPRISES

CHANDER SEKER ENTERPRISE

Nirman Construction Company

DEEPAK AGENCIES

RPG AND COMPANY

MAJUMDAR FURNITURE