ADDITION /ALTERATION TO BUILDING Nos P-35, P-39 AND P-53 AT ICGAS CHENNAI(SPECIAL ITEM OF WORK)

Amount

Taking down chowkats (or) frames of any description with shutters (without taking off shutters from the frame) of area not exc.1.5 sqm each along with fittings including separating guard bars/grills/ wire mesh etc., and making good the disturbed surfaces of wall to match with existing adjoining surfaces complete all as specified and as directed.

Taking down chowkats (or) frames of any description with shutters (without taking off shutters from the frame) of area exc.1.5 sqm and not exc. 4.0 Sqm each along with fittings including separating guard bars/grills/ wire mesh etc.,and making good the disturbed surfaces of wall to match with existing adjoining surfaces complete all as specified and as directed.

Taking down shutters of any description exc 1.00 Sqm and not exc. 2.00 Sqm each complete all as specified and as directed.

Resecuring or easing & adjusting shutters exceeding 1.00 Sqm not exceeding 2sqm each and refixing in same opening after cutting, easing and adjusting and refixing builders hardware as required including renewal of unserviceable builders hardware article and screws etc., complete all as specified and as directed.

Demolition of reinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness. (Below or above ground level) complete all as specified and as directed.

Material and labour for Mild steel TMT bars in reinforcement, 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-500D all as specified and as directed.

Material and Labour for reinforced cement concrete of M 25 ( 20mm graded stone aggregate as in slabs supported on walls, beams and columns floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as directed. Note: Reinforcement shall be measured & paid separately.

Material and Labour for Form work to flat surface of soffits of suspended slabs such as roof slab floor slab, landings and similar work not exc 200 mm thick all as directed by Engr - In Charge.

Dismantling of ordered portions of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc., separation of serviceable materials from the unserviceable, stacking the serviceable materials within 100 M and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 500 M as directed by the Engineer in Charge.

Material and labour for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and as directed..

Material and labour for Brickwork with fly ash bricks, straight or curved on plan to any radius in half brick wall , built in cement mortar 1:4 complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed.

Material and labour for rendering in Cement Mortar 15mm thick in two coats, i.e, in Cement Mortar 1:4, 5mm thick mixed with water proofing compound as per manufacturers' instructions over in Cement Mortar 1:6, 10mm thick on fair faces of brick/concrete surfaces, finished even and fair externally complete all as specified and as directed. Note: WPC will be measured and paid separately.

M & L for Rendering 15mm thick in cement plaster 1:4 on other than fair faces of brick work or concrete surfaces finished even and smooth with out extra cement

Material and labour for 5mm thick rendering in cement mortar 1:3 on concrete surfaces, finished even and smooth without using extra cement as in ceiling chajja complete all as specified and as directed.

Demolition of floor hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises to out side MD land etc., complete all as specified and as directed.

Material and labour for coloured Vitrified Ceramic tiles of grade B-I (a), 9-10 mm thick (square/ rectangular) polished, light shade, area of each tile exceeding 0.36 Sqm and not exceeding 0.42 Sqm, laid in floors of pattern as approved over and including 15mm thick screed bed in Cement mortar 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and as directed. Note :- (i) Quoted rate shall deem to be included cost of screed bed. (ii) Before executing of Tiles work ATT Will be done and ATT will be measured and paid separately

Material and labour for coloured Non Skid ceramic tiles, matt finish of grade B-II(a), 7 to 8 mm thick (square/ rectangular), light coloured group, area of each tile exceeding 0.18Sqm but not exceeding 0.38 sqm,fixed in vertical surfaces such as in skirting/dado as approved over and including 15mm thick screed bed in Cement mortar 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified and as directed. Note :- (i) Quoted rate shall deem to be included cost of screed bed. (ii) Before executing of Tiles work ATT Will be done and ATT will be measured and paid separately

Material and labour for glazed coloured ceramic tiles of grade B-III, 7mm thick of size 450mm x 350mm or 450mm x 300mm or of size matching to floor tile as approved by GE, fixed in vertical surfaces such as in skirting/dado set and jointed in neat cement slurry and pointed in white or coloured cement to match floor tile over and including a backing coat in Cement Mortar 1:4, 10mm thick all as specified and as directed.

Material and labour for 16-18 mm thick machine cut, Granite stone slab (Jet/Z black type) (table rubbed and polished) in platforms and like in cement mortar 1:4 bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types and making mould on edges & including cutting of three numbers of grooves etc complete all as specified and directed

Material and labour for Green marble18- 20mm thick (table rubbed and polished) in steps, window- cills, cooking platforms, verandah including nosing and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble over and including screed bed of 15mm thick cement mortar 1:4 complete all as specified and as directed.

Material and labour for Green marble 18- 20mm thick (table rubbed and polished) in vertical surfaces such as edges of platforms, jambs, pillars etc., including nosing and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of marble over and including a backing coat of 15mm thick in cement mortar 1:3, complete all as specified and as directed.

Supply and Fix Solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as per specification & drawing shown in MES schedule part II complete all as specified and as directed.

Supply and Fix Factory made PVC Solid panel door shutters 30mm thick (style) solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin) consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail Paneling of plain colour PVC sheet to be fitted in the mild steel frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement supply and fixing in the frame at site as per specification and drawings shown in MES schedule part II complete all as specified and as directed.

Supply and Fix pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., complete all as specified and as directed.

Supply and Fix pressed steel fames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., complete all as specified and as directed.

Material and labour for Plain Cement Concrete in 1:2:4 mix, type B0, using 12.5 mm graded granite stone aggregate as in cast in situ in lintels up to 1.5 M sqan, cills and other similar bands, plinth courses, parapets, copings, bed plates and the like including necessary formworks complete all as specified and as directed.

Supply and Fix 30mm thick Flush shutters, solid core construction, with particle board core and plywood face panels and both faces are covered with decorative face veneer with lipping / frame to match on both sides and fitted to chowkats complete all as specified and as directed.

Supply and Fix 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass gauze,etc (without sash bars),edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR part-I section 8 clause 8.24(a) fitted to chowkat complete all as specified and as directed.

Supply and fix powder coated aluminium door having thickness of powder coating not less than 50 micron and colour as approved by GE, using aluminium section weighing not less than 0.55 Kg/m for frame work and 0.48Kg/m for shutters, including glazed with 5.0 mm thick tinted glass on top pane, 12mm thick exterior grade prelaminated particle boards on bottom pane, slide or fix type powder coated aluminium mosquito proofing shutters with aluminium alloy wire mesh, additional sliding track and necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, star lock, interlocking handles for fly proof shutters, hinges, powder coated aluminum snap beading, screws etc. complete all as specified and as directed. Note: Measurement shall be the size of opening and the unit rate quoted shall be deemed to include the cost of Powder coated Aluminium sections for frames, shutters, jointing cleats, particle boards, sheet glass & wire mesh, glazing clips, builders hardware etc.

Supply and fix Powder coated Aluminium window (side hung and top hung shutters for window AC opening) having thickness of powder coating not less than 50 micron and colour as approved by GE, using aluminium sections weighing not less than 0.55 Kg/RM for frame work and 0.48 Kg/RM for shutters fixed with sash bars including glazed shutter and wire gauged fly prof shutters, 5.0 mm thick tinted glass fixed with glazing clips and rubber packing and aluminium alloy wire mesh fixed with necessary jointing cleats, powder coated aluminium snap beads, screw, builders hardwares like hinges, handles, peg stays, tower bolts etc., complete all as specified and as directed. Note: Measurement shall be the size of opening and the unit rate quoted shall be deemed to include the cost of Powder coated Aluminium sections for frames, shutters, jointing cleats, sheet glass, aluminium alloy wire mesh, glazing clips, builders hardware etc.

Supply and fix Powder coated Aluminium three track sliding windows with fly proof shutters using aluminium section weighing not less than 0.55 Kg/RM (size of frame 100mm) for frame work and 0.48 Kg/RM for shutters fixed with sash bars, powder coated aluminium snap beads, screws including three sliding shutters, two fully glazed shutters with 5.0 mm thick tinted glass fixed with glazing clips and rubber packing and one wire mesh shutter with aluminium alloy wire mesh, fixed with necessary jointing cleats powder coated aluminium snap beads, screw, roller interlocking handles etc., complete all as specified and directed. Note: Measurement shall be the size of opening and the unit rate quoted shall be deemed to include the cost of powder coated Aluminium sections for frames, shutters, jointing cleats, sheet glass and wire mesh, glazing clips, builders hardware etc.

Supply and fix Powder coated Aluminium side hung window/ventilators having thickness of powder coating not less than 50 micron and colour as approved by GE, using aluminium sections weighing not less than 0.55 Kg/RM for frame work and 0.48 Kg/RM for shutters fixed without sash bars including glazed shutter fixed with glazing clips and rubber packing and aluminium alloy wire mesh fixed with necessary jointing cleats, powder coated aluminium snap beads, screw, builders hardwares like hinges type B-21 100mm long - 2Nos, 150mm long D type handle - 1 No, tower bolt 150mm long - 2 Nos, Peg stay 150mm long - 1 No for each shutters etc., complete all as specified and as directed. Note: (i) Measurement shall be the size of opening and the unit rate quoted shall be deemed to include the cost of Powder coated Aluminium sections for frames, shutters, jointing cleats, glazing clips, builders hardware etc. (ii) Glass panes to windows/ventilator shall be measured and paid separately under relevant item.

Supply and Fix Powder coated aluminium grill having thickness of powder coating not less than 50 micron and colour, design/pattern as approved, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved powder coated aluminium standard section around the opening etc., complete as per requirement and direction of Engineer-in-charge.

Supply and Fix plain sheet glass pane, 5.5mm thick, ordinary quality and glazing with neoprene rubber / wooden beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Supply and Fix 40mm thick solid PVC sandwich panel for partitions with 2 mm thick printed PVC sheet on both sides suitably fixed in M S angle frame work as per specifications complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing aluminium anodised partition (area of panel not exceeding 1.5 Sqm each) with frame of size 100mmx40mmx1.55mm thick, fixed with hold fasts, snap beading, rubber gasket including 12mm thick prelaminated (both side decorative) particle board exterior grade and 4mm thick frosted glass panes complete all as specified and as directed.

Supply and Fix plain sheet glass pane, 4.0mm thick, figured glass, pin head type and glazing with neoprene rubber / wooden beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Supply, fabricate and fix Mild steel framed work such as gates and grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290, Gde E-165 all as specified and directed.

Supply and Fix Butt hinges of size 100mm, cast brass, type C-22 with mild steel hinge pin, bright polished and fixed complete all as specified and as directed.

Supply and Fix Butt hinges of size 75 mm, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed all as specified and as directed.

Supply and Fix Aluminium anodised, ISI marked barrel tower bolts 200mm of extruded section and fixed complete all as specified and directed.

Supply and Fix 300 mm long Aluminum alloy anodised, sliding door bolt with hasp and staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy all complete as specified and as directed. .

Supply and Fix extruded aluminium alloy handles fabricated types, anodised, each 100mm long complete all as specified and directed.

Supply and Fix extruded aluminium alloy handles fabricated types, anodised, each 150mm long complete all as specified and directed.

Supply and fix 18mm thick and 600 density Wood Polymer Composite (WPC) prelaminated sheets water proof, termite proof, borer proof and corrosion free with melamine finish decorative shade as approved by GE on both sides of board as in Cabinet unit and over head unit (Modular type) and fixed all as per manufacturers instruction including all fittings and fixtures such as soft closing hinges, lock, knobs etc., complete all as specified and as directed. Notes: (i) Any damages caused to the existing structure shall be made good without any extra cost . (ii)The rate quoted by the tenderer shall be inclusive of the above provisions.

Supply and fix 0.40 mm thick Decorative laminate, type-1 of surface finish, colour and pattern as approved, fixed with approved synthetic rubber adhesive as per manufacturer's instructions complete all as specified and as directed.

Supply and fix 0.80 mm thick Decorative laminate, type-1 of surface finish, colour and pattern as approved, fixed with approved synthetic rubber adhesive as per manufacturer's instructions complete all as specified and as directed.

Supply and Fix continuous piano hinges mild steel bright finish or electrogalvanised Width of flap (when open) 30mm complete all as specified and as directed.

Supply and Fix mortice lock, vertical type, size 150mm with door handles, 4 lever mechanism lock set with Latch bolt suitable for Left and right hand, inside and outside opening doors, 25 mm to 45 mm thick with two numbers of keys complete all as specified and as directed.

Supply and Fix brass cupboard locks grade I, 4 lever of size 65mm complete all as specified and as directed.

Supply and Fix Floor door stopper, 140mm overall length of cover plate of brass body and tongue with hard drawn steel spring, fixed in floor all as specified and as directed.

Supply and Fix aluminium wardrobe hooks (single) 50mm to 60mm complete all as specified and as directed.

Supply and Fix 40mm dia, cupboard knobs fixed with nut, screw and washer of brass polished complete all as specified and as directed .

Supply and Fix in repairs plain sheet glass pane, 4.0mm thick, ordinary quality and glazing with neoprene rubber / wooden beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Supply and Fix in repairs 25mm external dia stainless steel decorative designer curtain rod (drapery rod), fancy type made out of stainless steel tube, standard quality of grade AI SI-304, polish finish of wall thickness not less than1.5mm including one pair of designer lattos and brackets and taking out old pelmet with curtain rods complete all as specified and as directed. Note: One run of 25mm dia SS curtain rod along with one pair of bracket shall be considered as one unit length.

Supply and Fix stainless steel wire mesh with aperture not exc 1.40 mm dia and of wire 0.36 mm and fixed with existing/new wooden beading staples including painting to beading etc complete all as required and directed.

Supply and Fix in repairs stainless steel wire mesh with aperture not exc 1.40 mm dia and of wire 0.36 mm and fixed with existing/new wooden beading staples including painting to beading etc. complete all as required and directed.

Material and labour Preparing new surfaces of wood and wood based surfaces of any description, not other wise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Material and labour Preparing new surfaces of steel of any description, not other wise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat red oxide / zinc chrome primer complete all as specified and as directed.

Taking down steel tubing of 15mm bore pipe and connections including removing from site all as specified and directed .

Taking down steel tubing of 20mm bore pipe and connections including removing from site all as specified and directed .

Supply and fix Galvanised steel water tubing medium grade 15mm bore conforming to IS specifications and ISI marked with all fittings such as bends, tees, unions, elbows, connecting pieces, plugs, sockets etc. fixed on walls, concealed in walls/ceiling or laid in floors etc., complete all as specified and directed.

Supply and fix Galvanised steel water tubing medium grade 20mm bore conforming to IS specifications and ISI marked with all fittings such as bends, tees, unions, elbows, connecting pieces, plugs, sockets etc. fixed on walls, concealed in walls/ceiling or laid in floors etc., complete all as specified and directed. Note for items No.62.00 & 63.00 : (i) The unit rate shall be deemed to inclusive of all GI fittings such as bends, elbows, short piece connections, back nuts, caps plugs and unions etc., of medium grade and jointing material. (ii) Cutting chases for concealing pipe in walls shall be measured and paid separately.

Cutting chases in brick walls pinning in, making good to facings with cement mortar 1:3 for concealed water tubing or similar works and making good, cutting not exc 10 cm girth all as specified and directed by the Engineer-in-Charge.

Supply and Fix Gun metal globe or gate valve of size 25mm bore confirming to IS 778-1984 with brass spindle and iron wheel head at the top screwed both ends for GI pipe including all fittings / fixtures like nipple, union etc., including taking down the existing gate valve complete all as specified and as directed

Supply and Fix in repairs Vitreous china white squatting pan 'Orissa' pattern of size 630mm x 450 mm or next higher size with integral foot rests provided over lime concrete bedding including 100 mm bore PVC (SWR) ‘P’ or ‘S’ trap of suitable size for connecting WC to branch piece with cement joints and making good disturbed surfaces of flooring etc. and including PVC low level cistern of 10L capacity including bracket joint and flush pipe, PVC connection (600X15mm) flushing pipe complete all as specified and as directed.

Supply and fix in repairs Vitreous china wash down water closet pan, pedestal pattern, floor mounted, colour white with all fittings including fixing bolts, flush pipe, Plastic water closet seat, white, closed pattern with flat bottom and cover with mild steel chromium plated or aluminised hinging device (excluding flushing cistern) and P/S trap including connections to drain (or outgoing pipe) and taking down existing water closet etc., complete all as specified and as directed.

Supply and fix in repairs PVC low level flushing cistern, white, 10 litre capacity, syphonic action type, white body with inlet, ball valve, float, handle, bracket, 32mm bore steel chromium plated flush pipe etc. and connecting to WC and water pipe lines etc., complete all as specified and as directed.

Supply and fix in repairs vitreous China urinal, half stall type complete including waste pipe, flush pipe & providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement etc., and including connection to flushing pipe and outgoing pipes fixed in repairs complete all as specified and as directed.

Supply and Fix Health faucet (ABS Body) chromium plated suitable for 15 mm dia pipe with 1.00 metre long flexible tube 8mm dia (PVC chromium plated) and ABS wall hook including making connections and fixed in position complete in all respect as specified and as directed.

Supply and fix Soap dish brass chromium plated fixed with and including chromium plated brass screws with wooden plugs complete all as specified and as directed .

Supply and fix in repairs CP Toilet paper holder with flat recessed complete all as specified and directed.

Supply and Fix 15mm bore Bib cock of cast copper alloy, fancy type, Chromium plated with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

Supply and fix two way bib cock, brass Chromium plated suitable for hot & cold water all as per Cat No.ARI 39041 of Jaquar or G4834A1 of Parryware or Astro-6312N of Prayag or techno-commercially equivalent of other specified makes complete all as specified and as directed.

Supply and Fix 15mm stop cock, cast copper alloy with crutch or butterflty handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated with fancy shank and cup complete all as specified and as directed.

Supply and fix in repair 15mm bore pillar tap fancy type, cast copper alloy with capstan heads, chromium plated screwed down, high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipes complete all as specified and as directed.

Supply and fix in repair Brass chromium plated shower rose of size 125mm with or without swivel joints fixing to 15mm dia steel pipe or union complete all as specified and as directed.

Supply and Fix PVC Connection pipe, 600mm long, heavy duty with two sets of brass nuts & washers (one at each end) etc suitable for 15mm bore of pipe as in repair complete all as specified and as directed.

Supply and Fix 600mm long towel rail of PTMT fixed to wall with steel screws and PVC rawl plug as in repair complete all as specified and as directed.

Supply and Fix 100 mm dia CI sand cast soil waste and vent pipes in any length with or without ears with cement joints laid in trenches or in floors/fixed to wall or dia in repairs complete all as specified and as directed.

Supply and fix in repairs 20mm bore Ball valve PTMT with epoxy coated aluminimum rod and reducer for 25 to 20mm bore pipe, weight not less than 210gms, high pressure with polyethylene high density float and complete screwed for iron pipe all as specified and directed.

Supply and Fix in repairs, 1000 litres capacity Rotational Moulded Polyethylene (HDPE) FDA grade materials water storage tanks, three layered (Cylindrical vertical with closed top) screwed lid type conforming to IS 12701-1996 with manhole lid and suitable locking arrangement, making holes for inlet, outlet, washout and over flow pipes, hoisted and fixed in position as specified in SSR Part- I (2009) including disconnecting and fixing existing GI fittings and pipe complete all as specified and as directed.

Material and Labour for 100mm bore dia cast iron floor trap with CP grating, with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1all as specified and directed.

Supply and fix CP grating doom grating doom 100mm/ 110mm dia complete all as specified and directed.

Supply and Fix in repairs110mm bore PVC (SWR) pipe of pressure 6 Kg/Sqcm fixed in wall, ceiling, in any length with rubber ring joints, fixed to wall including distance pieces and stack clamp with nuts & bolts complete all as specified and directed.

Supply and Fix 110mm bore, PVC (SWR) bends any radius complete all as specified and as directed..

Material and labour for Preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed.

Material and labour for preparation of old surface of ceiling and applying one coat of white wash complete all as specified and as complete all as directed.

Material and labour for preparation of old painted surfaces and applying one coat of synthetic enamel paint on wooden surfaces of any description not other wise described over 10 cm width or girth etc. complete all as specified and as directed.

Supply and fix in repair vitreous china counter wash hand basin snow white of size 560mmx470mm as per Cat No. 1005A of CERA or equivalent model (same size / next higher size) of other makes specified in particular specifications including supply and fixing of 20mm thick telephone black machine polished granite slab in single piece of minimum size 900 mm x 600mm with necessary cutting and bevelling of exposed edges of slab, fixed with chromium plated brass coupling, bottle trap, chromium plated brass centre hole mixer, PVC braided connection (two numbers), angular stop cock (stop valve) complete all as specified and as directed. Note : (i) The unit rate quoted shall be deemed to include the cost of counter WHB - 1No., Granite Slab, 32mm dia CP bottle trap - 1No., 15mm bore CP centre hole mixer - 1 No, PVC braided connections - 2 Nos, Angular stop cock - 1, brackets and other fixing accessories etc., (ii) WHB shall be fixed to granite slab with M-seal or Araldite to make leak proof joint.

Material and labour for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 (01 cement : 2 coarse sand) to math the existing floors all as specified and as directed

Material and labour for ATT along the external wall below concrete or masonry apron using chemical emulsion @2.25 litre per linear metre including drilling and plugging holes etc in apron complete all as specified and as directed.

Material and labour for Providing precast cement concrete louvers and jallies,25mm thick (measured solid) including all mouldings but excluding frame and set in cement mortar 1:4 and including provision of required reinforcement bars etc., complete all as specified and as directed.

Material and labour for taking down existing cement plaster of any description over damaged surfaces irregular facia, chajjas and in similar work and also for narrow width etc., and rendering dubbing coat 15mm thick cement plaster in CM (1:4) over a coat of cement slurry @ 3.00 Kg/Sqm making surface even (avg 50mm thick PCC 1:2:4, type B-1 using 20mm crushed stone aggregate shall be provided wherever required) followed by 5mm thick rendering in CM (1:3) finished including preparation of rendered surfaces and applying two coats of cement base paint over a coat of primer after curing of specified time and drying the surfaces as required complete all as specified and as directed.

Material and labour for preparation of old painted surfaces and applying one coat of synthetic enamel paint on steel surfaces of any description not other wise described over 10 cm width or girth etc., complete all as specified and as directed.

Material and labour for preparing newly plastered surfaces of walls and Finishing the surfaces of wall with applying acrylic smooth exterior paint of approved shade in two or more coats applied @ 1.67ltr/10Sqm over and including priming coat of exterior primer applied @ 2.2 Kg/10 Sqm complete all as specified and as directed.

M & L for complete removal of existing treatment preparing old plastered surfaces of walls and Finishing the surfaces of wall with applying acrylic smooth exterior paint of approved shade in two or more coats applied @ 1.67ltr/10Sqm over and including priming coat of exterior primer applied @ 2.2 Kg/10 Sqm complete all as specified and as directed.

Material and labour for Preparation of newly plastered surfaces of walls and applying Two or more coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50gms/litre, of approved manufacturer, of required shade and colour complete all as per manufacturer's specification over and including applying wall care putty 3mm thick complete all as specified and as directed.

Material and labour Preparation of Complete removal of existing treatment preparing old plastered surfaces of walls and applying Two or more coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete as per manufacturer's specification over and including applying wall care putty 3mm thick complete all as specified and as directed.

Material and labour for Preparation of newly plastered surfaces of ceiling and applying two coats of Oil bound distemper over and including applying 3mm thick wall care putty complete all as specified and as directed.

Material and labour Preparation of Complete removal of existing treatment, preparing old plastered surfaces of Ceiling and applying two coats of oil bound distemper over and including applying 3mm thick wall care putty complete all as specified and as directed.

Supply and Fix 100mm bore CI floor trap with grating including jointing CI pipe in run lead, cutting holes in walls and making good surface in cement concrete surface type B-1 (1:2:4) complete all as specified and as directed.

Supply and Fix 75mm bore CI floor trap with grating including jointing CI pipe in run lead, cutting holes in walls and making good surface in cement concrete surface type B-1 (1:2:4) complete all as specified and as directed.

SPECIAL ITEM OF WORK

Note for item No.105: (i) The unit rate quoted shall be deemed to include the cost of 6mm thick sheet glass and other connected accessories . (ii) For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made (iii) Net opening will be measured for payment purpose

ULSW20102POOOO of Fenesta building systems or equivalent of NCL Veka or Duroplast or Astrapia or Aparna venster or of other specified makes and fix all as per manufacturer's instructions. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in-Charge. Note for item No.106: (i) The unit rate quoted shall be deemed to include the cost of 6mm thick sheet glass and other connected accessories . (ii) For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made (iii) Net opening will be measured for payment purpose

E/M WORKS

Material and labour for point wiring complete with two runs of 1.5 Sqmm (for Phase and Neutral) PVC insulated unsheathed multistranded, copper conductor FRLSH cable of 1100V grade conforming to IS - 694 drawn through and including new non metallic rigid PVC conduit medium grade, ISI marked of suitable dia (not less than 20mm dia) with conduit accessories concealed in wall/floor and fixed on ceiling/ roof/ truss/ columns etc, including provision for modular flush box and provn of 1.5sqmm PVC insulated unsheathed copper conductor cable of green colour for earth continuity and connecting to common earth dolly etc., complete all as specified and as directed for:- Note : (a) The wiring shall be done in proper color coding using red, yellow, blue for phases, black for neutral and green for earth. (b) The cost of cutting chases in brick/stone masonry walls and making good the disturbed surfaces shall be deemed to include in the quoted rate. (c) Modular metal flush boxes, Modular cover plate with frame shall be measured and paid separately.

Supply and fix 4 feet 1 x 20 Watts LED light fitting, basic all purpose surface and wall mounted LED batten with polycarbonate housing with integrated electronic drive all as per Cat No. LUMILINEBS20WLED865 SPCWH of Havells or techno commercially equivalent of other specified makes fixed on surfaces of wall or ceiling with necessary hanging/fixing arrangements and connecting of flexible wire twin core from ceiling rose to fitting drawn through and including flexible conduit etc., including taking down old fitting complete all as specified and directed. Note: The new fittings shall bear the CA No. and Year written by Black synthetic enamel paint using stencils or by permanent marker pen and the unit quoted shall be deemed to include the cost of writing these details.

Supply and Fix Modular Switch 6 Amps, one way, flush type modular switch complete all as specified and as directed.

Supply and fix Ceiling rose, surface mount type, PVC/ Polycarbonate, with face bakelite 65 x 50mm three terminals, 240 Volt, AC Single phase complete all as specified and as directed.

Supply and Fix White cover plate with frame, 3 module complete all as specified and as directed.

Supply and Fix Modular metal flush box 3 module complete all as specified and as directed.

Supply, fix, connecting and testing MCB Single Pole and Neutral (MCB SPN), 32Amps, 240 volts of rupturing capacity 10kA, C curve type complete all as specified and as directed.

Supply, fix, connecting and testing factory made, MCB distribution board, (MCB DB), single door, SPN, 2 way, 240 Volts, having degree of protection IP 43, flush type made out of 1.2mm thick CRCA sheet metal, Phosphatised, duly powder coated and conforming to IS 8623 with copper bus bar with neutral link, earth bar and din rail etc., complete concealed and fixed flush to wall and making good the disturbed surfaces complete all as specified and as directed. Note: MCBs will be measured and paid separately.

Supply, fix, test and commissioning of Exhaust fan of size 300mm sweep, metallic body, copper winding, 1200RPM, 230V AC single phase complete set with metal blades, frames and louvers, connecting up including provn of three core flexible copper wire of size 23/0.0076 from ceiling rose to exhaust fan etc., complete all as specified and as directed.

Sri Lakshmi and Company (BID ID -3286288)