REPAIRS TO WOODEN FURNITURE UNDER GE BIRCHGUNJ MIL STN, PORT BLAIR

Amount

1.BED PLY TOP [FD-246/ 247]

Supply and fix 12 mm thick BWR plywood grade A of size 900x 1800 mm ISI Marked as confirmed to IS-303 in single piece as per drawing without any joint to the bed frame with suitable stainless steel screws with cup washers including removal of damaged ply wood all as shown on drawing and as directed by the Engineer-in-charge. Make:- Green ply/Century ply/kitply

Supply and fix in repairs to 1st class teak wood long rail as per existing size 1800mm x 85mm x 25 mm of Bed ply top including removal of damaged long rail all as Shown on drawing and as directed by the Engineer-in-charge. (Note: Each long rail will be measured as single unit)

All as per item No. 1.02 here-in-before, but short rails of size 900mm x60mm x 30mm made from existing long rail all as shown on drawing and as directed by the Engineer-in-charge. (Note: Each short rail will be measured as single unit)

Supply and fix in repairs to head board consisting of 60 x 30 x 260mm vertical size and 30 x 60 x 760mm horizontal including legs of size 60 x 60mm in section at top and 30 x 30mm at bottom length 400mm from bottom of leg complete including removal of damaged head board all as shown on drawing and as directed by the Engineer-in-charge.

All as per item No. 1.04, but foot board consisting of 22 x 75 x 200mm in section teak battens 4 Nos at equal space, joining top and bottom horizontal rails 22 x 75 x 760mm of foot board. The top and bottom horizontal rails of size 30 x 60mm shall be 1st quality of teak wood. The vertical legs above horizontal rails shall be 30 x 60mm all as shown on drawing and as directed by the Engineer-in-charge.

Supply and fix in repairs to new 1st class teak wood stiffeners of size 40 x 60mm and 900mm long complete including removal of damaged stiffeners all as shown on drawing and as directed by the Engineer-in-charge.

Supply and fix in repairs to 4mm thick OST plywood commercial of size 780 x 340mm including 12mm dia half round teak wood beading of both side of head board including removal of damaged ply all as shown on drawing and as directed by the Engineer-in-charge. Make:- Green ply/Century ply/kitply

Supply and fix in repairs to 4mm thick OST plywood commercial of size 780 x 180mm including 12mm dia half round teak wood beading of both side of foot board including removal of damaged ply all as shown on drawing and as directed by the Engineer-in-charge. Make:- Green ply/Century ply/kitply

Supply and fix in repairs to flat iron of mild steel of size 35mm x 5mm, 150 long cleat bent to right angle on each corners of Bed all as shown on drawing and as directed by the Engineer-in-charge.

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of French polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

Book Case [FD-237]

Removing the existing unserviceable shutter and providing new shutter made out of 18mm thick [600 x 480mm (2 leaves)] prelaminated particle board exterior grade including provision of teak wood beading all around including stainless steel Hinges and lock (Make:- Godrej) all as shown on drawing and as directed by the Engineer-in-charge. Make:-Ecoboard/Archid/Bhutan

Removing the existing unserviceable back of book case and providing new Back of size 1230mm x 760mm with 6mm thick plywood commercial type all as shown on drawing and as directed by the Engineer-in-charge. Make:-Greenply/Century/Kitply

BIN SOILED LINEN SMALL (750mm x 45mm x 450mm) [FD-244]

Supply & fixing in repair for the following damaged/ broken parts of Bin Soiled linen using with the material all as shown on drawing and as directed by the Engineer-in-charge.

Supply & fixing in repairs new top made of 18 mm thick prelaminated particle board exterior grade one side teak faced providing 4mm thick teak wood beading all around rest all as shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable front of bin linen small and providing new front with 6mm thick teak faced veener of approved make all as shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable back of bin linen small and providing new Back with 6mm thick commercial ply of approved make all as shown on drawing all as shown on drawing and as directed by the Engineer-in-charge.

Removing the existing bottom with leg and supply and fix new bottom with legs in repairs

Recaning of Bin soiled linen on both sides with best quality of approved plastic cane 2mm wide 0.4mm thick cane and border with 3x0.60 mm cane of white or cream ivory all as shown on drawing and as directed by Engineer-in-charge. (Note: Each side will be measured as single unit).

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coat of French polish over a coat wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

Hat Stand with mirror [FD-233]

(a) Supply and Fix in repairs new mirror 5 mm thick for Hat stand with mirror of approved make with complete frame back all as shown on drawing and as directed by the Engineer-in-charge. Make:-Saintgobin/Modiguard

b) Removing of existing unserviceable Back of Hat stand with mirror and providing new Back of 6mm plywood commercial of size 710mm with mirror fixed with headless nail, rest all as shown on drawing and as directed by the Engineer-in-Charge. Make:-Greenply/ Century ply/ Kitply

Supply and Fix in repairs brass pegs with brass screw in place of lost/damaged pegs in hat stand with mirror, rest all as shown on drawing and as directed by the Engineer-in-Charge.

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-Charge.

TABLE PEG [FD-236, FD-277]

Replacement of existing unserviceable table top for Table peg made out of prelaminated particle board of size 300 x 450m of 18mm thick with one side teak facing and balancing white on the other side and fixed with 18x12mm wooden beading (teak) on all the four sides all as shown on drawing and as directed by the Engineer-in-Charge. Make:-Ecoboard/ Bhutan Board/ Archid

Supply and fix in repairs to unserviceable damaged legs of size 380mm long, thickness 30x50mm for Table peg made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged top rail of size 20 x 40 mm for table peg made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged bottom rail of size 20x 40mm for table peg made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

SIDE BOARD [FD-241, FD-1112]

Removing the existing unserviceable top of size 1220mmx450mm side board and providing new top made out of 18mm thick prelaminated particle board exterior grade all as shown on drg and as directed by the Engr-in-Charge. Make:-Ecoboard/ Archid/Bhutan Board

Removing the existing unserviceable sides of side board and providing new side board of size length 455mm x 760mm made out of 18mm thick prelaminated particle board exterior grade all as shown on drg and as directed by the Engr-in-Charge. (Note : Each side will be measured as single unit) Make:-Ecoboard /Bhutan Board/ Archid

Removing the existing unserviceable back of Side Board and providing new Back of size 1220 mm x 760mm with 6mm thick plywood commercial type of all as shown on drg and as directed by the Engr-in-Charge. Make:-Greenply/ Century Ply/Kitply

Removing the existing unserviceable Top drawer and providing New drawer of size 385 mm x 190mm made out of 12 mm thick particle board having ply on both sides. The drawer shall run on 19 mm x 19 mm thick teak wood batten all as as shown on drg and as directed by the Engr-in-Charge. Make:-Greenply/ Century Ply/Kitply

Removing the existing unserviceable Drawers (other than Top drawers) and providing new drawer of size 180mm made out of 12mm thick particle board having ply on both sides. The drawer shall be run on 19mm x 19mm thick teak wood bearer all as shown on drg and as directed by the Engr-in-Charge. (Note : Each drawer will be measured as single unit)Make:-Greenply/Century Ply

Removing the existing unserviceable shutter and providing new shutter made out of 18mm thick prelaminated particle board exterior grade including Hinges and lock all as shown on drg and as directed by the Engr-in-Charge. (Note : Each shutter will be measured as single unit)

Removing the existing unserviceable bottom of side board and providing new bottom of size 1220 x 455 mm made out of 18mm thick plywood commercial type all as shown on drg and as directed by the Engr-in-Charge.

Removing the existing unserviceable leg frame of side board and providing teak wood 2nd class hard wood leg frame all as shown on drg and as directed by the Engr-in-Charge.

Removing the existing unserviceable broken legs of side board and providing new teak wood leg 2nd class hard wood of size 45 x 45 x 125 mm but at bottom 25 x 25 mm all as shown on drg and as directed by the Engr-in-Charge. (Note: Each leg will be measured as single unit.)

Replacement of unserviceable hinges 75mm long piano type.

Supply and fix in repairs locking device of brass 6 lever locks iron body with duplicate keys chromium plated Make:-Godrej all as shown on drg and as directed by the Engr-in-Charge.

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drg and as directed by the Engr-in-Charge.

STOOL DRESSING [FD-282]

Removing the existing unserviceable legs of stool dressing and providing with new legs of 1st class teak wood complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Removing the existing unserviceable side rails of stool dressing and providing with new side rails of 1st class teak wood complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Removing the existing unserviceable front / rear rails of stool dressing and providing with new front and back of 1st class teak wood complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Recaning of Stool dressing with best quality of approved plastic cane half round 2mm wide and 0.4mm thick plastic cane of white or cream ivory all as shown on drg and as directed by the Engr-in-Charge. Make -Premier Plastic Industries/ Garware Plastic Ltd/Maharashtra Plastic Cane Industry

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as specified on drawing or as directed by Engineer-in-charge.

TABLE DRESSING LADIES [FD-251]

Supply and fix in repairs table top of size 900mm x 380mm for Table dressing ladies with 18 mm thick pre-laminated particle Board exterior grade of approved make, all as shown on drawing and as directed by the Engineer-in-charge.

Supply and fix in repairs new 5mm thick Glass shutters of size 380mmx 550mm for Table dressing ladies all as shown on drawing and as directed by the Engineer-in-charge. (Each glass shutter shall be measured as single unit) Make:-Saintgobin /Modiguard

Removing the existing unserviceable Aluminium channel and Supply and fix in repairs Aluminium Channel of size 5.5 mm all as shown on drawing and as directed by the Engineer-in-charge.

Supply and fix in repairs new back support made out of 6 mm thick plywood for mirror of size 1020mm x 410mm for Table dressing ladies all as shown on drawing and as directed by the Engineer-in-charge.

Supply and fix in repairs new mirror 5 mm thick 366x 1220mm of size for Table dressing ladies of approved make with complete frame back all as shown on drawing and as directed by the Engineer-in-charge.

Material and labour for preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

TABLE DRESSING GENTS [FD-230]

Replacement of existing unserviceable drawer for Table dressing gents made out of prelaminated particle board exterior grade 12mm thick one side teak facing and balancing white on the other side and 12x12mm teak wood beading around all as shown on drawing and as directed by the Engineer-in-charge. Note-Each drawer measured as single unit

Supply and fix in repairs new mirror 5mm thick of size 380 x 760mm with full frame all as shown on drawing and as directed by the Engineer-in-charge. make:-Saintgobin/ Modiguard

Supply and fix in repairs new top of size 900x300mm made out of 18 mm thick pre laminated particle board exterior grade of approved make, all as shown on drawing and as directed by the Engineer-in-charge.

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

Table Bed Side [FD-276]

Removing of existing unserviceable sides of size 510mm x 230mm of Table Bed Side and providing new sides of 18mm thick exterior grade prelaminated particle Board with teak facing one side and balancing white on the other side with 18 x 6 mm teak wood beading on front sides, rest all as shown on drawing or as directed by Engineer-in-charge. (Each sides will be measured as single unit) Make:-Ecoboard/ Archid/Bhutan

Removing of existing unserviceable Top or bottom of Table Bed Side and providing new Top or bottom of size 460mm x 440mm with exterior grade 18mm thick prelaminated particle Board with teak facing one side and balancing white on the other side with 18 x 6 mm teak wood beading on front sides, rest all as shown on drg and as directed by the Engr-in-Charge. (Each Top or Bottom will be measured as single unit) Make:-Ecoboard/Archid/Bhutan

Removing of existing unserviceable Back of Table Bed Side and providing new Back of size 230mm x 450mm with 6mm plywood commercial fixed with headless nail, rest all as shown on drg and as directed by the Engr-in-Charge. Make - Kitply/ Greenply/Century Ply

Removing of existing unserviceable shelf of Table Bed Side and providing new shelf of size 207mm x160mm with exterior grade 12mm thick prelaminated particle Board with teak wood facing one side and balancing white on the other side with 12 x 6 mm teak wood beading on front sides, rest all as shown on drg and as directed by the Engr-in-Charge.Make:-Ecoboard/Archid/Bhutan

Table Bed Side MAP [FD/E6/MAP/15]

Removing of existing unserviceable sides of Table Bed Side MAP and providing new sides of exterior grade 18mm thick prelaminated particle Board with teak facing one side and balancing white on the other side with 18 x 6 mm teak wood beading on front sides, rest all as shown on drg and as directed by the Engr-in-Charge. (Each sides will be measured as single unit) Make:-Ecoboard/ Archid/ Bhutan

Removing of existing unserviceable Top or bottom of Table Bed Side and providing new Top or bottom of size 460mm x 400mm with exterior grade 18mm thick prelaminated particle Board with teak facing one side and balancing white on the other side with 18 x 6 mm teak wood beading on front sides, rest all as shown on drg and as directed by the Engr-in-Charge. (Each Top & Bottom will be measured as single unit) Make:-Ecoboard/Archid/Bhutan

Removing of existing unserviceable Back of Table Bed Side MAP and providing new Back of size 460mm x 440mm with 6mm plywood commercial fixed with headless nail, rest all as shown on drg and as directed by the Engr-in-Charge. Make - Century Ply/ Greenply/ Kitply

Removing of existing unserviceable shelf of Table Bed Side MAP and providing new shelf of size 100mm x 400mm with exterior grade 12mm thick prelaminated particle Board with teak wood facing one side and balancing white on the other side with 12 x 6 mm teak wood beading on front sides, rest all as shown on drg and as directed by the Engr-in-Charge.

Removing of existing unserviceable complete frame and supply and fix 18mm MS Square frame pipe 18 gauge colour black powder coated of size front leg size of 500mm and back leg size of 600mm rest all as shown on drg and as directed by the Engr-in-Charge. Make Tata/Jindal

Teapoy Varandah [FD-208, FD-255]

Material and labour for welding of broken joints of Teapoy verandah including preparation of surface and applying two coats of white synthetic enamel paint over a coat of red oxide primer complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Replacement of frame of top (without top) of Teapoy Verandah and Material and labour applying two coat of synthetic enamel paint white colour over a coat of red oxide primer complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Replacement of existing unserviceable table top for Teapoy verandah made out of 18mm thick pre laminated particle board teak facing on top and balancing white on the other side and all the four edges provided with teak wood beading size 18x12 mm all as shown on drawing and as directed by the Engineer-in-charge.

Material and labour for preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

Table dining 8 persons [FD-273]

Replacement of existing unserviceable table top of size 1800 mm x 900mm for Table dining 8 persons made out of exterior grade prelaminated particle board 18mm thick with one side teak facing and balancing white on the other side and fixed with 18x12mm wooden beading (teak) on all the four sides all as shown on drawing and as directed by the Engineer-in-charge. Make:-Ecoboard/ Archid/ Bhutan

Supply and fix in repairs to unserviceable damaged legs of size 60mm x 75mm x 40mm of Table dining 8 persons made out of first class hard wood (teak) complete, rest all as shown on drawing and as directed by the Engineer-in-charge.

Supply and fix in repairs to unserviceable damaged side short rails of size 900mm x 75mm x 40mm of Table dining 8 persons new side short rails made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged front/back long rails of size 1800mm x 75mm x 40mm of Table dining 8 persons new front/back long rails made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

Table dining 6 persons [FD-273]

Replacement of existing unserviceable table top of size 1500mm x 900mm for Table dining 6 persons made out of exterior grade prelaminated particle board 18mm thick with one side teak facing and other side with balancing white lamination fixed with 18x12mm wooden beading (teak) on all the four sides all as shown on drawing and as directed by the Engineer-in-charge. Make:-Ecoboard/ Archid/Bhutan

Supply and fix in repairs to unserviceable damaged legs of size 760mmx 75mmx 40mm for Table dining 6 persons and provn of new legs made out of first class hard wood (teak) legs of size 900mm x 75mmx40mm complete rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged side short rails of size 900mmx 75mmx 40mm for Table dining 6 persons and provn of new side short rails made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged front/back long rails of size 1500mm x75mm x 40mm from Table dining 6 persons and provn of new fornt/back long rails made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

14.Common for Table dining 8/6 persons

Supply and fix in repairs Triangular wooden bracket of size 50mm x 50mm 1class teak wood for all types of tables between leg & stiffeners for extra strength complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Table Dining 4' x 3' wooden [FD/MAP-II/03]

Replacement of existing unserviceable table top for Table dining 1200 x 900mm made out of Exterior grade prelaminated particle board 18mm thick with one side teak facing and white on the other side and fixed with 18x12mm wooden beading (teak) on all the four sides all as shown on drg and as directed by the Engr-in-Charge. Make - Kitply/ Bhutan Board/Archid, Echoboard

Supply and fix in repairs to unserviceable damaged legs of size 760mmx 95mmx 45mm for Table dining 4'x3' made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged side short rails of size 860mmx 95mmx45mm for Table dining 4'x3' made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged front/back long rails of size 1200mmx 95mmx 45mm for Table dining 4'x3' made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to triangular wooden bracket of 1st class teakwood 100mm x100mmx 25mm thick for all types of table between leg & stiffness for extra strength complete rest all as shown on drg and as directed by the Engr-in-Charge.

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

Teapoy :[FD-278,382]

Replacement of existing unserviceable table top of size 450x600mm for teapoy made out of exterior grade prelaminated particle board 18mm thick with one side teak facing and on the other side balancing white and fixed with 18x12mm wooden beading (teak) on all the four sides all as shown on drawing and as directed by the Engineer-in-charge.

Supply and fix in repairs to unserviceable damaged legs of size 450mmx 60mmx 30mm for teapoy made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged bottom stiffeners of size 600mmx 20mmx 10mm for teapoy made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

Table Centre :[FD-274 / 235]

Replacement of existing unserviceable table top of size 500mm x 400 mm for Table centre made out of exterior grade prelaminated particle board 18mm thick with one side teak facing and white on the other side and fixed with 18x12mm wooden beading (teak) on all the four sides all as shown on drawing and as directed by the Engineer-in-charge. Make Bhutan Board/ Archid/ Eco Board/ Kitply

Supply and fix in repairs to unserviceable damaged legs of size 380mm x60mm x 30mm from Table centre made out of first class hard wood (teak) of size 400mm complete, rest all as shown on drg and as directed by Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged bottom stiffeners of size 500mmx 50mmx 20m for table centre made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

Table Writing/Medium/Study : [FD-33,275, ]

Replacement of existing unserviceable table top of size 1145x600x760mm with exterior grade 18mm thick prelaminated particle board of approved make including edging with wooden beading all as per drg and as directed by Engineer-in-charge. Make Bhutan Board/Archid Board, Eco Board, green Ply/Kitply

Supply and fix in repairs to unserviceable damaged legs of 760mmx25mmx35mm for Table writing made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged side short rails of size 600mmx 25mm x50mm for Table writing made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged front long rails of size 1145mmx 25mm x50mm for Table writing made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged bottom stiffeners of size 1145mmx50mm x 25mm for Table writing made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged drawers of size 355mm long from Table writing made out of first class hard wood (teak) including providing 6mm thk commercial ply to bottom of drawer exterior grade 18mm thick prelaminated particle board Cabinet door & drawer along with locking arrangemnt and handles complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

TABLE WITHOUT DRAWER 900x 600 x 760mm [FD-231,284]

Removing of existing unserviceable table top for Table without drawer 900 mmx 600mm and providing new table top made out of exterior grade 18mm thick prelaminated particle board with teak wood facing one side and balancing white on the other side of with 18x4 mm teak wood beading on all round, rest all as shown on drg and as directed by the Engr-in-Charge. Make- Bhutan/Archid board/Eco Board

Supply and fix in repairs to unserviceable damaged legs of size 760mmx 60mmx40mm for Table without drawer made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged side short rails of size 600mm x60mmx40mm for Table without drawer made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged front long rails of size 900mmx 50mm x25mm for Table without drawer made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged bottom stiffeners of size 900mmx 20mm x60mm for Table without drawer made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

TABLE WITH DRAWER 900x 600 x 760mm [FD-224,283]

Removing of existing unserviceable table top of Table with drawer 900 x 600 and providing new table top made out of exterior grade 18mm thick prelaminated particle board with teak wood facing one side and balancing white on the other side with 18x4 mm teak wood beading on all round, rest all as shown on drg and as directed by the Engr-in-Charge. Make : Bhutan Board, Archid Board, Eco Board

Supply and fix in repairs to unserviceable damaged legs of size 760mmx 60mmx 40mm for Table with drawer made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged side short rails of size 600mmx 20mmx 110mm for Table with drawer made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged front long rails of size 900mm x20mmx 110mm for Table with drawer made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged bottom stiffeners of size 900mmx 25mmx 40mm (both short & long) from Table with drawer made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged drawers of size 300mm x 30mm x 20mm for Table with drawer made out of first class hard wood (teak) including providing 6mm thick commercial ply to bottom of drawer complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by Engineer-in-charge.

TABLE 900x 900mm [FD-291]

Removing of existing unserviceable table top for Table 900 x 900mm and providing new table top made out of exterior grade 18mm thick prelaminated particle board with teak wood facing one side and balancing white on the other side with 18x4 mm teak wood beading on all round, rest all as shown on drg and as directed by the Engr-in-Charge. Make - Bhutan Boad/ Archid Board/Eco Board.

Supply and fix in repairs to unserviceable damaged legs of size 760mmx 35mmx 55mm for Table 900x900mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged side short rails of size 900mm x 25mm x 75mm for Table 900mmx 900mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged front long rails of size 900mm x 25mm x 75mm for Table 900x900mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Supply and fix in repairs to unserviceable damaged bottom stiffners of size 900mm x 25mm x 75mm for Table 900x900mm made out of first class hard wood (teak) complete, rest all as shown on drg and as directed by the Engr-in-Charge.

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

Chair dining [FD-228, FD-279 or Similar]

Removing the existing unserviceable rear leg and providing with new teak wood rear leg of size 890mm x 20mm x 25mm complete all as shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new teak wood front leg of size 460mm x 20mm x 25mm complete all as shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable back rest and providing new teak wood back rest of size 430mm x 45mm x 15mm slightly curved complete all shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable front rail and providing new teak wood front rail of size 440mm x 65mm x 30mm drilling holes at 12.5 mm C/C complete all shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable rear rail providing new teak wood rear rail of size 430mmx 65mm x 30mm including drilling holes at 12.5 mm C/C complete all shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable side rails and providing new teak wood side rails of size 240mm x 65mmx 30 including drilling holes at 12.5mm C/C complete all shown on drawing and as directed by the Engineer-in-charge.

Recaning of repaired chair dining with best quality of approved plastic cane 1.80 x 0.46mm and border with 3x0.60mm cane of white or cream ivory all shown on drawing and as directed by the Engineer-in-charge. Make -Premier Plastic Industries/ Garware Plastic Ltd/Maharashtra Plastic Cane Industry

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all shown on drawing and as directed by the Engineer-in-charge.

CHAIR DINING LONG BACK WITH CUSHION [FD-357]

Removing the existing unserviceable rear leg and providing with new teak wood rear leg of size 1400mm x 25x35mm complete all shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new teak wood front leg of size 650mm x 25mm x 35mm complete all shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable seat and back of size 750mm x 450mm x 400mm and providing with new 75mm thick synthetic foam of 40mm density fixed over wooden frame covered with leathere rexin, costing not less than Rs 300.00/sqm of approved shade, texture & quality complete all shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable front rail and providing new teak wood front rail of size 450mm x 25mm x 40mm all shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable rear rail providing new teak wood rear rail of size 450mm x 25mm x 40mm all shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable side rails and providing new teak wood side rails of size 450mm x 25mm x 40mm complete all shown on drawing and as directed by the Engineer-in-charge.

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

Chair writing [FD-202, FD-250, FD-280 or similar]

Removing the existing unserviceable rear leg and providing with new teak wood rear leg of size 890mm x 55mm x 35mm complete all as shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new teak wood front leg of size 460mm x 55mm x 30mm complete all as shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable back rest and providing new teak wood back rest of size 225mm x50mm x 35mm slightly curved complete all as shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable front rail and providing new teak wood front rail of size 535mm x 30mm x 65mm drilling holes at 12.5 mm C/C complete all as shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable rear rail providing new teak wood rear rail of size 535mm x 30mm x 55mm including drilling holes at 12.5 mm C/C complete all as shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable side rails and providing new teak wood side rails of size 535mm x 30mm x 55mm including drilling holes at 12.5mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable broken arm rest and providing new teak 1st class wood arm rest of size 535mm x 15mm x 20mm complete all as shown on drawing and as directed by the Engineer-in-charge.

Recaning of repaired chair writing with best quality of approved plastic cane 1.80 x 0.46mm cane and border with 3x0.60mm cane of white or cream/ivory all as specified on drawing all as shown on drawing and as directed by the Engineer-in-charge. Make-Premier Plastic Industries/Garware Plastic Ltd/Maharashtra Plastic Cane Industry

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

CHAIR EASY [FD-203,FD-229 or similar]

Removing the existing unserviceable rear leg and providing with new first class teak wood rear leg of size 440x 35mm x 20mm complete all as shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new first class teak wood front leg of size 355mm x 35mm x 20m complete all as shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable broken arm rest and providing new first teak wood arm rest of size 510mm x 65 mm x 25mm complete all as shown on drawing and as directed by the Engineer-in-charge..

Removing the existing unserviceable front frame and providing new first class teak wood front frame of size 575mmx 510mm x 25mm x 55mm including drilling holes @ 12.5 mm C/C complete all as shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable front/back rail and providing new first class teak wood front rail of size 510mm x 55mm x 25mm complete all as shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable side rails and providing new first class teak wood side rails of size 775mm x 70mm x 40mm complete all as shown on drawing and as directed by the Engineer-in-charge.

Recaning of repaired chair easy seat and back of approved quality white or cream ivory with 1.80 x 0.46 mm cane and border with 3x0.60 mm cane complete all as shown on drawing and as directed by the Engineer-in-charge. Make -Premier Plastic Industries/Garware Plastic Ltd/Maharashtra Plastic Cane Industry

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

Comman for all Chairs

Material and labour for fixing of PVC shoes superior quality of size 25mm x25mm dia with 30mm long screws in any type of chairs all as shown & directed by the Engr-in-charge:-

CHAIR DINING OFFICER MAP ['FD/MAP-II/04]

Removing the existing unserviceable rear leg and providing with new first class teak wood rear leg of size 890mm x 20mm x 25mm complete all as shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new first class teak wood front leg of size 460mm x 20mm x 25mm complete all as shown on drawing and as directed by the Engineer-in-charge.

Removing the existing unserviceable rail/front/rear/side and providing new first class teak wood front rail/front/rear/side of size 440mm x 65mm x 30mm drilling holes at 12.5 mm C/C complete all as shown on drawing and as directed by the Engineer-in-charge.

Replacement of existing U/S cushion of Chair dining Officer and provision of new foam cushion of size 32 density 75mm thick duly covered with tapestry cloth including mulmul cloth and stitching, rest all as shown on drawing and as directed by the Engineer-in-charge. (cost of tapestry cloth shall not be less than Rs.300/m)

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

SOFA SET 4/5 PERSON WITH CUSHION [FD-281,373]

Replacement of existing U/S cushion of Sofa Set with new foam cushion of size 40 density 100mm thick duly covered with tapestry cloth including mulmul cloth and stitching, rest all as shown on drg and as directed by the Engr-in-Charge. Note :- (i) Each cushion for seat or back will be measured as single unit. (ii) The tapestry cloth shall be mat finish and rate of tapestry cloth shall not less than Rs. 450/- per Sqm and as approved by GE. Make:-Sleepweel/ Kurlon of approved make

Removing the existing unserviceable front leg from Sofa and providing new first class teak wood leg of size 70mm x 35 mm x 530mm, rest all as shown on drg and as directed by the Engr-in-Charge.

Removing the existing unserviceable rear leg from Sofa and providing new first class teak wood leg of size 70mm x 35 mm x 530mm, rest all as shown on drg and as directed by the Engr-in-Charge.

Removing existing unserviceable Armrest from Sofa and providing new first class teak wood Arm Rest of size 35mm x 70mm x 725mm, rest all as shown on drg and as directed by the Engr-in-Charge.

Removing existing unserviceable side rail from Sofa and providing new first class teak wood side rail of size 35 mm x 100mm x 725mm, rest all as shown on drg and as directed by the Engr-in-Charge.

Removing existing unserviceable bearers from Sofa and providing new first class teak wood bearers of size 40mm x 40mm x 725mm, rest all as shown on drg and as directed by the Engr-in-Charge.

Removing existing unserviceable battens from Sofa and providing new first class teak wood battens of size 50mm x 20 mm, rest all as shown on drg and as directed by the Engr-in-Charge.

Removing existing unserviceable front rail from Sofa three seater and providing new first class teak wood front rail of size 35mmx 100mm x 1590 mm, rest all as shown on drg and as directed by the Engr-in-Charge.

Removing existing unserviceable front rail from Sofa single seater and providing new first class teak wood front rail of size 35mm x 10mm x 530 mm, rest all as shown on drg and as directed by the Engr-in-Charge.

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge.

Material and labour preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abrasive cloth thoroughly for smooth and clean surface and applying two coats of french polish over a coat of wax to the depressed surface for smooth finishing complete all as shown on drawing and as directed by the Engineer-in-charge. for the following furniture articles:-

Bed Ply /Bed newar [FD-246/ 247]

Book Case [FD-237]

Bin linen small [FD-244]

Peg Table [FD-236,FD-277]

Side Board [FD-241,FD-1112]

Stool Dressing [FD-282]

Table dressing Ladies with mirror [FD-251]

Table dressing Gents with mirror [FD-230]

Table bed side [FD-276]

Teapoy verandah (Top only) [FD-208, FD-255]

Table dining 6/8 persons [FD-273]

Teapoy [FD-278,382]

Table centre [FD-274 / 235]

Table writing [FD-33,275]

Form with back wooden [FD-77M

Chair Easy [FD-229

Chair Writing [FD-280

Chair Dining [FD-279]

Chair Draughtsman [FD-204]

Desk with Dias [FD-399]

Hat stand with mirror [FD-233

Rack side 3/4 spaces [FD-106]

Sofa set 5 seater [FD-281,373]

Sofa set 4 seater [FD-281,373]

Table 3'X2' without drawer [FD-231,284]

Table office clerk wooden [DB-4120]

Table 3'X2' with drawer [FD-224,283]

Table 900mmX900mmX760mm [FD-88,291]

M/s Nikitha Enterprises

M/s Susanta Enterprises

T.THIYAGARAJAN