GE/ALP (8550) KOLKATA OF 2025-26

Amount

Demolition of brickwork or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins,arches, pillars,etc. but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Demolition of reinforced Concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers,lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc for flat rough finished surface of concrete complete all as specified and directed.

M&L for Reinforced cement concrete (nominal mix) Type B1 1:2:4 (20mm graded stone aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and directed.

All as per item No 05 here in before but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L for brick work with flyash old size bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

M&L for brick work with flyash old size bricks, straight or curved on plan to any radius in half brick thick walling built in cement mortar 1:4 complete all as specified and directed.

Taking down cement plaster on brick or stone wall surfaces including glazed tiles wherever exists including raking out joints, hacking for key and scrubbing down with water complete all as specified and as directed.

M&L for 5mm thick plastering on ceiling surfaces in CM (1:3) surface finished even and fair complete all as specified and directed.

M&L for 20mm thick (in two layer) plastering on fair face of Brick surface with CM (1:4) mixed with WPC finish surface even and smooth with out using extra cement complete all as specified and directed.

M&L for 15mm thick cement plaster with CM (1:6) on other than fare face of brick wall finsh even and smooth without using extra cement complete all as specified and directed.

Dismantling removing all unsound concrete, plastered material by chipping/chiseling gently at all effected and adjoining areas of concrete etc till sound surface is reached all various locations in building (upto 4 storied) subsequently cleaning the surfaces by hair brush and air blower and removing rubbish off the premises and disposing at the dumping site as approved by local authorities including hoisting assembling and fixing of double layer steel scaffolding to external perimeter of building complete all as specified and directed.

Removing of concrete all around reinforcement bar upto 12 mm dia and over from behind the reinforcing bars average 25mm (but not less than 15mm air gap)by manual methods (using wire brushing ,chiseling etc) and applying chloride free rust removing chemical on rusting steel reinforcement bar and removing all rust from steel reinforcement bar by emery paper and cleaning the area thoroughly by water and allow it to dry and totally rust free of reinforcement bar all as complete as per manufacturer's instruction as specified (upto 4 storied bldg). Make( Rust removing chemical ):- Reebaklens RR of FOSROC or equivalents solutions SIKA/STP.

Material , labour and preparation of existing reinforcement surface by brush and application of two component epoxy zincrich primer on existing reinforcement surface of minimum specific gravity 1.75, adhesive bond strength with steel is 1.50N/mm2 and maximum coverage area 5.00 Sqm per litre. complete all as specified and directed (upto 4 storied bldg). Make- Nitozinc primer of FOSROC or equivalents.

Material and labour for introducing new reinforcement bars upto 12 mm dia and over for structural connection in RCC beams, columns, lintel and slabs including power drilling holes of appropriate diameters in reinforced or plain cement concrete to a minimum depth of 150mm and upto 200mm including power drilling, fixing the reinforcement in position using epoxy, cleaning of loose dust by blowing air, sealing with epoxy cartridges etc complete all as specified and directed.(upto 4 storied bldg)

M&L for supply, mixing and placement of micro-concrete cement based prepacked single component chloride free, sulphate free, non-shrink, free flow. elf compacting, ready to use after mixing water in specified proportion of Sika Rep Microconcrete-4 or renderoc-RG of Fosroc in required thickness as per manufacture's instruction and all as directed. Compressive strength (ASTN C 109,cm cube) of 35 MPa at 28 days including application curing compound concrete WB manufactured by Fosroc of equivalent at various locations in Bldgs including necessary form work complete all as per manufactures specification.(upto 4 storied bldg)

M&L for providing and applying at two component structural grade polymer modified reinforcement mortar Fosroc Renderoc S2 or equivalent product of SIKA upto a thickness of 30 mm over a coat of epoxy resin bonding agent Nitobond EP. The cured mortar shall achieve a minimum compressive strength of 12N/mm2 in a day & 45 N/mm2 in 28 days with Flexural strength 8N/mm2 in 28 days Chloride diffusion coefficient shall be Nil after 24 hours when tested by Accelerated electrochemical chloride ion diffusion test method and the depth of carbonation shall be Nil after 24 hours when tested by Accelerated carbonation test. in addition to this percentage of water absorption should be 0.45 after 24 hours in immersion test at various locations in Bldgs complete all as per manufacture's specification.(upto 4 storied bldg)

Material , labour for applying of high efficiency polymeric resin base film forming curing agent/compound over concrete surface and maximum coverage area 5.00 Sqm per litre as per manufacturers instruction complete all as specified and directed.(upto 4 storied bldg) Make:- Concure LP90 of FOSROC or equivalents solutions SIKA/STP/ Maruti / Choksey chemicals.

Material & Labour for applying Anti carbonation coating as per manufacturer's specification of approved brand, manually using brushes on the hardened concrete/plastered surfaces after cleaning the surface and removing all loose particles, deposits etc complete including one coat of primer and two coats coatings complete all as specified and as directed.

Material & Labour for Carbon Fibre Wrapping - Nitowrap CWS – 450 GSM Providing and carrying out Fosroc make carbon fibre wrapping Nitowrap CWS (450 GSM) - High Performance high strength, carbon fibre system for structural strengthening to R.C. members. Surface Preparation : Proper surface preparation to be carried out including cleaning, removal of loose material, dust etc, executing required repairing like epoxy injection grouting, polymer modified mortar, epoxy touching Putty , rounding off edges of structural members to 25mm etc . Application : Prepared substrate shall be primed with Nitowrap 30 epoxy primer supplied in pack size 4 Lit (Base-4.1 kg and Hardener -0.46 kg) at a coverage of 8-10 m2/litre/coat, allow the primer to cure for 24 hours followed by application of first coat of saturant Nitowrap 410 supplied in pack size 5kg ( Base - 3kg and hardener - 2kg) (having Tensile strength >30 MPa; Elongation > 2.1% ; Fibre strength > 4900 MPa ; Fibre E-Modulus >230 GPa & Flexural Modulus > 1700 MPa when tested as per ASTM D638 Type I and ASTM D 790 & Glass Transition Temperature > 50 °C as per ASTM E 1356) to be carried out at a coverage of 3.5 to 4 m2/lit/Coat at around 250 microns WFT, cutting of Nitowrap CWS (available in standard roll width of 500 mm and roll length of 50 mtr & 100 mtr) in required size and wrap over wet saturant keeping minimum 150 mm overlap, rolling the same using hard roller to impragnent saturant and again applying second coat of saturant using suitable bush or roller etc, completing as per specification and as directed by Engg.-in-charge. Nitowrap CW fabric used shall exhibit the following properties - fiber density of 1.8 g/cc, dry fibre thickness 0.40mm and shall have tensile strength > 4900 MPa ; tensile modulus > 230 GPa and ultimate elongation of 2.1%.The adhesion of the entire system(FRP Sheet, Saturant and primer combined) with concrete shall be > 3.5 MPa with concrete failure as per ASTM D 4541 complete as per specification and as directed.

M&L for providing grouting in RCC walls and slabs by drilling holes @300 mm c/c upto half of the wall depth in zigzag manner using a drill machine and fixing a nozzle of 20mm dia, for injecting of epoxy grout till the refusal of injected grout material (grouting operation pressure shall be in between 2 to 4Kg per sq cm) followed by cutting the exposed nozzle so as to make the wall/ slab free from the grouting pipe and to seal the gap with polymer modified mortar complete all as specified and directed.(upto 4 storied bldg) Make- Fosroc conbextra Ep10(M) or equivalent make as approved by GE.

Taking down chowkhats or frame with shutter (without taking off shutters from the frame) exc 1.5 sqm n.exe 4 sqm each complete all as specified and directed.

Taking down rusted steel windows/ventilators of any description and size including shutters complete all as specified and as directed

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws complete all as specified and directed.

S&F Anodised powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators or aluminium frame for partition works etc with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868) of approved design/pattern, with approved standerd section and fix to the existing window frame with C.P brass/stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction complete all as specified and directed. (only weight of grill to be measured for payment)

S&F 12 mm thick prelaminated particle boards (ISI marked), interior grade prelaminated both side with decorative choice lamination, fixed with necessary clips and other like to aluminium frame work, as in doors, windows, partition etc complete all as specified and as directed.

S&F Glass film reflective type sticked to glass panes as per instructions of manufacturers intructions complete all as specified and directed.

S&F 10mm thick toughened glass as in hinged doors,partitions, automatic doors and similar work including cutting to shape,drilling holes required complete all as specified and directed.

S&F 4.8 mm thick glass ordinary quality, frosted on one side fixed to aluminium frame work exc 0.5 Sq. m in each pane complete all as specified & as directed.

S&F 4.8 mm thick glass ordinary quality, frosted on one side fixed to aluminium frame work n. exc 0.5 Sq. m in each pane complete all as specified & as directed.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified & as directed.

S&F Stainless steel handles 150mm long, bright polished complete all as specified and directed.

S&F 300mm long sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bots and sliding bolts of extruded or cast aluminium alloy complete all as specified and directed.

S&F Stainless steel barrel tower bolts of extruded section with 150 mm long bolt, complete all as specified and directed.

S&F Bearing hinges 100mm, cast brass, with Stainless steel hinge pin, bright polished and fixed, typeB-11 complete all as specified and directed.

S&F for Stainless steel wire cloth having 0.36 mm nominal dia of wire and average width of appreature 1.40 mm and fixed with stainless wire staples complete all as specified and directed.

S&F in repair aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed.

S&F floor door stopper overall length of cover plate 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), clamps; hold fasts; wall ties; and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets. (up to 4 store) complete all as specified and directed.

M & L for GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc. 1.2m length) of 0.55 mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre and incl Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat (40 x 3) mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed. (up to 4 storey)

Providing and fixing Gypsum Board 12mm thick in ceiling flat or slopping fixed in jointless finish with jointing compound and jointing tape fixed with screw as per manufacturers instructions with provn of light/electric fixtures complete all as directed complete all as specified and directed (upto 4 storey)

M&L for preparing new gypsum board ceiling, pillasters, cornices etc and applying one coat of 3 mm thick wall care putty with two coat acrylic distemper complete all as specified and as directed (upto 4 storey).

Dismantling floor , earth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for double charged Vitrified ceramic tiles 9-10 mm thick (Sqr/ rectangular) Polished, area of each tiles exc. 0.36 sqm but n.exc 0.42 sqm, in floors etc. set and jointed with adesive and pointed in epoxy grout with spacers over a bedding layer of scread bed 15 mm thick in CM (1:4) complete all as specified and directed.

M&L for glazed ceramic (coloured) tiles of size (300x600 6-7)mm thick as in vertical surface/dado set and jointed in adesive and pointed in white or coloured cement to match complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors,aprons etc laid, bedded & pointed in any mortar complete all as specified and directed.

M & L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, indow-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 20 mm thick in CM (1:6) for laying floor finishes complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15 mm thick in CM (1:6) for laying floor finishes complete all as specified and directed.

M&L for bedding layer of mortar 10 mm thick in CM (1:3) for laying wall/dado finishes complete all as specified and directed.

Demolition of cement concrete above ground floor n.exe 15cm thickness(below or above ground level) complete all as specified and directed.

M&L for 25mm thick cement concrete type B-0, (1:2:4) using 12.5mm graded stone aggregate complete all as specified and directed.

M &L for 150mm thick PCC (1:2:4) Type B 2 (40 mm graded stone aggregate) as in sub base complete all as specified and directed.

Dismantling of 100mm cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

S&F 20 mm bore (Outer dia) CPVC pipes of SDR 11and plain CPVC SDR 11 fitting fixed on wall or floor (concealed ), ceiling or laying in floors complete all as specified and directed.

S&F in 40 mm bore (Outer dia) CPVC pipes of SDR 13.5 and plain CPVC SDR 11 fitting fixed on wall or floor, ceiling or laying in floors complete all as specified and directed.

S&F 50 mm bore (Outer dia) UPVC pipes of SCH-40 and plain UPVC SDR 11 fitting fixed on wall or floor, ceiling or laying in floors complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 20 mm bore CPVC Male Brass Threaded Adaptor (MTA/ MBTA) complete all as specified and directed.

S&F 20mm bore CPVC Female Brass Threaded Adaptor (FTA/ FBTA) complete all as specified and directed.

S&F 50 mm bore CPVC Male Brass Threaded Adaptor (MTA/ MBTA) complete all as specified and directed.

S&F 50 mm bore CPVC Female Brass Threaded Adaptor (FTA/ FBTA) complete all as specified and directed.

S&F PVC (SWR) bends 110mm dia complete all as specified and directed.

S&F PVC (SWR) junction single, (Single T) equal or unequal 110 mm dia complete all as specified and directed.

S&F PVC (SWR) junction double, (Double T) equal or unequal 110 mm dia complete all as specified and directed.

S&F in repairs vitreous china wash hand basin, white, flat back, size (550mm x 400mm), exc chain and plug and porcelain stopper but including cutting for and pinning in ends of and including brackets, waste pipe & CP brass waste coupling of 32mm dia complete all as specified and directed.

S&F in repairs Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed.

S&F in repairs 15mm bore CP angular valve fancy type,with crutch handle, screwed for iron pipe or for brass ferrule and fixed of following size complete all as specified and directed.

S&F in repairs 15 mm bore CP pillar taps, with capstan heads, chromium plated, Fancy type screwed down for pipe, high pressure ,complete all as specified and directed.

S & F in repairs 25 mm Dia brass gun metal gate valve , with crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair 600 mm PVC connection pipe 15 mm size with PTMT nut of following length complete all as specified and directed .

S & F in repair 110/125 mm floor trap fixed in floor with grating incl jointing with solvent (1:2:4) cement concrete,complete all as specified and directed.

S&F in replacement Curtain rails with Decorative type drappery Rod along with all fittings of 25 mm dia complete all as specfied and directed.

S&F in repair brass CP Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specfied and directed.

Supply and fixing of rotational moulded polythene water storage tank 1000 litre capacity ISI marked (cylindrical, vertical, double layered with closed top) hoisted and fixed in position including PVC float valve 20mm bore weight not less than 210gms Complete including dismantling of old unserviceable water tank, removing from site complete all as specified and directed.

Taking out/Stripping of old Roof treatment membranes/Tar felt incl layer of cement mortar of any type carefully from roof surfaces (without damaging roof ) and incl preparation of old roof surfaces by picking, sweeping, cleaning and washing down with water to remove dust & receive new treatment complete all as specified and directed.

Material and labour for carry out waterproofing treatment to sound, moisture free concrete surface using nitroproof 600PF- liquid applied single component pitch free polyurethane coating capable of bridging substrate cracks upto 2 mm. System includes proper surface preparation to remove loose dust, dirt, loose mortar, curing compound etc. and application of Nitroproof WB primer, water dispersible epoxy primer followed by two coats of Nitroproof 600 PF coverage @ 2.0 kg/m2 to achieve 1.5 mm WFT in two coats followed by laying of seperation layer of 120 gsm non-woven geotextile layer before carry out protection screed etc. complete including all tools and tackles as per manufacturere's specification. Nitocote 600PF cured material shall be having crack bridging of 2mm, Elongation (ASTMD 412) - >600%, Tensile Strength (ASTM D412) - 2.5 N/mm2, Recovery from Elongation (ASTM D412) - 95%, 85% Solid Content, Tear Resistance (ASTM D624) - 15 Kn/m, Shore A (BS EN 12390)- Nil, Service Temperature- -40oC to 70oC, Flash Point > 70oC, Viscoaity-60p, Specific Gravity-1.5. The item rate shall be including of all kinds of labour, tools & tackle, machineries, lead & lift, mathadi charges, curing, wastages, consumable, cleaning, shifting of debris outside the site premises, surface seperation etc. complete as per design, drawing & instructions of EIC. Cost of 120 gsm non-woven geotextile and 75 mm Screed concrete Shall be paid seperately.

Supply & Laying Geotextiles of 120 Gsm over the waterproofing coating to avoid damage during screed casting complete all as specified and directed.

Supply & laying of maximum 75 mm thick (at RW outlet) protective screed over the waterproof coating at proportion of (1:2:4) admixed with suitable integral waterproofing compound conforming IS 2645:2003 @ 200ml per bag of cement and reinforced with PP fibres with proper slope towards RW pipes. Green stage saw cutting on the screed will be done in panels (3m X 3m) with a groove size of (10 mm X 15 mm) complete as specified and as directed

S & F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

Complete removal of existing treatment by using electric sander machine or steel wire brushing to remove all dust and loose scale etc of wall surfaces & prepare to receive wall care putty complete all as specified & directed.

M&L for 2 mm thick wall care putty on wall including rubbing with sand paper to achieve a smooth surface & sharp straight edges etc. complete all as specified & as directed.

M&L for preparation of newly plastered wall surface two coats of oil emulsion distemper over a coat of primer on complete all as specified and directed.

M&L for preparation old decorated walls & applying two coats of acrylic oil bound distemper over a coat of 1mm thick wall care putty complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over 1mm thick wall care putty and icluding priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed.

Material & Labour for Complete removal of existing treatment and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces complete all as specified and as directed.

M&L for preparation of new decorated Ceiling surface & applying two coats of acrylic oil emulsion distemper complete all as specified and directed.

M&L for preparation of old decorated Ceiling & applying one coats of acrylic oil emulsion distemper complete all as specified and directed.

M&L for preparing of new steel surfaces & applying two coats of synthetic enamelled paint over a coat of red oxide primer complete all as specified and as directed.

M&L for preparing of old steel surfaces & one Coats of Synthetic Enamel Paint over one coat of primer to steel and iron surfaces of any description, not otherwise described including preparation of old surface complete all as specified and directed.

M&L 60 mm thick machine pressed precast interlocking paver block of M-35 Grade any shape and size with grey cement and pigment confirming to IS 15658-2006 complete all as spd and directed.

M&L Chequered cement concrete tiles (20cm x 20cm x 25mm) thick,set, jointed and pointed in neat cement slurry in floors with grey cement in equal proportion & no pigment over 15mm thick screed bed with CM (1:6) complete all as specified and directed.

M & L for 100 mm thick cement concrete type C2,(1:3:6) (using 40 mm graded stone aggregate) as in floors complete all as specified and directed.

Hard core of gauge in exc. 63mm broken stone boulders deposited and spred and leveled in layers n.exc. 15cm thick complete all as specified and directed.

M&L sand filling under floor or in floor or paving, laid in including watering and consolidation true surface for laying paver block complete all as specified and directed.

Supply only Intregal water proofing compound complete all as specified and directed.

M & L for Cement concrete in saucer drains Type B1 (1:2:4) (40 mm graded stone aggregate) slope maintained as per site requirement complete in all respect as specified.

M&L for 75mm thick PCC (1:3:6), type C2, using 40mm graded stone aggte as in plinth protection / paving, surfae finished even & smooth without using extra cement as complete as specified and directed.

M&L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete as specified and directed.

Material and labour for Providing cement concrete type B-1 (1:2:4) (using 12.5 mm graded stone aggregate) as in benching concrete,coping etc complete all as specified and directed.

S&F Brass chromium plated brackets complete all as specified and directed.

M&L for precast cement concrete (1:2:4) type B-0 (using 12.5mm graded stone aggregate) kerbs stone rounded or chamfered on edges as in edge of path, hard standing built in cement mortar 1:6 complete all as specified and as directed.

Taking down aluminium door(any size) and refixing in same position ,change of pivot, beading, gasket, setting of door and change of damaged style /rail any length in aluminium section thickness not less 1.50 mm match with existing anodised /power coated complete and refixing in same position complete all as specified and directed.

Taking down aluminium windoow (any size) and refixing in same position ,change of pivot, beading, gasket, setting of door and change of damaged style /rail any length in aluminium section thickness not less 1.50 mm match with existing anodised /power coated complete and refixing in same position and complete all as specified and directed.

S & F factory made 2nd H/W plain solid straight chowkhats,wrought framed rebated on the solid,rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

M&L for Factory made 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with both face covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

S&F floor power door stopper overall length of cover plate 150mm of zink alloy body and fixed in floor complete all as specified & as directed. Make : Prayag Cat Part No DSZ-PW6-SS or equivelant make as approved by GE

S&F aluminium 4 levers Mortice lock, vertical type, size 100 mm complete all as specified and directed.

M&L for suspended false ceiling (Decorative Type) system using metalic (E grid) exposed suspende system, grid section size (600mm x 600mm) comprising of GI powder coated main runner of dimension (32 mm x 24mm x 0.80mm) thick ( thickness comprising of GI/0.4+ PPPCGS/0.3mm & weight of Runner) Cross Tee of dimensions (26mm X 24mm x 0.8 mm) thick, wall angle (22.00mm x22.00mm x 0.35 mm) thick ( thickness comprising of GI/0.35 + PPPCGS/0.3 mm) with and including 4 mm thick HPSC ( High pressure steam cured) pre- primed, self embossed textured designer board, water resistant termite resistant, fire resistant for insulation and accustic purpose to be placed in the grid system duly suspended with 2 mm dia G I bars hangers fixed with steel dash through fasteners with Provn of light fixture complete all as specified and directed.

M&L for full body homogeneous vetrified tiles tiles 9-10 mm thick (Sqr/ rectangular) Polished, area of each tiles exc. 0.18 sqm but n.exc 0.36 sqm, in floors etc. set and jointed with adesive and pointed in epoxy grout with spacers complete all as specified and directed.

M&L for full body homogeneous vetrified tiles tiles 9-10 mm thick (Sqr/ rectangular) Polished, area of each tiles exc. 0.42 sqm but n.exc 1.00 sqm, in floors etc. set and jointed with adesive and pointed in epoxy grout with spacers complete all as specified and directed.

M&L for glazed ceramic (coloured) tiles of size 600x1200 6-7 mm thick as in vertical surface/dado set and jointed with adesive and pointed in white or coloured cement to match complete all as specified and directed.

M&L for double charged Vitrified ceramic tiles 9-10 mm thick (Sqr/ rectangular) Polished, area of each tiles exc. 0.42 sqm but n.exc 1.0 sqm, in floors etc. set and jointed with adesive and pointed in epoxy grout with spacers complete all as specified and directed.

Bore packing of all the Spouts to be done with grouting admixture mixes with Cement Concrete / Mortar @225 ml per bag of Cement complete all as specified and directed.

S&F in repairs one piece EWC, Snow white, with slim soft close seat cover and S-Trap 220 mm , including connection to drain ( or outgoing pipe) complete all as specified and directed. Make:-Cera or Equivalent make as approved by GE

S&F in repairs vitreous china Table Top wash basin, white, including cutting for and pinning in ends of and including brackets, waste pipe & CP brass waste coupling of 32mm dia complete all as specified and directed. Make:-Cera or Equivalent make as approved by GE

S & F in repairs 15 mm Dia CP Bib taps with wall flange and aerator ,fancy type with crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make:-Cera Cat-2024, Cat No-F1018151 or Equivalent make as approved by GE

S & F in repairs 15 mm Dia CP Bib taps (Two-in-one), with wall flange and aerator ,fancy type with crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make:-Cera Cat-2024, Cat No-F1018163 or Equivalent make as approved by GE

S & F in repairs 15 mm Dia CP stop cock(concealed type) ,fancy type with crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make:-Cera Cat-2024, Cat No-F1018351& F4050102 or Equivalent make as approved by GE

S&F in repairs 15 mm bore CP single lever basin mixer with 305 mm extended body and 600mm braided connection pipe, screwed down for pipe, high pressure ,complete all as specified and directed. Make:-Cera or Equivalent make as approved by GE

S&F in repairs 15 mm bore brass CP Wall mixer, Fancy type with 210 mm long bend pipe for overhead shower, for mixing Hot and Cold water screwed down for iron pipe, complete all as specified and directed. Make:-Cera Cat-2024, Cat No-F1018402 or Equivalent make as approved by GE

S&F in repair CP Health faucet ABS body with 1 meter SS braided connection pipe complete all as specified and directed. Make:-Cera Cat-2024, Cat No-F8030109AB or Equivalent make as approved by GE

S&F (1200 mm x 600 x 5 mm) mirror with decorative type double coat for protection and longevity and on silver plating the back for better reflection including necessary fittings comlete all as specified and directed. Make:-Cera or Equivalent make as approved by GE

S&F in repair brass CP Shower roses (150x150) mm, including fixing to steel pipes or union comlete all as specified and directed. Make:-Cera or Equivalent make as approved by GE

S&F CP Soap dish, fixed to plugs with chromium plated brass screws comlete all as specified and directed. Make:-Cera or Equivalent make as approved by GE

S&F in repair brass CP Tubular towel rack, 600 mm long between flanges complete all as specfied and directed. Make:-Cera or Equivalent make as approved by GE

S&F brass CP toilet Paper Holder with flap guard complete all as specfied and directed. Make:-Cera or Equivalent make as approved by GE

S&F Corner glass shelf with 2 racks complete all as specfied and directed. Make:-Cera or Equivalent make as approved by GE

S&F Decorative type wall paper (Ornamental type) used to cover and decrate wall surface complete all as specified and directed.

Solid PVC Wall Lining wood grain printed PVC sheet consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and as directed.

5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and as directed.

M&L for one coat of plastic emulsion paint on old decorated surface of internal walls incl preparation complete all as specified and directed.

M&L for Two coats of synthetic enamel paint on old wooden surface exc 10cm width or girth including preparation complete all as specified and as directed.

Taking down carefully copper/aluminium point wiring complete (light,fan, plug point & power complete alongwith fittings (switches, ceiling roses, tube light fittings, bulk head fitting regulator, sockets main switches, DB removing materials to store & making good of disturb surfaces of wall/floors etccomplete all as specified and as directed.

M&L for point wiring complete as specified with 1100 V grade with 1.5 Sq mm single core PVC insulated unsheathed FRLSH cable, copper conductor multistranded passing through including concealed PVC conduit not essthan 20 mm dia with concealed modular box suitable for logic modular switches , sockets , etc with logic modular white plates, sorroundings of suitable size as required at site with PVC insulated FRLSH unsheathed stranded copper conductor of size 1.5 sq mm as earth wire connected to common earth dully as specified complete all as specified and directed for the following:- Note: - (i) Rate quoted shall include for cost of making MS box and concealed in wall including cutting and sinking of boxes and making good to the walls (No extra payment will be made for the same) (ii) Provision of cover plate and blank plates as per site requirement (No extra payment will be made for the same)

One light point / one fan point controlled by one, one way swtich complete all as specified and as directed.

All as per item No 139 here in before but for 5 Amp switch socket on the same board complete all as specified and as directed.

All as per item No 139 here in before but for 5 Amp switch socket on independent board complete all as specified and as directed.

All as per item No 139 here in before but size of cable 2.5 sq mm with earth wire of 2.5 sq mm complete all as specified and as directed.

All as per ser item No. 139 here in before but one bell/buzzer point controlled by one push button on the same board with other switches or independent complete all as specified and as directed.

Supply and fixing Switch modular type, single pole, one way, 5/6 Amp, one module, completes all as specified and directed.

Supply and fixing Switch modular type, single pole, one way, and 15/16 Amps, one module complete all as specified and as directed.

Supply and fixing socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, two module, modular type completes all as specified and directed.

Supply and fixing socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin 5/6 Amp, modular type completes all as specified and directed.

Supply and fixing Switch modular type, single pole, Bell push, 5/6 Amp, one module, completes all as specified and directed.

Supply and fixing in replacement of bell ding dong type AC, 230 volts, single phase complete all as specified and directed.

Taking down ceiling fans , any type and depositing AGE E/M STORE complete all as specified and directed.

Fixing only ceiling fans complete with blades, complete all as specified and as directed.

Supply and fixing Fan Step Regulator modular type, two module, completes all as specified and directed.

Supply and fixing in replacment of ceiling rose of size (65 x 50) mm surface bakelite 240 Volts three terminal as specified and directed.

Supply & fix LED tube 20 W Tube light fitting inverter LED Batten with square profile and polycarbonate channel alaithium Ion Bettery connecting up with three core flexible copper conductor cable of suitable size from ceiling rose up to 1.5m length complete all as specified and as directed.

Supply and fix MCB DB TPN 4 way IP 43 protection ,double door , concealed on wall complete all as specified and as directed.

Supply and fix MCB DB SPN double door 08 way , IP 43 protection concealed on wall complete all as specified and as directed.

Supply and fix MCB DB SPN double door 04 way , IP 43 protection concealed on wall complete all as specified and as directed.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of SPN and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and as directed.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed .

Supply and fix MCB 63 Amp 4 Pole ,10 KA complete all as specified and as directed

Supply and fix power unit 32 Amps including socket 25 AMp ,06 module metal box for mounting of power unit complete as specified and directed. Make : Legrand Cat Part No.6755 58 /Havells/ ABB/ L&T. for Power unit , 6772 32 for socket 25 Amp and 6890 10 for metal box 6 Module

M & L for submain wiring with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLSH type, cables 6 Sqmm drawn through in and including rigid PVC heavy duty concealed conduits including 6 Sqmm 1100 Volts grade, FRLSH type, PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed. Note :- (i) Three runs of cables drawn in conduit will be measured as one length of sub main. (ii) PVC conduit and its accessories is deem to be included in this item rates. (iii) Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc.

M & L for submain wiring with two single core PVC insulated unsheathed, multistranded flexible copper conductor 1100Volts grade, FRLSH type, cables 4 Sqmm drawn through in and including rigid PVC heavy duty concealed conduits including 6 Sqmm 1100 Volts grade, FRLSH type, PVC insulated unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed. Note :- (i) Three runs of cables drawn in conduit will be measured as one length of sub main. (ii) PVC conduit and its accessories is deem to be included in this item rates. (iii) Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc.

Material & Labour in replacement of Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6.3 mm thickness burried directly in ground (earth pit not less than 2.25mtr deep below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to and incl galvanised earth lead wire of 4.00 mm dia by means of nuts & bolts, check nuts and washers of galvanised incl PCC pit of (1:2:4) type B-1, cover reinforced with XPM weight not less than 4 Kg/Sqm and 6mm dia bar handle, earth pit angle iron frame of size (25mm x 25mm), excavation and earth work in any type of soil, charcoal dust, salt, light grade GI watering pipe 20mm dia with funnel and wire -mesh and medium grade GI protection pipe of 15mm bore from top edge of earth plate upto main distribution board complete all to as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected main switch board all as specified and testing on completion.

S B ENTERPRISE (BID ID -3453190)

M/s Santosh Industrial Corporation (BID ID -3453921)

M/S SK PAUL (BID ID -3454235)

EAST COAST STANDARD PRODUCTS (BID ID -3452891)

Megatrend Systems (BID ID -3453861)