SPECIAL REPAIRS AND ADDN/ALTN TO BLDG No 250 OF 24 FD WKSP, SPL REPAIR TO BLDG No T-20 AND T-21 OF 21 CORPS OMC AND SPL REPAIR TO GATE AT KSP OF SUPPLY DEP ASC AT NASIRABAD.

Amount

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified.

M&L for rendering 10mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified.

M&L for rendering 15mm thick in cement mortar 1:4 on stone masonry surfaces or surfaces other than fair face of brick work of walls (external surfaces), finished even & smooth without using extra cement complete all as specified.

M&L for rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

M&L for 20mm thick rough cast plaster mix with crushed stone (6-10mm), sand and cement in the ratio 1:1:1 over and including 15mm thick rendering in cement mortar 1:4 mixed with water proofing compound, on external wall surfaces, complete all as specified & directed. Note: WPC shall be measured & paid separately.

Supply only water proofing compound, ISI marked.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer all as specified & as directed.

M&L for preparation of old decorated surfaces of walls by washing, rubbing down and stopping of distempered surfaces and applying two coat of oil emulsion distemper (OBD) of approved shade/tint all as specified & as directed.

M&L for preparation of newly plastered surfaces of ceilings & applying three coats of white wash complete all as specified.

M&L for preparation of old white washede surfaces of ceilings & applying two coats of white wash complete all as specified.

M&L for preparation of newly plastered surfaces of walls & applying three coats of white wash complete all as specified.

M&L for preparation of old white washed surfaces of walls & applying two coats of white wash complete all as specified.

M&L for preparation of new rough cast plastered surfaces of walls and applying two coat of weather proof acrylic emulsion paint (exterior grade) of approved shade/tint over a coat of emulsion primer, complete, all as specified & as directed. Make of paint: Asian/Apex/Berger.

M&L for complete removal of existing treatment and applying two coats of weather proof acrylic emulsion paint of approved shade/tint over a coat of emulsion primer over & including 1mm thick finished coat of white wall care putty on walls all as specified & as directed. Make of Putty: Birla/JK/Asian Make of paint: Asian/Apex/Berger.

Taking down chowkat or frame with shutters area not exc 1.5 Sqm each (without taking off the shutters from the frame) including cutting holes for hold fasts & making good disturbed surfaces of wall in CM 1:3, complete all as specified.

Taking down chowkat or frame with shutters area exc 1.5 Sqm but not exc 4 Sqm each (without taking off the shutters from the frame) including cutting holes for hold fasts & making good disturbed surfaces of wall in CM 1:3, complete all as specified.

S&F steel window with side hung shutters including projecting type hinges with steel handles and peg stay with glazing bars dovetailed or welded complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete, all as specified & directed.or fixed with bead.

S&F 3mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each panel, complete all as specified.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified.

S&F 5.5 mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified.

S&F mild steel framed work as in doors / gates / steel frames / chowkats etc. of angle or other section with gusset plates, rails, braces, etc., complete conforming to Grade E-165 (Fe 290), drilled for fixing of steel sheeting or other covering including necessary welding etc and fixing in position complete.

M&L for welded steel wire fabric fixed to wood or steel members, weight not exceeding 4 Kg/sqm, complete all as specified & directed.

M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint all as specified & as directed.

M&L for preparation of new untreated steel and iron surfaces of any description, not exc. 10 cm in width or girth when unconnected with other painting or when painted in a different tint and applying two coats of synthetic enamel paint over a coat of zinc chrome primer complete all as specified.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified.

M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint all as specified & as directed.

Dismantling AC sheet (Corrugated, Semi corrugated etc) as in roofs etc including ridges complete all as specified.

Supply and fixing 6 mm thick non asbestos cement, corrugated or semi corrugated sheets in roofs, walls etc and fixed with ‘L’ type or ‘J’ type or cranked hooks bolts complete all as specified.

All as per serial item No 31 here-in-before but except sheets.

M&L for non asbestos cement one piece plain angular ridge/valley 6mm thick fixed with ‘L’ type or J type or cranked hook bolt, all as specified & directed.

S&F 2 mm thick fibre glass reinforced translucent corrugated/plain sheeting with two corrugation 15 cm side lap, fixed with L-type or J-type or cranked hook bolts/self taping screw and washer in roof, wall etc complete all as specified and directed.

S&F Butt hinges, 125 mm size medium weight, cold rolled mild steel, complete, all as specified and directed.

M&L for dismantling of loose/disintegrated portion of RCC chajjas, band, shelves, beams, balconies and similar work at any position & any height, doubbing out with PCC 1:1.5:3, 15 mm to 50mm thick using 6 to 12 mm graded stone aggregate to make up and finished to required shape including necessary form work wherever required including 10mm thick plastering in CM 1:4, finished even and smooth on concrete surfaces and applying anti corrosive paint on exposed surfaces , complete, all as specified & directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint complete all as specified.

M&L for preparation of old decorated plastered surfaces of walls and applying one coat of cement base paint of approved shade/tint complete all as specified.

M&L for complete removal of existing treatment and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 1mm thick finished coat of white wall care putty (make-Birla/JK/Asian) on walls all as specified & as directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer over & including 1mm thick finished coat of white wall care putty (Make-Birla/JK/Asian) on walls all as specified & as directed.

Demolition of plain cement concrete in ground floor and pavings not exc 15 cm thick (below or above ground level) including floor tiles of any description complete all as specified.

M&L for machine cut Kota stone slab flooring of size not less than 550X550mmX18-20mm thick over and including 15mm thick screed bed in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over and including cement screed plaster 10mm thick in CM (1:4) & jointed with grey cement slurry mixed with pigment to match the smooth of the slab including rubbing & polishing complete all as spd & directed.

M&L for 25 mm thick PCC (1:2:4) type B-1 using 20 mm graded stone aggregate as in sub base of floors, complete all as specified & directed.

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

Dismantling of ceiling board/lathing any thickness including frame work complete all as specified and directed.

Providing & fixing false ceiling with Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all heights as per direction of Engineer-in-charge. Make: Everest or equivalent specified in Particular specifications

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ 'L' or 'J' type hook complete all as specified & directed.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/ 'L' or 'J' type hook complete all as specified & directed.

S & F Steel window/ventilator factory made, out of MS hollow section 79mm x 39mmx1.6mm thick frame with double shutter (glazed & wiregauged shutters) made out of Z section using flush butt welding and tennon riveting all as per IS 1038/83, dobby hinges shall be provided to both shutters, Locking arrangements as per sample approval by GE, provided with knob, 10mm MS square bars in grill, Z section handle 100mm size and 150mm long hook & eye welded to frame and shutter, four Nos lugs welded to frame inculding necessary flat iron beading for securing wire gauge etc including holes, cutting holes for hold fast and making good in PCC 1:2:4 type B-1 including two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and directed. Note : Wire mesh and sheet glass shall be measured & paid separately under respective items.

S & F aluminium handle fabricated type, anodised 150mm size conforming to IS complete all as specified and directed.

Supply and fixing brass mortice lock, vertical type, size 100 mm, 4 Levers with escutcheon plates & two keys fixed in aluminium frame complete all as specified.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified

S&F 125 mm size aluminium butt hinges (ISI marked) complete all as specified

S&F in repairs fancy type 20mm dia stainless steel curtain rods fixed to bracket complete all as spd & directed.

S&F decorative type knobs with bracket of stainless steel fixing at end of curtain rod complete al as spd & directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed with wire staples complete all as spd & directed.

Demolition of stone/brick masonry built in cement or cement lime mortar, complete, all as specified and directed.

M&L for brick work with flyash bricks straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

All as per description of serial item No. 59 above but except brick complete all as specified and directed.

M & L for PCC 1:2:4 type B-2, using 40 mm graded stone agg as in surface channel & drain etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises.

M & L for Non-skid ceramic tiles 7 to 8 mm thick ( square /rectangular) area of each tile exceeding 0.18 sqm but not exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with tile laid over and including screed bed or bedding layer 15 mm thick in CM (1:6), complete all as specified and directed.

All as per description of serial item No. 63 above but as in vertical surface such as skirting, dados, steps etc and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed plaster 10mm thick in CM (1:4) on stone masonry surfaces complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour single piece extruded PVC profile reinforced with MS square tube in opening as per specifications.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with plain colour single piece extruded PVC profile ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour single piece extruded PVC profile for top rail lock rail bottom rail on either side and as gap insert for Top rail and bottom rail paneling of plain colour PVC sheet to fitted on the MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement.

S&F powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat, complete all as specified & directed.

S&F Anodised aluminium door shutters powder coated, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified.

Excavation in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes etc not exc 10 Sqm on plan and getting out in soft/loose soil complete all as specified.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil complete all as specified.

M&L for PCC 1:4:8 type D2 using 40 mm graded crushed stone aggregate in foundations, filling and mass concrete complete all as specified.

M&L for reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.

All as per serial item No. 73 here-in-before but 6 to 10mm dia in stirrups, spacers and binders.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in columns, pillars, piers, posts, struts and the like.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in foundations including rafts, footings, foundation beams, bases for columns, mass concrete and the like.

Wood work (Form work): Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or polygonal for rough finished flat surfaces of concrete.

M&L for 16 to 18mm thick black Granite (of any type) slab as in facing of pillars, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing as per local trade practice over & including 15mm thick screed plaster in CM 1:4, complete, all as specified & directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc

S&F Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required

S&F mild steel framed work as in doors or gates of approved pattern, ornamental and intricate design of angle or other section conforming to Grade E-165 (Fe 290) with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing, ), complete all as specified & directed.

Excavation in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering, and removing surplus soil to a distance not exc 50 m and making good surface in soft/ loose soil complete all as specified & directed.

M&L for PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate in foundations, filling and mass concrete complete all as specified & directed.

S&F mild steel work as in angle iron in posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc) and similar works conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

Supply only mild steel galvanized chain link fencing 3 mm dia of mesh wire, mesh size 50x50 mm complete all as specified and as directed. Note:- Flat iron, round bars, nut bolts and washer shall be measured and paid for separately. Make :- TATA (Wiron)/JINDAL

Fixing only mild steel galvanized chain link fencing, any mesh, size and type to any type of standards, rails, straining bolts etc. including provision of binding wire.Note :- Supply only chain link fencing shall be measured and paid for separately.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil.

M&L for cement concrete 1:2:4 type B0, using 12.5mm graded crushed stone aggregate as incoping or mud stops, rounded or chamfered on edges all as specified.

S&F Plain mild steel wire, 4 mm dia, galvanised class 3, for fixing chain link fencing etc complete all as specified & directed. Make: TATA (Wiron)/Jindal

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc 5 cm long and dia of neck 5 to 10 mm complete all as specified.

S&F galvanized 2 strand, steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossing with and provision of galvanized mild steel wire, staples or steel pins etc as directed. Note :- Each line of horizontal / vertical / diagonal wire to be measured for the purpose of payment. Make: TATA (Wiron)/Jindal

Dismantling RCC posts or struts any section, including taking out embedded portion and making good disturbed groun complete all as specified & directed.

Dismantling fencing wire mesh, any type complete all as specified & directed.

S&F informatory sign board of required size and each sign board shall be made of 4 mm thick aluminium panel (ACP) one side face fully covered with 3M scotchlite brand intensity prismatic grade retro-reflective sheeting as per ASTM D 4956 type IV in required colour. The retro reflective sheet shall be processed on ACP by 3M equipment heat lamp vacum applicator and letter, sign and simble shall be cut by computerised plotter or digital printed on retro reflective sheet with high quality echo solvent digital Rolland and fabricated out of high intensity prismatic grade sheeting with text matter (as required) and border of same sheeting. Sign board shall be supplied along with supported circular hollow stainless steel section frame of size 20mm dia 1.29 mm thick alongwith proper clamping with same section of stainless steel and nut bolt/welding, outer side size of board 1.2mx0.6m hollow section frame pipe 60mm dia 1.29mm thick, board height from ground level to top 2.50m including necessary excavation, PCC complete, all as specified & directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fittings such as switches, ceiling roses, holders, regulators, sockets etc., removing materials from site and making good disturbed surface of walls, floors etc.

Disconnecting unserviceable sub main wiring/service connection of any size and including steel conduit and accessories and removing from site and making good the disturbed surfaces.

Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc.

M&L for point wiring with 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed cable in and including PVC rigid non metallic conduit medium grade not less than 20mm dia ISI marked and fittings and accessories concealed in walls/roof/ ceiling with suitable size of sunk type pressed steel modular terminal box and modular white cover plate with frame of suitable module as per site requirements for mounting of modular switches, sockets, fan regulator etc and one green colour cable of 1.5 Sqmm. (nominal area) single core PVC insulated 1100 Volts, grade multi stranded FRLS copper conductor unsheathed as earth wire up to common earth and connected to earth for the following, complete all as specified and directed:

One light point/fan controlled by one way 5 Amps SP switch

One 5 pin 5 Amps socket outlet on same board with other switch

One 5 Pin 5 Amps socket outlet on independent board with other switch.

All as per serial item No 99.00 above but with 2.5 Sqmm cross sectional area electric cable for 15 Amp socket outlet on independent board, complete all as specified and directed

S&F modular switch 1 way 6/10 Amp , 1 module, complete all as specified and directed.

S&F modular switch 1 way 16 Amp, 1 module, complete all as specified and directed.

S&F modular socket 6 Amp, 2/3 pin combined, 2 module complete all as specified and directed.

S&F mdoular socket 6 Amp/16 Amp, 2/3 pin combined 2 module complete all as specified and directed.

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm.

Taking down existing exhaust fan & wall mounted fan and re use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed

S&F ventilating fan 450 mm sweep suitable for 230 Volts, Single phase 50 Hz AC supply including connecting with three core flexibale copper cable and making opening in existing wall complete all as specified and directed. Make: Havells Turbo Force SP, Usha, Bajaj.

S&F wall mounted fan 600 mm sweep, metal body suitable for 230 Volts, Single phase 50 Hz AC supply including connecting with three core flexibale copper cable complete all as specified and directed. Make: Havells Turbo Force, USHA, Bajaj.

M & L for submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 2.5 sqmm multi stranded copper conductor cable drawn through and incl 25 mm dia PVC non metallic rigid concealed conduits and the conduits accessories incl one run of green colour earth continuity conductor with 2.5 sqmm multi stranded copper conductor cable.

M & L for submain wiring with two single core PVC insualated, unseathed, FRLS, 1100 volts grade 6 sqmm multi stranded copper conductor cable drawn through and incl 25 mm dia PVC non metallic rigid concealed conduits and the conduits accessories incl one run of green colour earth continuity conductor with 6 sqmm multi stranded copper conductor cable.

S&Fas in replacement asymmetrical LED flood light, 145 watt, 415 Volt, 50 Hz, energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium flood light with high power LEDs as light source, IP-65, PDC, LED Highbay with circular form factor and available in both Narrow & wide beam optics options of toughened glass and also suitable to rough services/installations. Make : Havells cat No BY415P LED 145S CWHE WB FG PSU GR XTFCL S5/ Philips/ CG/ Bajaj.

Taking down MCB DB's complete with MCB's/Isolator etc removing materials from site and making good disturbed surface of walls, floors etc and re use at site or carrying to the store(To be measured only when found serviceable in all respects complete for re use.) complete all as specified and directed.

Taking down and Supply and fixing of Change over Three Pole Neutral AC 63 Amp, with bolted type fuse in sheet enclosure with fuses complete all as specified and directed.

S&F MCB distribution board TPN 4 way, 415 volts, double door, with 200 Amps rated bus bar, neutral bar with shrouds, earth bar, IP-43 , made out of sheet steel enclosure, recessed type, factory made powder coated suitable for housing MCBs as incomer and outgoing including blanking plate complete all as specified and directed.

S & F MCB SP, 240 volt, 6 Amp to 40 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F MCB SP, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S & F MCB SPN, 240 volt, 63 Amp capacity, 10 KA, 'C' curve complete all as specified and directed.

S&F MCB TPN, 415 volt, 63 Amp capacity,10 KA, 'C' curve complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm, PVC insulated, unsheathed, multi stranded copper conductor single core FRLS cable, IS-694 (ISI marked), drawn through and including non metallic rigid PVC concealed conduit 20mm dia or higher complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc./ fittings ISI marked and sunk type pressed steel anodised terminal box 1.2 mm thick with bakelite laminated sheet top cover 3 mm thick( Make - Hylem/Anchor) ISI Marked, brass screws and cup washers including 1.5 Sqmm multi stranded copper conductor PVC insulated green in colour as continous earth conductor connected to common earth and earth dolly with all accessories complete all as specified and directed for:- Make of wire- Havells/Polycab/Anchor/Finolex. Make of PVC conduit -AKG/Plaza/Kalinga

One light point/bell point controlled by one, one way switch.

One ceiling fan/exhaust fan point controlled by one, one way switch.

One three pin 5 Amp socket on same board with other switches.

One 3 pin 5 Amp socket on independent board.

All as per item No. 119.00 here-in-before but with 2.5 Sqmm wire, for one 5 pin 5/15 Amp socket on independent board including 2.5 Sqmm stranded copper conductor (FRLS) PVC insulated green in colour as continous earth conductor connected to common earth.

S&F sub main wiring with two runs of single core PVC insulated and unsheathed multistranded (FRLS) copper conductor cable of size 4.00 Sqmm LT, 1100 volts grade, drawn through and including 25 mm dia or higher PVC non metallic concealed conduit with accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc. and fittings and one run of 4 sqmm single core multistranded copper conductor cable green colour as earth continuity conductor. Make of wire- Havells/Polycab/Anchor/Finolex. Make of PVC conduit -AKG/Plaza/Kalinga

S&F Switch piano, flush type, single pole, one way, 5 Amps, 240 volt, 50Hz, AC, complete all as specified and as directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F switch piano flush type 15 Amps, single pole one way 240 volts complete all as speciied and directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F Socket outlet 3 Pin 5/6 Amp flush type complete all as speciied and directed by engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F socket out let 2 in 1,multipurpose 3 pin 15/16 Amp flush type complete all as speciied and directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F ceiling fan regulator electronic flush , steped type (four step) 230 Volts AC complete all as speciied and directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F ceiling rose surface bakelite 3 terminals 63.5 x 17 mm complete all as speciied and directed by engr-in-Charge . MAKE:-Havells/Anchor/Legrand

S&F lamp holder PVC/polycarbonate type with back plate complete all as speciied and directed by Engr-in-Charge. MAKE:-Havells/Anchor/Legrand

S&F LED lamp 10 watt suitable for 230 volts , 50 Hzs, B-22 base complete all as specified and directed

S & F LED light fitting 1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge. Make Bajaj/Havells/CG

S&F LED lights fittings 1x20Watt ,220V, AC decorative box type with driver ,holder including LED tubelight connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F recess mounted LED light fitting 36 watt 2'x2' fabricated CRCA sheet housing duly powder coated with high efficient LED & glare free full opal diffuser, IP20 complete with LED driver. Make : Halonix cat Part no. HLFPR22-02-36-CW-R-HL1

S&F LED tube light fitting in acrylic linear tube 1x 18 watt, 230V complete with bipin holders,LED power driver, connector block, and LED Tube 18 watt.

Supply and fixing testing and commissioning energy saving street light luminaire 15 watt LED , pressure die cast housing with epoxy powder coated with colour finish and prismatic poly carbonate coverlic cover complete with individual LED lences and complete all as specified and directed.

Supply and fixing street light bracket made of 32 mm GI pipe , 1.2 mtr length fixed with two nos of clamp , nut and bolts complete all as specified and directed.

Taking down existing ceiling fan , dismantling blades and refixing after cleaning including conecting up with three core flexible cable from ceiling rose to fan.

S&F MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 8 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed. Make:Legrand/Schneider/Seimens. Note: MCB DB and MCB SP/SPN will be of same make.

S& F MCB distribution board single pole & neutral with 200 Amps rated bus bar, double door IP-43 DB's , made out of sheet steel enclosure, recessed type, factory made powder coated 4 way, 240 volts suitable for housing MCB's including blanking plate complete all as specified and directed. Make:Legrand/Schneider/Seimens. Note: MCB DB and MCB SP/SPN will be of same make.

M & L for earthling complete with GI earth plate electrode 60 cm x 60 cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level connected to GI lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electric plate No 3 of SSR Part-I connected to continuous earth wire on main switch board all as specified or indicated and testing on completion including provision of earth wire protection by 15 mm dia medium grade GI pipe and watering pipe shall be 20 mm bore, medium grade including excavation & earth work in any type of soil & disposal of soi, providing alternate layers of charcoal and common salt, constr of PCC earth chamber in mix 1:3:6 type C-1 with 40mm thick RCC 1:2:4 type B-1 cover, reinforced with 8mm TMT bars 100mm C/C both ways with life hook made out oof 8mm dia bars, watering arrangement with funnel & wire mesh, complete all as specified and directed. Note. The unit rate includes for protection pipe and GI wire 4.00mm from top of earth plate up to 7.5 meter above ground level.

M/s SUNIL ENTERPRISES

M/S Nexus Projects