Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹36.7 LAccepted-AOC | L1 | Accepted-AOC Lowest amount quoted | |
| 2 | L2₹37.6 L+₹69,832.10 (1.89%)Rejected-Finance | L2 | Rejected-Finance Higher amount quoted | |
| 3 | L3₹40.8 L+₹3.8 L (10.4%)Rejected-Finance | L3 | Rejected-Finance Higher amount quoted | |
| 4 | L4₹41.8 L+₹4.9 L (13.3%)Rejected-Finance | L4 | Rejected-Finance Higher amount quoted | |
| 5 | L5₹42.4 L+₹5.4 L (14.7%)Rejected-Finance | L5 | Rejected-Finance Higher amount quoted |
Tender Value
₹46.9 L
EMD Value
₹93,760
Closing Date
8 Dec 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
CWE PUNE
HEADQUARTERS COMMANDER WORKS ENGINEERS GEN CARIAPPA MARG, PUNE-411 001
81716SPECIAL REPAIR / REPLACEMENT OF JCOs MESS BLDG AT NDA KHADAKWASLA.
2022_MES_560720_1
81716SPLREPTOJCOSMESSATGENDA
Open Tender
Civil Works
Item Rate
183 days
GE NDA Khadakwasla
As per Tender
9 documents required · 9 mandatory
₹500
GE NDA Khadakwasla
₹93,760
Yes
31 Jan 2023
1 Nov 2022
10 Dec 2022
1 Nov 2022
8 Dec 2022
26 Nov 2022
Amount
Dismantling floor or wall tiling of any description and size including cement mortar bedding (but not backing), removing rubbish off the premises complete all as directed.
Demolition of Stone slabs and tiles of any description or thickness (laid, beded & pointed in any mortar) in floors, aprons etc including cleaning off premises where directed by Engr-in-charge.
Taking down cement plaster on brick or stone walls etc including raking out joints,hacking for key ,scrubbing down with water etc complete all as specified and as directed.
Demolition of unreinforced cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including cleaning off premises where directed by Engr-in-charge.
M&L for 75 mm thick PCC (1:4:8) type D2 using 40 mm graded crushed ston aggregates as in sub base all as specified and directed including necessarry form work complete all as specified and as directed.
M&L for light colour non-skid ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) in floors etc, area of each tile exc 0.11 sqm and n. exc .18 sqm, set and jointed in neat cement slurry and pointed in coloured cement to match over and incl 15 mm thick screed bed or bedding layer in CM (1:4) complete all as specified and as directed.
M&L for Coloured Glazed ceramic tiles in vertical wall surfaces 350 x 250 mm x 7 mm / 450 X 350 X 7mm thick set and jointed in neat cement slurry and pointed in white or color cement to match, laid over and incl provn of 10 mm thick plaster in CM (1:3) complete all as specified and as directed.
M&L for joint free coloured ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.
M&L for 18 to 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and incl 20 mm thick screed bed or bedding layer in CM (1:4) complete all as specified and as directed.
M&L for 18 to 20 mm Granite (of any type) work (table rubbed and polished) for on vertical surface as in skirting / dado over and including 12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.
M&L for Machine cut cuddapa stone slab 20 to 25 mm thick on vertical surface as in skirting over cement screed basein CM 1:6 ,laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing complete all as specified and as directed.
M&L for Hand cut superior quality Kota stone slab flooring 20-25 mm thick over cement screed , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete match including bulnosed to edges complete and incl 20 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed by Eng-in-charge.
S&F glossy finish Chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick, set, jointed and pointed in neat cemeant slurry in floors with grey cement and pigment over and including 20 mm thick cement screed in CM (1:6) complete all as specified and as directed.
M&L for glossy finish machine pressed precast conctete interlocking paver block with grey cement and pigments any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade incl 50 mm thick sand chusioning complete all as specified and as directed.
M&L for 100 mm thick PCC (1:2:4) type B-1, using 20 mm graded crushed stone aggregate & Finishing cement concrete surface even and smooth without using extra cement all as specified and as directed.
M&L for complete removal of existing water proofing treatment of any decription and layers from wall,roof,chajja's,gabble walls, edges (at any height )etc incl any number of screed bed or bedding layer of mortar if any complete and cleaning the surface free from dust and mud ,scrubbing down with water complete all as specified , cleaning off the premises all as directed by Engr-in-charge
Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as directed.
Demolition of concrete in Roofs, floors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work complete all as specified and as directed.
M&L for providing PCC (1:2:4) type B0 (using 12.5 mm graded crushed stone agg) as in roof kerbs and mud stope rounded or chamfered on edges complete all as specified and as directed.
M&L for cement concrete type B0 , 1:2:4 using (12.5 mm graded crushed stone aggregate) in roof padding complete all as specified and as directed .
M&L for PCC 1:2:4, type B1 using (20 mm graded crushed stone aggregate) in copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, in gabble walls including necessary formwork complete all as specifie and as directed.
M&L for Rendering 20 mm thick in cement mortar 1:4 on concrete surfaces using integral water proofing compound as per manufacturers instructions finished even and smooth without using extra cement (at any respective height of bldg ) complete all as specified and as directed. (Note : Water proofing compound shall be measured & paid saparately)
Supply only integral water proofing compound (ISI) marked complete all as specified and as directed.
M&L for cutting grooves in brick / stone wall, 75 mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as directed.
M&L for APP based modified pre fabricated five layer 3 mm thick and weighing not less than 3.6 kg / sqm water proofing membrane reinforced with polyester non woven fabric mat with 150 gm / sqm black finished with compatible primer conforming to IS 3488 @ 0.30 ltr/ sqm and bonding material 85/25 bitumen 1.2 kg / sqm before and after laying membrane laid by torch application side overlap of 75 mm and over lap of 100 mm longitudinally, at the junction of gabble wall a grove of 75 mm wide and 65 mm deep and shaping horizontal of groove with 1:3 with bituminous mastic joints / overlap shall be sealed with hot bitumen 85 / 25. Two coats of bituminous aluminium paint over membrane shall be carried out all as spcified and as directed.
Dismantling of old cast iron / PVC / AC 100 mm bore pipes jointed in cement motar or fixed to wall or floor complete all as specified and as directed.
S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or floor incl stack clamps complete all as specified and as directed.
S&F 110 mm dia PVC (SWR) bends any radius complete all as specified and directed by Engineer -in-charge.
S&F 110 mm dia PVC (SWR) bends with access door complete all as directed.
M&L for core cutting of upto 150 mm dia, n exc 600mm deptth in stone wall and making good disturbed surfaces and filling the remaining area with cement concrete (1:2:4) type B-1 using 20 mm graded crushed stone aggregate all as specified and directed.
Demolition of brickwork or stone / boulder masonry, build in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and as directed.
M&L for block masonry with solid blocks of precast cement concrete class designation C-5 (using 20 mm graded crushed stone aggregate), exc 10 cm in width and setting in cement mortar (1:6) complete all as specified and as directed.
M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 complete all as specified and as directed.
M&L for racking out joints work built in cement mortar to random or polygonal rubble uncoursed or brought upto course and Flush pointing to random or polygonal rubble, uncoursed on brought upto courses in CM 1:3 in floor and wall complete all as specified and as directed.
Dismantling of single layer of manglore/ Similar pattern tiles in roofing complete all as directed.
Dismantling of battens of tiles of any size and description spaced exc 15 cm, including tiling fillets complete all as directed.
Dismantling of unframed work timber scantlings 40 sq. cm and over in section, in any position
All as per item No 37 here- in- above but in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section.
Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as directed.
S&F Galvanised corrugated mild steel sheeting 0.63 mm thick with two corrugations side lap, fixed with 'L' type or 'J' type of cranked hook in lieu of screws and washers in roofs, walls etc with grade of zinc coating 275 complete all as specified and as directed.
S&F Galvanised plain mild steel sheeting 0.63 mm thick in Ridge, hips, valley gutter, drip and straight flashing (length and girth as fixed) with grade of zinc coating 275 complete all as specified and as directed.
S&F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with L hooks or J types or cranked bolts complete all as specified and as directed at site Note : Work to be execute in any respective ht of building.
M&L for Pre painted galvalume aluminium zinc coating GI based Plain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified Note : Work to be execute in any respective ht of building.
S&F MS rolled /box sections as in main and cross beams ,columns ,purlins, brackets where connected to common rafters ,fixed with angle cleats or other connecting plates ,Fe 410 W ,GRADE E- 250/ box sections complete all as directed.
M&L for MS Plates,FE 410W,Grade E-250 (plain or chequred) channels,square cut or notched(ordinary and counter sunk) forming holes with riveted, bolted or welded attachment complete all as specified and as directed.
Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and directed by Engineer-in-Charge.
M&L for wrought 2nd class hard-wood in timber fiixed scantlings in repairs, to replace old and decayed timber (including piecing, scarfing, etc., of old and new timbers if required) and removing defective portions to store complete all as directed.
M&L for clean sawn ,2nd class H/W tile battens at 30 cm centres, exe 5 and n.exe 15 sqcm sectional area complete all as specified and as directed.
All as per item No 48 here- in- above but except battens complete all as specified and as directed.
M&L for preparing tile battens of any size and spacing and treated all over (measured overall on one side only spaces not deducted) with two coats of cresoting oil etc specified and directed by Engr-in-charge.
M&L for providing roof tiles Manglore pattern interlocking at side joints, laid dry (at any height of bldg) complete all as specified and as directed.
All as per item No 51 here- in- above but except tiles complete all as specified and as directed.
M&L for ridge or hip tiles to suit mangalore pattern of roofing tiles, bedded and jointed in CM (1:6) complete all as specified and as directed.
S&F eaves boards 2nd class hardwoood clean sawn in roof 20 mm thick fixed with nails in any situation complete all as specified and as directed.
M&L for preparation of new wooden surfaces and painting two coats of synthetic enamel paint over and including a coat of pink primer complete all as specified and as directed..
M&L for preparation of old painted surfaces of wall by completely removing existing treatment by scrapping , cleaning , washing with water etc , and applying Two coats of oil bond distember including filing the surface with crack filler wherever required all as specified and directed . Note :- (i) The coulour scheme of the painting will be as decided by the accepting officer (ii) work tobe execute under occupation conditions.
M&L for preparation of old painted surfaces of ceiling by completely removing existing treatment by scrapping , cleaning , washing with water etc , and applying Two coats of oil bond distember including filing the surface with crack filler wherever required all as specified and directed . Note :- (i) work tobe execute under occupation conditions.
M&L for 3 mm thick wall care putty on wall complete all as specified and directed by Engr-in-charge.
M&L for 3 mm thick wall care putty on ceiling complete all as specified and directed by Engr-in-charge.
M&L for Preparing old painted plastered / concrete surfaces of wall and applying two coat of synthetic enamel paint complete all as specified and as directed.
Preparing old painted wooden surfaces wall / ceiling exc. 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and as directed.
Preparing old painted steel surfaces exc.10 cm width or girth and applying two coat of synthetic enamel paint , including grills, gate complete all as specified and as directed.
M&L for preparation of old painted surfaces of wall , cleaning , washing with water etc , and applying two coat of exterior emulsion paint (Appex paint) , including filing the surface with crack filler wherever required all as specified and directed . Note . (i) The coulour scheme of the painting will be as decided by the accepting officer (ii) Work to be execute in any respective ht of building
M&L for French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on old works with two or more coats complete all as specified and as directed.
Excavating in post holes (or similar holes) each n. exc 0.5 cum getting out returning in and ramming earth or broken rubble mixed with earth around in layer not exc 25cms watering and removing surplus soil to a distance n.exc 50 m and making good surfaces in any hard and dense soil complete all as directed.
M&L for PCC (1:2:4) type B2 (using 40 mm graded crushed stone aggregate) in foundation , filling and mass concrete complete all as specified and as directed.
S&F rolled mild steel angle iron posts for fencing posts and struts split at bottom including flat iron 40 x 4 mm with necessary welding with drilling bolting or rivetting etc and similar work conforming to Fe 290 Gde E-165 complete all as specified and as directed.
S&F mild steel round bars , 10 mm dia and over cut to length , bent to shape as in staining to fencing (Fe -410w-E-250 quality A) complete all as specified and as directed.
Fixing only Chain link MS gavanised fencing any size ot type including line wires, any mesh, size and type of standard, rails, straining bolts etc including provision of bunding wire complete all as directed..
Supply only chain link MS galvanised fencing, 50 mm x 50 mm size with 3 mm dia wire complete all as specified and as directed.
M&L for two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel/iron surface of any description over 10 cm in width or girth complete all as specified and as directed.
M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and as directed.
M&L for Providing precast cement concrete 1:2:4 type B0 (Using 12.5 mm graded stone aggregate as in louvres and jallies, 25mm thick (measured :solid), including all mould- ings set in cement mortar 1:6 complete all as specified and as directed.
M&L for preparation of new painted surfaces of wall , cleaning , washing with water etc , and applying two coat of exterior emulsion paint (Appex paint) over and including a coat of primer and filing the surface with crack filler wherever required all as specified and directed . Note . (i) The coulour scheme of the painting will be as decided by the accepting officer (ii) Work to be execute in any respective ht of building
Dismantling boarding, any description, fixed any position with nails / screws complete all as directed.
S&F Solid PVC Wall Lining / Panelling consisting of 5 mm thick Plain colour PVC sheet inclusive of solvent cement and incl supply and fixing PVC frame / PVC Strips as per manufacture specifications and drawing.
M&L for 5 mm thick PVC sheet fillet of width 35 mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.
Taking down chowkhats or frame not exc 1.5 sqm each with shutters (without taking off shutters from the frames) complete all as directed.
Taking down chowkhats or frame not exc 1.5 sq. m but n exc 4 sq m each with shutters (without taking off shutters from the frames) complete all as directed.
Taking down shutters exe 1 sqm and n.exc 2 sqm each and removing complete all as directed.
Hacking out old broken glass(any thickness, size, quality or discription) from wooden frames or stone, concrete or brick surrounds , glazed with putty or fixed with beads complete all as directed.
M&L for Solid PVC door frame of size 50 x 47 mm ,made out of 5 mm plain colour PVC sheet re inforced with MS square tube ,supplying and fixing in opening as per specification and drawing.
S&F Factory Made Solid PVC Moulded Door Shutters With Particle Board Core 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2 mm thick Moulded PVC Sheet on the front Face & 2mm Plan colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed by Engineer-in-charge
S&F 2nd class hard wood Plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed incl cutting holes and hold fasts fixing (split at one end) complete all as specified and as directed.
S&F 35 mm thick Factory made 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all asspecified and as directed.
M&L 2nd class hardwood 35 mm thick Factory made Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all asspecified and as directed.
S&F 30 mm thick 2nd class hardwood skelten shutter glazed and skelton open rebated and prepared to receive glass with divided into squares with plain chamfered or rounded mitered and rebated sash bars any nubmers fitted with cut and mitered beads for securing glass size of members of windows, ventilators, etc. are provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24(b) complete all asspecified and as directed.
S&F Anodised aluminium frame powder coated for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. complete shall as specified.
S&F Powder coated anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified and as directed.
S&F Powder coated anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all asspecified and as directed.
S&F Powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.) suitable handle (1 no.) complete all asspecified and as directed.
S&F 1st class soft or hard wood beads, straight any size for glassed or gauzed joinery, renewed including powder coating of any colour or powder coating not less than 50 micron mitres etc complete all as specified and directed by Engr-in-charge.
S&F for 20 mm thick 2nd class hard wood Boarding, with nails in any situation (except flooring and skirting,) planed one side with butt joints In repairs to replace old and or decayed boarding in patches including cutting out old, piecing, heading joints, etc
S&F 100 mm butt hinges cold rolled mild steel medium weight and fixed complete all as specified and as directed.
S&F 100 mm Aluminium handles, cast type, anodised complete all as specified and as directed.
S&F 150 mm Aluminium handles, cast type, anodised complete all as specified and as directed.
S&F 75 mm butt hinges cold rolled mild steel medium weight and fixed complete all as specified and as directed.
S&F Aluminium anodised barrel tower bolts of extruded section 100 mm long complete all as specified and as directed.
S&F Aluminium anodised barrel tower bolts of extruded section 75 mm long complete all as specified and as directed.
S&F for Aluminium anodised, barrel tower bolts 150 mm long of ex- truded section and fixed complete all as specified and as directed.
S&F 300 mm long aluminium alloy, anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections complete all as specified and as directed.
S&F in repairs 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & directed also including taking down old one.
M&L for preparation of new wooden surfaces and painting two coats of Synthetic Enamel paint over a coat of pink primer complete all as specified and as directed.
S&F Sheet glass 3 mm thick ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and as directed.
S&F 4 mm thick Figured glass, pin head type and glazing with oil putty in squares in exc 0.5 sq.m in each pane complete all as specified and as directed.
S&F Stainless steel wire cloth. 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples including taking out wooden beads and incl re-fixed new in the same position complete all as specified and as directed.
S&F Harrison rails 20 mm dia, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified and as directed.
S&F T type brackets decorative type powder coated suibable for 20 mm dia complete all as specified and as directed.
S&F Aluminium (extruded section body) Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified and as directed.
Taking down up or down steel tubing and connections incl cleaning for re-fixing or removal to stores ,15 mm dia pipes complete all as specified and as directed.
All as per item No 110 here- in- above but 20 mm dia pipes.
S&F galvanised mild steel medium grade tubes 15 mm dia bore with all fittings and fixed to wall , floor etc. complete all as specified and as directed.
All as per item No 112 here- in- above but 20 mm dia pipes.
Dismantling of existing water tanks Exc 250 not Exc 500 and removing to store.
All as per item No 114 here- in- above but exc 500 Ltr n. Exc 1000 Ltr capacity.
S&F Rotational moulded polye- thylene water storage tanks 500 Ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and as directed.
S&F Rotational moulded polye- thylene water storage tanks 1000 Ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and as directed.
S&F in repair 15 mm dia tank Nipple suitable for HDPE water tank. (Minimum weight 15 mm-38gms/20mm-45gms /25mm- 65gms) including taking down old one as specified & directed.
S&F in repair 20 mm dia tank Nipple suitable for HDPE water tank. (Minimum weight 15 mm-38gms/20mm-45gms /25mm- 65gms) including taking down old one as specified & directed.
S&F in repairs ball brass valve high pressure with polythene float and fly nut complete to bore of pipe 20 mm complete all as specified and as directed.
All as per item No 120 here- in- above but 20mm dia complete all as specified and as directed.
S&F in repairs Bib taps 15 mm dia, chromium plated ,fancy type ,cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed including taking down old one complete all as specified and as directed.
S&F in repairs Stop valves 15 mm dia, chromium plated ,fancy type, cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed including dismantling of old one complete all as specified and directed by Engr-in-charge.
S&F Brass CP mixer 15 mm dia for mixing hot & cold water screwed down for iron pipe and fixed
S&F for Brass chromium plated shower rose 125mm size complete as directed and sample to be approved by Engr-in-charge.
S&F in repairs for PVC flushing cistern valve less, syphonic action type low level, ball valve, float and handle with bracket fixed in repair of 10 ltrs capacity all as specified and directed including taking down old one.
S&F for Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern including necessary cutting to floor tiles and connection to WC complete all as specified and directed by Engr -in-Charge.
S&F PVC connection 15mm size with PTMT nuts of length 600mm.
S&F Stainless steel sink without drainage board, 1.00 mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever castiron brackets, connecting union etc. overall size 495mm x 420mm with bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed.
S&F in repair Vitreous China wash basin, white, flat back, size 550 x 450 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and as directed.
S&F in repair Water closet (Squatt pattern) vitreous China squatting pan, ‘Orissa’ pattern, size 580 x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) connection to trap and squatting pan including P' trap set in and including concrete etc. complete all as specified and direted by Engr-in-charge including making good to floor.
S&F in repair wash down water closet (Pedestal pattern), white incl traps and all fittings complete all as specified and as directed.
S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed , screwed for iron pipe of bore 15 mm fixed in repairs.
S&F PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.
S&F in repair Waste coupling of PTMT (half or full threaded) (Minimum weight 40 mm-45gms/40mm-60 gms) for 32mm bore dia pipe complete all as specified and as directed.
S&F in repair Waste coupling of PTMT (half or full threaded) (Minimum weight 40 mm-45gms/40mm-60 gms) for 40mm bore dia pipe complete all as specified and as directed.
S&F towel rail 600 mm long of CP brass, fixed with chromium plated brass screws and wooden/plastic cleats all as specified.
S&F Low density polyethylene (LDPE) pipes 40mm dia of pressure rating 6kgf/sq. cm complete all as specified and as directed.
S&F doom grating 100 mm dia of PTMT (Minimum weight 25gms) complete all as specified and as directed.
S&F Grating doom 125/100 mm dia with waste hole of PTMT. (Minimum weight 40 gms) complete all as specified and as directed.
S&F Soap dish any type fixed to plugs with chromium plated brass screws minimum size 160x160x90mm complete all as specified and as directed.
M&L for unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe 50 mm bore of pipes complete all as specified and as directed.
S&F in repairs Gun-metal, globe or gate valves 15 mm dia, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and direceted by Engr-in-charge.
S&F in repairs Gun-metal, globe or gate valves 20 mm dia, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and direceted by Engr-in-charge.
Excavation in trenches n. exe 1.5 m wide & n. exe 1.5 m depth for foundation etc n.exe 10sqm on plan and getting out in Soft / Loose soil complete all as directed.
Excavation in trenches n. exe 1.5 m wide & n. exe 1.5 m depth for foundation etc n.exe 10sqm on plan and getting out in hard/ dense soil complete all as directed.
Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as directed.
Demolition of brick work or stone masonary built in CM and cleaning off premises complete all as directed.
Demolition and breaking up drain pipes ( SWG,AC or RCC pipes ) set in CM 150 mm dia complete all as directed.
Demolition and breaking up drain pipes ( SWG,AC or RCC pipes ) set in CM 300 mm dia complete all as directed.
M&L for Cement concrete in foundations, filling and mass-concrete Type D2 1:4:8 (40 mm graded crushed stone aggregate) complete all as specified and as directed.
M&L for providing plain cement concrete 1:2:4 type B1 using 20 mm grade crushed stone aggregate. as in surfaces channels & drains complete all as directed.
M&L for providing plain cement concrete 1:2:4 type B1 using 20 mm grade crushed stone agg. as in coping including weathering slightly, rounded or chamfered angles and throating and necessary use and waste of form work complete all as directed.
M&L for providing precast RCC 1:2:4 type B1 (using 20 mm grade crushed stone aggregate as in cover slabs for manholes set in CM (1:6) all as (Note : Reinforcement shall be measured & paid separately)
S&F for providing mild steel TMT bars 6 to 8 mm dia cut to length bent to shape required includig cranking, bending etc & binding with ms wires (annealed) n. exe 0.9 mm dia complete all as specified and as directed.
M&L for providing bed to drain pipes 150 mm dia in cement concrete (1:3:6) type C2 using 40 mm graded crushed stone aggregate including packing under & haunching against the sides of pipes after they are laid & tested complete all as directed.
All as per item No 157 here- in- above but for 300 mm dia pipes complete all as specified and as directed.
M&L for providing reinforced cement concrete pipes 150 mm dia class NP 2 with collars laid and jointed with cement jointed all as directed by Engr -in -charge.
All as per item No 159 here- in- above but 300 mm dia pipes complete all as specified and as directed.
M&L for cutting into existing manholes for connecting new drains internal dia of pipe 150 mm making good to pipe & rendering cutting out existing benching for forming branch channel (1/2 round or 3/4 section in cement concrete (1:2:4) type B-1, smooth finished .
All as per item No 161 here- in- above but for 300 mm dia of pipe complete all as specified and as directed.
Returning filling in including spreading levelling, watering & well ramming in layers n. exe 25 cm any type of soil complete all as specified and as directed.
Removing excavated material any type of Soil n. exe 50 m and depositing where directed by Engg-in- charge at a level n. exe 1.50 m above the starting point in.
Dismantling of cast iron 100 mm bore pipes jointed in cement motar complete all as directed.
Dismantling of cast iron 75 mm bore pipes jointed in cement motar complete all as directed.
S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or floor complete all as specified and as directed.
S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or floor complete all as specified and as directed.
S&F for 75 mm dia PVC (SWR) bends any radius complete all as specified and directed by Engineer -in-charge
S&F for 110 mm dia PVC (SWR) bends any radius complete all as specified and directed by Engineer -in-charge
M&L for PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in benching in manholes including necessary form work and finishing the exposed surface concrete even and smooth using extra cement complete all as specified and directed by Engineeer-in-Charge.
M&L for plain cement concrete 1:3:6 type C1, using 20 mm graded crushed stone aggregate in plinth protection, 75 mm thick, finished even and smooth without using extra cement, including making joints 12 mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen 85/25 and sand in the propotion of 1:3 by weight complete all as specified and as directed.
Taking down carefully copper/aluminium point wiring light/fan/ socket /power complete (fittings such as switches,ceiling roses,pendents,regulators etc to be measured and paid for separately), removing the material and including making good the distrubed surfaces of the wall flooring ceiling etc to match the existing surface all as specified and directed by Engr-in-Charge.
M&L for Point wiring with 1.5 Sqmm (nominal cross-sectional area) FRLSH PVC insulated & unsheathed 1100 volts grade multi stranded copper conductor single core cable drawn through and including non-metallic rigid PVC casing capping ISI marked not less than 19 mm with all fitting & other accessories and also including PVC insulated ISI marked unseathed FRLS cable size 1.5 sq mm copper conductor as earth wire to common earth dolly including modular cover plate with frame and PVC box suitable for modular type switches, sockets, fan regulator etc for following :-
(a) One light /Fan point controlled by one way switch 6 Amps 240 volts.
(b) One 3 pin socket outlet, 5 Amps on the same board.
(c) One 3 pin 6 Amps socket out let point on independent board.
M&L for point wiring with 2.5 sq mm copper conductor FRLS (multistrand) PVC insulated ISI marked unseathed cable and including surface, Non metalic rigid PVC casing capping type ISI marked not less than 19 mm with all fitting & other accessories and also including PVC insulated ISI marked unseathed FRLS cable size 2.5 sq mm copper conductor as earth wire to common earth dolly including PVC box suitable for 15 Amps socket outlet power point independent circuit .
Taking down carefully Three phase/Single phase sub main wiring of any type and size and making good disturbed surfaces complete as directed.
M&L for sub main wiring with PVC insulated FRLS grade cable LT 1100 Volts grade PVC insulated unsheathed, multistranded with stranded copper conductor drawn through & including surface type PVC casing & caping including drawn on wall/ceiling/through stair case/wooden surface with all accessories and incl cutting of existing surfaces of any type and making good to match with the existing surfaces acrylic sheet work after completion alongwith one contineous earth wire and connected to common earth complete all as specified for following sizes of cable :-
(a) 2 x 4 sq mm with one contineous earth wire of size 4.0 sq mm Note : Two runs of 4 sq mm cable and one run of 4.0 sq mm earth wire and PVC casing/capping will be measured as one meter.
(b) 2 x 2.5 sq mm with one contineous earth wire of size 2.5 sq mm Note : Two runs of 2.5 sq mm cable and one run of 2.5 sq mm earth wire and PVC casing / capping will be measured as one meter.
S&F modular switch 6 amps one way, 1 module.
S&F for modular socket 6A-2/3 pin , 2 module
S&F modular switch 1 way 16A 1 module.
S&F Modular socket 16A 2/3 Pin 2 Module.
S&F 4 Nos 6 Amps Modular switch Socket and 12 Module cover plate fix onTerminal boxes for TV Room/ Bar room / Main Hall.
S&F modular step type fan regulator 120W, 2 module.
Supply and fixing ceiling fan complete with blades, down rods and other accessories, 230 V, 1200 mm sweep with Minimum air delivery of 210 CMM BEE Five star rated with brushless direct current motor (BLDC), white/Ivory in colour all as specified and directed.
S&F 1x18/20W,230V surface and wall mounted LED batten,(single side connection) T8 luminaries with one 18/ 20 Watt LED retrofit T8 polycarbonate tube (single side connction) and including connecting up with twin core twisted flexible copper condctor cable from ceiling rose all as specified.
S&F 10 Watt LED batten suitable for indoor application of color temperature 6500K including connecting with twin core flexible wire of size 1.0Sqmm all as specified. complete all as specified and directed
M&L in repalcement surface mounted LED Panel lights size of 600mm x 600MM x 35mm 40 W LED 5700K, 240Volts and glare free symmetrical illumination suitable for ceiling, Environmental friendly, new generation, energy saving, high power LED as a light source with clear diffuser and separate replaceable electronic driver including connecting with twin core wire and also matching to the adjacent ceiling surfaces carefully all as specified and directed. Note: The quoted price shall be deemed include the cost of Light and its driver.
M&L for surface mounted LED Panel lights size of 178mm x 178MM x 35mm 12 W LED 5700K, 240Volts and glare free symmetrical illumination suitable for ceiling, Environmental friendly, new generation, energy saving, high power LED as a light source with clear diffuser and separate replaceable electronic driver including connecting with twin core wire and also matching to the adjacent ceiling surfaces carefully all as specified and directed. Note: The quoted price shall be deemed include the cost of Light and its driver.
S&F in sheet metal enclosures single pole MCB 20 Amps with a two pin and earth plug and socket complete with all accessaries etc all as directed by Engr-in-charge.
S&F 8 light champagne opal glass with chrome finish Chandlier , model No: KCH-CHR-MD1503300212 of make: Jaquar or equivalent in Bajaj/ Havells Greaves including proper hanging arrangement with brass chain upto reqd height (not more than 4 mtr) all as specified and as directed.
M&L for RJ-11 telephone socket with transparent shutter 1 module alongwith flush metal box 1 module and front cover plate 1 module all as directed.
M&L for PA eqpt socket with transparent shutter 1 module alongwith flush metal box 1 module and front cover plate 1 module all as directed.
M&L for LAN socket UTP Cat with transparent shutter 1 module alongwith flush metal box 1 module and front cover plate 1 module all as directed.
M&L for TV socket with transparent shutter 1 module alongwith flush metal box 1 module and front cover plate 1 module all as directed.
M&L for Earthing complete with galvanised steel earth plate electrode 600 mmx600 mmx6mm thick burried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters deep below normal ground level and filled with alternate layers of charcoal and salt with 15 cm thick layer , connected to galvanised wire earth lead 4 mm dia by means of bolts, nuts, check nuts and washers made of galvanised iron, 20 mm bore GI pipe (med grade) for watering, 15 mm bore GI pipe (light grade) for protection of earth lead, including necessary earth work in any type of soil, Earth pit of PCC (1:3:6) type C1 and precast earth pit cover made of RCC (1:11/2:3) type A1 duly reinforced with 8 mm dia TMT bar @ 150 mm c/c both ways, one lifting handle made of 8 mm dia TMT bar embedded in cover slab complete all as specified and as shown in Electrical Plate No 3 of SSR Part-I including testing on completion.
Taking down unserviceable MCCB DB/MCB DB along with wooden boards of any size complete and making good disturbed surface complete.
S&F factory made epoxy powder coated Distribution Board TP & N 4 way double door (VTPN MCCB DB ) MCCB as In comer, with metal door (IP-43 protection) fabricated from CRCA sheet and fixed semi flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockout semi flush to wall and making good disturbed surface and touch up with the same finishes complete all as specified (Make/Model of VTPN DB : Legrand/L&T/Siemens) Note:MCBs will be measured and paid seperately under respective Sch A item in the schedule
S&F MCB DB 12 way SPN double door sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar,surface mounting complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site as directed by the Engr-in-Charge. Make: Havells/Legrand. Note - MCBs will be measured & paid separately under respective item of sch A, if required to be replaced.
S&F MCB DB 08 way SPN double door sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar,surface mounting complete including taking down the existing DB of any type & size alongwith its accessories by removing from existing circuits and refixing the new DBs and circuits complete as reqd at site as directed by the Engr-in-Charge. Make: Havells/Legrand. Note - MCBs will be measured & paid separately under respective item of sch A, if required to be replaced.
S&F MCB SP 6 to 32 Amps 240V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing. Make : Benlo/C&S/Indoasian
S&F Curve MCB SPN 40 Amps working on 240 volts, 50 HZ,10 KA all as specified and directed. Make : Benlo/C&S/Indoasian
S&F of MCCB 4 pole 63 Amps 10KA breaking capacity,thermal magnetic adjustable of overload & short circuit release as per IS - 13947 & IEC 60947-2.MCCB should be suitable spreaders & phase barrriers for each terminals with all accessories al as specified and directed.AC 415V.Make:Legrand/L&T/Schiender
S&F Stationary type electric water heater closed/vented type , inner body made out of copper of capacity 25 Litres suitable for 230 volts, single phase AC 50 HZ with BEE Star (5 Star Rating) complete with all accessories and fittings as per requirement and depositing old water heater of any type and capacity to MES Store yard complete all as specified and directed by Engr-in-charge. Make: Havells/Racold/Jaquar
Taking down the ceiling fan/Exhuast fan carefully and cleaning/Servicing the fan if any repairs/replacing of parts required complete including painting the fan with enamel spray paint white colored and fixing back the fan with fixing accessoires required at site.
S&F honor board LED (warm white) fitting of 1x12 Watt individual LED lenses, chorme coloured.
S&F high speed wall mounted fan of sweep 400 mm,Full copper motor, auto thermal overload protection,compact style and powder coated guards & pull cord switch for speed regulation and oscillation control including connectng up the power cord to the socket and necessary fixing accessories all as specified and directed.
S&F of Plastic ventilation fan of 250 mm sweep inclduing replacing the plywood as per the site requirement. (Note: Old Exhuast fan should be deposited in MES store yard)
S&F of Metal body ventilation fan of 380 mm sweep inclduing replacing the plywood as per the site requirement. (Note: Old Exhuast fan should be deposited in MES store yard)
M&L for three phase sub main wiring with four single core PVC insulated FRLS cables with stranded copper conductors 4 Sqmm , 1100 Volts grade in and including surface, Non metalic rigid PVC casing capping double lock type ISI marked of suitable size with all fitting & other accessories and two copper cable 4 sqmm continuous earth wire complete all as specified and directed (04 runs of 6 Sqmm cable with 01 run of 6 Sqmm earth wire along with casing caping shall be measured as one RM)
Supply and fix sheet metal Triple pole and earth encolsure with a three pin and earth plug with socket complete with one TPN MCB 32 Amp with all accessaries etc all as directed by Engr-in-charge.
S&F 30 watt LED building security light IP-65 protection made up of die cast aluminium housing with lens covered high power LED as lighting source and including suitable GI medium grade bracket complete all as specified and directed by Engr-in-charge. Note: Quoted rate shall be deemed including of LED fitting and GI medium grade bracket.
Supply, installation, testing and commissioning in repalcement of LT Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, front side double door type with locking arrangement for front side and Nuts, bolts for back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with aluminium bus bars, electrolytic grade of 300 Amp Current rating. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and Cable connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers including suitable Lugs etc. The panel shall be provided with digital multifunction meter 4410 Series, Accuracy Class 1 with RS 485 Parameters with cast Resign CTs and RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be showing the arrangements of circuit shall be pasted inside the panel door and covered with transparent laminated plastic sheet . The panel shall be provided with manufacturer's name plate, skull & bones danger notice board etc. The panel shall be provided 4 Nos 50x50x6mm thick angle iron supports of not less than each 1 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both sided and suitable extended rotary handle for all Incoming/Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1800mmX400mmX1200mm (LxWxH). The panel shall be provided for Cable entry from bottom side for each MCCB/ MCB Cable, size up to 95 Sqmm 3.5 C with suitable size of SS Cable Glands including 2 Nos of Earting Terminals one on each side of the Panel with earth strip and including following accessories:-
Note : Before manufacturing drawing and design of panel including size & length of busbar shall be approved by Engr-in-charge.(a) MCCB 4 Pole, 415 Volts, 160 Amp, 25 KA breaking Capacity with adjustable thermal and adjustable Magnetic overload protection with Ics = 100% of Icu including both side of spreader links and phase separator etc. (Incoming) - 01 No.
(b) MCCB 4 Pole, 415 Volts, 63 Amp, 25 KA breaking Capacity with adjustable thermal and adjustable Magnetic overload protection with Ics = 100% of Icu including both side of spreader links and phase separator etc. (Outgoing) - 02 Nos.
Supply and Laying in trenches including testing and commissioning LT UG Power cable, XLPE Insulated, screened, PVC bedded, galvanized steel strip armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor including termination with LT Panel/Feeder Pillar with galvanised or Cadmium plated high tensile nuts, bolts and washers etc including clamping on any type of wall with suitable size of GI Clamps, nuts, bolts & washers etc complete all as specified and directed of following size :-
(a) 3.5 Core 50 Sqmm
(b) 3.5 Core 25 Sqmm
(a) 4 Core 16 Sqmm
Excavation in trenches, n.exc 1.5m wide and n. exc 1.5 m depth and getting out in for foundation of pole, stay, laying of cable and pipe etc :
(a) Hard/dense soil
(b) Soft/disintegrated rocks
Returning and filling in, including spreading and well ramming in layers n exc 25 cm all as specified and directed.
Removing excavated material a distance n. exc 50 m & depositing where directed at a level n. exc 1.5 m above the starting point.
M&L for dry sand for cushioing to under ground cable intrenches incl spreading, leveling and hand punning complete all specified. Note : For measurement purpose punned thickness shall be considered.
Supply and Laying un-reinforced precast concrete cable cover, class LV, Type 1, flat, size 250mm x 150mmx 40mm for protection of cable from mechanical damage complete all as directed.
M&L for Road Cutting as required for laying pipe/cable etc including earthwork and necessary excavation including making good with required material to match with the existing one or with PCC 1:2:4 type B1 complete all as specified and as directed by Engineer-in-charge.
M&L for tubes, Light Grade, galvanised with all fittings, laid in trenches for protection of Cable for Road/Path Way Crossing etc of 50mm dia size complete all as specified and directed by Engr-in-Charge.
M&L for earthing complete with galvanized steel earth plate electrode 600 X 600 X 6.3 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.50 m deep below normal ground level in any type of soil strata, connected to galvanized iron strip 32 x 6mm by means of bolts, nuts and washers of galvanised iron or steel all as shown in earth plate No 3 of MES schedule 1991 Part – I connected to Change over switch panel including necessary excavation and earth work, concrete pit & chamber in PCC 1:2:4 type B1 & pit cover including with lifting handle and Earth lead and 20mm Dia GI watering pipe medium grade, Funnel, wiremesh, etc. complete all as specified and directed by Engr-in-Charge including testing on completion.
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .