PROVN OF TOILET NEAR FWC, PARKING SHED FOR BEML TATRA, PATH AND UTILITY SHED AT AJNALA ROAD AND SPECIAL REPAIR TO P-43 OF MDC, BLDG NO P-13 AND P-14 OF MED REGT AT AMRITSAR CANTT

Amount

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and raming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface soft/loose soil complete all as specified and directed by the Engineer in Charge.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in any type of soil , complete all as specified and directed by the Engineer in Charge.

Material & Labour for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in foundation, mass concrete etc, complete all as specified and directed by the Engineer in Charge.

Material & Labour for Hard core of broken stone or boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed by the Engineer in Charge.

Material & Labour for 100mm thick cement concrete type B2 (1:3:6) using 40 mm graded aggregate as in sub bases finished even and fair with out using extra cement for laying floor finishes ,complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for machine pressed precast concrete interlocking paver block any shape and size with grey cement and no pigment conforming to IS 15658-2006 of 80mm thickness M-40 Grade. complete all as specified and directed by the Engineer in Charge.

Material & Labour for PCC 1:2:4 type B-0 using 12.5 mm graded stone agg in coping including weathering slightly rounded or chamfered angle and throating & form work complete all as specified and directed by the Engineer in Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/dense soil complete all as specified and directed by the Engineer in Charge.

Removing excavated material or surplus soil/spoil exc 250 m but n.exc 500 m and depositing where complete all as specified and directed by the Engineer in Charge.

Removing excavated material or surplus soil/spoil not exceeding 50metres and depositing where complete all as specified and directed by the Engineer in Charge.

Excavation in trenches in soft/loose soil.not exceeding 10 Square Metre on plan and not exceeding 1.5 meter depth for foundation ,shafts, well, manhole, pier holes etc. getting out and forming bottom surfaces by ramming to required gradient complete all as specified and directed by the Engineer in Charge.

Material & Labour for brick work with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed by the Engineer in Charge.

Material & Labour for brick work (Except Bricks) (Serviceable bricks obtained from dismantling/demolition of brick work shall be reused) , straight or curved on plan exc 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed by the Engineer in Charge.

Material & Labour for preparation of newly plastered or unplastered surfaces of wall and applying two coats of cement base paint over a coat of cement primer complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for mild steel Gde Fe-410-W as in roof trusses, (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee,angle,channel or flat sections) including distance pieces , cleats etc complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for mild steel work as in post and struts including embeding in concrete and screwing etc ,wind tie of roof including securing with bolts complete all as specified and directed by the Engineer in Charge.

Supply & Fixing mild steel flat iron work , MS Plates including drilling holews, notching for screwed, rebating or welding complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for mild Secrew bolt ( Machine made ) with hexagonal or square head at one end and screwed the other , or screwed both ends each secrewed end to be fitted with washer B17and one hexagonal or square nuts. exc 10 but n exc 15 cm long complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength 550 MPA as in roof covering in roof covering including ridge fixed with self tapping screws / L type or J type hook complete all as specified and directed by the Engineer in Charge.

Material & Labour for preparation of new or previously untreated steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enemel paint over a coat of red oxide primer complete all as specified and directed by the Engineer in Charge.

Dismantling existing terrazo dado /flooring or tiles in bath .WC and kitchen etc complete all as specified and directed by the Engineer in Charge.

Dismantling Brick tiles or terracing tiles, single layer on roofs , jointed and pointed in cement mortar complete all as specified & directed by the Engineer-in-Charge.

Demolition of mud in roofs, any thickness including plastering and leaping etc complete all as specified and directed by the Engineer in Charge.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified & directed by the Engineer-in-Charge.

Demolition of cement concrete in ground floor and paving not exceeding 15cm thickness (below or above GL) complete all as specified and directed by the Engineer in Charge.

Disconnecting, dismantling existing water storage tanks and the same , setting aside (or lowering if required) exc 250 litres & n.exc.500 Litres capacity and removal to store complete all as specified and directed by the Engineer in Charge.

Taking down shutter of any description exc. 1 Square Metre but not exc.2Square Metre each and refixing in the same opening after necessary easing ,adjustment etc complete all as specified and directed by the Engineer in Charge.

Taking down chowkhats or frames not exc. 1.50 Square Metre each but with shutter (w/o taking of shutter from the frame ) complete all as specified and directed by the Engineer in Charge.

Taking down chowkhats or frames exc 1.50Square Metre each but n.exc. 4 Square Metre each with shutter (w/o taking of shutter from the frame )complete all as specified and directed by the Engineer in Charge.

Taking down cement plaster on brick or stone walls incl.raking out joints hacking for key scrubbing down with water etc complete all as specified and directed by the Engineer in Charge.

Material & Labour for coloured non skid ceramic tiles 7 to 8 mm thick ( Square/ rectagular ) exceeding 0.06 Square Metre but not exceeding 0.11 Square Metre in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match including 15mm thick screed bed in CM 1:6 complete all as specified and directed by the Engineer in Charge.

Material & Labour for coloured Glazed ceramic tiles 300mm X 200mm X 7mm thick set and jointed in neat cement slurry and pointed in coloured cement to match the floor as on vertical surfaces laid over 10mm thick cement screed in 1:4 complete all as specified and directed by the Engineer in Charge.

Material & Labour for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kilogram/Square Metre including cleaning surfaces etc complete all as specified and directed by the Engineer in Charge.

Material & Labour for 40 mm thick brick tiles laid on cement mortar 1:6, 15mm thick and jointed grouted, flush in cement mortar (1:3) complete all as specified and directed by the Engineer in Charge.

Material & Labour for Brick tiles (Except tiles) laid on cement mortar 1:6, 15mm thick and jointed grouted, flush in cement mortar (1:3) complete all as specified and directed by the Engineer in Charge.

Material & Labour for PCC 1:3:6 type C-2 using 20mm graded stone aggregate as in roof kerb or similar works rounded or chemfered with nececssary form work complete all as specified and directed by the Engineer in Charge.

Material & Labour for APP based polymeric membrane minimum weighing 3Kilogram/Square Metre and minimum 3mm thick reinforced with polyester non woven fabric (wieght not less than 150 gms/Square Metre) laid on primed surface by forced application complete all as specified and directed by the Engineer in Charge.

Material & Labour for brick work with sub class B bricks straight or curved on plan exc 6m mean radius as in half brick walls built in CM 1:4 complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 500 litres capacity rotational moulded polyethylene water storage tanks (cylinderical vertical with closed top) hoisted and fixed in position incl 20mm bore ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed. .(Minimum weight 15mm-142gms/ 20mm-210 gms./25mm-455gms/ 40mm - 690 gms) complete all as specified and directed by the Engineer in Charge.

Material and labour for Box type steel window made of ERW tube P-section of size 60mmX25mm double frame, comprises of glazed Skelton & gauzed shutter of ERW tube P-section size 50mmX20mm with one/two Nos openable leaf consisting of two nos sash bar of T-section 20mmX3mm welded to frame with one No vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/screwed to frame for fixing of glass including fittings and fixtures like Handle, Tower bolts, Stopper, Cleat, Pintal hinges, holdfast etc as given below all as shown on drg No CEJZ/TD 1020/08 Sh 1/3 to 3/3 dt 01 May 2008 complete including cutting holes, making good dismantled portion in PCC 1:2:4 type B-1 complete all as specified and directed by the Engineer in Charge. (a)Hold fast,150mm long of 12mmX3mm MS flat-04Nos per window (b) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (c) MS Tower bolt 150mm long-02 Nos/leaf (d) Z Section stopper 20mmX25mm,100mm long -01 No per leaf (e) Cleat 55mm long of hollow square 15mmX12mm-02 Nos per leaf Note:- 1. Wire guage, Sheet glass, guard bar and painting shall be measured and paid separetely. 2. Mode of measurement for this item shall be for window portion only excluding ventilator portion where ever shown in drawing.

Supply & Fixing for MS box type window/ventilator fixed type with glazing bar without wire work and glass as per Drg No CE JZ-70/06-07 dated 07.06.07 with guard bar including priming coat complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for framed work such as grills ,framed guard bars barred iron doors ;ladders framed balusters railings and similar work conforming to Fe 410-0or Fe 310-0 complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 1.25 mm thick Pressed steel frames of size 125mm x 60mm for single doors including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed by the Engineer in Charge.

Material & Labour for PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate as in filling in pressed steel frames complete all as specified and as directed by Engineer-in-Charge

Material & Labour for 2nd class hard wood 35mm glazed and skelton shutter open rebated and prepared to receive glass,gauge etc.(w/o sash bars)edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc.as specified in Clause 8.20(a) complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 2nd class hard wood 35mm thick plain framed panelled factory made shutter two panels with lock rail and panels of 9mm BWP commercial ply or 12mm veneered complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 25 mm thick Flush shutters for cupboards solid core construction, with block board core, and ply wood face panels, both faces covered with decorative face veneer with lipping to match complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing for Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified and approved complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for factory made solid panel PVC door shutter with MS square tube 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC sheet stirip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top,lock and bottom rail on either side & as gap insert for top rail & bottom rail .panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement Supply & Fixing for in the frame at site as per specification.complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Butt hinges 100mm extruded alumonium alloy with galvanised mild steel hinges pin anodised and fixed type B-21 complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Butt hinges 100mm mild steel medium weight cold rolled complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 150mm Aluminium anodised barrel tower bolt of extruded section complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Aluminium handles cast type anodised of 150mm complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for mild steel barrel tower bolt ,stove enamelled black with bright bolt of 150mm complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for mild steel sliding door bolt plate type stove enameled black with bright bolt not less than 12mm dia with and incl. Alminimum of bolts and nuts four on bolt plate and two on staple plate of 250mm long complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for mild steel pressed handles oval type stove enamelled black of 150mm complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for hasp and staple aluminium anodised including bolt to hinge plate and fixed with screws of 100mm size safety type complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-charge.

Material & Labour for Galvanised wire cloth 0.56mm nominal dia of wire and avg.width of aperture 1.18mm fixed with tinned tacks or galvanised wire staples complete all as specified and directed by the Engineer in Charge.

Material & Labour for sheet glass 3mm thick ordinary quality and glazing with oil putty in square not exc.0.5Square Metre in each pane including hacking out old broken glass (any thickness size quality or desc.) from wooden frames or stone conc. or brick surroundsglazed with putty or fixed with beads exc.105Square Metrecomplete all as specified and directed by the Engineer in Charge.

Material & Labour for Figured glass pin head type 3mm thick and glazing with oil putty in square not exc.0.5Square Metre in each pane including hacking out old broken glass (any thickness size quality or desc.) from wooden frames or stone conc. or brick surroundsglazed with putty or fixed with beads exc.105Square Metrecomplete all as specified and directed by the Engineer in Charge.

Material & Labour for 15mm rendering in cement mortar (1:4) on brick/concrete surfaces finished the surface even and smooth without using extra cement complete all as specified and directed by the Engineer in Charge.

Material & Labour for preparing plastered or unplastered surfaces of ceiling and applying three coat of white wash on ceiling complete all as specified and directed by the Engineer in Charge.

Material & Labour for preparing new decorated plastered or unplastered of walls and applying two coat of dry distemper on walls including cornices pilasters etc complete all as specified and directed by the Engineer in Charge.

Material & Labour for preparing new decorated plastered or unplastered of walls and applying one coat of white wash on ceiling complete all as specified and directed by the Engineer in Charge.

Material & Labour for preparing new decorated plastered or unplastered of walls and applying two coats of dry distemper over a coat of chalk whiting including complete removal of existing treatment of walls complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for applying two coat of cement base paint (Ist quality) in plain pattern on walls and over a coat of alkali resistant priming paint including Complete removal of existing treatment of walls complete all as specified and directed by the Engineer in Charge.

Material & Labour for preparing new surface of wood of any description over 10cm width or girth and applying two coats of synthetic enamel paint , over one coat of pink primer complete all as specified and directed by the Engineer in Charge.

Material & Labour for preparing old painted wooden surfaces and applying one coat of synthetic enamel paint complete all as specified and directed by the Engineer in Charge.

Material & Labour for preparing old painted steel surfaces and applying one coat of synthetic enamel paint complete all as specified and directed by the Engineer in Charge.

Taking up or down steel water tubing 15mm dia and connection ,incl cleaning for refixing complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 15mm bore steel water tubing, 'medium grade' , galvanised , with all fittings ; and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by the Engineer in Charge.

Refixing old steel tubing 15mm incl all fittings fixed to wall or laid in floor complete all as specified and directed by the Engineer in Charge.

Taking up or down steel water tubing 20mm dia and connection ,incl cleaning for refixing complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 20mm bore steel water tubing, 'medium grade' , galvanised , with all fittings ; and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by the Engineer in Charge.

Refixing old steel tubing 20mm incl all fittings fixed to wall or laid in floor.complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Vitreous china wash down water closet white orissa pattern of size 550x440mm including integral foot rest excluding flushing cistern and flush pipe) incl. P or S trap FIXED IN REPAIR complete all as specified and directed by the Engineer in Charge.

Supply and fixing PVC valve less, symphonic action type, flushing cistern, low level white with inlet, ball valve, float and handle including brackets 10litres complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Pvc connection 15mm size with PTMT nuts of length 450mm. complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Vitreous china wash basin, white flat back, size 580x450 excluding traps waste pipe fixed with brackets fixed in repair. complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Waste pipe 32mm for WHB with coupling fixed in repairs. complete all as specified and directed by the Engineer in Charge.

Supply & Fixing in repairs bib taps cast copper alloy chromium plated fancy type 15mm bore with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by the Engineer in Charge.

Supply & Fixing in repairs Angle valves, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down high pressure, screwed both ends for 15 mm bore dia iron pipe or for union, ISI marked, complete all as specified and as directed by Engineer-in-Charge.

Supply & Fixing in repairs Stop valve cast copper alloy with crutch or butter fly handle screwed both ends & screwed for iron pipe of 15mm dia fixed in repair. complete all as specified and directed by the Engineer in Charge.

Supply & Fixing in repairs Stop valve cast copper alloy with crutch or butter fly handle screwed both ends & screwed for iron pipe of 20mm dia fixed in repair. complete all as specified and directed by the Engineer in Charge.

Supply & Fixing in repairs Ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe 20mm complete all as specified and directed by the Engineer in Charge.

Supply & Fixing in repairs PVC floor trap 75mm including CP grating complete all as specified and directed by the Engineer in Charge.

Supply & Fixing in repairs 110mm PVC sanitary connection -for WC connector complete all as specified and directed by the Engineer in Charge.

Dimantling pipes of any desc.fixed to wall or laid under floor complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 110mm bore PVC(SWR) single socketed in any length with rubber ring joint & solvent in any length fixed to walls with dash true nut and bolt at every 2metres length including all fittings complete all as specified and directed by Engineer-in-chargecomplete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 75mm bore PVC(SWR) single socketed in any length with rubber ring joint & solvent in any length fixed to walls with dash true nut and bolt at every 2metres length including all fittings complete all as specified and directed by Engineer-in-chargecomplete all as specified and directed by the Engineer in Charge.

Supply & Fixing in repairs PVC SWR branch piece single equal or unequal 110mm complete all as specified and directed by the Engineer in Charge.

Supply & Fixing in repairs PVC SWR branch piece single equal or unequal 75mm complete all as specified and directed by the Engineer in Charge.

Supply & Fixing in repairs PVC(SWR) bends any radius 110mm with oval access door complete all as specified and directed by the Engineer in Charge.

Supply & Fixing in repairs PVC(SWR) bends any radius 75mm complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for PVC (SWR) vent cowl, 110mm bore complete all as specified and directed by the Engineer in Charge.

Material & labour for 20mm thick granite machine cut slab table rubbed and polished granite as on cooking platform/ Wall partion incl. pointing in white cement 1:2 using marble dust with admixture of pigment to match with marble shade laid over 20mm thick cement screed in cement mortar 1:6. complete all as specified and directed by the Engineer in Charge.

Material & Labour for Reinforced Cement Concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in shelves,bases for water tanks ,roof landing etc complete all as specified and directed by the Engineer in Charge. (including demolition).

Material & Labour for Mild steel bars 6 to 8mm dia cut to length bent to shape required including cranking bending and binding with wire (annealed) not less than 0.9mm or scouring with clips quality conforming to Fe-410 or Fe 410.0 complete all as specified and directed by the Engineer in Charge.

Supply and fixing for solid PVC shutter one side prelam of any shade 18mm thick plain colour as in cup board/ kitchen cabinet shutter etc. complete all as specified and directed by the Engineer in Charge.

Material & Labour for vetrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Square Metre, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor laid over 15mm thick screed in cement mortar 1:6 complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for sinks made of stainless steel 1.00mm thick sheet for kitchen with plug washer wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to Pipe over all size 495x420mm with bowl size 410x330x160mm including 40 mm wasste pipe & coupling complete all as specified and directed by the Engineer in Charge.

Material & Labour for Rendering 5mm thick in CM 1:3 to fair face of brick works or concrete surfaces of ceiling finished the surface for even and smooth without using extra cement.complete all as specified and directed by the Engineer in Charge.

Material & Labour for two coat of oil bound distemper over a coat of primer on newly plastered surface of wall incl preparation of surface complete all as specified and directed by the Engineer in Charge.

Material & Labour for applying two coat of oil bound distemper etc.including Complete removal of existing treatment of old decorated surfaces of wall including stipping nails, holes, filling the cracks with putty complete all as specified and directed by the Engineer in Charge.

Demolition of Reinfoced cement concrete for roofs, floors,(other than ground floors) beams , stair cases, landing,chajjaa and similar suspended work complete all as specified and directed by the Engineer in Charge.

Material & Labour for RCC with type B1 (1:2:4) (using 20mm graded aggregate ) in Slabs supported on walls , beams and columns in floors , roofs , landings, balconies , canopies, deck slabs and cover slab in shelves and the like complete all as specified and directed by the Engineer in Charge.

Material & Labour for form work to the soffits of suspended slabs such as roof slabs , floor slabs , landings and similar work ; not exceeding 200 mm thick (Horizontal or sloping ) and making flat rough finished surfaces of concrete .complete all as specified and directed by the Engineer in Charge.

Material & Labour for TMT bars 6 to 8 mm dia and over, cut to length , bent to shape required , including cranking, bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips .complete all as specified and directed by the Engineer in Charge.

Material & Labour for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushing neat cement slurry with cement @ 3.0 Kilogram/Square Metre complete all as specified and directed by the Engineer in Charge.

Material & Labour for 15mm thick Screed bed or beading layer of cement mortar (1:6) for laying floor finishes complete all as specified and directed by the Engineer in Charge.

Material & Labour for 10mm thick Screed bed or beading layer of cement mortar (1:4) for vertical surfaces like dado, skirting etc. complete all as specified and directed by the Engineer in Charge.

Material & Labour for coloured Non-skid Ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 Square Metre but not exceeding 0.18 Square Metre, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed by the Engineer in Charge.

Material & Labour for coloured Glazed ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 Square Metre but not exceeding 0.18 Square Metre set and jointed in neat cement slurry and pointed in coloured cement to match the floor as on vertical surfaces laid over 10mm thick cement screed in 1:4 complete all as specified and directed by the Engineer in Charge.

Material & Labour for 75 mm thick plain Cement concrete , 1:4:8 type D- 1(40 mm graded aggregate) as in sub base.complete all as specified and directed by the Engineer in Charge.

Material & Labour for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by the Engineer in Charge.

Material & Labour for mild steel framed works, as in door frame, gates of angle or other section with gusset plates, rails, braces etc, drilled for fixing of steel sheeting including drilling or fixing welding be prepared for hanging or sliding with and either hooks and hinges fixing, similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 30 mm thick flush shutter, soild core construction, with block board core and plywood face panel commercial type on both sidescomplete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 35 mm thick 2nd class hardwood glazed and skeleton shutter open rebated and prepared to receive glass/gangue (with sash bars) edges of forming plain chamfered or rounded fitted with cut and mitred bead for securing glass/ gauged etc size of member of shutter as per Pt-I, Section 8, Clause 8.20 (a) complete all as specified and directed by the Engineer in Charge.

Taking down steel window / ventilator of any description & size n exc 1.50 Square Metre area complete all as specified and directed by the Engineer in Charge..

Supply & Fixing for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aparture 1.40mm and fixed with stainless steel wire staples in window and door as in new door/window.complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 3mm thick sheet glass in repairs , ordinary quality and glazing with oil putty in square n.exc 0.5 Square Metre in each pane including hacking out old broken glass (any thickness, size , quality or description) from wooden frames glazed with putty or fixed with beads .complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 200mm aluminum , anodised, barrel tower bolts of extruded section complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 250mm aluminum alloy, anodised , sliding door bolt with hasp and staple ( bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy and fixed.complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 2nd class hardwood small fittings such as brackets of any type, latch and hinge blocks, shapes door and window stops and the like including all necessary labours ; articles n exc 200 Cucm each complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for flat iron as in hold fast,including tarring or coal tar black paint conforming to Fe 410-0 or Fe 310-0. complete all as specified and directed by the Engineer in Charge.

Material & Labour for PCC (1:2:4 ) type B1( using 20 mm graded aggregate ) as in blocks for fixing of holdfast complete all as specified and directed by the Engineer in Charge.

Material & Labour for 50mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in path or similar works surfaces finished even and fair without using extra cement complete all as specified and directed by the Engineer in Charge.

Supply and fixing for 25mm dia MS pipe PVC sheathed, decorative fancy type, curtain rod including brackets & a set of ABS finials complete all as specified and directed by the Engineer in Charge.

Dismantling of 100/75 mm bore cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of floor/trenches, if required complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 110 mm bore PVC (SWR ) pipes single socketed, in any lenth with rubber ring fixed to wall complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for PVC (SWR) bend 110 mm size complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 110 mm bore PVC (SWR) single Tee complete all as specified and directed by the Engineer in Charge.

Material and labour for cup board shutter, frame made of angle iron 35x35x6mm, covered with 1.00mm thick MS sheet, welded to frame including suitable handle, lugs and locking arrangement complete all as specified and directed by the Engineer in Charge.

Supply and fixing for PVC sheet 5mm thick, in backside of kitchen cabinets for support complete all as specified and directed by the Engineer in Charge.

Supply and fixing for PVC board 18mm thick, in cupboard shelves and backside (for hanging) kitchen cabinet etccomplete all as specified and directed by the Engineer in Charge.

Supply & Fixing for solid PVC board 18mm thick with one side prelam of any shade plain colour as in cup board shutters , kitchen cabinet shutter etc & similar works complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 40mm long box type steel hinges spring action type complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 75-80mm long stainless steel handle complete all as specified and directed by the Engineer in Charge.

Material & Labour for for PCC (1:3:6) type C-0 (using 12.5mm graded stone aggregate) averaging 50 mm thick as in roof padding mixed with & including WPC @ 100ml per 50 Kilogram cement finishing the surface even and smooth without using extra cement complete all as specified and directed . complete all as specified and directed by the Engineer in Charge.

Material & Labour for 15mm thick plaster in CM (1:3) on RCC roof surfaces as in vertical surfaces mixed with water proofing liquid compound finished the surface even and smooth without using extra cement complete all as specified & directed. (Note : WPC shall be mixed @ 100 ml / 50 Kilogram bag of cement or as recommended by manufacturer and the same shall be measured and paid seperately.complete all as specified and directed by the Engineer in Charge.

Material & Labour for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girt complete all as specified and directed by the Engineer in Charge.

Material & Labour for removing of nails, making good holes, cracks, etc and applying 2 mm thick wall care puty on walls including finished the surface even and smoothcomplete all as specified and directed by the Engineer in Charge.

Material & Labour for for 75 mm thick plain Cement concrete , 1:4:8 type D-1 (40 mm graded aggregate) as in sub base. complete all as specified and directed by the Engineer in Charge.

Material & Labour for cement concrete type D2, 1:4:8 using 40mm graded agregate as in foundations, filling and mass concrete complete all as specified and directed by the Engineer in Charge.

Material & Labour for Reinforced Cement concrete type B-1 1:2:4 using 20mm graded aggregate (Nominal mix) as in slabs supported on walls, beams and columns , in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by the Engineer in Charge.

Material & Labour for Reinforced Cement Concrete type B1, 1:2:4(20 mm graded aggregate) as in Beams, canatilivers, bressummers, lintels over 1.5m span etc complete all as specified and directed by the Engineer in Charge.

Material & Labour for flat formwork to sides and soffits of floor or roof beams, beam haunchings, girders,bresumers, lntels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams etc.for rough finished surfaces of concrete surface complete all as specified and directed by the Engineer in Charge.

Material & Labour for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90 mm dia. Or securing with clips complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for powder coated anodised aluminium ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 Kilogram/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc(Thickness or powder coating not less than 50 micron) complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for powder coated aluminium frame for doors ,windows, ventilators with one or more rebates including joining cleats for fixing (minimum thickness of powder coating 50 micron) complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for, Tinted Sheet glass, 5.5mm thick ordinary quality, in squares,exceeding 0.50 Square Metre in each pane including rubber packing and aluminium beading as per instructions of manufacturer complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Rolled mild steel in framed work (Fe 410W Gde-E-250, Quality A) as in doors or gates of angle or other section with gusset plates, rails, braces,etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of framemade out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed by the Engineer in Charge.

Material & Labour for Galvanised mild steel wire cloth, 0.63 mm nominal dia. of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 200mm aluminium alloy anodised, sliding door bolt with hasp, staple ( bolt type) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy , complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for non skid ceramic light coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Square Metre but not exceeding 0.18 Square Metre in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles over and including 15mm thick screed bed in CM 1:6 & complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for glazed ceramic coloured tiles 450mmm x 350mm x 7mm thick, etc. on vertical surfaces such as skirting , dados and risers to steps etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match over and including 10mm thick rendering plaster in CM 1:4 on brick surface complete all as specified and directed by the Engineer in Charge.

Material & Labour for Cement concrete 50 mm thick type C-2 (1:3:6) using 40 mm graded stone aggregate as in plinth protection etc finished even and smooth using extra cement complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for PVC (SWR) floor trap (Dia of outlet pipe 75mm), plain with grating including jointing with cement complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for (SWR) pipes of 75mm dia single socketed, in any length with rubber ring joints, laid in trnches or in floors complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Vitreous china wash down water closet pan( pedestal pattern), white with PVC(SWR) 'P' trap 110/110mm bore complete all as specified and directed by the Engineer in Charge.Note:-Rate of supply for Flushing cistern, flush pipe, seat cover etc have been taken separately, complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Plastic water closet seat, back, closed pattern with flat bottom , and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Chromium plated Health faucet with 1.5 metre long chain complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for vitreous China wash basin pedetal pattern white, flat back size550x400mm of pedestal type including CP waste coupling 32mm bore, fancy type CP brass Pillar Tap 15mm bore complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 15mm bore/pillar cock CP Stop valves, cast copper alloy, screwed down , high pressure, with crutch or butterfly handles , screwed both ends for iron pipe or for unions complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Chromium plated Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Soap dish, any type, fixed to plugs with chromium plated brass screws , complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for PVC waste pipe for urinals/WHB of 32mm dia , complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for grating doom 100mm dia of PTMT.(minimum weight 25gms), complete all as specified and directed by the Engineer in Charge.

Material & Labour for Reinforced Cement Concrete M-25 (Design Mix) Type B-1 1:2:4 (Using 20mm graded aggregate) as in column, footings, plinth beams complete all as specified and directed by the Engineer in Charge.

Material & Labour for Reinforced Cement Concrete M 25 (Design Mix) Type B-1 1:2:4 (Using 20mm graded aggregate) as in columns complete all as specified and directed by the Engineer in Charge.

Material & Labour for Reinforced Cement Concrete M 25 (Design Mix) Type B-1 1:2:4 (Using 20mm graded aggregate) as in beams complete all as specified and directed by the Engineer in Charge.

Material & Labour for Reinforced Cement Concrete M 25 (Design Mix) Type B-1 1:2:4 (Using 20mm graded aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by the Engineer in Charge.

Material & Labour for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by the Engineer in Charge.

Material & Labour for Formwork to sides of fair finished flat surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed by the Engineer in Charge.

Material & Labour for Formwork to sides of fair finished flat surfaces of square, rectangular or polygonal Form work to sides of pillars, posts, struts, columns and stanchions complete all as specified and directed by the Engineer in Charge.

Material & Labour for brick work with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar 1:4 complete all as specified and directed by the Engineer in Charge.

Supply only integral water proofing compound complete all as specified and directed by the Engineer in Charge.

Material & Labour for applying two coats of whitewash on ceiling including preperation of newly plastered surfaces complete all as specified and directed.

Material & Labour for 100mm thick Cement concrete type C-2 , 1:3:6 (using 40 mm graded aggregate) as in sub base or similar works complete all as specified and directed.

Material & Labour for coloured non skid ceramic tiles 400 x 400 x 7mm thick in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match including 15mm thick screed bed in CM 1:6 complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for centre hole mixer cast coppre alloy chromium plated with capston head (Pillar Mounted) srewed down high pressure with lettered hot or cold with long screwed shanks fly nut screwed for iron pipe 15mm dia complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and directed by the Engineer in Charge.

Supply & Fixing vitreous china urinal half stall type white with grating and union for discharge pipe, including providing and fixing plug, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement fixing with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Vitrous china urinal partition white of size 310x770mm of approved make and fixed to wall terminating about 40cm above floor line complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for rotational moulded polythene, triple layers, water storage tank 1000 Litres capacity, closed top, cylindrical, hoisted and fixed in position including Supply & Fixing for 20mm bore PTMT ball valve epoxy coated minium weight 210gms with aluminium rod complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Galvanised iron steel water tubing (Medium grade), 25mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 25 mm bore, Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for soap dish, vitrous china white, approximate size 160 x 160 x 90 mm embedded in the wall complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Vitrous china white (Box type) toilet paper holder fixed to walls with chromium plated (CP) brass screws complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for of brass cromium brass plated fancy type bib taps 15mm bore long nose screwed down screwed for iron pipe or for brass complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 125mm CP shower rose fancy type with CP arm complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 100mm dia CP grating with or without hinge type or hole type complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for CP brass towel rail 600mm long complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for 50mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc complete all as specified and directed by the Engineer in Charge.

Material & Labour for for Chequred cement concrete tiles 30cm x 30cm x 25mm thick set and jointed and pointed in neat cement slurry in floors with grey cement and no pigment over screed bed 15 mm thick in CM 1:6 complete all as specified and directed by the Engineer in Charge.

Material & Labour for for 25mm sand filling under/over floors or in foundations including watering and consolidation complete all as specified and directed by the Engineer in Charge.

Material & Labour for for Machine pressed pre-cast concrete interlocking paver block any shape and size conforming to IS 15658-2006 of 60mm thickness M-35 grade with grey cement and pigment complete all as specified and directed by the Engineer in Charge.

Material & Labour for PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 100 mm dia SWG pipe complete all as specified and directed by the Engineer in Charge.

Cutting into existing manhole for connecting new drain pipe of 150 mm bore and making good the pipe and rendering disturbed surface where drain pipe have been inserted cutting out existing benching for forming branch channel (1/2 round or 3/4 round as required) in cement concrete 1:2:4 type B1 and finished the surface even and smooth and reforming benching as required complete all as specified and directed by the Engineer in Charge.

Taking down carefully the existing aluminium point wiring of any size and capacity and type by disconnecting from the either terminals complete including fittings and fixtures such as switches, sockets,ceiling rose, regulators and light fittings any type etc by unscrewing and taken away from site complete. Note :cost of unserviceable materials will be charged from the contractor against schedule of credit.

Material & Labour for wiring complete with 1.5 sqmm single core PVC insulated unsheathed cable 1100 volts grade, multistranded with copper conductors conforming to IS specifications, drawn through and including conceled conduit concealed/ fixed on wall / ceiling with suitable clamps, screws, etc or concealed in wall including terminal boxes fabricated with 1.6 mm MS sheet concealed in walls covered with plastic laminated sheet top cover 3mm thick fixed with cadmium plated iron screws for housing the switches, switch sockets outlets, fan regulators, etc, including provn of 1.5 sqmm PVC insulated unsheathed cable with multistranded copper conductor as earth continuity conductor and connecting to common earth dolly for One light point/Bell/Fan point controlled by one switch complete all as specified and directed by the Engineer in Charge.

All as per serial item No 204 but for one 3 pin 5 amps switch socket on independent board complete all as specified and directed by the Engineer in Charge.

All as per serial item No 204 but for one 3 pin 5 amps switch socket on same board complete all as specified and directed by the Engineer in Charge.

All as per item No. 204 herein before but with cable 2.5 sqmm (nominal area) multistranded copper wire unsheathed for one 3 pin socket outlet 15 amps on independent board including continous earth wirte PVC insulated 2.5 sqmm copper multistranded conductor connecting to common earth and earth dolly complete all as specified and directed by the Engineer in Charge. Note for item No 204 to 207 :- The wiring shall be done in proper colour coding using red,yellow and blue for phase,black for neutral and green for earth leads.

Supply and fix switch piano one way 5 A, SP, 230 Volts complete all as specified and directed by the Engineer in Charge.

Supply and fix Socket outlet 2 in 1, 3 pin 5 Amps Flush type complete all as specified and directed by the Engineer in Charge.

Supply and fix Switch outlet 2 in 1, 3 pin15 Amps Flush type complete all as specified and directed by the Engineer in Charge.

Supply and fixing ceiling rose surface bakelite 3 terminals 65x32mm complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant/batten fittings complete all as specified and directed by Engineer-in-Charge

Supply and fix wall/ceing mounting LED 18 Watt PC Diffuser tube light fitting complet with all aceesories 1x18W LED suitable for domestic application 240Volts 50HZ including one tube rode and internally pre-wired with 1.5 sqmm twin twisted flexible copper conductor complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for in repair MCB double pole, 240 volts, 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for in repairs MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type complete all as specified and directed by the Engineer in Charge.

Supply and fixing of socket outlet two-in-one, 3 pin each suitable for 5 and 15 Amperes flush type, 250 volts AC complete all as specified and directed.

Material & Labour for LT cable of 1100 volt XLPE insulated and PVC sheathed of size 10 sqmm 2 core with cable gland including taking down old unserviceble cable complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Sand cushioning to UG cable 40cm wide 15cm and 10cm thick above and below the cable in trenches/ducts complete all as specified and directed by Engineer-in-Charge.

Supply and laying burnt brick sub class 'B' modular size, for cable protection laid length wise perpendicular to the axis of cable complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as specified. Make :Legrand Lexic / Hager /Schneider Elect . (Note : cost of removing old wooden box and making good of surface as original by brick work, plastering, whitewash/colour/distemper etc is included in quated rate) complete all as specified and directed by the Engineer in Charge.

Material & Labour for earthing complete with galvanised earth plate electrode 600 X 600 X 6 mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.5 m below normal ground level, connected to galvanised earth lead wire 4 mm dia by means of nuts, bolts, check nuts & washers of galvanised iron or steel all as shown on electrical plate No. 3 of MES schedule 2009, Part – I (Specifications) and connected to main switch board / main DB’s / earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1, duly reinforced with 6 mm dia mild steel round bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:3:6 type C-1, GI protection pipe light grade 15 mm bore up to 7.5 m length from earth electrode & engraving of earth marking on nearby building with CM 1:4 plate size 200 X 150 X 15 mm & painting of earth result etc. including testing on complete all as specified and directed.

Material & Labour for sub main wiring with 1100 volt grade two single core PVC insulated and unsheathed cable with stranded copper conductor 4 sqmm drawn into and including electrical grade PVC conduit not less than 25 mm dia with IS 9537 (Part-III) 1983 mark, or relevant ISI mark with all accessories fixed concealed including chase cutting in brick/ stone masonry for fixing conduit and making good the disturb surfaces of wall as per existing including 2.5 sqmm multi - stranded copper conductor as earth wire in green colour complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for exhaust t fan 250 mm sweep metal body heavy duty including cutting of wall /window/lowers and fixing arrangement complete all as specified and directed by the Engineer in Charge.

Supply and fixing LED bulb 9 Wat, 230 Volt complete all as specified and directed by the Engineer in Charge.

Supply and fixing distribution board double door made out of CRCA mild steel sheet surface with insulated material like polyster or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 4 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and directed by the Engineer in Charge.

Supply and fixing in replacement of bldg security light fitting LED 25 Watt all accessories complete mounted on, nuts with twin washers grouted in wall including connection with 2 core PVC insulated overall sheathed flexible cable with multistranded copper conductor of size not less than 1.0 sq mm from ceiling rose to fitting terminal complete all as specified and directed by the Engineer in Charge.

Material & Labour LT cable of 1100 volt XLPE insulated and PVC sheathed of size 6 sqmm 2 core with cable gland including taking down old unserviceble cable complete all as specified and directed by Engineer-in-Charge.

Material and labour for brick protection to cable using old size sub class 'B' bricks, laidflat, dry butt jointed, laid lengthwise perpendiclar to the axis of cable complete all as specified and directed by the Engineer in Charge.

Material & Labour for Sand cushioning with layer of sand 8cm thick before laying of cable and 15 cm after lying of cable in trenches complete all as specified and directed by the Engineer-in-Charge.

Supply and fixing / laying galvanised pipe 50 mm bore medium grade fixed to pole with clamps nuts, bolts and washers or laid under road crossing or fixed to wall complete all as specified and directed.

Supply and fixing of PPR gate valve (brass insert) of size 20mm complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Socket 16 Amp multipurpose shutter type fixed on laminated sheet top cover complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for Switch 16 Amp with indicator fixed on laminated sheet top cover complete all as specified and directed by the Engineer in Charge.

Supply and Fixing indicator lamp red colour 6 amp complete all as specified and directed by the Engineer in Charge.

Supply & Fixing for lamp holder insulated body angular type with back plate of 3 mm thick bakelite, laminated hylem sheet of appropriate size & MS box of suitable size and making good surface as original by plastering and whitewash/colour/distemper etc complete all as specified and directed by the Engineer in Charge.

Supply and fixing for fluorescent tube light fitting suitable for 1 x 40/36 Watt complete for wall mounting and making all electric connections including tube rod one nos complete all as specified and directed by the Engineer in Charge.

Supply and fixing for Blanking plate of plastic (suitable for distribution board) complete all as specified and directed by the Engineer in Charge.

Supply and fixing for LED light fitting energy saving new generation 10 Watt LED IP65 bulkhead luminaire with opal diffuser complete with all accessories complete all as specified and directed by the Engineer in Charge.

Supply and fixing for CFL light compact luminaires with decorative end caps and electronic ballast including CFL 36 watt and making all electric connections complete all as specified and directed by the Engineer in Charge.

Supply and fixing for RCOB for earth leakage, overload, short circuit protection double pole 40 amp with isolator and 100mA sensitivity including all electrical connection complete all as specified and directed by the Engineer in Charge.

Supply and fixing for sheet metal enclosure for DB’s (Double door type) when MCB’s to be used, single pole and neutral, 8 ways with 200 ampere rated bus bar, 240 volts fixed sunk / flush to the wall or niche complete all as specified and directed by the Engineer in Charge.

Supply and fixing for ceiling fan of sweep 1200 mm complete with accessories, and suitable for operation on 230 Volts single phase 50 Hz AC supply and connectin up with and including two core PVC insulated, PVC sheathed copper conductor flexible cable 24/ 0.2 mm including fixing and making connection complete all as specified and directed by the Engineer in Charge.

Supply and fix in replacement of security light fitting LED 25 Watt with & Including GI bracket of suitable size made of 40mm dia light grade bracket upto 1.0 mtr long bent to shape, mounted on wall with two nos 8 mm dia, 40 mm long bolts, nuts with twin washers grouted in wall , including connection with 3 core PVC insulated overall sheathed flexible cable with muyltistranded copper conductor of size not less than 1.0 sq mm from celing rose to fitting terminal including taking down old CFL security light fitting complete all as specified and directed by the Engineer in Charge.

Supply and fixing for GI bracket light grade GI Pipe 1.2 mtr Length for fixing of street light fitting 36/40 Watt including connection complete all as specified and directed by the Engineer in Charge.

ESS KAY BUILDER

amardeep traders

RAJ KAMAL BUILDERS

MAAN ENTERPRISES