CA NO GE/AFJ-52/2022-23 REPAIR /REPLACEMENT OF LT UG CABLE,STREET LIGHT,OVER HEAD LINE PANEL BOARD FEEDER PILLARS JUNCTION BOXES,WATER SUPPLY AND ALLIED WORKS AT SHASHITAR AND SALYARCHATTA UNDER GE (AF) JAMMU

Amount

Supply , laying , testing & Commissioning UG cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (Heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm, 4 core, some cable shell be laid at new place with Suitable thimbles complete all as specified and directed by Engr-in-Charge.

Description all as per item No-01 but size 16 sq mm, 4 core complete all as specified and directed by Engr-in-Charge.

Description all as per item No-01 but size 50 sq mm, 3.5 core complete all as specified and directed by Engr-in-Charge.

Description all as per item No-01 but size 95 sq mm, 3.5 core complete all as specified and directed by Engr-in-Charge.

Taking out of old serviceable / unserviceable PVC under ground LT cable of any size and type fixed on pole, wall or laid in floors, trenches, across road crossing etc ,including taking out of cable covers of precast PCC / RCC slab or brick cover etc setting aside serviceable materials in safe custody for reuse and or unserviceable materials consider as schedule of credit complete all as specified and as directed. Note:- i). Dismantling of clamps nuts bolts etc, taking out of GI pipe in cable protection shall be measured and paid seperately under respective item of this schedule. ii).Cost for making good the disturbed surfaces of floors / walls in cement mortar 1:3 shall deemed to be included in the unit rate quoated . However cost for making good the disturbed surfaces of roads with PCC and hard core filling is out of scope of this work and shall be measured and paid separetely under respective item 20 of this schedule.

Re-Laying only of serviceable LT UG cable of any size and type in trenches, floors, across road crossing, or fixed on poles, walls, or passing through pipe, cable obtained from item No. 09 here-in-before complete all as specified and as directed. Note:- i). Handling of UG cable to working site as ordered shall be carried out by the firm and rate for the same shall deem to be included in the unit rate .

Re-Laying only of serviceable brick / PCC slab cover obtained from item No 10 here-in-before for cable protection cover laid width wise along length of cable complete all as specified and as directed.

Dismantling Steel or concrete poles/struts any size and shifting the another place PCC and exacavation shall be paid separatly.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth and getting out in any type of soil for laying of LT UG cables complete all as specified and as directed by Engr in charge. Note:- The Rate quoted deemed to including cutting and removal of PSP Sheets wherever occured during excavation and the same shall be staged at desired location as directed at site

Returning, filling in, including spreading levelling, watering and well ramming in layers not exceeding 25 cm thick in hard dense soil complete all as specified and as directed by Engr in charge.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed by Engr in charge.

Supply and fixing element with rubber washer (O ring) cap 1.5 to 2 KW tringler/round type complete all as specified and as directed by Engr in charge.

Supply and fixing thermostat 30- 70 degree 230 volt complete all as specified and as directed by Engr in charge.

M&L Plain cement concrete 1:4:8 type D2 using 40mm graded stone aggregate for foundation of poles complete all as specified and as directed.

M & L PCC 1:3:6 type C1 using 20 mm graded stone aggregate for coping of poles/road/plinth blocks of LT poles etc incl fair finishing the exposed surfaces even and smooth without using extra cement including necessary form work complete all as specified & directed.

Supply and laying of DWC (Double Wall Corrugated) HDPE Pipe, ISI Marked IS 16205 Part-II, of outer dia of 77 mm and inner dia 63 mm with smooth internal and profiled external surface for non pressure under ground cable including all connected accessories like coupler, 'O' Ring etc, for protection of cable complete all as specified and as directed

M & L for Cutting through existing road surfaces i.e. surfacing PCC soling etc, and making trench of minimum 500mm wide 100cm in depth along the cross section of road for laying of pipes or UG cables, including returning filing in, well ramming & removal of surplus spoil to a distance not exc. 50 m & repairs to road surfaces to match with existing specification after laying the pipes/cable etc. all as specified & directed.

Cross arms, bracings, supports,clamps and back plates fabricated from structural steel sections including nuts, bolts, washers,welding, bending cold or hot,drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint all as specified.

Steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts & screws as specified type 410 SP-31 (9.0 metres long) and duly painted with two coats anticorrosive paint internally and externally upto planting depth,alternate black and yellow straps of synthetic enamel paint 30cm each upto 1.5mtr from ground level and remaining pole painted with aluminium paint including writing Nos complete to entire satisfaction of Engr-in-Charge all as specified and directed .

Supply and Fixing GI tubing medium grade 40mm dia using water supply including provisioning of suitable fittting mild steel flat iron clamps and bolts, nuts and double washers etc for holding of GI pipe alongwith poles including taking out old broken GI pipes, complete all as specified and as directed by Engr-in-Charge.

Supply and Fixing GI tubing light grade 50mm dia along the wall/in trenches/in duct/in culvert/road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holding of GI pipe alongwith poles including taking out old broken GI pipes, complete all as specified and as directed by Engr-in-Charge.

Supply and fixing aluminium thimbles in replacement suitable for under ground LT cables of following sizes including cutting of exsting burn/dammaged cable after disconnecting from exsting position ,extending the cable from cable loop including neccesory earth work and reconnecting the same of size of 16 Sqmm complete all as specified and as directed by Engr-in-Charge.

All as per Item No. 22 but size 25 Sqmm complete all as specified and as directed by Engr-in-Charge.

All as per Item No. 22 but size 70 Sqmm complete all as specified and as directed by Engr-in-Charge.

All as per Item No. 22 but size 95 Sqmm complete all as specified and as directed by Engr-in-Charge.

Supply & Fixing PVC insulated sheathed service wire twin core 6 Sqmm aluminium solid conductor 1100 volts grade incl taking down old unserviceable one.

Supply & fixing PVC insulated sheathed service wire twin core 10 Sqmm aluminium solid conductor 1100 volts grade incl taking down old unserviceable one.

Supply and fixing change over switchs off-load 200 amps 4 pole sheet metal encloser complete all as specified and directed.

Supply and fixing change over switchs off load 100 amps 4 pole sheet metal encloser complete all as specified and directed.

Supply and fixing MCCB 400 amps 4 pole 36 KA with adjustable thermal and fixed magnetic setting, fixed in repairs complete all as specified and directed.

Supply and fixing MCCB 200 amps 4 pole 25 KA with sheet metal encloser with adjustable thermal and fixed magnetic setting, fixed in repairs complete all as specified and directed.

Supply and fixing MCCB 160 amps 4 pole 25 KA adjustable thermal and fixed magnetic setting, complete all as specified and directed.

Supply and fixing MCB TPN 63 amps four pole C curve 25 KA complete all as specified and directed.

Supply and fixing MCB single pole neutral 16 amp to 32 amps C Curve 25 KA with sheet metal encloser, complete all as specified and directed.

Supply and fixing MCB single pole 06 amp to 32 amps C curve 25 KA with sheet metal encloser, complete all as specified and directed.

Preparation of old painted surface of 9 m steel tubular poles above the top of PCC coping. Painting of pole from top of coping to a height of 1.5m (bottom portion of pole) with two coats of synthetic enamel paint in black and yellow alternate strip and painting the rest portion of pole of (approx length 7 m)including painting of cross arms/clamps etc complete with two coats of synthetic enamel aluminium paint and to the entire satisfaction of Engineer-in-Charge complete all as specified and directed

M & L for preparation of old cement based painted surfaces of RCC pole 9 m by cleaning of deposited materials, and painting with one coat of exterior emulsion weather coat paint of approved make and colour complete all as specified and directed by Engineer-in-Charge

S & fix LT cable joining kit straight through heat shrinkabale complete with jointing materials suitable for LT armoured cable 4 core of size 10 to 50 Sqmm all as directed

S & fix LT cable joining kit straight through heat shrinkabale complete with jointing materials suitable for LT armoured cable 4 core of size 70 to 120 Sqmm all as directed

S & fix LT cable joining kit straight through heat shrinkabale complete with jointing materials suitable for LT armoured cable 4 core of size 150 to 240 Sqmm all as directed .

S & fix LT cable end joining kit heat shrinkabale complete with jointing materials suitable for LT armoured cable 4 core of size 70 to 120 Sqmm all as directed .

S & fix LT cable end joining kit heat shrinkabale complete with jointing materials suitable for LT armoured cable 4 core of size 150 to 240 Sqmm all as directed .

Supply, installation , commissioning and testing LT feeder pillar box in replacement of suitable size,outdoor cubical type floor mounted factory made of CPRI approved factory, totally enclosed vermin proof with front and rear opening with IP-54 protection as per IS - 8623 duly powder coated , fabricated out of 2.0 mm thick mild steel sheet mounted on frame of mild steel angle iron 60 cm x 60 cm x 6mm and , 45 cm above ground level duly supported with mild steel angle iron struts 60 cm x 60 cm x 6mm thick and embedded in PCC foundation in PCC 1:2:4, type B-1 , using 20 mm graded crushed stone aggregate , with suitable 415 Volt, 3 phase, four wire copper bus bar of rating capacity 400 Amps duly drilled holes for connections, R-Y-B-N insulated with different colour code and sleeved mounted on insulators complete prewired and cable connection with copper conductor wire upto Aluminium bus bars including all incoming and outgoing cable connections with suitable size of copper lugs/ gland including supply and fixing of MCCB four pole, 415V,I/C- 200 Amp. 25KA-01No Outgoing 63 Amp 4 pole- 05 Nos. including taking out old unserviceable, complete all as specified and directed by Engr - in- Charge.

Supply , installation , commissiong & testing of LT feeder pillar compartmentalised design of size not less than 70 x 70 x 25 cm suitable for 440 volt 3 phase 4 wire system made out of 2.0 mm CRCA sheet powder coated having gasketed front two hinged doors with locking arrangement including bottom and top detachable gland plate complete with suitable size of rust proof nuts, bolts, and washers etc.. complete with mounting accessories including the following components :- (a) Four 30cms long aluminium bus bar 200 Amp mounted on epoxy insulators provided with rust proof nuts bolts and washers (b) Incoming MCCB-125 Amp LED indicating lamps - 3 nos. (Red ,Yellow, Blue)

Servicing of diesel engine generating set capacity 125 KVA repair/replacement of the following defective parts through authorised service engineer/mechanic . (Note : Service of DG Sets 40 KVA to 63 KVA - 4 Nos. All spare required for replacement shall be supplied under following items).

Taking down old fuel filter by unscrewing nuts and bolts and fixing new one with same size and specification of old filter -Mico

Taking down old engine oil filter by unscrewing nuts and bolts and fixing new engine oil filter with same size and specification of old filter.

Taking down old air filter by unscrewing nuts and bolts and fixing new one with same size and specification of air filter with connecting accessories .

Water seperator filter

Draining out old engine oil and refilling by multigrade engine oil 15W-40 (Servo)

Battery terminal

Fuel pipe

Hose pipe

Self starter repair

Alternator wiring work and repair

Oil seal and timing set

Control KVAR 3U2 Part No KVAR3U200000

Radiator cleaning with acid and fins repair

Complete service charge

Coolant

Battery leads

Servicing of DG set capacity 15 to 30 KVA installed at 23 Wing AF including carrying out maintenance and check alongwith following repairs (a)Drain out the lubricating oil from sump and refilling after proper cleaning (b)Replace engine oil filter cartridge . (c)Renew fuel filter cartridge (d)Check tightness of all nuts and bolts (e)Check adjustment of V belt for driving engine water pump and alternator. (f)Assembling complete old serviceable parts and replacement of old unserviceable parts by new one as per direction of Engr-in-Charge. (g)Testing of DG set after servicing as per Engr –in Charge. (h)Cleaning of air cleaner filter after period of hrs run as specified by manufactures in manual Note:- (i) Any minor parts such as screws, washers , split pin , circlip etc shall be supplied by the firm, rate for the same shall be deemed to be included in the unit rate quoted. (ii) The Job shall be carried out after two hundred hrs run /as when required directed by engr-in-charge of DG Set and shall be measured and paid separatly,no of times carried out during entire period of contract (iii) during servicing of engine oil shall be Issued by Deparment

Supply & Fixing oil pipe of DG Set 15 to 30 KVA, incl taking down old unserviceable one complete all as specified and directed by Engineer-in-Charge.Make: Kirloskar/Cummins/Crompton Greaves.

Supply & Fixing lub oil filter of DG Set 15 to 30 KVA incl taking down old unserviceable one complete all as specified and directed by Engineer-in-Charge. Make: Kirloskar/Cummins/Crompton Greaves.

Supply & Fixing air filter of DG Set 15 to 30 KVA, incl taking down old unserviceable one complete all as specified and directed by Engineer-in-Charge. Make: Kirloskar/Cummins/Crompton Greaves.

Supply & Fixing fuel diesel filter of DG Set 15 to 30 KVA, incl taking down old unserviceable one complete all as specified and directed by Engineer-in-Charge. Make: Kirloskar/Cummins/Crompton Greaves.

Dismantling and taking down the existing defective street light/security light fitting of any type and any capacity fixed at any height by replacing UNSV part including perpex cover checking loose connection etc, restroration of electric supply, detecting and repair of UG cable fault whenever required round the clock all as directed at site on daily complaint basis. Note :- Due to security point One Electrician (Skilled) and One Helper shall be always present in the station. One complaint shall be considered as one Job.

Supply & fixing of Powder coated pressure die cast alluminium compact high power LED street light fittings with heat resistant toughned glass with lense and top opening having 45 Watt including making electric connections using two run of 1.5 sqmm single core unarmoured wire from junction box, fixed in repairs,CA No also engaved on street light complete all as specified and as directed by Engr-in-Charge. Note :(i) A certificate from the manufactures for warranty minimum upto 02 years shall be obtained and submitted to the AGE/GE (i) Any touch up of the existing surface due to changing of fittings shall be done by contractor with similar surface finish without extra cost to the department. Make: Cat no. LSTS-45-CDL-M of Crompton or eql in Phillips/Wipro

Material and labour for repair to existing LED street light fitting 45 Watt to 60 Watt of any make including supply and replacement of driver, LED Strips and other minor allied items required at site to make the light fitting serviceable complete all as specified and directed by Engineer-in-Charge.

Material and labour for repair to existing LED street light fitting 90 Watt to 100 Watt of any make including supply and replacement of driver, LED Strips and other minor allied items required at site to make the light fitting serviceable complete all as specified and directed by Engineer-in-Charge.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6.0mm thick buried directly in ground, (Earth pit not less than 2.25 mtr deep below ground level) with top edge of plate not less than 1.5 mtr below normal ground level, connected to and including 4 mm dia galvanised earth lead wire by means of bolts, nuts, check nuts and washers of galvanised standard iron or steel all as specified or indicated in electrical plate no 3 of MES Part-I, including testing on completion including the material and labour of the following :- (a) Excavation and earth work for drilling hole for electrode in any type of soil. (b) PCC pit in cement concrete 1:2:4 type B-1 .c) Precast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than 1.87 Kg/Sqm. (d) Funnel with watering pipe of GI 20 mm nominal bore medium grade and copper lugs etc all as specified. (e) 15 mm nominal bore light grade GI protection pipe 5 mtr long for protection of earthing lead from mechanical injury or tempering. (f) Requisite quantity of common salt and charcoal. (g) Testing of earthing. Note : (a) On testing after completion of earthing, if the desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk and cost to the entire satisfaction of the Engineer-in-Charge. (b) The contractor shall quote his rate considering taking down cost of existing unserviceable earthing.

Repair/replacement of industrial RO CPVC pipe 15mm complete with accessories

Supply and fixing PVC clamps for CPVC including aasy

Servicing of indusrial RO at Shashithar and Salyarchatta 23 Wing AF including carrying out maintenance and check alongwith following repairs (a)Drain out the pipe and Replace new pipe and fixing the same.(c)Cartridge (d)Check tightness of all fitting Note:- Any minor/major parts such as screws,fillet,membrane, washers,PVC fitting etc shall be supplied by the firm, rate for the same shall be deemed to be excluded in the unit rate quoted.

Supply memrane for industrial RO

Taking out burnt winding with allied insulation materials of servo stabilizer including M&L for rewinding of stabilizer of any capacity with super enamelled copper winding wire of appropriate gauge and cleaning of rust, carbon, deposit etc. complete all as specified and as directed by Engr-in-Charge.

Fixing in replacement of dimmer stat 75 amps oil cooled single phase complete all as specified and as directed by Engr-in-Charge.

Fixing in replacement stabilizer ralely 150 to 200 Amp complete all as specified and as directed by Engr-in-Charge.

Supply & fixing controller control module panel for diesel generator DSE7320 with manual /auto electronics suitable for 40 to 250 KVA DG Set complete all as specified and as directed by Engr-in-Charge.

Supply and laying of 40 mm CPVC pipe SDR 11 & plain CPVC SDR 11 fitting including making connection with existing line including all accessories and fixing on wall and ground/ceiling or laying in floor complete including taking out old rusted/broken GI pipes, complete all as specified and as directed by Engr-in-Charge.

Supply and laying of 25 mm CPVC pipe SDR 11 & plain CPVC SDR 11 fitting including making connection with existing line including all accessories and fixing on wall and ground/ceiling or laying in floor complete including taking out old rusted/broken GI pipes, complete all as specified and as directed by Engr-in-Charge.

Supply and laying of 15 mm CPVC pipe SDR 11 & plain CPVC SDR 11 fitting including making connection with existing line including all accessories and fixing on wall and ground/ceiling or laying in floor complete including taking out old rusted/broken GI pipes, complete all as specified and as directed by Engr-in-Charge.

Taking down carefully unserviceable copper/aluminium point wiring (light, fan, socket or power)complete including fixture and fitting such as switches, ceiling rose lamp holder, regulators, sockets, light fittings, wooden terminal boxes, plastic laminated sheet cover, including taking down of DB’s, meter board any type complete all as specified and as directed by Engr-in-Charge.

M&L for point wiring with single core PVC insulated unsheathed 1100 volt grade cable with multi strand copper conductor of size 1.5 Sq mm FRLS (Nominal area) drawn through existing PVC conciled/conduit concealed in wall, ceiling with GI saddles GI screws, rawl plugs (concealed conduit wiring) with all fittings including Tee, Junction boxes and provision of pressed steel terminal box powder coated of suitable size with 3 mm thick laminated sheet cover for mounting switch sockets and regulators and drawing continuous earth wire of PVC insulated unsheathed 1100 Volts grade cable with stranded copper conductor of size 1.5 Sq mm (Nominal area) complete all as specified. Note: Cost for cutting, chasing and making good to existing surfaces are deemed to be included in the Quoted Rate.

(a) For one light point controlled by one SP switch

(b) For one fan/exhaust fan and wall mounted fan point controlled by one SP switch.

(c) For one bell point controlled by one No bell push

All as per Srl item No.68 here-in-before but for one 3 pin 5 Amps socket out let point on the same board controlled by one switch complete all as specified and directed by Engr-in-Charge.

All as per item No.68 above but for one 3 pin socket out let, 6 Amps on independent board with the cable 1.5 Sqmm size complete all as specified and as directed by Engr-in-Charge.

All as per item No.68 above but for one 3 pin socket out let, 16 Amps on Independent board with the cable 2.5 Sqmm size complete all as specified and as directed by Engr-in-Charge.

S & F socket outlet 5 pin, 6 amps flush type complete all as specified and as directed by Engineer-in-Charge.

S & F socket outlet 6 pin, 16 amps (Multi pin) flush type complete all as specified and as directed by Engineer-in-Charge.

S&F switch piano flush button type 6 amps single pole one way complete all as specified and as directed by Engr-in-Charge.

S&F switch piano flush button type 16 amps single pole one way complete all as specified and as directed by Engr-in-Charge.

S&F bell push flush button type 6 amps single pole one way complete all as specified and as directed by Engr-in-Charge.

S&F ceiling rose surface bakelite 2 to 3 terminals 65 x 50mm complete all as specified and as directed by Engineer-in-Charge.

S&F energy saving decorative box type batten light fitting surface mounted complete with high efficiency PMMA diffuser soft glare free light LED lamp 18/20 watt suitable for 120 volts to 270 volts of system efficacy not less then 90 lumen/watt, with all accessories, pre-wired, including lamp and providing flexible copper wire, twin core cable complete all as specified and directed by Engineer-in-Charge.Make:- Cat No : LUMILINEBS20WLED830SPCWH of havells Crompton Greaves/ Philips/Bajaj/Havells.

Taking down carefully the existing unserviceable ceiling / Exhaust fans/ Wall mounted fan of any make/ model and sweep from different sites in the building for overhauling / servicing after disconnecting carefully cleaning and checking unserviceable components, and replacing the defective components such as bearing, rubber bush/bolt, gunmetal bush, capacitor burnt windings flexible cord, shaft and painting etc., including assembling after lubricating the movable components and installing in its original position connecting, testing and commissioning all as specified and directed by the Engineer-in-charge. Note:- For Sl. Item No. 80 above Bearing/ Gunmetal bush/ rubber bush bolt/ capacitor / cord flexiable / stator/rotor and painting will be measured in paid seperately as under respective item.

M & L for rewinding of ceiling fans 1200/1400mm sweep of any make/model, including removal of existing burnt windings carefully from the slots,cleaning the slots thoroughly with necessary cleaning agent, applying slot insulation and rewinding with super enmelled copper winding wire of same gauge/same number of turns as that of existing and connecting the coils suitable to operate on 230 volts single-phase AC supply permanent capacitor type, tying the windings and applying air dry insulating varnish and drying the windings including replacing the defective components such as bearing, gun metal bush,rubber bush/bolt, capacitor,flexible cord, shaft and painting including assembling after lubricating movable components complete including testing complete all as specified and directed Note :- (1) Fan will be issued from AGE E/M store yard through gate pass. (2) Bearing/ Gunmetal bush/ rubber bush bolt/ capacitor / cord flexiable / stator/rotor and painting only will be measured and paid separately under respective item.

All as per item no 80 above but exhaust fan of 450/375/300mm sweep complete all as specified and directed by the Engineer-in-charge.

All as per item no 80 above but pedestalt fan of any sweep complete all as specified and directed by the Engineer-in-charge.

All as per item no 80 above but Wall mounting fan of any sweep complete all as specified and directed by the Engineer-in-charge.

Supply only ball bearing suitable for any fans of any Sweep complete all as specified and directed by the Engineer-in-charge.Make TATA, SKF

Supply only gunmetal bush suitable for ceiling fan / wall mounting fan of any make/model/ sweep of 1200/1400 mm and Exhaust fan of any sweep all as specified and directed by the Engineer-in charge.

Supply only twin core PVC flexible copper conductor of size 23/0076 all as specified and directed by the Engineer-in-charge

Supply only capacitor of 2.5 Mfd. AC 230/240 volts, 50 Hz complete all as specified and directed by the Engineer-in-charge.Make Epcos

Supply only capacitor of 3.15 Mfd. AC 230/240 volts, 50 Hz complete all as specified and directed by the Engineer-in-charge.Make Epcos

Supply only capacitor of 4.0 Mfd. AC 230/240 volts, 50 Hz complete all as specified and directed by the Engineer-in-charge.Make Epcos

SCHEDULE 'A' PART-II (Schedule of credit) Credit amount of Rs (Refer schedule of credit) for retrieved material mentioned in Sch 'A' Part-II of Tender documents in PDF form will be deducted offline during acceptance of tender of lowest bidder.

Note: (1) The repair has to carried out as and when required basis and accordingly site will be available in piecemeal wise and as directed by Enginer-in-Charge in the Air Force station at Jammu .

NATIONAL TRADING COMPANY