Annual repair for Mini Sectt. Phase 1 and 2 at Rohtak for the year 2022-23.

Amount

Regarding terracing of mud phaska covered with tiles or brick, in cement mortar by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1:3 (1 cement : 3 fine sand), including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded), all complete as per direction of Engineer-in-Charge. (HSR 30.9)

Providing and laying of conglomerate floor 40mm thick cement concrete topping 1:2:4 (HSR 10.8)

Providing and laying of 40 mm thick marble chips flooring, rubbed and polished to granolithic finish, under layer 31 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) and top layer 9 mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from 4 mm to 7 mm nominal size, laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 4:7 (4 cement marble powder : 7 marble chips) by volume, including cement slurry etc. complete. (HSR 10.20.1) Dark shade pigment with Ordinary cement

Providing and fixing of Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : (HSR 10.37.1) 25 mm thick

12 mm cement plaster of mix : (HSR 11.5.4) 1:6 (1 cement: 6 fine sand)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : (HSR 30.28.1) One more coats on old work (LR)

Distempering with 1st quality acrylic distemper (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade : (HSR 30.25.1)(LR)

Finishing walls with Acrylic Smooth exterior paint of required shade : (HSR 30.37.2) Old work (One more coat applied) (LR)

Renewing glass panes, with wooden fillets wherever necessary: (HSR 30.55.1) Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sgm)

P.H. work

Providing and fixing Unplasticised -PVC pipe clips of approved design to Unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. (HSR 9.59.2) 110 mm

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: (HSR 22.22.1) White vitreous chinaware Orissa pattern W.C. pan of size each 1144 2767 3911 580x440 mm with integral type foot rests

Providing and fixing vitreous chinaware dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: (HSR 22.32.1)

Providing and fixing white vitreous chinaware flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : (HSR 22.25.3) Range of two urinal basins with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing white vitreous chinaware flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : (HSR 22.25.4) Range of three urinal basins with 10 litre white P.V.C. automatic flushing cistern

Providing and fixing white vitreous chinaware flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : (HSR 22.25.5) Range of four urinal basins with 10 litre white P.V.C. automatic flushing cistern

Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of Engineer-in-charge) including Rack Bolt Screw Pair 115mm long without CP fittings complete in all respect. (HSR 22.221.2) Size 550 mm x 400 mm x 815 mm

Providing and fixing kitchen sink including making all connections excluding cost of fittings. (HSR 22.13.1) White glazed fire clay sink of size 600x450x250 mm

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (HSR 22.209)

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : (HSR 22.104.1) 15 mm nominal bore

Providing and fixing Unplasticised PVC connection pipe with brass unions: (HSR 22.101.2.1) 15 mm nominal bore

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. (HSR 22.124.1) 15 mm nominal bore, 105 mm long, weighing not less than 138 gms

Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately. (HSR 22.182)

500 Ltr. Capacity

200 Ltr. Capacity

1000 Ltr. Capacity

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. (HSR 22.88) 15 mm internal diameter of pipeline. (HSR 22.88.1)

20mm internal diameter of pipeline. (HSR 22.88.2)

25mm internal diameter of pipeline. (HSR 22.88.3)

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : (HSR 22.94) 15 mm dia nominal bore (HSR 22.94.1)

20mm internal diameter of pipeline. (HSR 22.94.2)

25mm internal diameter of pipeline. (HSR 22.94.3)

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 (HSR 22.108.1) 15 mm nominal bore

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube up to 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge. (HSR 22.38)

Providing and fixing 15 mm C.P. brass Laboratory cock swan neck of best quality (to the approval of Engineer-in-charge). (HSR 22.8.1) One way

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. (HSR 22.14.2.1) 32 mm dia

Providing and fixing required Stainless Steel Fitting of press fit design of rade AISI 304 conforming to JWWA G116 standard with V-profile or M profileand with 0-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. (HSR 22.135.1)

Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profileand with 0-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. (HSR 22.132.1) For 15.88 mm outer dia pipe

NAND CO-OP Labour and Construction Societyety

The Shiva Labour And Construction Co- Operative Society Ltd