GE 874/EWS-40/2020-21

Amount

Demolition of cement concrete (un reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and as directed.

Demolition of cement concrete (reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and as directed.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, and precast concrete arches etc.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth and getting out in any type of soil, complete all as specified & directed.

S&F Plain cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in foundations filling and mass concrete, complete all as specified.

S&F Brick work with subclass ‘B’ Modular bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 all as specified and directed

RCC M-25 Design Mix, (using 20mm graded crushed stone aggregates), as in foundations including raft, foundation beam, plinth beam etc, complete all as specified & directed by Engr-in-Charge

Form work to edges of concrete flats,treads floors and beam, complete all as specified & directed by Engineer-in- charge.

Supply and fixing TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete all as specified.

Supply and fixing TMT bars, 6 to 8 mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia as in stirrups complete all as specified.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, in any type of soil, complete all as specified and as directed.

Removal of excavated material to a distance not exc.50 m and depositing where directed at a level not exceeding 1.5 mtr above starting point, complete all as specified and directed

M&L RCC 1:1.5:3 (using 20 mm graded crushed stone aggregates) to waist slab of staircase & steps of stair case, chullah hoods: stairways ( except spiral stair cases) Incl steps ( square or spandril ) string pieces, carriages etc ,complete as specified directed.

Form work to staircases with sloping or stepped soffits incl risers and stringers (exuding landing)

M&Lrailing work in stair cases, stairs (framed )incl strings, treads, landings, balusters, hand rails etc, incl clestsm brackets complete as specified directed.

Plain cement Concrete 1:2:4 type-B1 (using 20mm graded crushed stone aggregate) as in copings, hold fasts plinth band, bed blocks and like slightly rounded or chamfered angles as directed including necessary form work and finishing the exposed surfaceof concrete all as per in relevent clause of SSR Part-I, complete all as specified and directed.

M&L RCC 1:1.5:3 (using 20 mm graded crushed stone aggregates) in slabs supported on walls, beams and coloumns in floors, roofs , landings , balconies, deck slabs and shelves and the like complete as specified directed.

M&L RCC 1:1.5:3 (using 20 mm graded crushed stone aggregates) work in to lintel band & roof band, cantilivers, bressummers, like over lintel 1.5 m span complete as specified directed.

Taking down cement plaster on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc.complete all as specified.

Walling of random rubble stone masonry uncoursed, well bonded, bedded and solidly hearted, built in cement mortar (1:6), complete all as specified and directed.

Description all as per item no above , but except stone complete all as specified and directed.

M&L for Plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in surface channels and drains, complete all as specified.

Precast cement concrete (1:2:4) using 20mm graded crushed stone aggregate as in landings, cover slab (for manholes etc), chullah hoods, chajjas, water troughs, shelves and similar articles with plain fair faces including chamfers, weatherings, throating etc. and setting in cement mortar (1:4) including necessary form work complete all as specified and directed by Engineer-in-Charge.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement complete all as specified.

15 mm thick rendering in CM 1:4 on other than fair faces of brick or stone masonry surfaces & finishing the surface in even and smooth without using extra cement complete all as specified.

Hard core of broken stone/boulders of gauge exc 63mm deposited spread and leveled in layers n exc 15cm thick watered and rammed to a true surface, complete all as specified.

M & L Cement concrete work in pavement/hard-standing of flexural strength 40kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less, complete all as specified and directed.

Forming contraction (Dummy) joints 65 mm deep x 10 mm wide filled with sealing compound grade 'A', complete all as specified and directed.

Forming construction joints 30 mm deep x 10 mm wide, filled with sealing compound 'A' grade, complete all as specified and directed by Engr-in - charge

Form work to sides soffits of floor or roof beams, beam haunchings , lintels, cantilevers, shelves including supports, overhangs etc and similar works rough finished complete all as specified & directed

Rolled mild steel works as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe 410W (Gde E-250), quality 'A' complete all as specified.

M&L for eves board iron framed work such as grills, gratings etc with ends of bars shouldered and or revited or forged in to spikes, framed guard bars ,barred irron doos;ladders: framed balusters , walk ways , railings frame work of water tanks, complete all as specified

6 mm thick E board ( classic) of size 610x 610 mm as in false ceiling fixed with aluminium snap grid frame work of same size as aluminium TEE of size 25x25x 1.50mm as in main runner. 25x25x1.25 mm thick aluminium Tee as in croos runner and aluminium angle of size 25x25x1.25 mm at the perimeter incl GI adjustiable suspender ofrequired length incl taking down dismantling existing old ceiling ofany description,complete all as specified

S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screwscomplete all as specified.

M&L 40 mm thick PCC 1:2:4 type B-0 (using12.5 mm graded crushed stone aggregate) as in floors, roof, landings, complete all as specified and directed.

Brushing neat neat cement slurry with 3.00 kg of cement per sq mt complete all as specified and directed.

M&L 5mm thick settting coat over 10 mm rendering using CM 1:3 100 mm hight asin skirting/ dados complete all as specified and directed.

M&L10 mm thick rendering in CM 1:6 on other than fair faces of brick or stone masonry surfaces & finishing the surface in even and smooth without using extra cement complete all as specified.

M&L 15 mm thick rendering in CM 1:4 on external surface plastering of other than fair faces of brick masonry or concrete surfaces & finishing the surface even and smooth without using extra cement complete all as specified.

M&L 5 mm thick rendering in CM 1:4 on ceiling surfaces finishing even and smooth without using extra cement complete all as specified.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, confirming to Fe-410-W (Gde E-250) Quality-A complete all as specified

S&F 1.00 mm thick mild steel, plain black sheet in gearth: covering todoor shutters tocovering dooe chowkats ( frames chullah hoods: water tank; water troughs;ducts; urinal troughs and funnels etc cut to sizes edges beaded if directed, holes punched; incl round headed screws, cut nails or reviets and fixed to wood or steel members etc with plain 40 m laop joints or welded/revited seams incl bending, turning up , mitred angles stopped ends, outlets as required.

Mild steel FI as in hold fasts and similar small articles fixed to chowkats, size 25mm x 3mm conforming to Fe-290 Gde E-165, complete all as specified and directed.

Preparation of new plaster surface of walls including cornices plaster etc, and applying three coats of white wash, complete as specified and directed.

Preparation of new plaster surface of ceilings including cornices plaster etc, and applying three coats of white wash, complete as specified and directed.

Preparation of new plaster surface of walls including cornices plaster etc, and applying two coats of cement base paint over a coat of approved primer, complete as specified and directed.

M&L preparation of new steel and Iron surfaces over 10 CM width or girth not other wise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified.

M&L 75mm thick PCC 1:3:6 Type C-2 (using 40mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finished the surfaces even & fair, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified.

M&L 50 mm thick PCC 1:3:6 Type C-1 (using 20mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finished the surfaces even & fair, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified.

Non skid coloured ceramic tiles 7 to 8mm thick square/rectangular area of each tile exc 0.06 Sqm but n exc. 0.11Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including 15mm thick screed bed in CM (1:4), over and including 25mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in sub base complete all as specified and directed.

Glazed ceramic coloured tiles (300x200) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified.

Factory Made Solid PVC Moulded Door Shutter with particle board, 28 to 30mm thick (styles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site all as specified and directed

2nd class softwood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified.

30mm thick 2nd class soft wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (divided into square with sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (b) supplied and fitted to chowkats complete, all as specified.

S & F Sheet glass ordinary quality, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified.

Mild steel butt hinges, medium weight, cold rolled,100mm long, complete all as specified.

Mild steel butt hinges, medium weight, cold rolled,75 mm long, complete all as specified.

S&F Aluminium anodised tower bolt, stove enamelled black, with bright bolt of 150mm long, complete all as specified.

S&F Aluminium anodised handle cast type anodised, with bright bolt of 100mm long, complete all as specified.

PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint, laid in trenches or in floor/walls as soil pipe, fixed, complete all as specified and directed.

PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint, laid in floor/walls/trenches as soil pipe(vent pipe), fixed, complete all as specified and directed.

PVC (SWR) floor trap of 75mm dia of outlet, plain with grating including jointing with solvent cement fixed, complete all as specified.

PVC (SWR) reducer 110/75mm fixed, complete all as specified.

S & F PVC (SWR) junction single ( sungle 'T' ) bends complete all as specified.

PVC (SWR) bends any radius 110mm bore, complete all as specified.

PVC (SWR) vent cowl for 75mm dia fixed, all as specified.

PVC (SWR) gully trap 125/110 mm setting and jointing with slo outlet, plain with grating including jointing with solvent cement fixed, complete all as specified.

S&F Bib taps 15mm bore of cast copper alloy chromium plated fancy type, screwed down, high presure with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule, and fixed, complete all as specified and directed.

S&F Angular stop cock with wall flange suitable for 15 mm bore for iron pipe and fixed complete all as specified and directed.

15mm dia GI steel water tubing ,medium grade ISI marked ,laid in trenches with and incl all fittings such as bends, elbows, tees, short pieces, diminishing pieces, union etc complete all as specified.

Steel water tubing 20mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceiling or laid in floors, complete all as specified.

Rotational moulded polyethylene water storage tank tripple layer cylindrical vertical with closed top 500 litre capacity hoisted and fixed in position, connecting to inlet and outlet pipe connections, with and including 20mm dia GI wash out with plug, complete all as specified and directed.

S&F 20mm bore gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe or brass ferrule fixed, complete all as specified.

PVC connection 15mm size with PTMT nuts on both ends of length 600mm fixed, complete all as specified and directed.

Vitreous china Wash hand basin, white, flat back of size 550x400mm including brackets, brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand and embeded in cement etc, complete all as specified.

PVC valve less syphonic action type flushing cistern 10 ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC flush pipe for low level cistern including all connection fixed, complete all as specified and directed.

15mm bore pillar tap fancy type cast copper alloy with capstan head, chromium plated, screwed down, high pressure with or without lettered 'Hot' or 'Cold' with long shank and fly nuts screwed for iron pipe or for brass ferrule and fixed complete, all as specified & directed

Construction of brick masonry staging for over head water tank 2.4m height from ground level including necessary earth work in any type of soil PCC 1:4:8 ) and RCC bracing and slab all as shown on drawing No. CESZ/TD-1101/2011 Sheet 1/1 dt 01/12/2011, complete all as specified and directed.

S & F Vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, white, with integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe of 32mm dia and anti-syphonage pipe etc, complete all as specified.

S&F 20mm bore gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe or brass ferrule fixed, complete all as specified.

M&L for Plain cement concrete 1:3:6 type C-2 concrete bed 100 mm below pipes (using 40mm graded crushed stone aggregate) as in surface channels and drains, complete all as specified.

Construction of 10 users septic tank (brick construction) including inlet and out let chamber with top of slab at ground level including necessary earth work and disposal of surplus soil to a distance not exceeding 50m supplying and placing vent pipe, in position to manhole cover brick construction and all other relevant works, complete, all as specified and shown on drawing No CESZ/TD-1/2015 Sheet 1/3 and 2/3 dt 22/02/2015, revised dt 21/03/2015.

M/S SS SHAH WALI & CO

patriotic builders