CWE/P-14/2020-21 SPECIAL REPAIR TO BLDG NO NP-09, NP-10, NP-11 AND NP-12 AT PATHANKOT UNDER GE (SOUTH) PATHANKOT

Amount

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust and including taking out existing roof treatments, brushing neat cement slurry with 3.0 Kg of cement per sqm and including 10mm thick rendering in cement mortar 1:3 mixed with WPC 3% by wieght of cement on fair faces of concrrete roof surfaces, finsihsed even and fair to receive treament on roof etc complete all as specified. Note: WPC shall be measured and paid separately

M & L PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in padding of average thickness n exc 75mm, and finishing the surfaces even & fair without using extra cement, complete all as specified and directed.

Supply only Integral water proofing compound.

Providing and laying of water proofing treatment of roof APP (Atactic Polyproplyllen) modified prefabricated five layer 3mm thick water proofing membrane, super thermply non woven polyester mat reinforcement of 160 gsm, weight of membrane @ 3.6 Kg/Sqm over a solvent based bitumen primer @ 0.3 Ltr per Sqm by the same manufacturer conforming to IS:3384-1986 , The membrane shall be laid using bitmun torch.The end lap should be 100 mm and the side lap must be minimum 75 mm the membrane shall be first laid up to the parapet wall junction and then shall be overlapped with another membrane (flashing) with an overlap covering up to a distance of 300mm. In case parapet height is less than/ up to 500 mm, membrane shall be terminated at the top of parapet.All rain water pipe opening shall be suitably sealed with the APP membrane all as specified and directed. (The rate includes for filling cracks in existing roof with cement putty using suitable bonding agent (shalcrate 42) before laying cement plaster)

M&L rendering 10mm thick on concrete surface in CM 1:3 in facia or edging of chajjas, ceiling and roof projection etc incl taking out pealed off plaster/concrete and making good to cracked RCC surface in true line /shape by providing RCC 1:2:4 type B1 using 20 mm graded crushed stone aggregate including all necessary form work to thickness at required at GF and FF finish even and smooth without using extra cement complete all as specified and as directed by Engr-in charge. NOTE- The rate will be inclusive of scafolding for single or double storey including making hole in brick work and making good in cement mortar.

Taking down cement plaster or cement line plaster on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc.complete all as specified.

M&L 5mm thick rendering in cement mortar 1:3 on fair faces of concrete surfaces as in ceiling & finishing the surface even and smooth without using extra cement, complete all as specified.

M&L 15mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete all as specified and directed.

M & L Brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6, complete all as specified.

M & L 15mm thick rendering in cement mortar 1:6 on fair faces of brick or stone masonry surfaces & finishing the surface even and smooth without using extra cement, complete all as specified.

M&L PCC 1:3:6 type C-1 ( using 20 mm graded crushed stone aggregates) as in copings, ,bed plates and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specified and directed.

M & L 75 mm thick cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in plinth protection etc and laid in alternate bays complete and finished the even & fair , laid to slope 1:12 and providings joints through out the thickness of plinth protection filed with mastic filling comprising one part of 01 bitumen 85/25 grade and three part of sand by weight all as specified and directed

M & L PCC 1:5:10 type E-2 (using 40 mm graded crushed stone aggregate) as in foundation filling and mass concrete all as specified and directed by Engr-in-Charge

M& L applying three coats of white wash including preparation of newly plastered surfaces of ceiling complete all as specified.

M& L applying two coat of white wash including preparation of old plastered or un plastered ceiling surfaces after complete removal/scrapping of existing treatment of ceiling by brooming down with steel wire brushes, scraping down smoke soot, moulds, moss and efforescent salt and trading oil and greasy spots etc complete all as specified.

M & L preparation of new plastered surface of wall and applying a coat of exterior emusion primer and two coat of exterior emusion paint complete all as specified

M & L preparation of old treated plastered surface of wall and applying a coat of exterior emusion primer and two coat of exterior emusion paint complete all as specified

M&L for preparation of new plastered surface and applying two coats of oil bound distemper over and including a coat of approved primer, complete as specified and directed.

M&L preparation of old plastered or un plastered wall surfaces after complete removal/scrapping of existing treatment and applying two coats of oil bound distemper over and including a coat of approved primer, complete as specified and directed.

M&L for leveling /edging of the disturbed planes/edges of old/new wall surfaces by using wall care putty of 1 to 2 mm thick on vertical surfaces to true vertical and horizontal lines of bricks/concrete walls finish to even and smooth with two layers of screylie wall putty complete.

Dismantling of floor hearth and wall tiling incl cement morter bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically described including removing rubbish/debris outside defence land complete all as specified and directed.

M & L PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in sub base for receiving floor tiles all as specified and directed by Engr –in Charge

M & L Joint free coloured/ printed glazed ceramic tiles (first quality) of size 300 x 450 x 7mm thick on vertical surfaces such as dado with highlighter etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over 10 mm thick rough cement plaster to recieve tiles in cement mortar 1:4 complete all as specified.

M&L 18 to 20mm thick granite (of approved type colour) work (table rubbed & polished) in skirting or vertical surfaces laid over and including 15mm thick cement screed (1:4) and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the colour of granite stone including cutting and moulding the edges where ever directed by Engr-in-charge, complete all as specified.

M & L Non-skid cermic coloured tiles 7 to 8 mm thick (square / rectagular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over screed bed 15 mm thick in cement mortar 1:6 complete all as specified.

M & L Non-skid cermic coloured tiles 7 to 8 mm thick (square / rectagular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, over screed bed 15 mm thick in cement mortar 1:6 complete all as specified.

M& L machine cut kota stone slab flooring 20 to 25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and (mirror) polishing complete & 20mm thick screed bed in cement mortar 1:6 complete all as specified.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L RCC nominal mix 1:2:4, type, B-1 (using 20mm graded crushed stone aggregate), as in slab supported on walls, columns in floors, roofs, landings, balconies and in shelves, complete all as specified.

M & L precast cement concrete (1:2:4) using 20mm graded crushed stone aggregate as in landings, cover slab (for manholes etc), drain cover, chajjas, water troughs, shelves and similar articles with plain fair faces including chamfers, weatherings, throating etc. and setting in cement mortar (1:4) including necessary form work complete all as specified and directed by Engineer-in-Charge.

M & L TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia complete all as specified.

M & L TMT bars, 6 to 8mm dia , cut to length, bent to shape required including cranking, bending spirally or hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia complete all as specified.

M&L for form work to sides and soffits of floor or roof beams, beam haunchings , lintels, cantilevers, shelves including supports, overhangs etc and similar works rough finished complete all as specified & directed

M&L 18 to 20mm thick granite (of approved type colour) work (table rubbed & polished) in jambs, pillars, window cills, cooking plateform laid over and including 15mm thick cement screed (1:4) and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the colour of granite stone including cutting and moulding the edges where ever directed by Engr-in-charge, complete all as specified.

M & L stainless steel sink 1mm thick for kitchen or laboratory wih plugs, washers and wastes including fixing bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mmx420mm bowl size 410mmx330mmx160mm fixed, complete all as specified.

S&F in repairs bib taps 15mm bore of cast copper alloy chromium plated fancy type with long shank with capstan head, screwed down, high presure , screwed both ends for iron pipe or for brass ferrule, fixed, complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fitting, head, shoes, bend, swan-nacks etc, including cleaning for refixing or removal to store .

S & F PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint laid in trenches/floor/walls as soil pipe(vent pipe)/weep holes, fixed, complete all as specified and directed.

PVC (SWR) shoe of 110mm bore, complete all as specified.

S & F 110 mm dia PVC (SWR) bends any radius complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5 Sqm each and removing from site complete all as specified.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm and n.exc. 4 Sqm each (without taking off sutters from the frames) complete all as specified and directed.

M & L 35mm thick 2nd class hard wood (kail) plain, framed, panelled door shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of 12mm thick veneered particle board with commercial face veneers fitted to chowkats of size as IS-1003 Part-01, complete all as specified and directed.

S&F for 35 mm thick shutter for door of 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc complete

M&L of two coat of synthetic enamel paint over a coat of pink primer on new wooden surface of any description, not otherwise described over 10 cm width or girth, incliding preparation of surfaces complete, all as specified.

M& L preparation of old painted wooden or wood based surfaces of any description not otherwise described, over 10cm width or girth including knotting and stopping as required and applying one coat of synthetic enamel paint, complete all as specified.

S&F for steel windows with tubular frame factory made with double shutter (wire gauged shutter & glass glazed shutter, wire cloth and glass panes shall be measured and paid separately) of size 79mmx39mm,16 gauge rectangular tubular frame with side hung shutter with glazing bars 12x3mm flat iron incl projecting type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 100mm long and including 10mm square bar grills complete, including two coats of synthetic enamel paint over one coat of red oxide primer all as specified & pattern shown in drg No CEPZ/ID-245/01 and 246/02 sheet ½ & 2/2.

S&F Aluminium anodised, barrel tower bolts of extruded section of size 150mm ISI marked and fixed, complete all as specified and directed.

S&F extruded aluminium alloy handles, fabricated type, anodised of size 150mm ISI marked and fixed, complete all as specified and directed.

S&F Mild steel sliding door bolts, stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolts plate and two on staple plate, 300mm long, ISI marked all as specified.

M & L factory made solid PVC puff door frame of size 90x55mm made out of 5mm thick plain colour PVC sheet with one or more rebate reinforced with MS square tube fixed in opening as per specification and drawings No CEPZ/TD-378 / 11 sheet No 1/1 etc complete all as specifed and directed.

S & F Butt hinges, mild steel cold rolled and fixed 100 mm, ISI marked complete all as specified and directed.

M & L Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), solid core panal design with 5 mm thick 3D wood grain printed (multi colour) PVC Sheet Polyurethane printed on the front face and 5mm Prelam PVC sheet on back face, complete all as specified and directed

M & L 1.25mm thick pressed steel frames with one coat of red oxide primer 105 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate, including cement concrete type C-1, 1:3:6 (using 20 mm graded crushed stone aggregate) as in filling hollow of frame with plain cement concrete and hold fast after taaring of hollow portion of frame complete all as specified and directed

M & L 1.25mm thick pressed steel frames with one coat of red oxide primer 125 x 60 mm with one or more rebates including necessary fixing lugs/hold fast duly tarred with bitumen and sanding with sharp clean sand, hinges, lock strike plate, including cement concrete type C-1, 1:3:6 (using 20 mm graded crushed stone aggregate) as in filling hollow of frame with plain cement concrete and hold fast after taaring of hollow portion of frame complete all as specified and directed.

S&F Galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aparture 1.18mm and fixed with tinned tacks or galvanised wire staples or nut and bolts including MS flat strip as required at site , complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone/ concrete, glazed with putty or fixed with beads, complete, all as specified and directed.

M & L 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified.

M & L Preparation new or previously untreated steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified.

M & L Preparation old treated steel surfaces of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

S&F door of Natural colour 15 micron anodized aluminium extruded section for chowkhats, shutter frame of door single side hung openable and chowkhats with one or more rebates, including M&L of beading, all necessary fittings floor spring heavy duty ISI marked, butt hinges, cleats, neosprine linings, 5.5 mm thick sheet glass (tinted) complete. The member shall made out of extruded aluminium sections comprising of followings:- (a) Chowkhats 125 x 44.45 x 1.75mm weight 1.36 Kg/ RM (b) Door shutter verticles member 85 x 44.45 x 1.80mm weight 1.302 Kg/RM (c) Door Shutter top member 83.50 x 44.45 x 1.70mm weight 1.243 Kg/RM (d) Door shutter lock Rail 83.5 x 44.45 x 1.70mm weight 1.243 Kg/RM Note :- The measurements shall be taken actual in position and net and exclusive of wastages cuts etc and any wastage shall be included in the rate quoted. The above sections shall be from JINDAL/INDAL/INDALCO/WALCO

S&F window of Natural colour 15 micron anodized aluminium extruded section for chowkhats, shutter frame of windows, vents ( Double shutters, glazed and gauged) etc. chowkhats with one or more rebates, including beading incl all necessary fittings, butt hinges, cleats, neosprine linings, 5.5 mm thick sheet glass (tinted), steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm with etc. The member shall made out of extruded aluminium sections comprising of followings:- (a) Window Shutter vertical member 47.62 x 45.45 x 1.74mm weighing 0.881 Kg/RM (b) Window Shutter top member 47.62 x 45.45 x 1.14mm weighing 0.607 Kg/RM (c) Window Shutter bottom member 47.62 x 45.45 x 1.14mm weighing 0.607Kg/RM (d) Chowkhats 101.6 x 44.45 x 1.75mm weight 1.36 Kg/RM Note :- The measurements shall be taken actual in position and net and exclusive of wastages cuts etc and any wastage shall be included in the rate quoted. The above sections shall be from JINDAL/INDAL/INDALCO/WALCO

S & F Continuous (piano) hinges, ISI marked mild steel, bright finish or electrogalvanised with width of flap (when open) 30mm complete all as specified and directed

Supply and fxing , 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate (ISI marked) complete including all neccesary welding if required all as specified.

M & L 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified.

M & L prelaminated particle, board 19/20mm thickness , exterior grade,prelmainated one side with deocrative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in cup board shutters and shelvs complete all as specified and directed

Supply and fxing in repairs, 100 mm dia sand cast iron soil waste and vent ISI marked in any length with or without ears with lead joints laid in floor complete all as directed

Supply and fxing in repairs, 100 mm dia sand cast iron soil waste and vent ISI marked in any length with or without ears with lead joints fixed to wall complete all as directed

Supply and fxing in repairs, Cast iron bends (any radius) diminishing pieces or tapers (larger bore measured), bore of pipe 100mm ISI marked, complete all as specified.

Supply and fxing in repairs, Cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branchs, ISI marked, bore of pipe 100mm, complete all as specified.

Supply and fxing in repairs, Cast iron bends (any radius) with duck's foot Or heel rest, bore of pipe 100mm ISI marked, complete all as specified.

S & F extra only CI bends if fitted with oval access doors for bore of pipe 100mm ISI marked, complete all as specified.

Supply and fxing in repairs, Cast iron floor trap of 75mm dia of outlet, plain with grating including jointing to waste pipe with solvent cement fixed in cement concrete 1:2:4, type B-1 complete all as specified.

Supply and fxing in repairs, 75 mm dia sand cast iron soil waste and vent ISI marked in any length with or without ears with lead joints laid in floor, complete all as directed

Supply and fxing in repairs, 75 mm dia sand cast iron soil waste and vent ISI marked in any length with or without ears with lead joints fixed to wall, complete all as directed

Supply and fxing in repairs, Cast iron cowl 50mm bore, complete all as specified.

Supply and fxing in repairs, 50 mm dia sand cast iron soil waste and vent ISI marked in any length with or without ears with lead joints fixed to wall, complete all as directed

Material & labour extra over cast iron pipes and fittings if lead joint is provided in lieu of cement joint; bore of pipe 75 mm complete all as specified.

Supply and fxing rotational moulded polythene water storage tank, white coloured, tripple layer cylindrical vertical with closed top 1000 litre capacity hoisted and fixed in position, including inlet and outlet pipe connections, 20mm dia and 15 mm dia GI pipes medium grade respectively, 20mm GI pipe medium grade over flow pipe 15 cm long wash out with plug including ball brass valves, high pressure, with polythene float and fly nut complete screwed for iron pipe or brass ferrule, 20mm bore complete all as specified and directed.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, Complete all as specified and directed.

M & L Steel water tubing of 20 mm bore ‘medium grade’ galvanized with all fittings fixed to walls and ceilings or laid in floors, complete all as specified.

Fixing only old steel water tubing of 20mm bore and connections in new or old position fixed to walls, ceilings and floors etc. including fittings as required, complete all as specified.

M & L Steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings fixed to walls and ceilings or laid in floors, complete all as specified.

Fixing only old steel water tubing of 15mm bore and connections in new or old position fixed to walls, ceilings and floors etc. including fittings as required, complete all as specified.

S & F 20mm bore gun metal globe or gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe fixed in repair, complete all as specified.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick masonry, complete all as specified.

Supply and fxing in repairs, PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC flush pipe for low level cistern including all joints fixed in repair, complete all as specified.

S&F in repair Vitreous china Wash hand basin, white, oval type of size 550x400mm including brackets, brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand etc, complete all as specified.

Supply and fxing in repairs, Vitreous china squatting pan (Orissa pattern) size 580 x 450 mm, white, with integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe of 32mm dia and syphonage pipe etc including provision of cement concrete bedding and complete, all as specified and as directed.

Supply & Fix in repair Vitreous china urinal half stall complete incl providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and incl 60mm long brass secrews, pointing around urinal in back in cement; fixed with angle valve, grating and union for discharge pipe complete all as specified and directed.

Supply and fxing in repairs,15mm bore swivel shower of PTMT (Minimum weight 40gms) any colour for fixing , including shower arm 15mm size 195 mm long with bend of 45 degree (Minimum weight 40gms) complete all as specified and directed.

Supply and fixing in repairs stop valve of cast copper alloy chromium plated with long shank concealed type screwed down high pressure screwed both ends for iron pipe or for unions 15 mm bore, complete all as specified.

Supply and fixing in repairs angle valve (ISI marked) of cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions 15 mm bore, complete all as specified.

M&L PVC connection 15mm size with PTMT nuts on both ends of length 450mm , complete all as specified.

M&L Tubular towel rail, ISI marked 60cm long between flanges , 20mm dia D type Brass Chromium plated incl necessary brackets, fixed with chromium plated screws and wooden/plastic cleats complete all as specified and directed.

M&L Shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 300gms) complete all as specified and directed.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified.

M & L for pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified (AS-3568 class III) complete all as specified.

M & L for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

M & L rolled mild steel works as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam,tee,angle, channel or flat sections) including distance pieces, cleats etc Fe -410 W (Gde E 250), complete, complete all as specified

M&L for preparation of new steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), including removing rubbish/debris outside defence land complete all as specified and directed.

M & L 75mm thick PCC 1:3:6 Type C-1 (using 20mm graded crushed stone aggregates) sa in sub floors complete all as specified.

M & L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed

M & L vibro compressed glossy finish rubber moulded precast concrete interlocking paver block shape and size as approved by GE confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and no pigment complete all as specified and directed

M & L mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required ; hooks (stay), heavy, for large gates ; hook and pintle hinges ; large hasps and staples ; chains ; hand made slinding bolts clamps ; hold fasts ; wall ties hooks forhanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165, complete all as specified and directed.

M & L central hole basin mixture valve, cast copper alloy 'fancy ype, chromium plated for mixing for hot & cold water screwed down high pressure with capstan head screwed both ends for iron pipe 15mm bore dia as oer Cat part No. 8350 of Prayag or Techno commercial equivalent complete all as specified and directed.

M & L second class hard wood plain fillet square, rectangular in section not exc 3 Sqcm Sectional area clean sawn, secured with nail complete all as specified and directed.

Supply and fxing Harrison rails(Curtain rails) (ISI marked), mild steel chromium plated 25mm dia pre -painted synthetic enamel paint of wooden finishes fixed with screws all as specified.

Supply and fxing in repair wooden (turned, weathered & mitred) brackets of Ist class hard wood pre polished with french polish and touch wood with cut hole suitable for 25 mm dia rod fixed with screws and gutties in wall, complete all as specified and directed.

Supply and fxing in repair wooden (turned, weathered & mitred) end caps with ornament and fixed to curtain rod with screw of design/shape complete all as specified and directed.

M & L 15mm dia hole for gas pipe in stones slabs such as in cooking platform and other similar situation complete all as specified and directed.

Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

M&L Point wiring for light/fan/bell point controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel terminal boxes (for mounting switches /sockets/ regulators/ceiling roses etc ) made of not less than 16 gauge MS sheet and 6cm depth covered with 3mm thick laminated bakelite sheet fitted with brass screw and washers and including 1.5sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green) (b) On RCC roof ceiling PVC conduit shall be provided on surface for fan with proper fixing clips all as directed.

All as per above item no 119.00 here in before but for one 3 pin socket outlet 5 amp on same board all as specified and directed.

All as per above item no 119.00 here in before but for one 3 pin socket outlet 5 amp on independent board all as specified and directed.

M&L Point wiring for 15 Amp socket point controlled by one switch with 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel terminal boxes (for mounting switches /sockets/ regulators/ceiling roses etc ) made of not less than 16 gauge MS sheet and 6cm depth covered with 3mm thick laminated bakelite sheet fitted with brass screw and washers and including 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green)

M&L Switch piano flush type 5 Amp single pole one way, (ISI marked), complete all as specified.

M&L switch socket outlet 6 pin, 5 & 15 Amp multipurpose 2 in 1 flush type,complete all as specifed.

M&L switch socket outlet combination 2 in 1 , 3 pin 5 Amp flush type all as specified & directed.

M&L socket outlet combination 2 in 1 , 3 pin 5 Amp flush type all as specified & directed.

M&L Stepped type electronic fan regulator 0 to 4/5 step , flush type, heavy duty with hum free snubber circuit complete all as specified.

M&L Ceiling rose, 3 terminal of bakelite 65x50mm two or three therminals isolated body fixed on PVC round block complete all as specified.

S&F in replacement sheet metal enclosure factory made (Double door) type IP-43 Protection. Isolated Neutral,Door earthing, cement spill protector, IK-08 complete, single pole and neutral, 240 volts, 50 Hz, 8 way with 200Amps rated copper bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified.

S & F in replacement existing unsv distribution board iron clad, with double door 4 way with IP-54,1K-09 protection, suitable for MCCB as incommer AC 415 Volts three pole with thermal release adjustable type (80% to 100 % ) and MCB as outgoing ,complete with appropriate size copper bus bar and neutral link complete with including one MCCB 3 pole 415 Volts 125 Amps rating with rupturing cap 25 KA of the same make as of distribution board & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site or directed by Engr-in-Charge (Outgoing MCB will be measured separately).

M&L MCB SP 6 to 32 Amp, 240V with 10KA breaking capacity of 'C' series 10 KA, including providing thimbles to outgoing cable all as specified and directed.

S&F MCB single pole & neutral 6 to 32 Amps, 240 Volts 'C' series, 10 KA, including providing thimbles to outgoing cable complete all as specified.

S&F in replacement existing UNSV light fitting with decorative box type fitting 4 feet long with blue coloured end caped for LED tube 1x16 W including LED tube 4 feet long of 16 W having bipin holder, connector block etc complete all accessories including necessary connection with cable of size 0.75 sqmm, three core flexible copper conductor cable PVC insulated and overall sheathed all as directed by Engr-in-chagre

Supply and Fix in replacement existing UNSV tube light fitting with LED 20W inverter batten type fitting 4 feet long aluminium extruded housing,IP-20 ,rated voltage 230 V, 50 hz, system wattage 20W +/- 10%, system current less than 102 mA, power factor more than 0.95, system lumen efficiency 100lm/watt,CCT 6500K, CRI more than 80, THD less than 30%, driver efficiency more than 85% complete all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed.

Supply and fixing in replacement existing unsv integrated LED bulk head light fitting 1X10 watts IP-65 protection connecting electricaly to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm all as required.

S&F in replacement existing UNSV sleek LED mirror light fitting 2 feet long 1x10 W including LED tube 2 feet long having ballast, bipin holder, connector block etc complete all accessories prewired and connecting electrically to ceiling rose usning PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as directed by Engr-in-chagre Notes for Srl item no 133 to 136 :- (i) Driver efficiency more than 85% ( Constant current driver) (ii) Non isolated type driver (iii) THD less than 20% (iv) LED driver current less than 60 mA (v) Efficiency of LED Chip more than 130 lm/watt (vi) Efficiency of LED Fixture 100 lm/watt (vii) Surge protection 2.5 KV & above as per IEC standard (viii) working humidity 95%RH (ix) LED Make Nichia /Philips lumiled/ Cree/Osram/Seoul/Bridgelux/Nationsear (x) Life 50000 Hrs at 70% lumes (xi) CRI more than 80 (xii) Working temp -10 degree to 50 degree C (xiii) Heat Sink extruded aluminum (xiv) junction temperature 85 degree C (xv) Body of fitting Extruded Aluminum (xvi) impact code Min IK 03 or more

( xvii) LM79 report from thir party (instead of company in house lab) NABL/UL accredited lab (xviii) LM 80 report from LED manufacturer (xix) Low/High voltage, reverse polarity, overload and short circuit protection inbuilt in fixture (xx) IP-20 . (xxi) Test certificates to be submitted before commencement of work/ claiming for payment . (xxii) Warranty certificate for minimum 2 years to be submitted from OEM.

S&F in replacement of existing UNSV CFL lamps with LED lamp 07 watt 230 volts complete all as specified and directed.

Supply and fix LED Lamp inverter type 09 watt 230 volts,50 Hz, ,lumen 900 lm, rated current 35 mA, CRI less than 80, Charging time 8 to 10 Hours, operating temperature -10 to 50 degree celcius,back up time 04 Hours, complete all as specified and directed.

Supply and fix bldg security light fittings with on Bldg of height exceeding 7.5 metre, LED security light fittings 25 watt, IP 65 having pressure die cast aluminium alloy housing, prismatic polycarbonate cover complete including making connection with 3 core copper flexible cable of suitable size including galvanised iron pipe bracket 0.90 metre long of 25 mm dia and fixing with bldg for fixing of street light fitting all as directed. Notes :- (i) Driver Efficacy – more than 85% ( constrant current driver).(ii) Driver Type – Potted (iii) THD - < 10% (iv) Led Driver Current – less than 750 mA (v) Efficacy of Led Fixtrue – 100 lm/watt ( minimum) (vi) Efficacy of Led Chip – more than 130 lm/watt (vii) Surge Protection – 4 KV & above as per IEC standard inbuilt in Driver and External SPD 5KV (viii) Working Humidity -10% to 90% RH (ix) Led Make – Nichia/Philips Lumiled/ Cree /Osram/ Seoul (x) Life – 50,000 hours at 70% lumens (xi) CRI – more than 70 (xii) Lens – Each Led shall be of High Power ( 1 to 3 watt only) with mandatory modular lens. (xiii) Working Temp – 0 to 50 degree C.

(xiv) Heat Sink – Pressure die cast aluminium (xv) Junciton Temp – 100 degree C (xvi) Body of Fitting – Pressue Die Cast with company logo / make engraved or embossed in housing LM 6 Grade.(xvii) Impact code – Min IK05 or more (xviii) LM79 report from NABL /UL accredited lab. (xix) LM80 report from Led Manufacturer.(xx) Low/High voltage, reverse polarity, overload and short circuit protection inbuilt in fixtrue.(xxi) MS Clamp fittings with nut bolts and GI bracket, junction box included in the rate.(xxii) Test certificates to be submitted before commencement of work/ claiming for payment .(xxiii) Warranty certificate for minimum 2 years to be submitted from OEM.

M&L Lamp holder Polycarbonate type with back plate having matching colour to holder for angle/batten fittings complete all as specified and directed.

S&F in repair single pole and neutral enclosure with a two pin and earth plug and socket complete with including one single pole MCB 240V, 20Amp complete all as specified and directed

Supply & Fix Ceiling fan AC single phase 230/240 volts of size 1200 mm sweep complete (BLDC) type BEE 5 star rated including blade ,down rod etc including connecting to ceiling rose all as required or directed. Note: Test report and Warranty certificate from OEM for minimum 2 years to be submitted before claiming for payment.

Supply & Fix Exhaust fan AC sinlge phase 230/240 volts of size 450 mm sweep steel body with louvre including connecting to ceiling rose all as required or directed including connecting to ceiling rose all as required or directed.Note: Test report and Warranty certificate from OEM for minimum 2 years to be submitted before claiming for payment.

Supply & Ventilation fan AC sinlge phase 230/240 volts of size 200 mm sweep having plastic body with louvre including connecting to ceiling rose all as required or directed including connecting to ceiling rose all as required or directed.Note: Test report and Warranty certificate from OEM for minimum 2 years to be submitted before claiming for payment.

S&F Geyser 50 Ltrs capacity, 230 volts, vertical type with BEE star rating 5 stars rating suitable for 8 bar pressure with nano polymer coated tank, incoloy heating element, rust proof ABS body etc incl necessay drilling, provn of anchor bolts of suitable size and making electrical connections complete all as directed by Engr-in-charge.

Supply and laying in replacement of existing unserviceable/ burnt submain wiring alongwith two single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of size 4 sqmm drawing into and including concealed PVC rigid non metallic conduit of 20mm dia , 1.8 mm wall thickness and single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of 4 sq mm as earth wire including cutting chases in brick wall, rendering in cement mortar 1:4 and making good the disturbed surfaces to match existing complete all as specified & directed. Note: (i) Two runs of 4 Sqmm single core PVC insulated copper conductor cable(FRLS) and one run of 4 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of 20mm dia , 1.8 mm wall thickness wiil be measured as a one unit. (ii) Proper colour coding is to be followed as per IS Specification. (iii) Test certificates of cables to be submitted before commencement of work/ claiming for payment. (iv) wiring shall be concealed/ on surface with rigid PVC conduit medium grade as per site requirement. (v) Electric Wiring test sheet before and after completion of wiring to be submitted before claiming payment

Supply and laying in replacement of existing unserviceable/ burnt submain wiring alongwith two single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of size 6 sqmm drawing into and including concealed PVC rigid non metallic conduit of 20mm dia , 1.8 mm wall thickness and single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of 6 sq mm as earth wire including cutting chases in brick wall, rendering in cement mortar 1:4 and making good the disturbed surfaces to match existing complete all as specified & directed. Note: (i) Two runs of 6 Sqmm single core PVC insulated copper conductor cable(FRLS) and one run of 6 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of 20mm dia , 1.8 mm wall thickness wiil be measured as a one unit. (ii) Proper colour coding is to be followed as per IS Specification. (iii) Test certificates of cables to be submitted before commencement of work/ claiming for payment. (iv) wiring shall be concealed/ on surface with rigid PVC conduit medium grade as per site requirement. (v) Electric Wiring test sheet before and after completion of wiring to be submitted before claiming payment

Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to galvanized earh lead wire of size 4.0 mm by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3 of SSR Part I, wire protected by dia 15 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI medium grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame, necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified. Note: The rate quoted include cost of 7.5 metre earthing wire with protection pipe.

Supply laying jointing and testing LT XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 95sqmm 3.5 core complete all as specified. Note : Earth work , sand cushioning, GI pipe , brick covering for mechanical protection will be measured and paid separately under respective item of Schedule.

Supply laying jointing and testing LT XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 50sqmm 3.5 core complete all as specified. Note : Earth work , sand cushioning, GI pipe , brick covering for mechanical protection will be measured and paid separately under respective item of Schedule.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth for foundation laying poles, stay assembly and laying of LT/HT cables in any type of soil and getting out, complete all as specified.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, in any type of soil, complete all as specified and as directed.

Removal of excavated material (soil) to a distance not exc 50m and depositing where directed at a level not exceeding 1.5mtr above starting point complete all as specified and directed

M & L Dry sand cushioning to UG cable 8 cm thick before laying and 15cm thick after laying complete all as specified and directed. Note:- 1.Dry fine sand of best available quality shall be used. 2.Punned thickness shall be made and paid.

M & L Sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified and directed.

M & L GI pipe light grade 50 mm bore with all fittings for cable protection fixed to walls/ poles or laid in trenches, under road/ under culvert/ under path/ under floor /on wall etc with fixing clamps, nuts bolts etc all as specified.

Material and labour for earthing with steel earth plate electrode of size 600x600x6mm thick buried directly in ground to a depth not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr deep below normal ground level connected to galvanized iron strip of size 32x6mm as earthing lead by means of nuts, bolts and washers of steel after welding of GI strip to earth electrode to the full length of earth plate, GI medium grade pipe 40 mm bore protection pipe upto test point, 20mm dia GI light grade watering pipe with funnel and wire mesh, RCC pit cover of size 300x300x40mm reinforced with XPM having weight not less than 4Kg/sqmm including 6mm thick MS bar handle made to shape, PCC pit with 1:3:6 type C1 with angle iron frame made of angle iron of size 40x40x4mm, adequate qty of charcoal dust and salt layers all around the earth plate, excavation , earth work in any type of soil, removal of excavated soil and returning filling in all as required at site complete all as specified in electrical plate No 3 of SSR Part-I and all as specified or indicated including testing on completion. NOTE :-Rates inclusive of necessary excavation in any type of soil, earth work, PCC pit, RCC cover, funnel with watering pipe, GI earth strip upto 7.5 m long for connecting to test point etc. all as required at site for complete earthing.

M&L for in replacement of existing UNSV cable end termination out door, heat shrinkable type suitable for XLPE/ PVC cables of size 25 sqm to 50 sqmm 3.5/4 core core with working voltage 1100 volts.

M&L for in replacement of existing UNSV cable end termination out door, heat shrinkable type suitable for XLPE/ PVC cables of size 70 sqm to 95 sqmm 3.5/4 core core with working voltage 1100 volts.

Notes : The Schedule of Credit amount shall be deducted from the total of this schedule(BoQ) to arrive at Contract Sum.

VIKRAM SINGH MANHAS

M/S BISHAN DASS AND SONS

Abrol construction co

Surya & Gautam Builders