PROVN OF OPEN TERRACE 4.00 X 3.50 M WITH NON SKID TILES OF BLDG NO P7 FLY PROOF WIRE MESHING FOR OFFRS MESS PL MESS PL STAFF AND OFFRS MD ACCN SPECIAL REPAIR TO TOILETS AT FIRST SECOND THIRD FLOOR STORE ROOM AT GROUND FLOOR INTERNAL PAINTING OF BLDG

Amount

Demoliton of cement concrete in ground floor paving n exc 15cm thickness (below or above ground level) complete all as specified and directed.

M & L for 15 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes finished even and rough complete all as specified and directed.

M & L pre polished machine cut kota stone (table rubbed mirror finished) slab flooring 20-25 mm thick over cement screet base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the kota stone slab complete all as specified and directed..

M & L for 12 mm thick machine Makrana white Marble tile of size 30CM X 20CM as in flooring over cement screed base, laid and jointed with white cement slurry mixed with pigment to match the shade of the marble including necessary grinding, rubbing, rounding to exposed edges and polishing in granite finish complete all as specified and directed.

Taking down cement plaster on wall raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed

M & L for rendering 10mm thick in cement mortar 1:6 on fair faces of brick/concrete surfaces on wall finished even and smooth without using extra cement complete all as specified and directed.

M&L preparing new plastered surfaces and applying two coat of oil bound distemper over a coat of primer on new plastered surfaces including 2mm thick of birla/ JK wall care putty complete as specified and directed. Note : work excuction by OEM as per standerd Practice by using painting equipment.

M&L preparing old plastered surfaces and applying two coat of distemper oil emulision on ceiling complete as specified and directed. Note :- Work shall be executed by original manufacturer / Authorised rep.

M&L for complete removel of exsiting treatment including cleaning of mortar drops smoke soot, moulds, moss, and efflorescent salts and trading oil and greasy spots etc and preparation of old plastered surfaces and applying two coats oil bound distemper of approved tinned on wall over 2mm one coat of birla/ JK wall care putty complete as specified and directed. Note :- Work shall be executed by original manufacturer / Authorised rep.

M & L for Marble work (Makrana white) 18 to 20 mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

Excavation in post holes (or similar holes) each not exc. 0.50 Cum, getting out, returning, filling and ramming earth or broken rubble mixed with earth around in layers not exc. 25 cm watering and removing surplus soil to a distance not exc. 50 m and making good surface as in soft / loose soil complete all as specified and directed.

M&L for 100 mm thick cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in floor finished even & fair etc complete all as specified and directed.

M&L for 40mm thick Cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) as in floor finished cement concerte surface even and smooth without using extra cement complete all as specified and directed.

Dismantling of wrought or mild steel any description and fixed in any position complete all as specified and directed.

S&F for rolled mild steel in stairs (framed) including stringers, treades, landing, balusters, hand rials etc. including cleats, brackets including welding work etc. complete as specified and directed.

M&L For preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of zinc chrome primer complete all as specified and directed.

M&L for rendering 5mm thick in cement mortar 1:3 on concrete surfaces of ceiling and finished surfaces even and smooth without using extra cement.

M&L for complete removel of exsiting treatment including old putty and preparation of old plastered surfaces of wall and applying two coat of 1st quality plastic emulsion paint (ready mixed) having VOC content less than 50 gms per litre of approved manufacturer of required shade and colour complete as per manufacturer specification, approved shade tint including alkali resisting primer, 2mm thick of birla/ JK wall care putty complete as specified and directed by engineer-in-charge. Note :- Work shall be executed by original manufacturer / Authorised rep.

M&L for preparation of new plastered surfaces of wall and applying distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete as per manufacturer's specification. Two or more coats on new work of approved shadelint including alkali resisting primer, 2mm thick birla/ JK wall care putty complete as specified and directed by engineer-in-charge. Note :- Work shall be executed by original manufacturer / Authorised rep.

M&L for complete removel of exsiting treatment including old putty and preparation of old plastered surfaces of ceiling and applying two coat of 1st quality plastic emulsion paint (ready mixed) having VOC content less than 50 gms per litre of approved manufacturer of required shade and colour complete as per manufacturer specification, approved shade tint including alkali resisting primer, 2mm thick of birla/ JK wall care putty complete as specified and directed by engineer-in-charge. Note :- Work shall be executed by original manufacturer / Authorised rep.

M&L for complete removel of exsiting treatment including and preparation of old plastered surfaces and applying two coat of 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms per litre of approved manufacturer of required shade and colour complete as per manufacturer specification two or more coats of new work of approed shadelint including alkali resisting primer 2mm one coat of birla/ JK wall care putty on ceilling all as specified and directed by engineer-in-charge.

M & L for preparation of Old painted wooden surfaces exc. 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M & L for preparation of Old painted steel surfaces over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

M & L for two or more coats of French polish as required over a coat of wood filler on surfaces of any description, width or girth including cleaning and preparing the Old surface complete all as specified and directed.

S&F for stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple complete all as specified.

S&F 3 mm thick sheet glass, ordinary quality, and glazing with oil putty in square/rectangle n exc 0.50 sqm in each pane including hacking out old broken glass from wooden / steel frame complete all as specified and directed

S & F Vitreous China Half stall type urinals, white, with geating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (excluding of fixing supply pipe, flushing cistern, flush pipe, trap and waste pipe) complete all as specified and directed.

S&F CP urinal spreader for fixing with 15 mm bore pipe complete all as specified and directed. Make : Hindustan / Parryware

S&F white vitreous china wash down water closet pan pedestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe complete all as specified and as directed. Make Parryware(Superfine), Cera (Ist Quality), Jaquar

S&F for Vitreous china wash down water closet pan (pedestal pattern) cascade type of size 375x620x770mm coloured/white with cistern (with twin flush fittings) complete including seat cover and fixing of flusing cistern, brackets, flushing pipe etc, comlete all as specified and directed (Make : Jaguar cat part No CNS WHT 353SPPZ or equivalent of make specified)

S & F PVC valve less, syphonic action type flushing cistern of 10 ltr capacity, low level with inlet, ball valve, float and handle including brackets incl PVC connection with CP brass nuts on both sides complete all as specified and directed.

S&F flush pipe of polyethelene of low and or high density or PVC 32mm dia for low level cistern

S&F wash hand basin size 555x425x195mm, oval type and fiding with I fixing in wall/platform comlete all as specified and as directed.

S & F of 32 mm bore Low Density Polyethylene Pipes (LDPE) of pressure rating 6 Kgf per Sqcm with and including all fittings and laid in trenches complete all as specified and directed.

Supply and fixing in repair15mm dia pillar taps, cast copper alloy, with capstan heads, chromium plated , screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S & F in repair bib tap15mm cast copper alloy chromium plated with crutch butterfly handle, screw down screwed for iron pipe or for brass ferrule etc complete all as specified and directed by the Engineer-in-Charge.

S&F two way angle cock 15 mm bore fancy type chromium plated, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe. Make : Parryware/Prayag/Jaquar

S&F in repairs brass CP two way angle cock 15mm chromium plate screw down screwed for iron pipe of brass ferrule etc complete all as specified and directed by EIC make: jaquar,COT-23059

S & F in repair 15 mm bore stop valves, cast copper alloy, fancy type chromium plated screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair brass chromium plated health faucet for EWC with 15 mm dia PVC pipe 1.00 m long including nut/washer complete all as specified and directed.

S&F for chromium plated toilet paper holder with flap fixed to wall with CP screws and wooden / plastic cleat complete all as specified and directed..

S&F in repairs PVC connection 15 mm dia size and 450 mm long with 2 Nos brass check nuts its washers complete all as specified and as directed.

S&F grating doom of stainless steel 100 mm dia complete all as specified and directed.

S&F in repair brass CP steel tubular towel rail 20 mm dia "D" type 60 cm long between flange aluminium anodised complete all as specified and directed. Make : Jaguar CAN 1118 BNM

S&F glass shelf 600mm long including fixed with CP brass screw and wood cleats / rowel plug with wall complete all as specified and directed. Make : Jaguar CAN-1171N

S&F CP towel ring round with round flange & brass screw and wooden/plastic cleats complete all as specified and as directed. Make : Jaquar CAN-1121BN

Cutting holes into or through brick walls built in cement mortar and making good the same in cement concrete 1:2:4 type B-0 or cement mortar 1:3 as required, superficial area of cutting not exc. 150 Sqcm complete all as specified and directed

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with brackets etc of 110 mm dia. complete all as specified and directed.

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with brackets etc of 75 mm dia. complete all as specified and directed.

S & F of 75 mm dia PVC (SWR) Multi floor trap, with grating including jointing with solvent cement complete all as specified and directed.

S & F of 75 mm dia PVC (SWR) Plain floor trap, with grating including jointing with solvent cement complete all as specified and directed.

S & F PVC (SWR) bends any radius of 110 mm dia provided with access door complete all as specified and directed.

S & F PVC (SWR) bends any radius of 75 mm dia provided with access door complete all as specified and directed.

S& F PVC(SWR) jnctions single(SingleT) equal or unequal, dia of bore 110 mm complete all as specified and directed by Engr-in-Charge.

PVC (SWR) 'P'/ `S trap bore 110mm/100mm complete all as specified and directed by Engr-in-Charge.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick(stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, complete all as specified and as directed.

S & F 75 mm size Butt hinges cast brass with mild steel hinge pin, bright polished complete all as specified and directed.

S&F 150mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed..

S&F Aluminium handles, cast type, anodized 150 mm size comp ISI Marked complete all as specified and directed

Taking up or down steel tubing and connections 15 mm dia complete all as specified and directed.

Taking up or down steel tubing and connections of 25 mm dia complete all as specified and directed

Taking up or down steel tubing and connections, of 20 mm dia complete all as specified and directed.

Supply & laying of 16mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings and wall / ceiling or laying in floors complete all as specified

Supply & laying of 20mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings and wall / ceiling or laying in floors complete all as specified

Demolition of concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Preparing surface of sunken slab and applying 15 mm thick plaster in cement mortor 1:4 mixed with and including integral water proofing compound both on floor and wall. The surface shall be cured and allowed to dry then applying Epoxy Resin coating polymer modified cementitious coating like brush bond of Fosroc, Pidilite and Bostic as per manufacturer's instructions both on floor as well as on wall and sunken floor shall be filled with graded cinder complete all as specified.

M&L PCC type C2, 1:3:6 (40 mm graded stone aggregate) as in sunken slab filling complete all as spd and as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for Non -Skid Ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm , in floors etc over and including15mm thick screed bed in cement mortar 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed

M&L for Coloured glazed ceramic tiles 450 x 350 7mm thick (digital type) on vertical surfaces such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in white or colored cement to match complete including 10 mm thick rendering on fair faces of brick work or concrete surfaces, in cement mortar 1:4 all as specified and directed for shade, pattern and laying of tiles complete all as specified and directed.

M&L PCC 1:2:4 type B1 (20mm graded stone aggregate), 25mm thick as in sub top layer floor and finished rough to receive the floor tiles.

M&L for 10mm thick Light shade vitrified ceramic tiles, exceeding 0.36 sqm but not exceeding 0.42 sqm as in floor / skirting surface etc, over and including 15 mm thick cement plaster in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement complete all as specified and directed.

M&L for solid PVC wall linning consisiting of 5mm thick wood grains printed PVC sheet inclusive of solvent cemment and fixing at site on PVC frameas per specification and drawing.

M&L for 5mm thick PVC sheet fillet of width 35mm for wall pannnelling inclusive of fixing on wall to make PVC frame as per specified and directed

Dismantling of wall and ceiling boards (fiber, pulp, insulation etc.) or insulation boards / blankets, any thickness including cover fillet complete all as specified and directed.

S&F anodised aluminium snap grid frame work for false ceiling size of grid 605x605mm complete all as specified & directed by Engr-in-charge

S & F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

M & L for 12 mm thick Gypsum Board in ceiling fixed with screw as per manufacturers instruction complete all as specified and directed.

M&L for providing & fixing at any height including scaffolding,welded mild steel wire mesh weight not less than 4.00 Kg per Sqm primed with Nitozzink primer (over, antirust coating after cleaning & after applying epoxy bound coat over damage concrete area) & applying 40mm average thick cement mortar with 10-15% polimer in the ratio 1:4 mixed with liquid intergral water proofing compound Nitobond AR manufactured by M/S Fosroc/M/S pidilite/M/S , in ratio as per recommendation of manufactures total chemical not less than 5% by weight of cement complete all as per manufacturer’s instructions and all as specified and directed.

Boring holes 5m deep in soil for Single under reamed piles and getting out and disposal of soil to a distance of n.exc 50m (dia of pile 300mm) complete all as specified and directed

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 Sqm on plan and getting out in soft / loose soil complete all as specified and directed.

M&L PCC 1:4:8 type D-2 (40mm graded agg) in fdn, sub base, mass concrete & cinder concrete etc. complete.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance n. exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M & L for Hardcore of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken bricks complete all as specified and directed.

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in foundation including rafts, footing, foundation beams, plinth beams, bases for columns, basement slabs, under-reamed piles and mass concrete complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in columns, pillars, piers, posps and struts complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M & L for providing reinforced cement concrete M-25 Design Mix using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately under respective item)

M&L RCC M-25 Design Mix (20mm graded aggregate) as in cantilevers, bressmumemrsm lintels over 1.5m span complete all as specified and directed..

M & L for use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar works not exc. 200 mm thick horizontal or slopping in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to sides of concrete foundation, footing, bases of columns, raft & raft beams, sides and soffits (if any) of foundation and plinth beams; and similar works; in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions in rough finished surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to edges of concrete flats, treads, breaks in floor, window cills, concrete railing, opening in concrete wall, sides of RCC slab, RCC / PCC bends in walls or similar work thickness exc. 10 cm and not exc. 20 cm in rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

M & L for mild steel TMT bars 8 to10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 8 mm dia and over upto as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed..

M&L for rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finished the surfaces even and fair without using extra cement complete all as specified and directed. Note : Liquid WPC will be measured and paid separately.

Supply only water proofing compound (liquid),ISI marked complete all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces and finishing the surface even and fair complete all as specified and directed.

M&L rendering 10 mm thick in cement mortar (1:4) on ceiling/chajja's finished surface even and smooth without using extra cement, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M & L for Preparing new plastered surfaces of ceiling and applying three coats of white wash etc complete all as specified and directed.

Cutting openings through walls for door, window and other openings or enlarging existing openings, etc., or cutting out defective masonry for under?pinning including providing, fixing and removing, shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises

S & F for powder coated aluminium door fame with shutter made out of following section complete fixed to position with hold fast all as specified & directed (a) chowkhat frame of size 83.50 x 44.45 x 1.87 mm thick weight @ 1.30Kg/RM (b) Style/Vertical member of size 47.62 x 44.45 x 1.90 mm thick weight @ 0.911Kg/RM (c) Top and bottom rail of size 95.25 x 44.45 x 2.00 mm thick weight @ 1.511kg/RM (d) Middle rail of size 49.91x 44.45x 2.01 mm thick weight @ 1.072Kg /RM (e) Top panel with 5.00 mm thick tinted glass fixing with rubber gasket. (f) Bottom panel with 5 to 6 mm thick Alumnium composite panel thick with clips (g) 100 mm dia round handle disc type -02 nos & Alu tower bolt 200mm - 01 No, Hinges 04 Nos each shutter. (h) Aluminum and PVC beading as per requirment as in fixing for paticle board & Glass, joing cleat including locking arrangement. etc

M&L double action floor spring for aluminium doors hydraulically regulated made up of minimum 1.5 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed including necessary cutting & making good to floor as per existing complete all as specified and directed. Make - Kelwyn / Amar

S & F Mild steel framed works such as grills,gratings,etc, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; walk ways; railings; framework of water tanks and similar work for portions framed and hung as gates, including pintle hinges, stops, hand made sliding bolts, etc conforming to Fe 290 Gde -E-165 complete all as specified and directed.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed by E-in-Charge.

M & L for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

S&F Non skid ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement over and including 20mm thick screed bed or bedding in cement mortar 1:6 complete all as specified and directed by EIC

M&L for concrete bed in P.C.C. 1:4:8 type D2 (using 40mm graded stone aggregate) to drain pipes including packing under and haunching against the sides of the pipes after laying & testing complete all as specified and directed for the following dia of pipes.

150mm dia.

200 mm dia

M&L for Reinforced cocrete pipe Spigot & socket type , class NP2, laid & jointed in cement sand mortar 1:1 with spun yarn complete all as specified and directed for the following size:-

150mm dia.

200 mm dia

S&F steel windows with side hung shutter incl box type butt hinges with bow handle,steel peg stay, tower bolts ( each shutter having two tower bolts 100mm long ) complete without glazing bars dovetailed or welded completev all as spd and as directed

Cutting holes in brick walls built in cement mortar for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required exc. half brick but not exc. one brick thick wall complete all as specified and directed.

Welding in repairs of metals exc 9 mm to 20 mm thickness n.exc 2.5cm in length

M&L preparing new plastered surfaces of wall and applying two coat of oil bound distemper over a coat of primer approved shade/tint complete all as specified & as directed.

M&L preparing old plastered surfaces of wall and applying one coat of oil bound distemper of approved shade/tint over all as specified & as directed.

M & L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces and finishing the surface even and smooth without using extra cement complete all as specified and directed.

Demolition of brick work built in cement mortar or cement lime mortar including removal to a distance exc 250 m but n.exc 500 m complete all as specified and as directed.

M&L for Preparation of wall of any description (new plastered surface) by washing, rubbing down and applying 2mm thick exterior wall care putty complete as specified and directed.

M&L for Preparation of wall of any description (old plastered surface) by washing, rubbing down and applying 2mm thick exterior wall care putty complete as specified and directed.

M&L for new Plastered.Surface of external wall of any description Finishing walls with Acrylic Smooth exteriorpaint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over andincluding priming coat ofexterior primerapplied @ 2.20 kg/10 sqm) ( The work of acrylic paint must got executed by OEM and and OEM should submit 5 yrs warrenty for the same. Painting must be done by using mechanical instruments only).

M&L for Preparation of old Surface of external wall of any description Finishing walls with Acrylic Smooth exteriorpaint of required shade on (Two ormore coat applied @ 1.67 ltr/10 sqm over andincluding priming coat ofexterior primerapplied @ 2.20 kg/10 sqm)

M&L for painting to old or previously unterated steel surfaces of any description over 10 cm in width or girth with two coats of synthetic enamal paint including prepartion of surface.

Demolition of Re-inforced Cement Concrete in any position and any description including cutting of reinforcement bars to facilitate demolition complete all as specified and directed. Note : Demolition materials shall be removed from site as directed by Engr-in-Charge.

M&L RCC Nominal mix type B0, 1:2:4 (12.5 mm graded stone aggregate) as in ,chajja and the like etc complete all as specified and directed

M&L RCC Nominal mix type B1, 1:2:4 (20 mm graded aggregate) as in fins, fascias louvres, parapets, and rallings exc 60 cm in height, newels, balustrade, ,chajja and the like etc complete all as specified and directed

M & L for use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to faces of walls, retaining wall, abutments, parapets, staircase railing and similar works including attached pillasters, buttressess etc in rough finished flat surface of concrete complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete all as specified and directed.

S&F Tubes, ‘medium grade’ galvanized, with all fittings and fixed complete to walls and ceilings or laid in floors of 25 mm dia including cutting /chasing in walls etc.

S&F tubes medium grade galvanized with all fittings and fixed to walls or laid in floors of 20mm bore

Roof treatment to be carried out as followed:- (i) M & L for preparing surfaces for roof treatment by removing all loose gravel, dirt oil grease and foreign matter by jet of dry air and cleanshould be sound clean and dry. All high spots should be removed. Surface to be finished to a smooth texture by mechanical means. Moss and lichens if any should be removed followed by treatment with fungicidal after treatment wash down throughly with clean water and allowed to dry before application . (ii) All cracks by cutting "v" groove and fill with PMC mortar (Polymer modified cement mortar) prepared in ratio as per manufacturers specification provide 30 mm x 30 mm coving with CM 1:4 admixed with chemical. (iii) Drilling holes of dia 18mm maximum upto half of the depth og the wall fix the PVC nozzels of dia 15mm and fix it with plug. Injecting cementitious grout within the the prefized nozzels underpressure using grout pump to fill all possible pores and holes (2 to 2.5 kg/sqcm) as specified by manufacturer. (iv) Prime the surface using primer and providing two coats of liquid applied ,solvent free elastomeric water proofing membrane shall be made of hydrocarbon free ppolyuretherene with atleast 90% solid content with necessary surface preparation ,coving, primer etc. The waterproofing shall be terminated on the top of parapet wall. (v) Spread of non woven geo textile of 140 GSM with overlap of 50mm in both side and saparation layer, the treatment to be protected by application of concreate screed (admixed with chemical @ 200ml per bag of cement) as per manufacturers instructions in required slope & 100mm thickness. For vertcal surface sprinkle fine aggregate after the application of second coat to get the mechanical key and to be protected by application of plaster complete all as directid by the Engr-in -charge. Make: Fosroc/ Pidilite/ Asian or Equivalent. (Note: (i) Work to be executed by authorized rep of manufacturers company. (ii) All water pipe line GI/CPVC to be removed from top surface for efficient execution of work & to be relaid in standard engineering practice along the walls. new pipeline of GI as required during shifting should be paid saperately. But no charges for refixing of old pipeline will be paid.)

M&L for 10mm thick Dark shade matt finished vitrified tiles in floors, exceeding 0.36 sqm but not exceeding 0.42 sqm set & jointed in neat cement slurry and pointed in coloured cement and incl 15 mm thick screed bed or bedding layers of cement mortar 1:6 to match Shade, pattern, laying etc of tiles complete all as specified & directed. Make : Somany/Johnson/Kajaria/Orient

M&L for 10mm thick Dark shade matt finished vitrified tiles in floors, exceeding 0.36 sqm but not exceeding 0.42 sqm set & jointed in neat cement slurry and pointed in coloured cement and incl 15 mm thick screed bed or bedding layers of cement mortar 1:4 to match Shade, pattern, laying etc of tiles complete all as specified & directed. Make : Somany/Johnson/Kajaria/Orient

Taking down carefully copper / aluminium point wiring (light, fan, switch, socket or power, Bell & Two way point) complete with fitting such as switches, sockets, ceiling rose, sketch light fittings etc, and making good the disturbed surface of walls and floors etc complete all as specified and directed.

Taking down carefully main switches DB's/ MCB DB's and making good the disturbed surfaces of walls etc complete all as specified and directed.

Taking down carefully copper / aluminium sub main wiring including teak wood batten / conduit and making good the disturbed surface of walls as directed.

M & L for Point wiring with PVC insulated and PVC unsheathed electric FRLS cable of 1100V single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area & including non metallic rigid PVC conduit ISI marked medium grade not less than 20 mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good disturbed surface of wall (cutting except on ceiling for fan point only, on ceiling instead of PVC conduit on surface will be used) & 1.5 sqmm green PVC insulated unsheathed copper conductor as a earth wire connected to earth dolly by providing lugs including 1.6mm thick anodised pressed steel sunken box covered with 3mm thick hylum sheet for mounting switches, sockets, fan regulators etc for the following complete all as specified and directed. Make of Cable : Polycab/Havell's/Finolex and Make of PVC conduit : Plaza/Harsh/Kalinga Premium/AKG:-

One light point/ fan point/bell point controlled by one switch

One 5 Amps socket out let point controlled by one switch on same board with other switches.

One 5 Amps socket out let point on independent board controlled by one switch.

All as per item no 147 above but wiring with 2.5 sq mm single core multistranded copper conductor for one socket out let 15/16 amps point on the independent board. Make of cable: Polycab/Havell's/Finolex and Make of PVC conduit: Plaza/Harsh/Kalinga Premium/AKG.

Supply and fixing in repair modular Switch 6 Amps single pole, one way complete all as specified and directed .

S & F socket outlet 2/3 pin combined 6A modular type two module complete all as specified and as directed.

S & F switch socket combination 6/16 Amps 6 pin modular type 3 module complete all as specified and as directed.

S & F modular metal box 3 way with necessary fittings complete all as specified and as directed.

S & F modular metal box 8 way with necessary fittings complete all as specified and as directed.

S & F modular white cover plate with frame 3 way with necessary fittings complete all as specified and as directed.

S & F modular white cover plate with frame 8 way with necessary fittings complete all as specified and as directed.

S & F blank plate PVC in liew of MCB, piano switch,Socket etc complete all as specified and as directed.

Supply and fix Ceiling rose surface bakelite 63.5mm dia three terminal, fixied in repairs complete.

Supply and fix double door SPN DBs 4 way, 240 volt with 200 Amp rated bus bar SPN of powder coated DB's suitable for housing MCB's/Isolater, Neutral link, Earth bar and Din ral complete.

M&L for Sub main wiring two single core PVC insulated unsheathed cable 1100 volts grade, 4 Sqmm size with multistranded copper conductor, drawn in but excluding non metallic rigid PVC conduit including PVC insulated unsheathed 4 Sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dolly complete.

S&F for MCB SPN 240 volts 32 Amps, 10 KA breaking capacity, 'C' type including connection with suitable size aluminium / copper lugs complete. Make-HPL / Indo Asian / ABB.

S&F in MCB SP 240 volts 5-32 Amps, 10 KA breaking capacity, 'C' type including connection with suitable size aluminium / copper lugs complete. Make-HPL / Indo Asian / ABB.

Supply and fixing LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixingLamp holder/ batten/angular fittings complete all as specified and directed.

Supply and fixing LED bulb 9 watt complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring,etc., and making good, cutting not exc 10 cm girth all as specified and directed.

Supply and fixing exhaust fan made of sturdy Steel metal body complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300 mm and grouting with nut , bolts & Fastenar on the wall by cutting and rounding wall and make good the disturbed surface and electric connection with 1.5 Sqmm three core PVC insulated round flexible copper conductor and sheathed cable complete all as specified and directed .

Earthing complete with galvanised steel earth plate electrode 600mm X 600 mm X6.30mm thick burried directly in ground (earth plate not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to Galvanized earth lead wire 4.0 mm dia by means of steel bolts,nuts, check nuts and washers test points made of GI strip 40X8mm, 10 cm long , PCC 1:2:4 type B-1 in pit, angle iron 25X25X3mm frame work with precast RCC 1:2:4 type B-1 cover reinforced with 8mm dia TMT bars @ 150mm C/C both ways and 12mm dia MS fabricated handle, medium grade GI watering pipe 20mm bore with funnel, wire mess and light grade GI protection pipe 40mm bore upto 5 m length for drawing in earth lead ,salt,charcol etc. including excavation and earth work in any type of soil , removal of surplus soil to a distance not exceeding 50m complete all as shown in electrical plate No. 3 of MES schedule 2009 part-I and connected complete all as specified including testing on completion.

PAPPU ROY CONSTRUCTION

M/s KUMAR ENTERPRISES

M/S Harsh Traders